Extraction of arsenic species from spiked soils and standard reference materials

The abilities of various extractants to recover four arsenic species [As(iii), As(v), dimethylarsinic acid (DMA), and monomethylarsonic acid (MMA)] from soils spiked with 20 micro g g(-1) As were investigated. The extractants were water, buffer solutions (citrate and ammonium dihydrogen phosphate), acidic solutions (phosphoric acid and acetic acid), a basic solution (sodium hydroxide) and household chemicals (vinegar and Coca Cola). Gentle shaking at room temperature with each extractant for 24 h gave different recoveries for the different arsenic species. With 0.1 M NaOH solution 46% As(iii), 53% DMA, 100% MMA and 84% As(v) were recovered. A rapid extraction procedure using a sonicator probe has been developed to obtain higher extraction efficiencies. Extracts of arsenic-spiked soil, SRM 2711 Montana soil and SRM 2709 San Joaquin soil were analyzed by HPLC-ICP-MS. In the SRM water extracts, DMA and MMA were identified in addition to inorganic arsenic. The solution detection limits (3s) were 0.1, 0.12, 0.13 and 0.15 ng mL(-1) for As(iii), DMA, MMA and As(v), respectively for HPLC-ICP-MS.     

Evaluation of non-chromatographic approaches for speciation of extractable As(III) and As(V) in environmental solid samples by FI-HGAAS

Non-chromatographic speciation approaches have been developed for determination of water-soluble and phosphate-exchangeable As(III) and As(V) in certified reference materials of coal fly ash and sediments by FI-HGAAS. A 2_IV^6-2 fractional factorial design was employed for screening optimisation of the flow injection manifold. A simple two-stage sequential extraction protocol involving deionized water and a phosphate buffer as extractants was employed. Determination of both oxidation states of As in the extracts could be accomplished following arsine generation under different reaction conditions, namely, (i) selective determination of As(III) in citric acid medium or using soft generation conditions (i.e. low HCl and NaBH₄ concentrations); (ii) determination of total As in each extract using thioglycollic acid as reaction medium or after pre-reduction of As(V) to As(III) with a KI+ascorbic acid mixture. The As(V) content was estimated by difference between both measurements. Reaction conditions were previously optimised and analytical parameters in each reaction medium were established. Overall, the extractable As content was less than 5% in sediment and fly ash CRMs. The LOD of As was around 0.07 μg l⁻¹ for As(III) determination, and 0.06 μg l⁻¹ for total As determination after prereduction. Liquid chromatography coupled to atomic fluorescence spectrometry with post-column hydride generation was used for comparison.     

Fractionation and redox speciation of antimony in agricultural soils by hydride generation--atomic fluorescence spectrometry and stability of Sb(III) and Sb(V) during extraction with different extractant solutions

This stability of Sb(III) and Sb(V) species was studied during single extraction from soils by water. EDTA, diluted H2SO4 and H3PO4, and oxalic acid/oxalate solutions, with and without ascorbic acid, were used as stabilizing reagent of both Sb species. Antimony redox speciation in soil extracts was performed by selective hydride generation-atomic fluorescence spectrometry. Simulated extraction procedures (without soil) showed that, except in oxalate medium, Sb(III) was oxidized to Sb(V), and this reaction was avoided with ascorbic acid. Recovery studies from a spiked agricultural soil showed that no oxidation but sorption of Sb(III) occurred during the extraction process in water and H2SO4 medium, and quantitative oxidation in EDTA and oxalate medium. With ascorbic acid, this oxidation was totally avoided in EDTA and partially avoided in oxalate solution. A new sequential extraction procedure was proposed and applied to the fractionation and redox speciation of antimony in agricultural soils, using EDTA + ascorbic acid, pH 7 (available under complexing and moderately reducible conditions); oxalic acid/oxalate + ascorbic acid (extractable in reducible conditions) and HNO3 + HCl + HF (residual fraction). The proposed extraction scheme can provide information about the availability and mobility of antimony redox species in agricultural soils.     

