Transient and steady-state behavior of auto-igniting propane and dimethyl ether fuel jets in high-temperature vitiated coflows

In the current study, the auto-ignition dynamics of cold fuel jets issuing into a high-temperature, vitiated environments is investigated. Due to the short time scale of these events, high-speed measurements are used to resolve the coupled spatio-temporal behavior. The present study uses high-speed (20-kHz) OH* chemiluminescence imaging to identify the location and timing of the formation of the initial ignition kernels, providing visualization of the ignition dynamics and a detailed statistical evaluation of ignition heights and ignition delay times across a broad parameter space which includes variations in fuel type, dilution levels, coflow temperature, and coflow oxidizer content. The auto-ignition location and ignition delay times show a strong sensitivity to coflow temperature with increased sensitivities at lower coflow temperatures. Comparisons between kernel formation location for the transient jet and the fluctuating flame base of the subsequent, steady-state flame is presented, highlighting the role of flame propagation on flame stabilization. Results indicate that at lower temperatures the flame stabilization mechanism is dominated by auto-ignition, but at higher coflow temperatures, flame propagation plays a key role. The effects of variations in the hot, coflow oxidizer content on ignition properties were found to be noticeable, but still significantly less than variations in the temperature.     

Simultaneous rainbow schlieren deflectometry and OH* chemiluminescence imaging of a diesel spray flame in constant pressure flow rig

The physical and chemical phenomena that take place during fuel injection, entrainment and fuel-air mixing, cool-flame and ignition reaction, and combustion in diesel sprays still require extensive study. Global parameters such as liquid and vapor jet penetration lengths and spreading rates render useful yet still limited information. Understanding of the temporal evolution of the spray as it progresses through various steps is needed to develop advanced clean combustion modes and high-fidelity predictive models with sufficient accuracy. In this study, high-speed rainbow schlieren deflectometry (RSD) and OH* chemiluminescence are used to simultaneously image fuel-air mixing, cool-flame reactions, ignition, flame propagation and stabilization, and combustion in a transient diesel-like flame. A constant pressure flow rig (CPFR) is used to conduct multiple injections in quick succession to obtain a statistically relevant dataset. n-heptane was injected at nominal supply pressure of 1000 bar from a single-hole diesel injector into ambient at pressure of 30 bar and temperature of 800 K. About 500 injections were performed and analyzed to reveal structural features of non-reacting and reacting regions of the spray, quantify jet penetration and spreading rates, and study cool-flame behavior, ignition, flame propagation and stabilization at lift-off length, and combustion at upstream and downstream locations.     

Optical diagnostics on the reactivity controlled compression ignition (RCCI) with micro direct-injection strategy

Micro direct-injection (DI) strategy is often used to extend the operation range of the reactivity controlled compression ignition (RCCI) to high engine load, but its combustion process has not been well understood. In this study, the ignition and flame development of the micro-DI RCCI strategy were investigated on a light-duty optical engine using formaldehyde planar laser-induced fluorescence (PLIF) and high-speed natural flame luminosity imaging techniques. The premixed fuel was iso-octane and an oxygenated fuel of polyoxymethylene dimethyl ethers (PODE) was employed for DI. The fuel-air equivalence ratio of DI was kept at 0.09 and the premixed equivalence ratio was varied from 0 to 1. RCCI strategies with early and late DI timing at –25° and –5° crank angle after top dead center were studied, respectively. Results indicate that the early micro-DI RCCI features a single-stage high-temperature heat release (HTHR). The combustion in the low-reactivity region shows a combination of flame front propagation and auto-ignition. The late micro-DI RCCI presents a two-stage HTHR. The second-stage HTHR is owing to the combustion in the low-reactivity region that is dominated by flame front propagation when the premixed equivalence ratio approaches 1. For both early and late micro-DI RCCI, the intermediate-temperature heat release (ITHR) of iso-octane, indicated by formaldehyde, takes place in the low-reactivity region before the arrival of the flame front. This is quite different from the flame front propagation in spark-ignition (SI) engine that shows no ITHR in the unburned region. The DI fuel mass is a key factor that affects the combustion in the low-reactivity region. If the DI fuel mass is quite low, there is more possibility of flame front propagation; otherwise, sequential auto-ignition dominates. The emergence of the flame front propagation in micro-DI RCCI strategy reduces its combustion rate and peak pressure rise rate.     

