聚苯胺薄膜电极上示差脉冲伏安法可逆波理论研究

本文提出了聚苯胺(PANI)薄膜电极上示差脉冲伏安法可逆波理论,经验证理论和实验结果相符合.     

Spectrophotometric and gravimetric determination of sulfur in sebacate-base lubricants

Sulfur is determined in sebacate-base lubricants spectrophotometrically and gravimetrically. In the spectrophotometric method, a 0.2–0.3-g sample is treated with mixed acids, magnesium chloride is added, and the solution is evaporated to dryness. The sulfate is reduced to hydrogen sulfide by treatment with a mixture of hydriodic. hypophosphorous, and hydrochloric acids, and the hydrogen sulfide is distilled into ammonia solution. Lead citrate reagent is added and the brownish yellow color of lead sulfide sol is measured. An improved technique and apparatus for the distillation is described. In the gravimetric method, a 5-g sample is treated with mixed acids, antimony and tin are volatilized by treatment with hydrobromic acid, and sulfur is precipitated as barium sulfate. The recommended range of the spectrophotometric method is 0.005–0.15%,and that of the gravimetric method is 0.01–1% sulfur.     

水性聚氨酯的制备及其性能的研究

本文以琥珀酸酐与三羟甲基丙烷反应,制得了含有羟基和羧基的酯类亲水性单体,并以此单体与ＴＤＩ和ＰＰＧ－１０００反应,制得了含有羧基的聚氨酯预聚体,在三乙醇胺水溶液中分散得到了水性聚氨酯（简称ＷＰＵ）。本文对预聚体的溶剂种类和用量,对乳胶粒的大小及形状的影响进行了研究,确认溶剂的用量越大,乳胶的粒径就越小;以丙酮作溶剂,乳胶粒为棒状或橄榄球状,而以丁酮为溶剂,得到的乳胶粒为圆球状。通过改变亲水单体的用     

用计算全息法检测卡塞格林系统主镜

为实现对卡塞格林光学系统中的非球面主镜表面面形的高精度检测,设计了一种二元位相型计算全息图(CGH)。介绍了工作原理,对CGH的相位模型参数的优化设计、衍射次级分离以及台阶位置与深度计算等关键问题进行了讨论。通过引入虚拟玻璃的概念快速建立非球面检测模型,针对卡塞格林系统主镜中心开孔的特点,通过加入同轴载波实现了衍射次级的完全分离,相比目前常用的倾斜载波方法简化了相位量化复杂度,数值仿真计算出了最优的台阶深度,降低了加工难度。给出了相应的设计方法及实例,研制投产了CGH。测试得到主镜面形的均方根误差为0.018λ,并与传统补偿器结果(RMS=0.019λ)进行对比,两者测试结果吻合,验证了该设计与检测方法的正确性,该设计方法简单快捷,适用于卡塞格林光学系统主镜面形检测。     

N,O-羧甲基壳聚糖的合成和性质研究

采用多段升温法将壳聚糖改性,合成了取代度为1.84、平均分子量为3.08×105、等电点为7.28的N,O-羧甲基壳聚糖(CMC),分别用紫外光谱、红外光谱、荧光光谱对其结构进行了表征,并对其水溶液的Zeta电位、电导率、表面张力以及水分散体系中羧甲基壳聚糖微粒的粒径分布进行了研究.结果表明, N,O-羧甲基壳聚糖具有表面活性;介质的pH值和浓度对羧甲基壳聚糖溶液的稳定性有很大的影响.     

Determination of free, total, and esterified cholesterol by high-performance liquid chromatography

A method is described for measuring free, total, and esterified cholesterol in blood serum in which reversed-phase liquid chromatography is used and the eluate is monitored at 200 nm. The sample for total cholesterol is prepared according to the Abell-Kendall procedure, and for free cholesterol an extract of serum--isopropanol (1:5, v/v) is used. The column is a muBondapak C18, 10 micrometers, and the mobile phase for total cholesterol is isopropanol--acetonitrile (50:50, v/v); for free cholesterol, it is isopropanol--acetonitrile--water (60:30:10). An approximation of the free cholesterol, triglycerides, and individual cholesteryl esters is obtained from single chromatograms of isopropanol extracts of serum if the first mobile phase is used. In a comparison study with the Abell-Kendall method for total cholesterol, the correlation is excellent and the precision is acceptable.     

