A comparative study on partially premixed combustion (PPC) and reactivity controlled compression ignition (RCCI) in an optical engine

Partially premixed combustion (PPC) and reactivity controlled compression ignition (RCCI) are two new combustion modes in compression-ignition (CI) engines. However, the detailed in-cylinder ignition and flame development process in these two CI modes were not clearly understood. In the present study, firstly, the fuel stratification, ignition and flame development in PPC and RCCI were comparatively studied on a light-duty optical engine using multiple optical diagnostic techniques. The overall fuel reactivity (PRF number) and concentration (fuel-air equivalence ratio) were kept at 70 and 0.77 for both modes, respectively. Iso-octane and n-heptane were separately used in the port-injection (PI) and direct-injection (DI) for RCCI, while PRF70 fuel was introduced through direct-injection (DI) for PPC. The DI timing for both modes was fixed at –25°CA ATDC. Secondly, the combustion characteristics of PPC and RCCI with more premixed charge were explored by increasing the PI mass fraction for RCCI and using the split DI strategy for PPC. In the first part, results show that RCCI has shorter ignition delay than PPC due to the fuel reactivity stratification. The natural flame luminosity, formaldehyde and OH PLIF images prove that the flame front propagation in the early stage of PPC can be seen, while there is no distinct flame front propagation in RCCI. In the second part, the higher premixed ratio results in more auto-ignition sites and faster combustion rate for PPC. However, the higher premixed ratio reduces the combustion rate in RCCI mode and the flame front propagation can be clearly seen, the flame speed of which is similar to that in spark ignition engines but lower than that in PPC. It can be concluded that the ratio of flame front propagation and auto-ignition in RCCI and PPC can be modulated by the control over the fuel stratification degree through different fuel-injection strategies.     

Numerical simulation of a mixed-mode reaction front in a PPC engine

The ignition process, mode of combustion and reaction front propagation in a partially premixed combustion (PPC) engine running with a primary reference fuel (87% iso-octane, 13% n-heptane by volume) is studied numerically in a large eddy simulation. Different combustion modes, ignition front propagation, premixed flame and non-premixed flame, are observed simultaneously. Displacement speed of CO iso-surface propagation describes the transition of premixed auto-ignition to non-premixed flame. High temporal resolution optical data of CH₂O and chemiluminescence are compared with simulated results. A high speed ignition front is seen to expand through fuel-rich mixture and stabilize around stoichiometry in a non-premixed flame while lean premixed combustion occurs in the spray wake at a much slower pace. A good qualitative agreement of the distribution of chemiluminescence and CH₂O formation and destruction shows that the simulation approach sufficiently captures the driving physics of mixed-mode combustion in PPC engines. The study shows that the transition from auto-ignition to flame occurs over a period of several crank angles and the reaction front propagation can be captured using the described model.     

Numerical simulation and validation of SI-CAI hybrid combustion in a CAI/HCCI gasoline engine

SI-CAI hybrid combustion, also known as spark-assisted compression ignition (SACI), is a promising concept to extend the operating range of CAI (Controlled Auto-Ignition) and achieve the smooth transition between spark ignition (SI) and CAI in the gasoline engine. In this study, a SI-CAI hybrid combustion model (HCM) has been constructed on the basis of the 3-Zones Extended Coherent Flame Model (ECFM3Z). An ignition model is included to initiate the ECFM3Z calculation and induce the flame propagation. In order to precisely depict the subsequent auto-ignition process of the unburned fuel and air mixture independently after the initiation of flame propagation, the tabulated chemistry concept is adopted to describe the auto-ignition chemistry. The methodology for extracting tabulated parameters from the chemical kinetics calculations is developed so that both cool flame reactions and main auto-ignition combustion can be well captured under a wider range of thermodynamic conditions. The SI-CAI hybrid combustion model (HCM) is then applied in the three-dimensional computational fluid dynamics (3-D CFD) engine simulation. The simulation results are compared with the experimental data obtained from a single cylinder VVA engine. The detailed analysis of the simulations demonstrates that the SI-CAI hybrid combustion process is characterised with the early flame propagation and subsequent multi-site auto-ignition around the main flame front, which is consistent with the optical results reported by other researchers. Besides, the systematic study of the in-cylinder condition reveals the influence mechanism of the early flame propagation on the subsequent auto-ignition.     