Auto-ignition and flame stabilization of pulsed methane jets in a hot vitiated coflow studied with high-speed laser and imaging techniques

The auto-ignition of a pulsed methane jet issuing into a laminar coflow of hot exhaust products of a lean premixed hydrogen/air flat flame was examined using high-speed laser and optical measurement techniques with frame rates of 5 kHz or more. OH* chemiluminescence was used to determine the downstream location of the first auto-ignition kernel as well as the stabilization height of the steady-state lifted jet flame. OH planar laser-induced fluorescence (PLIF) was used to determine further details of the auto-ignition with a higher spatial resolution. Simultaneous imaging of broadband luminosity from a viewing angle perpendicular to the OH* chemiluminescence was applied, to three-dimensionally reconstruct the ignition kernel location in space and to determine whether the first occurrence of the kernel was within or beyond the PLIF laser sheet. The development and expansion of the jet was characterized by high-speed Schlieren imaging. Statistics have been compiled for both the ignition time as well as the downstream location of the first auto-ignition kernel and the stabilization height of the steady-state lifted jet flame. From the PLIF images it was found that auto-ignition tended to occur at the interface between bulges of the inflowing jet and the coflow. For steady-state conditions, auto-ignition kernels were observed frequently below the flame base, emphasizing that the lifted jet flame is stabilized by auto-ignition.     

Experimental observation of turbulent jet ignition of pre-chamber with scavenging system for carbon dioxide diluted mixtures

The exhaust gas recirculation (EGR) method can suppress knock and improve the thermal efficiency of engines. But it will also deteriorate the combustion stability and engine power. Turbulent jet ignition (TJI) is a reliable ignition resource for improving ignition stability and burning rate. However, the residual productions in the pre-chamber will worsen the performance of the TJI. To this end, a self-designed pre-chamber with a scavenging system has been proposed. In this study, the ignition process and flame propagation phenomena under different EGR dilution ratios for H₂/N₂/O₂ and CH₄/N₂/O₂ mixtures were conducted in a constant-volume combustion chamber. The results suggested that the increase in EGR dilution weakens the influence of cellular instability and causes buoyancy instability, the latter of which could be mitigated by the passive TJI method. For the passive TJI mode, the exit time of the hot jet was delayed, and the turbulent flame speed decreased with the increase of EGR dilution ratio. Four ignition phenomena, namely jet re-ignition, flame buoyancy, re-ignition failure, and misfire, were distinctly identified. However, EGR tolerance cannot be extended by passive pre-chambers. Therefore, the pre-chamber with a scavenging system that can effectively extend the lean combustion tolerance with EGR dilution compared to SI and passive TJI was proposed. The effects of air and fuel injection quantities on ignition and flame propagation were investigated. The flame propagation velocity was positively related to the air injection mass, whereas an optimum fuel mass was required to achieve fast flame propagation. The EGR limit based on dual injections in the pre-chamber was obviously extended. Moreover, under near EGR tolerance conditions, a leaner fuel injection in the pre-chamber was required to realize successful ignition in the main chamber, as strong turbulence could cause high heat transfer loss with the cool unburnt mixture and suppress the occurrence of re-ignition.     

An experimental investigation on spray, ignition and combustion characteristics of biodiesels

Spray, ignition and combustion characteristics of biodiesel fuels were investigated under a simulated diesel-engine condition (885 K, 4 MPa) in a constant volume combustion vessel. Two biodiesel fuels originated from palm oil and used cooking oil were used while JIS#2 used as the base fuel. Spray images were taken by a high speed video camera by using Mie-scattering method to measure liquid phase penetration and liquid length. An image intensifier combined with OH filter was used to obtain OH radical image near 313 nm. Ignition and combustion characteristics were studied by OH radical images. Biodiesel fuels give appreciably longer liquid lengths and shorter ignition delays. At low injection pressure (100 MPa), biodiesel fuels give shorter lift-off lengths than those of diesel. While at high injection pressure (200 MPa), the lift-off length of biodiesel fuel originated palm oil gives the shortest value and that of biodiesel from used cooking oil gives the longest one. Air entrainment upstream of lift-off length of three fuels was estimated and compared to soot formation distance. This study reveals that the viscosity and ignition quality of biodiesel fuel have great influences on jet flame structure and soot formation tendency.     