Wastewater treatment using nanomaterial quaternary photocatalyst ZrCdPbO4 - Removal of colour pollutant by an eco friendly process

Pollution of environment is a major issue and has drawn attention of researchers throughout the globe. Water is polluted by various means like excretion of various industries and house releases, for example release of yarn, paper, and cloth industries etc. Present investigation consists of removal of such a pollutant. For this, synthesis of a novel quaternary nano particle sized photocatalyst ZrCdPbO₄ is carried and its characterization by different analytical techniques is also carried out. This is further used for removal of colour pollutants from the environment and Erythrosine-B is considered as a role model. Effect of various operational parameters like pH, concentration of dye, amount of photocatalyst, irradiation power etc. is studied, maximum degradation condition is extracted, and it is observed that reaction follows pseudo first order kinetics. Scavenger study suggests the participation of OH free radical in the reaction. Complete degradation of the dye in presence of light and photocatalyst is reported here by. Reusability of the photocatalyst is tested and is found to work up to five cycles efficiently.     

A Study on Alkyl Polyglycosides of the Starch

The alkyl polyglycosides (APG) is new type the surfactants that is made by regenerationresource of the starch and the grease, since the nineties of 20th century it is energetically exploited ininternational extent. APG not only good in surface activity, but also plenty on bubble, thin greasyand stabilization, there are good decontamination, compatibility, innocuity, not incitation and uniquefunction that organism decomposition of swiftness and downrightness, and so on.APG is to get production that loses one molecule water with half condensation aldehyde hydroxyand sebum alcohol hydroxy under acid catalysis. The production not is one simplicity compound, butis one of sugar polymerization degree, so it is mixture of the alkyl single glucoside, the alkyl twoglucoside and the alkyl three glucoside.Author synthesizes the surfactants of the alkyl polyglycosides, with the oleaster and potato starchand sebum alcohol, that was chosen to use duality system activator of plant acid and p-toluene-sulfoacid for the first time. The adoption way is that the lower alkyl polyglycosides is firstly formed byreaction of lower alcohol with starch then exchanged with high alcohol to obtain APG. The study isto make certain most technics condition, determining capillary tension and the pastern sheafdeepness of critical, calculating HLB value, determining construction by 1R.To synthesize principium:Peroration :[1]Duality system activator of plant acid and p-toluene-sulfo acid is compare idea activator that was the lower alkyl polyglycosides is firstly formed by reaction of lower alcohol with glucose then exchanged with high alcohol to obtain high alkyl polyglycosides. The advantage is that it overcomes agglomeration, there is reaction entirety, high of sugar transform ratio, reaction time short.[2]Most good reaction temperature is 90～ 170℃, the dosage of activator is 0.5%～0.9%, the mated ratio: The APG of glucose basic butane ratio starch is 5:1, the APG of potato starch basic glycol ratio starch is 6:1, the APG of the oleaster starch basic glycol ratio starch is 12:1, the APG of the mealiest starch basic glycol ratio starch is 6:1, the product of complex is good property.[3]The alkyl polyglycosides is the products of surfactant. IR determines the functional group of the products. On the basis of group of the hydrophile and to close on oil, that the feature peak of α-1, 4- glucoside.[4]The capillary tension of the APG is 26.8～31.0mN/m, the HLB value is 16～18, the products is better emulsifying agent of water- solubility. (O/W).     

Spectrophotometric determination of pentaerythritol tetranitrate (PETN) in waste water from lead styphnate primer plants

An accurate spectrophotometric method is proposed for the determination of pentaerythritol tetranitrate (PETN) in waste water from lead styphnate primer plants by use of phenoldisulphonic acid. The waste water is filtered through a sintered glass crucible and the PETN is determined in the filtrate and the residue. In the determination of PETN in the filtrate, sodium hydroxide is added and the PETN is extracted with methylene chloride (in alkaline solution, styphnate and TNT are not extracted). The methylene chloride solution is then evaporated to dryness, the residue is treated with a solution of phenoldisulphonic acid in sulphuric acid, water and ammonia are added, and the yellow colour is measured. In the determination of PETN in the residue, the PETN is dissolved in acetone, an aliquot of the acetone solution is treated with water and sodium hydroxide, the PETN is extracted with methylene chloride and the colour is developed as above. Various factors affecting the determination were investigated. The solubility of PETN in water was studied.     

山东省主栽果树生殖器官中稀土与微量营养元素的相关性研究

通过对山东省5大类主栽果树20余个树种的花粉、种子和果实稀土与微量元素自然含量进行分析比较, 认为稀土(RE)与微量元素在各树种花粉中平均含量顺序为Fe＞Zn＞B＞Cu＞Mn＞RE, 种子中B＞Fe＞Zn＞Mn＞Cu＞RE, 果实中Fe＞B＞Zn＞Cu＞Mn＞RE. 各元素在各生殖器官中的自然分布因树种而有很大差异. 但基本规律类同, 即花粉＞种子＞果实. 花粉富集各种微量营养元素的能力都很强. 花粉和果实稀土与微量元素之间绝大多数呈正相关, 种子大多呈负相关, 但相关性均不显著.     