超声速预混可燃气流的点火与燃烧

在激波风洞一激波管组合设备上开展了碳氢燃料超声速预混可燃气流的点火与燃烧实验研究。实验结果表明:利用激波对燃料进行预热,并以高温燃气作为引导火焰,可以有效缩短汽油空气超声速可燃混气的点火延迟时间,使之缩短到 0.2 ms以下。利用纹影照片对超声速燃烧流场结构作出了分析;研究了超声速预混可燃气流的温度以及当量比对超声速燃烧流场结构、点火与火焰传播特性的影响。     

Characteristics of auto-ignition in a stratified iso-octane mixture with exhaust gases under homogeneous charge compression ignition conditions

Ignition and propagation of a reaction front in a counterflow system of an iso-octane/air stream mixing with an exhaust gas stream is computationally investigated to understand the fundamental characteristics of homogeneous charge compression ignition (HCCI) auto-ignition. Various mixing rates are imposed on the system and the effects of dissipation rates on auto-ignition are studied. Ignition delay and front propagation speed across the mixing layer are determined as a function of a local mixture fraction variable. The results show that mixture inhomogeneity and dissipation rate have a significant influence on ignition. Diffusive transport is found to either hamper or advance ignition depending on the initial reactivity of the mixture. Based on the relative importance of diffusion on ignition front propagation, two distinct ignition regimes are identified: the spontaneous ignition regime and the diffusion-controlled regime. The transition between these two regimes is identified using a criterion based on the ratio of the timescales of auto-ignition and diffusion. The results show that ignition in the spontaneous regime is more likely under typical HCCI operating conditions with iso-octane due to its high reactivity. The present analysis provides a means to develop an improved modelling strategy for large-scale engine simulations.     

Simultaneous 36 kHz PLIF/chemiluminescence imaging of fuel,CH2O and combustion in a PPC engine

The requirements on high efficiency and low emissions of internal combustion engines (ICEs) raise the research focus on advanced combustion concepts, e.g., premixed-charge compression ignition (PCCI), partially premixed compression ignition (PPCI), reactivity controlled compression ignition (RCCI), partially premixed combustion (PPC), gasoline compression ignition (GCI) etc. In the present study, an optically accessible engine is operated in PPC mode, featuring compression ignition of a diluted, stratified charge of gasoline-like fuel injected directly into the cylinder. A high-speed, high-power burst-mode laser system in combination with a high-speed CMOS camera is employed for diagnostics of the autoignition process which is critical for the combustion phasing and efficiency of the engine. To the authors’ best knowledge, this work demonstrates for the first time the application of the burst-system for simultaneous fuel tracer planar laser induced fluorescence (PLIF) and chemiluminescence imaging in an optical engine, at 36?kHz repetition rate. In addition, high-speed formaldehyde PLIF and chemiluminescence imaging are employed for investigation of autoignition events with a high temporal resolution (5 frames/CAD). The development of autoignition together with fuel or CH₂O distribution are simultaneously visualized using a large number of consecutive images. Prior to the onset of combustion the majority of both fuel and CH₂O are located in the recirculation zone, where the first autoignition also occurs. The ability to record, in excess of 100 PLIF images, in a single cycle brings unique possibilities to follow the in-cylinder processes without the averaging effects caused by cycle-to-cycle variations.     

Optical characterization of methanol compression-ignition combustion in a heavy-duty engine