A systematic study on extraction of total arsenic from down-scaled sample sizes of plant tissues and implications for arsenic species analysis

An easily feasible, species-conserving and inexpensive protocol for the extraction of total arsenic and arsenic species from terrestrial plants was designed and applied to the investigation of accumulation and metabolization of arsenite (As(III)), arsenate (As(V)), monomethylarsonate (MMA(V)), and dimethylarsinate (DMA(V)) by the model plant Tropaeolum majus. In contrast to existing extraction methods hazardous additives and elaborate procedures to enhance the extraction yields were omitted. The proposed protocol is suited to down-scale the sample sizes used for the extractions and to promote a compartmentally resolved analysis of the arsenic distribution within individual leaves, leaf stalks, and stems instead of the conventional extraction of pooled samples. In a two-step extraction, the high extraction efficiencies (85-92%) for arsenic achieved by phosphate buffer from larger amounts (200mg) of homogenized leaf material in a one-step extraction, could be enhanced to 94-100% in a second extraction step. A strong dependence of the arsenic extractability on the type of arsenic species accumulated in the tissue as well as on the type of the tissue (leaf, leaf stalk, stem) was found. For the extraction of 5mm long segments cut from individual leaves without previous homogenization of the plant parts yields between 75 and 93% depending on arsenic species prevailing in the cells were obtained using 1 or 10mM phosphate buffer. The total extraction and analysis protocol was validated using a standard reference material as well as by spiking experiments. The arsenic species analysis by IC/ICPMS revealed a number of nine unidentified metabolites in the plant extracts in addition to the species MMA(V), DMA(V), As(III), and As(V) that were provided to the plants during their growth phase.     

Extraction equilibria of rare earths by a new reagent (2-ethylhexyl-3-pentadecylphenyl) phosphoric acid

A new reagent (2-ethylhexyl-3-pentadecylphenyl) phosphoric acid (EPPA = HR) was synthesized from cardanol (I, 37300-39-5) and was used to investigate the extraction behaviour of lanthanum(III), europium(III) and lutetium(III) from hydrochloric acid solutions. The species extracted were found to be Ln(HR(2))(3) (where Ln = La(III) or Eu(III) or Lu(III)). The extraction behaviour of the above lanthanides has also been compared with yttrium and other rare earths. It was observed that the extraction increases with increase in atomic number of rare earths. In addition, the extraction efficiency of EPPA has also been compared with well known acidic organophosphorus extractants like di-2-ethylhexyl phosphoric acid (DEHPA), 2-ethylhexyl-mono-2-ethylhexyl phosphoric acid (EHEHPA).     

Extraction and speciation of arsenic in plants grown on arsenic contaminated soils

A sequential arsenic extraction method was developed that yielded extraction efficiencies (EE) that were approximately double those using current methods for terrestrial plants. The method was applied to plants from two arsenic contaminated sites and showed potential for risk assessment studies. In the method, plants were extracted first by 1:1 water-methanol followed by 0.1 M hydrochloric (HCl) acid. Total arsenic in plant and soil samples collected from contaminated sites was mineralized by acid digestion and detected by inductively coupled plasma-atomic emission spectrometry (ICP-AES) and hydride generation-atomic absorption spectrometry (HG-AAS). Arsenic speciation was done by high performance liquid chromatography coupled with HG-AAS (HPLC-HGAAS) and by HPLC coupled with ICP-mass spectrometry (HPLC-ICP-MS). Spike recovery experiments with arsenite (As(III)), arsenate (As(V)), methylarsonic acid (MA) and dimethylarsinic acid (DMA) showed stability of the species in the extraction processes. Speciation analysis by X-ray absorption near edge spectroscopy (XANES) demonstrated that no transformation of As(III) and As(V) occurred due to sample handling. Dilute HCl was efficient in extracting arsenic from plants; however, extraction and determination of organic species were difficult in this medium. Sequential extraction with 1:1 water-methanol followed by 0.1 M-HCl was most useful in extracting and speciating both organic and inorganic arsenic from plants. Trace amounts of MA and DMA in plants could be detected by HPLC-HGAAS aided by the process of separation and preconcentration of the sequential extraction method. Both organic and inorganic arsenic compounds could be detected simultaneously in synthetic gastric fluid extracts (GFE) but EEs by this method were lower than those of the sequential method. The developed sequential method was shown to be reliable and applicable to various terrestrial plants for arsenic extraction and speciation.     