A comparative study on partially premixed combustion (PPC) and reactivity controlled compression ignition (RCCI) in an optical engine

Partially premixed combustion (PPC) and reactivity controlled compression ignition (RCCI) are two new combustion modes in compression-ignition (CI) engines. However, the detailed in-cylinder ignition and flame development process in these two CI modes were not clearly understood. In the present study, firstly, the fuel stratification, ignition and flame development in PPC and RCCI were comparatively studied on a light-duty optical engine using multiple optical diagnostic techniques. The overall fuel reactivity (PRF number) and concentration (fuel-air equivalence ratio) were kept at 70 and 0.77 for both modes, respectively. Iso-octane and n-heptane were separately used in the port-injection (PI) and direct-injection (DI) for RCCI, while PRF70 fuel was introduced through direct-injection (DI) for PPC. The DI timing for both modes was fixed at –25°CA ATDC. Secondly, the combustion characteristics of PPC and RCCI with more premixed charge were explored by increasing the PI mass fraction for RCCI and using the split DI strategy for PPC. In the first part, results show that RCCI has shorter ignition delay than PPC due to the fuel reactivity stratification. The natural flame luminosity, formaldehyde and OH PLIF images prove that the flame front propagation in the early stage of PPC can be seen, while there is no distinct flame front propagation in RCCI. In the second part, the higher premixed ratio results in more auto-ignition sites and faster combustion rate for PPC. However, the higher premixed ratio reduces the combustion rate in RCCI mode and the flame front propagation can be clearly seen, the flame speed of which is similar to that in spark ignition engines but lower than that in PPC. It can be concluded that the ratio of flame front propagation and auto-ignition in RCCI and PPC can be modulated by the control over the fuel stratification degree through different fuel-injection strategies.     

Large eddy simulation of the low temperature ignition and combustion processes on spray flame with the linear eddy model

Large eddy simulation coupled with the linear eddy model (LEM) is employed for the simulation of n-heptane spray flames to investigate the low temperature ignition and combustion process in a constant-volume combustion vessel under diesel-engine relevant conditions. Parametric studies are performed to give a comprehensive understanding of the ignition processes. The non-reacting case is firstly carried out to validate the present model by comparing the predicted results with the experimental data from the Engine Combustion Network (ECN). Good agreements are observed in terms of liquid and vapour penetration length, as well as the mixture fraction distributions at different times and different axial locations. For the reacting cases, the flame index was introduced to distinguish between the premixed and non-premixed combustion. A reaction region (RR) parameter is used to investigate the ignition and combustion characteristics, and to distinguish the different combustion stages. Results show that the two-stage combustion process can be identified in spray flames, and different ignition positions in the mixture fraction versus RR space are well described at low and high initial ambient temperatures. At an initial condition of 850 K, the first-stage ignition is initiated at the fuel-lean region, followed by the reactions in fuel-rich regions. Then high-temperature reaction occurs mainly at the places with mixture concentration around stoichiometric mixture fraction. While at an initial temperature of 1000 K, the first-stage ignition occurs at the fuel-rich region first, then it moves towards fuel-richer region. Afterwards, the high-temperature reactions move back to the stoichiometric mixture fraction region. For all of the initial temperatures considered, high-temperature ignition kernels are initiated at the regions richer than stoichiometric mixture fraction. By increasing the initial ambient temperature, the high-temperature ignition kernels move towards richer mixture regions. And after the spray flames gets quasi-steady, most heat is released at the stoichiometric mixture fraction regions. In addition, combustion mode analysis based on key intermediate species illustrates three-mode combustion processes in diesel spray flames.     

1-庚烯/空气的高压层流火焰传播研究

本文使用定容圆柱形燃烧弹,在初始温度373 K和初始压力1、2、5、10 atm的条件下,对当量比从0.7到1.5的1-庚烯/空气混合物的层流火焰传播进行了研究.利用记录的纹影图像处理得到层流火焰传播速度和马克斯坦长度.基于先前报道的1-己烯燃烧反应动力学模型,发展了1-庚烯的模型.该模型验证了本工作测量的1-庚烯层流火焰传播速度数据及文献中的1-庚烯着火延迟时间数据.通过开展敏感性分析和路径分析,帮助理解了1-庚烯在不同压力下的高温化学及其对层流火焰传播的影响.另外,比较了1-庚烯/空气和先前报道的正庚烷/空气的层流火焰传播.由于更强的放热性及反应活性,1-庚烯/空气的层流火焰传播速度在绝大多数条件下均快于正庚烷/空气的结果.     