In the search for renewable fuels, there are very few candidates as compelling as methanol. It can be derived from refuse material and industrial waste, while the infrastructure exists worldwide to support broad and fast adoption, potentially even as a “drop-in” fuel for existing vehicles with only minor modifications. The most efficient engines currently available are compression-ignition engines, however they often come with high emissions or compromises like the soot-NO_x trade-off. Methanol however, is a low sooting fuel that can potentially be used in such engines despite its high resistance to auto-ignition and reduce emissions while maintaining high engine efficiency. Due to the auto-ignition resistance, few studies of methanol compression-ignition exist and even fewer are conducted in an optically accessible engine. Here, two cases of premixed combustion and two of spray-driven combustion of methanol are studied in a Heavy-Duty optically accessible engine. Ignition and combustion propagation are characterized with a combination of time-resolved natural flame luminosity measurements and single-shot, acetone fuel-tracer, laser induced fluorescence. Additionally, Mie-scattering is used to identify the interaction between liquid spray and ignition sites in spray-driven methanol combustion. Results show that methanol combusts drastically different compared to conventional fuels, especially in spray-driven combustion. The evaporative cooling effect of methanol appears to play a major role in the auto-ignition characteristics of the delivered fuel. Ignition sites appear right at the end of injection when the evaporative cooling effect is withdrawn or at liquid length oscillations where, again the effect is momentarily retracted. To the authors’ knowledge, this has not been documented before.     

Diesel flame lift-off stabilization in the presence of laser-ignition: a numerical study

Diesel flame lift-off and stabilization in the presence of laser-ignition were numerically investigated with the method of Eulerian stochastic fields. The aim was to scrutinise the interaction between the lifted diesel flame and an ignition kernel upstream of the lifted flame. The numerical simulation was carried out in a constant-volume combustion vessel with n-heptane as fuel. The process was studied previously in an experiment employing Diesel #2 as the fuel in the same combustion vessel. In the experiment a lifted flame was first established at a position downstream of the nozzle. An ignition kernel was then initiated using a high-energy pulse laser at a position upstream of the natural lift-off position of the diesel flame. The laser-ignition kernel was modelled using a high-temperature (～2000 K) hot spot. In both experiment and simulations the upstream front of the ignition kernel was shown to remain around the initial laser ignition site for a substantially long period of time, while the downstream front of the ignition kernel propagates rapidly towards the natural lift-off position downstream of the laser ignition site. The lift-off position oscillated before the final stabilization at the natural lift-off position. The structures and the propagation speed of the reaction fronts in the laser-ignition kernel and the main flame were analysed. Two different stabilization mechanisms, the auto-ignition mechanism and the flame propagation mechanism, were identified for the naturally lifted flame and the laser-induced reaction front, respectively. A mechanism was proposed to explain the oscillation of the lift-off position.     

LES/FGM investigation of ignition and flame structure in a gasoline partially premixed combustion engine

This paper presents a joint numerical and experimental study of the ignition process and flame structures in a gasoline partially premixed combustion (PPC) engine. The numerical simulation is based on a five-dimension Flamelet-Generated Manifold (5D-FGM) tabulation approach and large eddy simulation (LES). The spray and combustion process in an optical PPC engine fueled with a primary reference fuel (70% iso-octane, 30% n-heptane by volume) are investigated using the combustion model along with laser diagnostic experiments. Different combustion modes, as well as the dominant chemical species and elementary reactions involved in the PPC engines, are identified and visualized using Chemical Explosive Mode Analysis (CEMA). The results from the LES-FGM model agree well with the experiments regarding the onset of ignition, peak heat release rate and in-cylinder pressure. The LES-FGM model performs even better than a finite-rate chemistry model that integrates the full-set of chemical kinetic mechanism in the simulation, given that the FGM model is computationally more efficient. The results show that the ignition mode plays a dominant role in the entire combustion process. The diffusion flame mode is identified in a thin layer between the ultra fuel-lean unburned mixture and the hot burned gas region that contains combustion intermediates such as CO. The diffusion flame mode contributes to a maximum of 27% of the total heat release in the later stage of combustion, and it becomes vital for the oxidation of relatively fuel-lean mixtures.     