D241树脂分离纯化黄芩总黄酮的研究

本文研究了用241树脂分离纯化黄芩总黄酮的方法和工艺。实验结果表明：D241树脂对黄芩总黄酮的静态交换容量是77mg/ml树脂。在pH11.0、流速2.0BV/h、提取液中总黄酮浓度17.5mg/ml条件下，D241树脂对黄芩总黄酮的动态交换容量为43.8mg/ml。用60％甲醇作为黄芩总黄酮洗脱剂，在PH4.0、洗脱流速1.5BV/h条件下，4．5BV洗脱剂即可完全洗脱被D241树脂交换的黄芩总黄酮。与酸沉淀法相比较，经过除去果胶，总黄酮纯度由33．34％提高到74．9％，粗品收得率由11.52%降低至4.83%；经过D241树脂分离纯化，其纯度达到91.5%，产品收得率3.54%。     

钕掺杂磷酸盐微晶玻璃的制备及表征

利用熔融和晶化技术制备掺钕磷酸盐玻璃陶瓷。 采用差热分析、X射线衍射、扫描电子显微镜、紫外 可见 近红外分光光度计及荧光光谱仪对材料进行表征和分析。 结果表明,在490～540 ℃核化1～2 h,在550 ℃晶化1～3 h,可制得主晶相为Al2SiO5的透明玻璃陶瓷。 其透过率可达69%,晶粒平均尺寸为90 nm,并随热处理时间的增加逐渐增大,但透过率降低。 由于Nd3+在热处理后进入到Al2SiO5晶相中,使荧光谱线在1 056 nm处峰值比原始玻璃强度大。     

微波消解-ICP-MS测定电镀污泥中的重金属

采用微波消解系统对某电镀污泥进行消解,利用ICP-MS对污泥中的重金属进行测定。称取制备后样品,置于消解罐中充分反应后,赶酸、定容后利用电感耦合等离子体质谱法进行测定。电镀污泥中的铬为18845.2mg/kg、镉为10.3mg/kg、镍为5200.0mg/kg、铅为189.7mg/kg、铜为3271.7mg/kg、锌为49632.6mg/kg。测定结果表明所检测项目工作曲线线性关系好,相关系数r均大于0.999。铬加标回收率在91.6～97.7%之间、镉加标回收率在92.0～97.0%之间、镍加标回收率在95.1～98.0%之间、铅加标回收率在94.3～95.2%之间、铜加标回收率在97.1～102%之间、锌加标回收率在96.3～98.7%之间,均满足相关测定要求。计算的潜在生态危害系数、潜在生态危害指数结果表明,电镀污泥中的铬、镉、铅、铜、锌为轻微生态危害,镍为强生态危害;潜在生态危害指数RI计算值为216.69,属于中等生态危害。     

Application of solid-phase microextraction and gas chromatography-mass spectrometry to the determination of volatile organic compounds in end-exhaled breath samples

Analysis of exhaled air is of particular interest as an indicator of health as well as a tool for the diagnosis of diseases. It is also a very attractive procedure for the biological control of the exposition to hazardous solvents. This kind of analysis presents numerous advantages over other methods, the most important being that it is not an invasive procedure and, therefore, it is well accepted and can be applied to a wide range of compounds. Furthermore, the analysis is simplified since the matrix is less complex that in the case of blood or urine. In spite of these obvious advantages and the good results obtained, analysis of exhaled air is not in daily use, probably due to the fact that there are no normalized systems of sampling, thus making the interpretation of the results difficult. In this paper, a method for the determination of tetrachloroethylene in exhaled air using solid-phase microextraction is presented. This method, which can be applied to other volatile organic compounds, was developed with special emphasis of end-exhaled breath sampling. The sample is collected in a glass tube whose ends are closed once the exhalation is finished. The tube has an orifice sealed with a septum through which the fiber is inserted. Then, the fiber is desorbed in the injector of a gas chromatograph and the analysis is accomplished using mass spectrometry for the identification and quantification of the components. The proposed system avoids the need of complex sampling equipment and allows analysis of the alveolar fraction. Additionally, the system is economical and easy to handle, thus facilitating the development of normalized methods and its routine use in field studies.     

Polymers for Enhanced Oil Recovery Technology

Recently enhance oil recovery (EOR) technology is getting more attention by many countries since energy crises are getting worse and frightened. One of the reasons for this is due to the shortage of current oil resources and difficulties in finding a new oil field. Indonesia is one of the examples, before 2004 Indonesia is a net oil exporting country but after that Indonesia is a net oil importing country. The oil demand in the country is increasing while the oil production capacity is decreasing. In fact, when a new oil reservoir is drilled, the oil amount obtained from it is about 20-40% of the potential and hence there is still 60-80% oil left in the reservoir. Application of EOR technology gives an additional chance to get out more oil from the reservoir, possibly about another 20%. Polymer is the material that plays an important role in the application of EOR technology, especially surfactant and hydrogel polymers. In the technology, surfactant polymer is injected to the reservoir to reduce an interfacial tension between oil and water and is able to wipe out the trapped oil from the reservoir rock and hence increase the oil production. While an injection of hydrogel polymer to the reservoir is to increase a viscosity of fluid containing water so that the fluid is more difficult to flow than the oil, and as a result, the oil production increases. The most common polymer used for this application is polyacrylamide group.     