Simultaneous 36 kHz PLIF/chemiluminescence imaging of fuel,CH2O and combustion in a PPC engine

The requirements on high efficiency and low emissions of internal combustion engines (ICEs) raise the research focus on advanced combustion concepts, e.g., premixed-charge compression ignition (PCCI), partially premixed compression ignition (PPCI), reactivity controlled compression ignition (RCCI), partially premixed combustion (PPC), gasoline compression ignition (GCI) etc. In the present study, an optically accessible engine is operated in PPC mode, featuring compression ignition of a diluted, stratified charge of gasoline-like fuel injected directly into the cylinder. A high-speed, high-power burst-mode laser system in combination with a high-speed CMOS camera is employed for diagnostics of the autoignition process which is critical for the combustion phasing and efficiency of the engine. To the authors’ best knowledge, this work demonstrates for the first time the application of the burst-system for simultaneous fuel tracer planar laser induced fluorescence (PLIF) and chemiluminescence imaging in an optical engine, at 36?kHz repetition rate. In addition, high-speed formaldehyde PLIF and chemiluminescence imaging are employed for investigation of autoignition events with a high temporal resolution (5 frames/CAD). The development of autoignition together with fuel or CH₂O distribution are simultaneously visualized using a large number of consecutive images. Prior to the onset of combustion the majority of both fuel and CH₂O are located in the recirculation zone, where the first autoignition also occurs. The ability to record, in excess of 100 PLIF images, in a single cycle brings unique possibilities to follow the in-cylinder processes without the averaging effects caused by cycle-to-cycle variations.     

LES/CMC modelling of ignition and flame propagation in a non-premixed methane jet

The Large Eddy Simulation (LES) / Conditional Moment Closure (CMC) model with detailed chemistry is used for modelling spark ignition and flame propagation in a turbulent methane jet in ambient air. Two centerline and one off-axis ignition locations are simulated. We focus on predicting the flame kernel formation, flame edge propagation and stabilization. The current LES/CMC computations capture the three stages reasonably well compared to available experimental data. Regarding the formation of flame kernel, it is found that the convection dominates the propagation of its downstream edge. The simulated initial downstream and radial flame propagation compare well with OH-PLIF images from the experiment. Additionally, when the spark is deposited at off-centerline locations, the flame first propagates downstream and then back upstream from the other side of the stoichiometric iso-surface. At the leading edge location, the chemical source term is larger than others in magnitude, indicating its role in the flame propagation. The time evolution of flame edge position and the final lift-off height are compared with measurements and generally good agreement is observed. The conditional quantities at the stabilization point reflect a balance between chemistry and micro-mixing. This investigation, which focused on model validation for various stages of spark ignition of a turbulent lifted jet flame through comparison with measurements, demonstrates that turbulent edge flame propagation in non-premixed systems can be reasonably well captured by LES/CMC.     

Numerical simulation of a mixed-mode reaction front in a PPC engine

The ignition process, mode of combustion and reaction front propagation in a partially premixed combustion (PPC) engine running with a primary reference fuel (87% iso-octane, 13% n-heptane by volume) is studied numerically in a large eddy simulation. Different combustion modes, ignition front propagation, premixed flame and non-premixed flame, are observed simultaneously. Displacement speed of CO iso-surface propagation describes the transition of premixed auto-ignition to non-premixed flame. High temporal resolution optical data of CH₂O and chemiluminescence are compared with simulated results. A high speed ignition front is seen to expand through fuel-rich mixture and stabilize around stoichiometry in a non-premixed flame while lean premixed combustion occurs in the spray wake at a much slower pace. A good qualitative agreement of the distribution of chemiluminescence and CH₂O formation and destruction shows that the simulation approach sufficiently captures the driving physics of mixed-mode combustion in PPC engines. The study shows that the transition from auto-ignition to flame occurs over a period of several crank angles and the reaction front propagation can be captured using the described model.     