Arsenic speciation in contaminated soils

A method for arsenic speciation in soils is developed, based on extraction with a mixture of 1 mol l(-1) of phosphoric acid and 0.1 mol l(-1) of ascorbic acid, and further measurement with the coupling liquid chromatography (LC)-ultraviolet (UV) irradiation-hydride generation (HG)-inductively coupled plasma mass spectrometry (ICP/MS). The stability of the arsenic species in the extracts is also studied. The speciation method applied to several Spanish agricultural contaminated soils from the Aznalcollar zone shows that arsenate is the main species in all the soils analysed and that in some samples arsenite and methylated species could also be detected. The determination of the "pseudototal" arsenic in these soils, obtained by applying extraction with aqua regia (ISO Standard 11466), is also carried out. Both the speciation method and the aqua regia method are applied to several certified reference materials (CRMs) in which total arsenic content is certified. Finally, the same LC-UV-HG coupling with atomic fluorescence spectrometry (AFS) detection reveals to be a valid coupling system to perform arsenic speciation in the soils according to its fair quality parameters and easy utilisation.     

A gradient anion exchange chromatographic method for the speciation of arsenic in lobster tissue extracts

A gradient anion exchange chromatographic technique was developed for the separation of arsenobetaine (AsB), arsenocholine (AsC), arsenite (As(III)), arsenate (As(V)), monomethylarsonic acid (MMAA) and dimethylarsinic acid (DMAA) in one chromatographic run. This technique used low residue ammonium carbonate buffer and the inductively coupled plasma-mass spectrometry (ICP-MS) chromatograms showed little baseline drift. Gradient elution improved peak shape and peak separation. The separation was completed in approximately 27 min with low detection limits (0.017-0.029 mug As kg(-1)). Baseline resolution of all the arsenic species evaluated was achieved when the concentration of AsC was less than approximately 12.5 mug As kg(-1). This technique was successfully applied to different extracts of a standard reference material, TORT-2, and lobster tissue. AsB was found to be the major arsenic species present. AsC, DMAA, MMAA and As(V) were also found, although MMAA was not detected in all of the TORT-2 extracts. Two unknown peaks found may be due to the presence of arsenosugars or other arsenic species. Discrepancy between extraction recoveries previously determined using flow injection-ICP-MS and the high-performance liquid chromatography-ICP-MS was observed in some cases. The differences may be due to the extraction technique and/or conditions at which the extractions were performed.     

Synergistic solvent extraction of Eu, Sr and Cs into chlorobenzene solutions of the three conformers of tetrathiocalixarene and dicarbollide

Solvent extraction of several long-lived fission products from diluted nitric acid in pronounced synergistic systems involving dicarbollide and conformers of a specific thiacalix[n]arene were investigated using mainly chlorobenzene as the diluent. The following factors were experimentally investigated: molar ratio of the two extractants, total extractants concentration, aqueous acidity, nature of the mineral acid used, relative phase volumes, repeated extractions and metal concentration. Data are given on the rather slow kinetics of extraction and stripping, limited chemical stability of the extractants, selectivity and interference of foreign metals. The three different conformers of the basic compound with identical chemical composition exhibit very differing extraction properties. The plots of distribution ratios of all metals tested versus the varying concentration of one extractant keeping the concentration of the other extractant constant invariably exhibit maxima, interpreted as the result of an existence of several extracted species in the extract. Suggestions are given concerning possible practical applications of two of the conformers studied.     

