Chromatographic analyses of tocopherols and tocotrienols in palm oil

Analyses of tocols (tocopherols and tocotrienols) in palm oil have been extensively reported in the past. However, due to the scarcity of individual tocotrienol standards, calibrations have mostly been carried out using only α-tocopherol as standard. Moreover, even if the individual tocotrienols are being used, their reliability is often questioned, because tocotrienols are highly susceptible to oxidation and deterioration. This paper reports on the study of the deterioration rate of individual tocotrienol standards upon storage as well as different calibration methods for the tocols in palm oil.     

Development and validation of an HPLC method for the simultaneous determination of tocopherols, tocotrienols and carotenoids in cereals after solid-phase extraction

The increasing interest in antioxidant properties of cereal and cereal-based products has prompted the development of a simple and reliable HPLC method for the simultaneous determination of important phytochemicals like tocopherols (T), tocotrienols (T3) and carotenoids. Separation was carried out on a Nucleosil 100 C(18) column, 5 μm (250 mm × 4.6 mm) thermostated at 25 °C, using a linear gradient elution system starting with methanol and ending with a mixture of methanol-isopropanol-acetonitrile. All separated compounds including the internal standard (α-tocopherol acetate) were eluted within 16 min and detected by dual detection: fluorescence for tocopherols and tocotrienols at 290 nm excitation and 320 nm emission and UV-vis photodiode array detection for lutein and β-carotene at 450 nm. Detection limits ranged from 0.2 μg/g (β-carotene) to 1.60 μg/g (α-tocopherol). The intra- and inter-assay coefficients of variation were calculated by using cereals with different levels of lipophilic antioxidants. The extraction method involved sample saponification and clean-up by solid-phase extraction (SPE). The extraction recoveries obtained using OASIS HLB SPE cartridges and dichloromethane as eluent were in the range of 90.2-110.1%, with RSD lower than 10%. The method was successfully applied to cereals: durum wheat, bread wheat, rice, barley, oat, rye, corn and triticale.     

Determination of tocopherols and tocotrienols in cereals by pressurized liquid extraction-liquid chromatography-mass spectrometry

A rapid analytical method including pressurized liquid extraction (PLE) and liquid chromatography-electrospray ionisation-mass spectrometry (LC-ESI-MS) has been developed for the determination of tocopherols and tocotrienols in cereals. The pressurized liquid extraction parameters were optimized in order to maximize the extraction efficiency. The use of methanol as extraction solvent at a temperature of 50 °C and a pressure of 110 bar, using one cycle of extraction with a static time of 5 min, provided the best results. A good LC separation was achieved using a C₁₈ column and a solution of 6.0 mM ammonia in methanol/water (97:3, v/v) as the mobile phase at a flow rate of 0.2 mL min⁻¹. MS coupling with an ESI interface in the negative ion mode was used as the detection technique. In the present work, it is shown that the addition of a base to the mobile phase is required to enhance the ionization of tocopherols and tocotrienols in negative ion mode electrospray ionization. The applicability of the method to cereal samples was confirmed. The reproducibility of the procedure was good, with relative standard deviations in the 6-10% range. The recoveries of added tocopherols from cereal samples ranged from 91 to 109%.     

Pressurized liquid extraction prior to liquid chromatography with electrochemical detection for the analysis of vitamin E isomers in seeds and nuts

Pressurized liquid extraction (PLE) was used to isolate tocopherols from seeds and nuts. Very clean extracts were obtained, which were injected directly into the chromatographic system. This enables rapid and simple control in food analysis. The PLE extraction temperature was set at 50 degrees C, with two cycles of extraction, a static time of 5 min, and acetonitrile as the extraction solvent. LC separation was accomplished on a Synergi Hydro-RP column with methanol-water (99.9:0.1, v/v) containing 2.5 mM acetic acid/sodium acetate buffer, as eluent. Coulometric detection, with a porous graphite electrode at +700 mV, was used. The method was successfully applied to the determination of alpha-, (beta + gamma)- and delta-tocopherols in almonds, sunflower seeds, hazelnuts and walnuts. The recoveries were in the 82-110% range. The results were validated with those obtained using sample treatment including alkaline hydrolysis.     