Ignition mechanisms of pulse detonator initiated scramjet cavity

A fueled cavity in a supersonic crossflow was ignited via a pulse detonator (PD) producing detonation waves that were then decoupled to produce varying degrees of shock-flame separation at the exit of the PD tube. This decoupling allowed for observation of the cavity ignition mechanism, and the key parameters required for successful cavity ignition were identified. Measurements were made using high-frame-rate OH Planar Laser-Induced Fluorescence (PLIF) and schlieren and chemiluminescence imaging. It was shown that the entrainment of high-temperature intermediate species into the forward region of the cavity, immediately behind the step, is the principal criterion for cavity ignition. Both coupled and slightly decoupled detonation cases induced significant OH shedding into the step region, leading to ignition and flame stabilization within the cavity. At conditions where OH shedding into the step region did not occur, cavity ignition was not observed. In coupled and slightly decoupled cases, there is more shedding of OH behind the step due to the greater disturbances created in the flowfield. As the degree of detonation decoupling increases, there is less shedding of OH and therefore a lower likelihood of ignition. Additionally, the time required for cavity combustion to reach its steady-state condition varied with the degree of decoupling of the detonation. Coupled detonation cases were shown to be more disruptive to the cavity and thus required more time to reach steady state than the decoupled cases.     

Dynamics of triple-flames in ignition of turbulent dual fuel mixture: A direct numerical simulation study

Pilot-ignited dual fuel combustion involves a complex transition between the pilot fuel autoignition and the premixed-like phase of combustion, which is challenging for experimental measurement and numerical modelling, and not sufficiently explored. To further understand the fundamentals of the dual fuel ignition processes, the transient ignition and subsequent flame development in a turbulent dimethyl ether (DME)/methane-air mixing layer under diesel engine-relevant conditions are studied by direct numerical simulations (DNS). Results indicate that combustion is initiated by a two-stage autoignition that involves both low-temperature and high-temperature chemistry. The first stage autoignition is initiated at the stoichiometric mixture, and then the ignition front propagates against the mixture fraction gradient into rich mixtures and eventually forms a diffusively-supported cool flame. The second stage ignition kernels are spatially distributed around the most reactive mixture fraction with a low scalar dissipation rate. Multiple triple flames are established and propagate along the stoichiometric mixture, which is proven to play an essential role in the flame developing process. The edge flames gradually get close to each other with their branches eventually connected. It is the leading lean premixed branch that initiates the steady propagating methane-air flame. The time required for the initiation of steady flame is substantially shorter than the autoignition delay time of the methane-air mixture under the same thermochemical condition. Temporal evolution of the displacement speed at the flame front is also investigated to clarify the propagation characteristics of the combustion waves. Cool flame and propagation of triple flames are also identified in this study, which are novel features of the pilot-ignited dual fuel combustion.     

Diesel flame lift-off stabilization in the presence of laser-ignition: a numerical study

Diesel flame lift-off and stabilization in the presence of laser-ignition were numerically investigated with the method of Eulerian stochastic fields. The aim was to scrutinise the interaction between the lifted diesel flame and an ignition kernel upstream of the lifted flame. The numerical simulation was carried out in a constant-volume combustion vessel with n-heptane as fuel. The process was studied previously in an experiment employing Diesel #2 as the fuel in the same combustion vessel. In the experiment a lifted flame was first established at a position downstream of the nozzle. An ignition kernel was then initiated using a high-energy pulse laser at a position upstream of the natural lift-off position of the diesel flame. The laser-ignition kernel was modelled using a high-temperature (～2000 K) hot spot. In both experiment and simulations the upstream front of the ignition kernel was shown to remain around the initial laser ignition site for a substantially long period of time, while the downstream front of the ignition kernel propagates rapidly towards the natural lift-off position downstream of the laser ignition site. The lift-off position oscillated before the final stabilization at the natural lift-off position. The structures and the propagation speed of the reaction fronts in the laser-ignition kernel and the main flame were analysed. Two different stabilization mechanisms, the auto-ignition mechanism and the flame propagation mechanism, were identified for the naturally lifted flame and the laser-induced reaction front, respectively. A mechanism was proposed to explain the oscillation of the lift-off position.     

Combination of schlieren and pulsed TV holography in the study of a high-speed flame jet

This paper presents studies of the propagation of a high-speed turbulent flame jet of an air/hydrogen gas mixture. The experimental results are recorded with the schlieren and the pulsed TV holography method. These methods are compared and combined to benefit from the advantages of each of them. Abel inversion has been used to achieve three-dimensional information i.e. refractive index distributions. Evaluation, calibration and Abel inversion algorithms are described together with experimental results. The results obtained from the different techniques show remarkable similarities concerning both qualitative and quantitative aspects.     