Dynamics of triple-flames in ignition of turbulent dual fuel mixture: A direct numerical simulation study

Pilot-ignited dual fuel combustion involves a complex transition between the pilot fuel autoignition and the premixed-like phase of combustion, which is challenging for experimental measurement and numerical modelling, and not sufficiently explored. To further understand the fundamentals of the dual fuel ignition processes, the transient ignition and subsequent flame development in a turbulent dimethyl ether (DME)/methane-air mixing layer under diesel engine-relevant conditions are studied by direct numerical simulations (DNS). Results indicate that combustion is initiated by a two-stage autoignition that involves both low-temperature and high-temperature chemistry. The first stage autoignition is initiated at the stoichiometric mixture, and then the ignition front propagates against the mixture fraction gradient into rich mixtures and eventually forms a diffusively-supported cool flame. The second stage ignition kernels are spatially distributed around the most reactive mixture fraction with a low scalar dissipation rate. Multiple triple flames are established and propagate along the stoichiometric mixture, which is proven to play an essential role in the flame developing process. The edge flames gradually get close to each other with their branches eventually connected. It is the leading lean premixed branch that initiates the steady propagating methane-air flame. The time required for the initiation of steady flame is substantially shorter than the autoignition delay time of the methane-air mixture under the same thermochemical condition. Temporal evolution of the displacement speed at the flame front is also investigated to clarify the propagation characteristics of the combustion waves. Cool flame and propagation of triple flames are also identified in this study, which are novel features of the pilot-ignited dual fuel combustion.     

Soot and NO emissions control in a natural gas/diesel fuelled RCCI engine by φ-T map analysis

Soot and NO emissions are considered as major pollutants to the atmosphere from compression ignition engines. Researchers have been dedicated to the reduction of soot and NO emissions. Thus, an advance combustion regime, i.e. reactivity controlled compression ignition (RCCI), was proposed to mitigate the formation of these emissions. In this study, the dynamic ?-T (equivalence ratio vs. temperature) map analysis was applied to visualise the combustion processes associated with the in-cylinder temperature and equivalence ratio in an RCCI engine. Therefore, the soot and NO emissions can be efficiently reduced by controlling the combustion process out of the emissions islands on the ?-T map. This analysis method employs KIVA4-CHEMKIN and SENKIN code to construct ?-T maps under various conditions. To find out the significant parameters of controlling combustion process and emissions formation, four parameters were taken into consideration in a natural gas (NG) and diesel fuelled RCCI engine: NG percentage, the first start of injection (SOI) timing, split fraction of diesel and exhaust gas recirculation (EGR) rate. Each parameter was varied at three levels. Finally, the ?-T maps and final soot and NO emissions were compared among varied conditions for each parameter. It is found that the increased NG percentage can significantly reduce soot because of the absence of C-C bond in NG and the reduced diesel fuel impingement on the surface of the piston or cylinder wall. Increasing EGR can decrease the peak combustion temperature due to the dilution effect and thermal effect, consequently maintaining RCCI at low temperature combustion region. This study also indicates that dynamic ?-T map analysis is efficient at manipulating the combustion process to mitigate the soot and NO emissions formation.     

燃料敏感性对内燃机部分预混燃烧(PPC)光谱特性的影响研究

在一台光学发动机上,利用火焰高速成像技术和自发光光谱分析法,研究了燃料敏感性(S)为0和6时对发动机缸内火焰发展和燃烧发光光谱的影响。试验过程中,通过改变喷油时刻 (SOI=-25,-15和-5°CA ATDC) 使燃烧模式从部分预混燃烧过渡到传统柴油燃烧模式。通过使用正庚烷、异辛烷、乙醇混合燃料来改变燃料敏感性。结果表明,在PPC模式下(-25°CA ATDC),火焰发展过程是从近壁面区域开始着火,而后向燃烧室中心发展,即存在类似火焰传播过程,同时在燃烧室下部未燃区域也形成新的着火自燃点。敏感性对燃烧相位影响较大,对缸内燃烧火焰发展历程影响较小;高敏感性燃料OH和CH带状光谱出现的时刻推迟,表明高敏感性燃料高温反应过程推迟,且光谱强度更低,表明碳烟辐射强度减弱。在PPC到CDC之间的过渡区域(-15°CA ATDC),燃烧火焰发光更亮,燃烧反应速率比-25°CA ATDC时刻的反应速率更快。高、低敏感性燃料对缸压放热率的影响规律与-25°CA ATDC相近,此时的燃烧反应更剧烈,放热率更高,碳烟出现时刻更早。该喷油时刻下的光谱强度高于PPC模式下的光谱强度,说明此时的CO氧化反应与碳烟辐射更强。在CDC模式下(-5°CA ATDC),由于使用的燃料活性较低,燃烧放热时刻过于推迟,放热量很小,缸内燃烧压力低,因此燃料敏感性对缸压和放热率的影响不明显,但从燃烧着火图像中可以看到高敏感性燃料的火焰出现时刻较低敏感性燃料推迟。低敏感性燃料的燃烧初期蓝色火焰首先出现在燃烧室中心,着火火焰出现时刻更早,之后蓝色火焰从中心向周围扩散,呈现火焰传播为主导的燃烧过程;燃烧后期,局部混合气过浓区导致亮黄色火焰面积逐渐增大并向周围扩散。高敏感性燃料的火焰发展趋势与低敏感性燃料类似,黄色火焰的亮度与面积更小。尽管高、低敏感性燃料的OH和CH带状光谱的出现时间相近,但高敏感性燃料的光谱强度仍更低。综合分析,火焰发展结构与自发光光谱特征主要受喷油时刻的影响,燃料的敏感性主要影响着火时刻和火焰自发光光谱强度,且高敏感性燃料的光谱强度更低。     