Determination of tocopherols in vegetable oils by CEC using methacrylate ester-based monolithic columns

The separation and determination of tocopherols (Ts) in vegetable oils by CEC using methacrylate ester-based monolithic columns has been developed. The effects of pore size of the monolithic columns were studied, and the composition of mobile phase was optimized. The optimal pore size of the monolith was obtained with 12 wt% 1,4-butanediol in the polymerization mixture. Excellent resolution between tocopherols was achieved within 10 min analysis time with a 99:1 v/v MeOH-aqueous buffer containing 5 mM tris(hydroxymethyl)aminomethane at pH 8.0. The LODs were lower than 2.3 microg/mL, and interday and column-to-column reproducibilities at 25 microg/mL were better than 5.6%. Using a 93:7 v/v MeOH-aqueous buffer, both tocopherols and tocotrienols (T(3)s) of grapeseed and palm oils were resolved. Application to the detection of olive oil adulteration with low-cost edible oils was demonstrated.     

Off-line coupling of pressurized liquid extraction and LC/ED for the determination of retinyl acetate and tocopherols in infant formulas

An analytical methodology including pressurized liquid extraction (PLE) as sample treatment to isolate retinyl acetate and tocopherols from infant formulas has been developed. The milk extracts were kept at −18 °C for 30 min and after filtration could be injected directly into the chromatographic system. Thus, a rapid and simple routine control method of these products is possible.

The parameters affecting both the extraction process and the liquid chromatography (LC) system were optimized. PLE was performed using one cycle of extraction during a static time of 5 min. Methanol was chosen as the extraction solvent for a temperature of 50 °C. Chromatographic separation was accomplished using a RP-18 column; the mobile phase used was methanol–water (94:6, v/v) containing 2.5 mM acetic acid/sodium acetate buffer. Electrochemical detection in amperometric mode with a glassy carbon electrode at +1100 mV was applied. The proposed methodology was successfully used for the determination of retinyl acetate, δ-tocopherol, (β + γ)-tocopherol and -tocopherol in different infant formulas. The analytes were evaluated in the same chemical form present in the samples. Recoveries were between 92 and 106%. A certified reference material of milk powder was also analyzed.     

Optimization and development of a high‐performance liquid chromatography method for the simultaneous determination of vitamin E and carotenoids in tomato fruits

A simple and reliable high‐performance liquid chromatography method was developed and validated for the simultaneous determination of lipophilic antioxidants in tomato fruits using C₃₀ column operated at 15°C and a gradient mobile phase based on acetonitrile/methanol/dichloromethane in a total run time of 30 min. Diode array and fluorescence detectors were used respectively for the detection of carotenoids (lutein, zeaxanthin, cryptoxanthin, lycopene, and β‐carotene) and vitamin E analogs (α‐, β‐, γ‐, and δ‐tocopherols, and tocotrienols). The best extraction yield of analytes in tomato fruits was achieved by employing ethyl acetate/hexane (1:1, v/v) after several treatments with various solvents. In addition, low extraction yields were obtained for carotenoids compared to tocopherols by adopting solid‐phase extraction as a second clean‐up step. The method was validated on the basis of recovery, precision, linearity, and limit of detection and quantification using spiked tomato samples. The method was applied to cherry and medium‐sized tomato fruits. Lycopene was found to be present in largest amount in tomato pulp, followed by β‐carotene and lutein. Due to its simplicity, rapidity, and efficiency, the method is suitable for routine analysis of lipophilic antioxidants in tomato fruits, and may also be applied to other vegetables of similar phytochemical profiles.     