CZE for the speciation of arsenic in aqueous soil extracts

We developed two separation methods using CZE with UV detection for the determination of the most common inorganic and methylated arsenic species and some phenylarsenic compounds. Based on the separation method for anions using hydrodynamic sample injection the detection limits were 0.52, 0.25, 0.27, 0.12, 0.37, 0.6, 0.6, 1.2 and 1.0 mg As/L for phenylarsine oxide (PAO), p-aminophenylarsonic acid (p-APAA), o-aminophenylarsonic (o-APAA), phenylarsonic acid (PAA), 4-hydroxy-3-nitrobenzenearsonic acid (roxarsone), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), arsenite or arsenious acid (As(III)) and arsenate (As(V)), respectively. These detection limits were improved by large-volume sample stacking with polarity switching to 32, 28, 14, 42, 22, 27, 26 and 27 microg As/L for p-APAA, o-APAA, PAA, roxarsone, MMA, DMA, As(III) and As(V), respectively. We have applied both methods to the analysis of the arsenic species distribution in aqueous soil extracts. The identification of the arsenic species was validated by means of both standard addition and comparison with standard UV spectra. The comparison of the arsenic species concentrations in the extracts determined by CZE with the total arsenic concentrations measured by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) indicated that CZE is suited for the speciation of arsenic in environmental samples with a high arsenic content. The extraction yield of phenylarsenic compounds from soil was derived from the arsenic concentrations of the aqueous soil extracts and the total arsenic content of the soil determined by ICP-AES after microwave digestion. We found that 6-32% of the total amount of arsenic in the soil was extractable by a one-step extraction with water in dependence on the type of arsenic species.     

有机磷酸混合萃取体系的界面化学及动力学控制机制研究

研究了D2EHPA(二(2-乙基己基)磷酸)-M₁PA、M₂PA(长碳链单烷基磷酸酯)-Al³⁺和D2EHPA-MEHPA(单(2-乙基己基)磷酸)-Al³⁺混合萃取体系的界面化学和动力学。结果表明,混合体系界面活性下降,D2EHPA-M₁PA萃取Al³⁺的过程为扩散和化学反应共同控制机制。     

Speciation of antimony in airborne particulate matter using ultrasound probe fast extraction and analysis by HPLC-HG-AFS

A fast extraction procedure has been developed for Sb(III) and Sb(V) oxoanions speciation in airborne particulate matter samples. Different extraction media (diammonium tartrate, hidroxilammonium clorhidrate, citric acid + ascorbic acid, phosphoric acid and citrate solutions) were tried, with assistance of an ultrasonic probe. The operation power and time of extraction were also optimized. The higher extraction recoveries were obtained with a 100 mmol L⁻¹ hidroxilammonium clorhidrate aqueous solution assisted by the ultrasound probe operated at 50 W during 3 min. The extracts were analyzed by HPLC-HG-AFS. The chromatographic separation of Sb(III) and Sb(V) was also optimized using diammonium tartrate and phthalic acid as mobile phases. The separation of both Sb species was performed in less than 3 min under isocratic conditions, using a 200 mmol L⁻¹ diammonium tartrate solution. The proposed extraction procedure and the HPLC-HG-AFS instrumental coupling have been successfully applied to airborne particulate matter samples, with high Sb content, collected in heavy traffic streets from Buenos Aires (Argentina). The results showed the presence of both Sb species at similar concentrations in the ng m⁻³ level. The extraction yield was higher than 90% for all the analyzed samples.     

Extraction of complexes of iron(III) and other metals with bis(2-ethylhexyl)phosphoric acid into molten biphenyl/naphthalene

The extraction behaviour of twelve metals as function of the concentration of nitric or hydrochloric acid is described; bis(2-ethylhexyl)phosphoric acid (BEHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester are used as the extractants with 3:1 (w/w) biphenyl/ naphthalene (m.p. 52°C) as the molten solvent which is easily separated by cooling to room temperature. Scandium (III) and zirconium (IV) can be separated from uranium (VI), rare earth metals and some transition metals with BEHPA. The extraction behaviour of iron with both extractants is described in detail.     