Experimental investigation of combustion instabilities of a mesoscale multinozzle array in a lean-premixed combustor

Self-excited combustion instabilities in a mesoscale multinozzle array, also referred to as a micromixer-type injector, have been experimentally investigated in a lean-premixed tunable combustor operating with preheated methane and air. The injector assembly consists of sixty identical swirl injectors of 6.5 mm inner diameter, which are evenly distributed across the combustor dump plane. Their flow paths are divided into two groups – inner and outer stages – to form radially stratified reactant stoichiometry for the control of self-excited instabilities. OH PLIF measurements of stable flames reveal that the presence of radial staging has a remarkable influence on stabilization mechanisms, reactant jet penetration/merging, and interactions between adjacent flame fronts. In an inner enrichment case, two outer (leaner) streams merge into a single jet structure, whereas the inner (richer) reactant jets penetrate far downstream without noticeable interactions between neighboring flames. The constructed stability map in the 〈?_i, ?_o〉 domain indicates that strong self-excited instabilities occur under even split and outer enrichment conditions at relatively high global equivalence ratios. This is attributed to large-scale flame surface deformation in the streamwise direction, as manifested by vigorous detachment/attachment movements. The use of the inner fuel staging method was found, however, to limit the growth of large-amplitude heat release rate fluctuations, because the center flames are securely anchored during the whole period of oscillation, giving rise to a moderate lateral motion. We demonstrate that the collective motion of sixty flames – rather than the individual local flame dynamics – play a central role in the development of limit cycle oscillations. This suggests that the distribution pattern of the injector array, in combination with the radial fuel staging scheme, is the key to the control of the instabilities.     

镁颗粒群着火和燃烧过程数值模拟

建立了一维非稳态球形镁颗粒群的着火燃烧模型, 数值模拟镁颗粒群的着火和燃烧过程, 研究表明, 颗粒群着火首先发生在颗粒群边界, 随后初始的燃烧火焰会分离为两个, 一个向颗粒群内部传播, 一个向外部传播, 最终内部火焰消失, 外部火焰维持并控制着整个颗粒群的燃烧; 内火焰向颗粒群内部传播过程中, 传播速度会逐渐加快, 且火焰温度值呈逐渐降低趋势. 分析了颗粒群内部参数和环境参数对镁颗粒群着火燃烧的影响. 随颗粒浓度的增大, 颗粒群着火时间略有增长, 但火焰传播速度更快, 燃烧稳定时火焰球尺寸也更大. 颗粒群初温越高, 则颗粒群着火时间越短, 火焰传播速度也会加快, 但燃烧稳定时火焰球尺寸基本不变. 环境温度对颗粒群着火燃烧的影响较复杂, 环境温度越高, 颗粒群着火时间越短, 但火焰传播速度却越慢, 燃烧稳定时火焰球尺寸变化很小. 颗粒粒径和辐射源温度对颗粒群着火燃烧的影响较显著, 颗粒粒径越小或辐射源温度越高, 则颗粒群着火时间越短, 火焰传播速度越快, 燃烧稳定时火焰球尺寸也越大. 数值模拟结果与文献中试验结果相一致. 关键词： 粉末燃料冲压发动机 镁着火燃烧 颗粒群     

Ignition of hexane-air mixtures by highly under-expanded hot jets

We report an experimental study of ignition of flammable mixtures by highly unexpanded, supersonic hot jets. The high-pressure, hot-gas reservoir supplying the jet is created by impacting a projectile on a plunger to rapidly compress and ignite a rich n-hexane/air mixture, resulting in a peak reservoir pressure of more than 20 MPa. A locking mechanism was used to prevent the plunger from rebounding and the jet was created by rupturing a diaphragm covering a nozzle with an exit diameter between 0.25 and 1 mm. The jet development and ignition processes in the main chamber filled with hexane-air mixture were visualized using high-speed schlieren and OH* chemiluminescence imaging. The ignition threshold was determined as a function of composition in the jet and main chamber, the nozzle diameter, and the initial pressure in the main chamber. Unlike the case of subsonic jets in which ignition occurs at the shear layer near the nozzle exit, ignition of combustion in the main chamber was found to take place downstream of the Mach disk terminating the supersonic expansion and within the turbulent mixing region created by the startup of the supersonic jet. The results are interpreted using a constant-pressure, well-stirred reactor model simulating the mixing between the hot jet and cold ambient gas. The critical conditions for ignition are determined by the competition between energy release due to chemical reactions initiated by the hot jet gas and cooling due to mixing with the cold chamber atmosphere. The critical value (maximum for which ignition occurs) of the mixing rate was computed using a detailed chemical reaction model and found to be a useful qualitative guide to our observations.