Selective pressurized liquid extraction for multi-residue analysis of organochlorine pesticides in soil

A selective pressurized liquid extraction (SPLE) procedure capable of performing simultaneous extraction and clean-up has been demonstrated for multi-residue analysis of organochlorine pesticides (OCPs) in soil. The final method was performed at 100 degrees C for 3 x 10 min using acetone/n-heptane (1:1, v/v). Florisil was placed inside the extraction cell downstream the sample to remove interfering compounds. Extraction of two soil samples by SPLE gave a recovery which was over 80% for beta-endosulfan, endosulfan sulfate, p,p'-DDT and p,p'-DDE compared to PLE with off-line clean-up. The same trend was observed when applying the SPLE method to a certified reference soil sample (CRM 811-050) containing 13 OCPs, where the SPLE method gave 80-90% recovery vis-à-vis the PLE method with off-line clean-up. Feasibility of the SPLE method was further demonstrated by applying it to five real soil samples collected in Ethiopia.     

Pressurized liquid extraction of lipids for the determination of oxysterols in egg-containing food

Pressurized liquid extraction (PLE, ASE) was compared with the Folch procedure (a solid-liquid extraction with chloroform/methanol 2:1, v/v) for the lipid extraction of egg-containing food; the accuracy of PLE for the quantitative determination of oxysterols in whole egg powder was evaluated. Samples of spray-dried whole egg, an Italian vanilla cake (Pandoro) and egg noodles were used. Two different extraction solvents (chloroform/methanol 2:1, v/v, and hexane/isopropanol 3:2, v/v) were tested at different extraction temperatures and pressures (60 degrees C at 15 MPa, 100 degrees C at 15 MPa, 120 degrees C at 20 MPa). No significant differences in the lipid recovery of the egg powder sample using PLE were found. However, PLE of the vanilla cake and egg noodles with the chloroform/methanol mixture was not selective enough and led to the extraction of a non-lipid fraction, including nitrogen-containing compounds. In the same samples, the pressurized hexane/isopropanol mixture gave a better recovery result, comparable to that obtained using the Folch method. Cholesterol oxidation products of the Folch extract and the pressurized liquid extract of spray dried egg powder (obtained with hexane/isopropanol 3:2, v/v, at 60 degrees C and 15 MPa) were determined by gas chromatography. PLE performed under these conditions is suitable to replace the Folch extraction, because the differences between the two methods tested were not statistically significant. Moreover, PLE shows important advantages, since the analysis time was shortened by a factor of 10, the solvent costs were reduced by 80% and the use of chlorinated solvents was avoided.     

Molecularly imprinted polymers applied to the clean-up of zearalenone and α-zearalenol from cereal and swine feed sample extracts

A molecularly imprinted polymer prepared using 1-allylpiperazine (1-ALPP) as the functional monomer, trimethyltrimethacrylate (TRIM) as the crosslinker and the zearalenone (ZON)-mimicking template cyclododecanyl-2,4-dihydroxybenzoate (CDHB) has been applied to the clean-up and preconcentration of this mycotoxin (zearalenone) and a related metabolite, alpha-zearalenol (alpha-ZOL), from cereal and swine feed sample extracts. The extraction of ZON and alpha-ZOL from the food samples was accomplished using pressurized liquid extraction (PLE) with MeOH/ACN (50:50, v/v) as the extraction solvent, at 50 degrees C and 1500 psi. The extracted samples were cleaned up and preconcentrated through the MIP cartridge and analyzed using HPLC with fluorescence detection (lambda (exc)=271/ lambda (em)=452 nm). The stationary phase was a polar endcapped C18 column, and ACN/MeOH/water 10/55/35 (v/v/v, 15 mM ammonium acetate) at a flow rate of 1.0 mL min(-1) was used as the mobile phase. The method was applied to the analysis of ZON and alpha-ZOL in wheat, corn, barley, rye, rice and swine feed samples fortified with 50, 100 and 400 ng g(-1) of both mycotoxins, and it gave recoveries of between 85 and 97% (RSD 2.1-6.7%, n=3) and 87-97% (RSD 2.3-5.6%, n=3) for alpha-ZOL and ZON, respectively. The method was validated using a corn reference material for ZON.     

Determination of berberine and strychnine in medicinal plants and herbal preparations by pressurized liquid extraction with capillary zone electrophoresis.