Multiple proton ionizable calixarene derivatives with different ring sizes and complexation ability as efficient ionophores for complexation and solvent extraction of trivalent indium

The solvent extraction behavior of multiple proton ionizable p-tert-butylcalix[4]arene and [6]arene carboxylic acid derivatives towards indium has been investigated along with an acyclic monomeric analogue from weakly acidic media into chloroform. The extraction mechanism is ion exchange and carboxylic acid groups are adequate ligating sites for extraction. The cyclic structure of calixarene ligands to accommodate the potential guest species and the cooperativity effect of multifunctional groups significantly affect the complexation behavior and calixarene derivatives are found to be excellent extractants over the monomeric analogue. The composition of the extracted complex depends on the solution pH and attempts to determine the composition of the extracted complex for the extraction of indium have been stymied by complications arising from the formation of polynuclear species of indium and bridged polymeric species of calixarene carboxylic acid derivatives. One mole of calix[4]arene derivative extracts 2.5 moles of indium whereas the calix[6]arene derivative tends to extract 4.0 moles of indium. The loaded indium is back extracted with 1 mol dm(-3) hydrochloric acid solution. Though quantitative back extraction of indium was achieved from the fully loaded calix[6]arene derivative, it was only achieved up to 85% in the case of the calix[4]arene derivative.     

A study of radiation effects on the extraction of americium(III) with acidic organophosphates

Radiation effects on the extraction of americium(III) with several dialkylphosphoric and monoalkylphosphoric acids have been studied comparatively. The extractants were exposed to⁶⁰Co γ-rays in the absence and presence of diluent and HNO₃. The Df of Am(III) was measured and the yield of radiolytic products was determined after γ-irradiation as a function of the absorbed dose. Di(hexoxyethyl)phosphoric acid was the most susceptible to radiation among the extractants studied and its extractability was weakened by radiation regardless of the presence or absence of diluent or HNO₃. Diisodecylphosphoric acid itself showed an enhancement upon irradiation but incurred a depressant effect upon intimate contact with HNO₃·Mono(2-ethylhexyl)phosphoric acid showed a decrease of the Df of Am(III), similarly to DIDPA in the presence of HNO₃ during γ-irradiation. All the above extractants gave H₃PO₄ as the principal radiolytic product upon γ-irradiation upon intimate contact with HNO₃ causing decreasing solely the extraction of Am(III). Di(2-ethylhexyl)phosphoric acid proved to be the most stable extractant to radiation among those studied.     

二-（2-乙基己基）磷酸P204与三烷基叔胺N235协同萃取钼

研究了P204（二-(2-乙基己基)磷酸, HA）和N235（三烷基胺, R3N）二元体系在HCl介质中对金属钼的萃取,结果表明P204和N235混合萃取剂在萃取钼时存在协同效应,并且在N235摩尔分数为0.7时协萃系数为2.24;考察了溶液酸度、P204或N235浓度及温度对萃取钼的影响,确定了协萃络合物为(R3NH)3•HMo8O26•2(HA),并比较了负载前后有机相的红外光谱。     

Study of HDEHP-PAN solid extractants for the determination of <Superscript>90</Superscript>Sr

Solid extractants containing di-(2-ethylhexyl)phosphoric acid (HDEHP) in the support based on modified polyacrylonitrile (PAN) were studied for the determination of ⁹⁰Sr by means of measuring the activity of its separated ⁹⁰Y daughter. In this paper, ¹⁵²Eu and ¹³³Ba were used as chemical homologues of ⁹⁰Y and ⁹⁰Sr. For these radionuclides, dependences of mass distribution coefficients (D _g) on the nitric acid concentration were measured for several types of HDEHP-PAN solid extractants. The mechanism of the Eu³⁺ and Ba²⁺ ions extraction was confirmed to follow the theoretical two-phase equation for the chelating extractants. Further, the influences of the presence of nitrates, calcium and iron ions on the values of D _g(Ba, Eu) were determined concentrating on the possibility of masking the iron ions by the addition of the ascorbic acid. This method was tested on the solution simulating the leachate of ashed green plant sample. The results obtained make the application of solid extractants containing HDEHP in PAN support prospective for ⁹⁰Sr determination.     