Combustion and emission modelling of a direct-injection spark-ignition engine by combining flamelet models for premixed and diffusion flames

The combustion and emission production processes of a DISI (direct-injection spark-ignition) engine were modelled by combining flamelet models for premixed and diffusion flames. A new surrogate fuel was proposed to approximate the complicated composition of real gasoline. In contrast to simpler conventional models, the fuel was modelled as a ternary mixture of three hydrocarbons: iso-octane, n-heptane and toluene. Turbulent flame propagation in a partially premixed field was modelled by a premixed flamelet model. The mass fractions of the detailed composition of species in burnt gas were predicted by a diffusion flamelet model. For the pollutant formation modelling, a two-step oxidation of CO and H₂ was used to simulate the secondary diffusion flame. The extended Zeldovich mechanism was used to model NOx formation, while a phenomenological model was used to model soot formation. This model was initially applied to a simple geometry to investigate the fundamentals of the model's behaviour, after which three-dimensional computational fluid dynamic (CFD) simulations were performed in a realistic engine geometry.     

Understanding cool flames and warm flames

Low-temperature flames such as cool flames, warm flames, double flames, and auto-ignition assisted flames play a critical role in the performance of advanced engines and fuel design. In this paper, an overview of the recent progresses in understanding low-temperature flames and dynamics as well as their impacts on combustion, advanced engines, and fuel development will be presented. Specifically, at first, a brief review of the history of cool flames is made. Then, the recent experimental studies and computational modeling of the flame structures, dynamics, and burning limits of non-premixed and premixed cool flames, warm flames, and double flames are presented. The flammability limit diagram and the temperature-dependent chain-branching reaction pathways, respectively, for hot, warm, and cool flames at elevated temperature and pressure will be discussed and analyzed. After that, the effect of low temperature auto-ignition of auto-igniting mixtures at high ignition Damköhler numbers at engine conditions on the propagation of cool flames, warm flames, and double flames as well as turbulent flames will be discussed. Finally, a new platform using low temperature flames for the development and validation of chemical kinetic models of alternative fuels will be presented. Discussions of future research of the dynamics and control of low temperature flames under engine conditions will be made.     

A study of ignition and combustion of liquid hydrocarbon droplets in premixed fuel/air mixtures in a rapid compression machine