A simple and rapid method for the determination of berberine and strychnine in medicinal plants and herbal preparations for regulatory purposes using a home-made pressurized liquid extraction (PLE) system with capillary zone electrophoresis (CZE) using ultraviolet detection at 254 nm was developed. The effects of pH, concentration of buffer, and organic modifiers in the electrophoretic separation were investigated. The buffer used for CZE contained 50 mM ammonium acetate, pH 3.1. The effect of temperature on the extraction efficiency of strychnine in medicinal plants by PLE was demonstrated. Comparable or higher extraction efficiency was achieved with PLE for strychnine in medicinal plants and berberine in herbal preparations compared to soxhlet extraction. The effect of matrix interference in medicinal plants and herbal preparations containing a number of medicinal plants samples using CZE was investigated by standard additional experiments. The reproducibility of the method using PLE with CZE was found to vary between 2.4 and 10.7% (n = 5/6) for different types of samples on different days.     

Determination of hexabromocyclododecane isomers in sewage sludge by LC‐MS/MS

A method has been developed to determine α, β and γ diastereoisomers of hexabromocyclododecane (HBCD), a brominated flame retardant, in sewage sludge, based on the ultrasonic‐assisted extraction (UAE) of samples with dichloromethane–ACN (1:1) and the subsequent clean‐up of extracts by dispersive solid phase extraction with primary–secondary amine. Levels of HBCD diastereoisomers were determined by LC coupled with ESI MS/MS. Evaluation of the matrix effect showed a high ion suppression for all the diastereoisomers studied, which was counteracted by using a mixture of labelled HBCD diastereoisomers as internal standards. This method yielded recoveries in the range of 79.6–112.5% with SDs equal or lower than 9.1 The limits of detection were 0.3 ng/g for α‐ and β‐HBCD and 0.2 ng/g for γ‐HBCD. The developed method was successfully applied to 19 sludge samples collected from the province of Madrid (Spain). In most of the samples, β‐HBCD was below the method detection limit, whereas α‐ and γ‐HBCD were quantified in all of the sludge samples, and γ‐HBCD was the predominant diastereoisomer in 63% of the analyzed samples and α‐HBCD predominated in the rest.     

Rapid assay of vitamin E in vegetable oils by reversed-phase capillary electrochromatography

A rapid capillary electrochromatographic (CEC) method for the analysis of vitamin E in vegetable oils is reported. Vitamin E consists of a group of eight isomers, tocopherols (TOHs) and tocotrienols. The separation of four TOHs (alpha-, gamma-, delta-TOH), alpha-tocopherol acetate (alpha-TOH-Ac), and an antioxidant compound, butylated hydroxytoluene (BHT) used to prevent TOH autoxidation, was optimized. The CEC experiments were carried out in a 75 microm inner diameter (ID) fused-silica capillary, partially packed with 3 microm C(18 )stationary phase (33 cm total length, 8.4 cm and 7 cm effective and packed lengths, respectively). The optimum mobile phase was a polar organic phase composed of a mixture of methanol-acetonitrile in the ratio 50/50 v/v containing 0.01% ammonium acetate, applying a voltage and temperature set at -25 kV and 20 degrees C, respectively. The tocopherols and the BHT were successfully separated within 2.5 min using the short-end injection method. Under these experimental conditions, repeatability of retention time and peak area, analyte detection and quantitation limits, linearity, precision, and accuracy were studied. The CEC method was applied to determine the content of TOHs in different commercially available oils of virgin olive, hazelnut, sunflower, and soybean. The extraction of vitamin E isomers from oil samples was achieved using methanol and a methanol-isopropanol mixture.     

Selective pressurized liquid extraction of polybrominated diphenyl ethers in fish

A fast and simple method for the analysis of polybrominated diphenyl ethers (PBDEs) in fish samples was developed using a one-step extraction and clean-up by means of pressurized liquid extraction (PLE) combined with gas chromatography-ion trap tandem mass spectrometry (GC-ITMS-MS). The selective PLE method provided to obtain ready-to-analyse extracts without any additional clean-up step, using a sorbent as fat retainer inside the PLE cell. Several PLE operating conditions, such as solvent type, extraction temperature and time, number of cycles and type of fat retainer, were studied. Using Florisil as fat retainer, maximum recoveries of PBDEs (83-108%) with minimum presence of matrix-interfering compounds were obtained using a mixture of n-hexane:dichloromethane 90:10 (v/v) as solvent, an extraction temperature of 100 °C and a static extraction time of 5 min in combination with three static cycles. Quality parameters of the method were established using standards and fish samples. Limits of detection and quantification ranged from 10 to 34 pg g⁻¹ wet weight and between 34 and 68 pg g⁻¹ wet weight, respectively. In addition, good linearity (between 1 and 500 ng ml⁻¹) and high precision (RSD % < 15%) were achieved. The method was validated using the standard reference material SRM-1945 (whale blubber) and was then applied to the analysis of PBDEs in fish samples.     