Extraction and exchange behavior of metal species in therapeutically applied peat

The binding and availability of metals (Al, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb, Zn) in therapeutically applied peat (Grosses Gifhorner Moor, Sassenburg/North Germany) was characterized by means of a versatile extraction approach. Aqueous extracts of peat were obtained by a standardized batch equilibrium procedure using high-purity water (pH 4.5 and 5.0), 0.01 mol l(-1) calcium chloride solution, 0.01 mol l(-1) ethylenediaminetetraacetic acid (EDTA) and 0.01 mol l(-1) diethylenetriamine pentaacetic acid (DTPA) solution as metal extractants. In addition, the availability of peat-bound metal species was kinetically studied by collecting aliquots of extracts after different periods of extraction time (5, 10, 15, 30, 60 and 120 min). Metal determinations were performed by atomic spectrometry methods (AAS, ICP-OES) and dissolved organic matter (DOM) was characterized by UV/Vis measurements at 254 and 436 nm, respectively. Of the extractants studied Ca, Mg and Mn were the most available metals, in contrast to peat-bound Fe and Al. The relative standard deviation s(r) of the developed extraction procedures was mostly in the range of 4 to 20%, depending on the metal and its concentration in peat. A pH increase favored the extraction of metals and DOM from peat revealing complex extraction kinetics. Moreover, a competitive exchange between peat-bound metal species and added Cu(II) ions showed that >100 mg of Cu(II) per 50 g wet peat was necessary to exchange the maximum of bound metals (e.g. 21.8% of Al, 3.9% of Fe, 79.0% of Mn, 81.9% of Sr, related to their total content).     

皂化P204/煤油微乳体系分离L-苯丙氨酸的研究

研究了P204-煤油-NaOH组成的微乳液膜配方及其稳定性。通过该液膜体系对L-苯丙氨酸水溶液进行提取实验,考察了P204的浓度、乳水比、外水相pH值、膜相重复使用次数、分离时间等对提取效率的影响。实验结果表明,微乳液膜不仅稳定性好,无明显溶胀和泄漏,分离速度快,而且分离效果好,可自动破乳,油相可重复多次使用,对L-苯丙氨酸的一次性提取率达88.25%。     

A systematic study on the extractability of arsenic species from algal certified reference material IAEA-140/TM (Fucus sp., Sea Plant Homogenate) using methanol/water extractant mixtures

Using methanol/water mixtures (from pure water to pure methanol), with different desorption and solubility parameters, and varying extractant volume to algal mass (V/m) ratios, the extractability of arsenic species from CRM IAEA-140/TM was investigated. A linear sorption isotherm-based model was developed to process the data obtained with variable volume extraction, allowing the unambiguous deduction of the maximal extractable species concentrations under the specific extraction conditions, even for more stable species.The maximal extractable arsenic fraction ranged from 41 to 68% of the total arsenic concentration in CRM IAEA-140/TM, depending on the extractant composition, with pure methanol giving the lowest extraction yield and pure water giving erratic extractability (probably due to bad wettability). The main arsenic species quantified in the methanol/water extracts were arsenosugars, with arsenosugars 1 (glycerol arsenosugar), 3 (sulfonate arsenosugar) and 4 (sulfate arsenosugar) making up ca. 90% of the maximal extractable arsenic. The rest accounts for DMA (dimethylarsinate), arsenosugar 2 (phosphate arsenosugar) and As(V). There is no clear extraction pattern emerging from the data although it may be seen that extraction of more polar species (e.g. arsenosugar 1) is favoured in pure methanol and less polar more ionic species (e.g. arsenosugar 2 and As(V)) in methanol extractants with a higher water percentage.The precise and highly accurate data may be used for quality control purposes under strictly followed extraction conditions since the extraction is operationally defined. Additionally, the variable volume extraction methodology presented may be applied to other elemental species in other matrices using other extractants. Although this approach does not maximise the absolute extractability but only that which is extractant-specific, experimentators are forewarned that in most cases only a fingerprint of the extractant-specific species is produced unless a quantitative extraction of all species is obtained.