Simulation and analysis of free radical branching copolymerization kinetics

Iｔｉｓｄｉｆｆｉｃｕｌｔａｎｄｅｖｅｎｉｍｐｏｓｓｉｂｌｅｔｏｄｅｔｅｒｍｉｎｅｂｙｒｅｇｕｌａｒｋｉｎｅｔｉｃｓｍｅｔｈｏｄｓｓｏｍｅｋｉｎｅｔｉｃｓｐａｒａｍｅｔｅｒｓｏｆｓｏｍｅｃｏｍｐｌｅｘｃｈｅｍｉｃａｌｒｅａｃｔｉｏｎｓ,ｅｓｐｅｃｉａｌｌｙｐｏｌｙｍｅｒｉｚａｔｉｏｎｒｅａｃｔｉｏｎｓｗｈｏｓｅｍｅｃｈａｎｉｓｍｓｈａｖｅｎｏｔｂｅｅｎｋｎｏｗｎ.Ｗｅｈａｖｅｔｒｉｅｄｔｏｓｏｌｖｅｔｈｉｓｐｒｏｂｌｅｍｂｙｔｈｅｍｅｔｈｏｄｏｆｒｅｇｒｅｓｓｉｏｎａｎｄｓｉｍｕｌａｔｉｏｎｏｆｃ…     

Adsorption and structure of hydrocarbons in MCM-41: a computational study

The adsorption of linear, branched, and cyclic hydrocarbons in MCM-41 is studied using Configurational Bias Monte Carlo simulations. A new computational model for MCM-41 is proposed which, although simple, is able to predict adsorption isotherms which are in agreement with the scarce experimental data. The structure of the adsorbed phase is analyzed and found to be similar to that of studies using small, hard spheres trapped in pores. The adsorption of mixtures is investigated, and the adsorption hierarchy is discussed. The structure of the adsorbed mixture is revealed and shows that all components of the mixture exhibit structure, even if they are only adsorbed in small quantities. Finally, the model is modified to include surface roughness and the effect on the adsorption isotherms and structure of the adsorbed phase is discussed.     

响应面法优化巴旦木壳对废水Pb、Cu和Cd的吸附及同时测定

研究废弃巴旦木壳对模拟废水中Pb、Cu和Cd的去除率。在单因素试验的基础上,采用响应面法对吸附剂投加量、吸附时间和pH值3因素进行优化。实验结果表明,最佳吸附条件为Pb：为吸附剂投加量0.4g、吸附时间49.38min、pH值为9.96;Cu：吸附剂投加量0.4g、吸附时间49.91min、pH值为10.13;Cd：吸附剂投加量0.4g、吸附时间49.83min、pH值为10.42;在此条件下,Pb、Cu和Cd的去除率分别为87.42%、73.49%和85.11%。采用偏最小二乘法(PLS)对Pb、Cu和Cd模拟混合试样吸附后的溶液进行同时测定,计算得出吸附剂对Pb、Cu和Cd的去除率分别为83.2%、66.0%和83.3%。     

Full enzymatic hydrolysis of commercial sucrose laurate by immobilized-stabilized derivatives of lipase from Thermomyces lanuginosa

Sucrose laurate is a detergent that is useful for various biochemical applications because it is a green compound and is easily degradable after hydrolysis with a lipase or esterase. One problem observed in the process of sucrose laurate degradation is that most commercial detergent preparations are impure, necessitating the hydrolysis of all of the sucrose esters present in the preparation, all of them with detergent properties. In this article, a highly active catalyst, which is able to perform the hydrolysis of commercial sucrose laurate, is presented. The use of glyoxyl agarose preparations of a previously aminated Thermomyces lanuginosa lipase (TLL) enabled complete hydrolysis, in less than 30 min, of all of the compounds that comprise the mixture. In addition, this derivative is stable in the presence of 20% ethanol, which is necessary to prevent microbial contamination.     

酸碱软硬度的电势原子势标度

软硬酸碱原则在化学的各个领域都得到了广泛的应用。在其定量化标度方面也做了不少工作,例如Yingst等的酸度量|α/β|,Klopman的E_n~≠和E_m~≠值,parr和pearson的绝对硬度以及Yatsimirski的ΔA_(FH)等。但是,他们的工作在理论性和应用上都无法统一起来。本文提出一种具有广泛应用性的酸碱软硬度的键参数标度。Mulliken在研究一类弱lewis加合物的光谱时,首先用量子力学原理阐述了lewis