Simultaneous determination of tocopherols and tocotrienols in hazelnuts by a normal phase liquid chromatographic method.

A normal-phase high-performance liquid chromatography (NP-HPLC) method for the determination of tocopherols and tocotrienols in hazelnuts is reported. Three extraction procedures (with and without saponification) were assayed; the best results were obtained with a simple solid-liquid extraction procedure. Chromatographic separation was achieved using an Inertsil 5 SI column using isocratic elution with hexane/1,4-dioxane (95.5:4.5, v/v) at a flow rate of 0.7 mL/min. The effluent was monitored by a series arrangement of a diode-array followed by a fluorescence detector. All compounds were separated in a short period of time (17 min). The method proved to be rapid, sensitive, reproducible and accurate, allowing the simultaneous determination of all vitamin E homologues.     

Pressurized liquid extraction of pharmaceuticals from sewage-sludge

A method for the quantitative determination of ten pharmaceuticals in sewage sludge was developed by using pressurized liquid extraction (PLE) and HPLC-MS with ESI (HPLC-(ESI)MS). The PLE was optimized with regard to solvents and operational parameters, such as temperature, pressure, extraction time, and purge time. The optimum conditions were: 50 mM phosphoric acid/methanol (1:1 v/v) as the extraction solvent, temperature of 100 degrees C, pressure of 100 bar, extraction time 15 min, 2 cycles, flush volume 150% and purge time 300 s. All recoveries for pharmaceuticals were over 68% except for salicylic acid. The repetitivity and reproducibility between days expressed as RSD was lower than 8% for repetitivity and 10% for reproducibility. The LOD of all compounds was lower than 10 microg/kg of dry weight of sewage sludge. The method was applied to determine the pharmaceuticals in sewage sludge from two domestic sewage treatment plants (STPs). The samples were collected every three months between February 2004 and June 2005. Some pharmaceuticals were determined in the samples and naproxen showed the highest value (242 microg/kg of dry weight).     

Isolation of palm tocols using supercritical fluid chromatography

Crude palm oil contains 600 to 1000 ppm of tocols in the form of tocopherols and tocotrienols. These palm tocols have been isolated and analyzed in the past by various chromatographic techniques such as open column chromatography, high-performance liquid chromatography, as well as thin-layer chromatography. Supercritical fluid chromatography (SFC) has emerged as a more advanced chromatographic technique in recent years. The tocols present in palm oil are successfully isolated using SFC. Identification of these tocols is supported by various spectroscopic techniques such as 1H NMR, 13C NMR, and mass spectrometry.     

Active single-drop microextraction for the determination of gaseous diisocyanates

Heterocyclic amines (HAs) were analysed in meat extract samples using a new method based on pressurised liquid extraction (PLE) and liquid chromatography-tandem mass spectrometry. This method combines the use of a pressurised fluid with a triple quadrupole MS/MS system, resulting in benefits from both systems: high extraction efficiency and sensitivity. The effects of solvent type and PLE operational parameters, such as temperature and extraction time, were studied to obtain maximum recovery of the analytes with minimum contamination. HA extraction was best achieved using dichloromethane/acetone (50/50, v/v) at 80 degrees C for 10 min. Recoveries ranged from 45% to 79% with good quality parameters: limit of detection values between 0.02 and 1 ng g(-1), linearity (r(2)>0.997), and run-to-run and day-to-day precisions with relative standard deviations lower than 13% achieved at both low (0.20 microg g(-1)) and medium (1.0 microg g(-1)) concentrations. This method reduces sample manipulation and total extraction time by nearly four-fold compared to conventional solid phase extraction. The optimised method was validated using laboratory reference material based on a meat extract, and was successfully applied to HA analysis in several cooked beef samples.     

Solid-liquid extraction and cation-exchange solid-phase extraction using a mixed-mode polymeric sorbent of Datura and related alkaloids

Tropane alkaloids solid-liquid extraction methods were developed and comprised ambient pressure ones: extraction with hot solvent, extraction at room temperature, on ultrasonic bath as well as pressurised liquid extraction (PLE) techniques. The highest yields of l-hyoscyamine in methanol PLE method (3 x 5 min, 110 degrees C) and scopolamine extracted with 1% tartaric acid in methanol (15 min, 90 degrees C) were determined. A mixed-mode reversed-phase cation-exchange solid-phase extraction (SPE) procedure was optimised for simultaneous recoveries of L-hyoscyamine, scopolamine, scopolamine-N-oxide from plant extracts as well as quaternary alkaloid representative: scopolamine-N-methyl bromide. First three alkaloids were efficiently eluted (recoveries 80-100%) from an Oasis MCX cartridge with methanol-10% ammonia (3:1, v/v) solution, whereas for the quaternary salt tetrahydrofuran-methanol-25% ammonia (6:1:3, v/v) was used with recoveries 52-6%. HPTLC-densitometric assay on silica gel plates was elaborated at 205 nm without derivatization and included: single development (over a distance 9.5 cm) with acetone-methanol-water-25% ammonia (85:5:5:8, v/v) mobile phase for L-hyoscyamine and scopolamine separation, whereas for scopolamine-N-oxide and scopolamine-N-methyl bromide a second development (to a distance 5.5 cm) with acetonitrile-methanol-85% formic acid (120:5:5, v/v) was applied. Newly elaborated RP-HPLC-diode array detection method was performed on Waters XTerra RP-18 column with gradient of acetonitrile in 15 mM ammonia solution and alkaloids were baseline separated within 20 min. Both chromatographic methods were validated and their quantitative results were compared. Good correlation between HPLC and HPTLC quantitative results was measured (correlation coefficients of mean values were 0.92086 and 0.99995 for L-hyoscyamine and scopolamine, respectively). In the RP-HPLC method, which was from 1.5- up to 7-fold more sensitive than HPTLC, limits of detection (LOD) and limits of quantitation (LOQ, in bracket) were (in ng/microl) as follows: 0.25 (0.82) for L-hyoscyamine, 0.29 (0.97) for scopolamine, 0.13 (0.45) for scopolamine-N-oxide and 0.58 (1.91) for scopolamine-N-methyl bromide. By the use of the optimised chromatographic methods, 14 various samples from the leaves and fruits of Datura sp. were screened for L-hyoscyamine and scopolamine contents and the most promising samples were established.     

Pressurized liquid extraction and microwave-assisted extraction in the determination of organochlorine pesticides in fish muscle samples

This paper describes a comparative study of 2 extraction methods, pressurized liquid extraction (PLE) and microwave-assisted extraction (MAE), for the determination of organochlorine pesticides (OCPs) in fish muscle samples. In both cases, samples were extracted with hexane-acetone (50 + 50), and the extracts were purified by solid-phase extraction using a carbon cartridge as the adsorbent. Pesticides were eluted with hexane-ethyl acetate (80 + 20) and determined by gas chromatography with electron-capture detection. Both methods demonstrated good linearity over the range studied (0.005-0.100 microg/mL). Detection limits ranged from 0.029 to 0.295 mg/kg for PLE and from 0.003 to 0.054 mg/kg for MAE. For most of the pesticides, analytical recoveries with both methods were between 80 and 120%, and the relative standard deviations were < 10%. The proposed methods were shown to be powerful techniques for the extraction of OCPs from fish muscle samples. Although good recovery rates were obtained with both extraction methods, MAE provided advantages with regard to sample handling, cost, analysis time, and solvent consumption. Acceptable validation parameters were obtained although MAE was shown to be more sensitive than PLE.