The combustion of two fuels with disparate reactivity such as natural gas and diesel in internal combustion engines has been demonstrated as a means to increase efficiency, reduce fuel costs and reduce pollutant formation in comparison to traditional diesel or spark-ignited engines. However, dual fuel engines are constrained by the onset of uncontrolled fast combustion (i.e., engine knock) as well as incomplete combustion, which can result in high unburned hydrocarbon emissions. To study the fundamental combustion processes of ignition and flame propagation in dual fuel engines, a new method has been developed to inject single isolated liquid hydrocarbon droplets into premixed methane/air mixtures at elevated temperatures and pressures. An opposed-piston rapid compression machine was used in combination with a newly developed piezoelectric droplet injection system that is capable of injecting single liquid hydrocarbon droplets along the stagnation plane of the combustion chamber. A high-speed Schlieren optical system was used for imaging the combustion process in the chamber. Experiments were conducted by injecting diesel droplet of various diameters (50 µm < d_o < 400 µm), into methane/air mixtures with varying equivalence ratios (0 < ϕ < 1.2) over a range of compressed temperatures (700 K < T_c < 940 K). Multiple autoignition modes was observed in the vicinity of the liquid droplets, which were followed by transition to propagating premixed flames. A computational model was developed with CONVERGE™, which uses a 141 species dual-fuel chemical kinetic mechanism for the gas phase along with a transient, analytical droplet evaporation model to define the boundary conditions at the droplet surface. The simulations capture each of the different ignition modes in the vicinity of the injected spherical diesel droplet, along with bifurcation of the ignition event into a propagating, premixed methane/air flame and a stationary diesel/air diffusion flame.     

Development and validation of an n-dodecane skeletal mechanism for spray combustion applications

n-Dodecane is a promising surrogate fuel for diesel engine study because its physicochemical properties are similar to those of the practical diesel fuels. In the present study, a skeletal mechanism for n-dodecane with 105 species and 420 reactions was developed for spray combustion simulations. The reduction starts from the most recent detailed mechanism for n-alkanes consisting of 2755 species and 11,173 reactions developed by the Lawrence Livermore National Laboratory. An algorithm combining direct relation graph with expert knowledge (DRGX) and sensitivity analysis was employed for the present skeletal reduction. The skeletal mechanism was first extensively validated in 0-D and 1-D combustion systems, including auto-ignition, jet stirred reactor (JSR), laminar premixed flame and counter flow diffusion flame. Then it was coupled with well-established spray models and further validated in 3-D turbulent spray combustion simulations under engine-like conditions. These simulations were compared with the recent experiments with n-dodecane as a surrogate for diesel fuels. It can be seen that combustion characteristics such as ignition delay and flame lift-off length were well captured by the skeletal mechanism, particularly under conditions with high ambient temperatures. Simulations also captured the transient flame development phenomenon fairly well. The results further show that ignition delay may not be the only factor controlling the stabilisation of the present flames since a good match in ignition delay does not necessarily result in improved flame lift-off length prediction.     

Effects of fuel stratification on ignition kernel development and minimum ignition energy of n-decane/air mixtures

Fuel-stratified combustion has broad application due to its promising advantages in extension of lean flammability limit, improvement of flame stabilization, enhancement of lean combustion, etc. In the literature, there are many studies on flame propagation in fuel-stratified mixtures. However, there is little attention on ignition in fuel-stratified mixtures. In this study, one-dimensional numerical simulation is conducted to investigate the ignition and spherical flame kernel propagation in fuel-stratified n-decane/air mixtures. The emphasis is placed on assessing the effects of fuel stratification on the ignition kernel propagation and critical ignition condition. First, ignition and flame kernel propagation in homogeneous n-decane/air mixture are studied and different flame regimes are identified. The minimum ignition energy (MIE) of the homogeneous n-decane/air mixture is obtained and it is found to be very sensitive to the equivalence ratio under fuel-lean conditions. Then, ignition and flame kernel propagation in fuel-stratified n-decane/air mixture are investigated. The inner equivalence ratio and stratification radius are found to have great impact on ignition kernel propagation. The MIEs at different fuel-stratification conditions are calculated. The results indicate that for fuel-lean n-decane/air mixture, fuel stratification can greatly promote ignition and reduce the MIE. Six distinct flame regimes are observed for successful ignition in fuel-stratified mixture. It is shown that the ignition kernel propagation can be induced by not only the ignition energy deposition but also the fuel-stratification. Moreover, it is found that to achieve effective ignition enhancement though fuel stratification, one needs properly choose the values of stratification radius and inner equivalence ratio.     

Minimum ignition energy and propagation dynamics of laminar premixed cool flames

Laminar premixed cool flames, induced by the coupling of low-temperature chemistry and convective-diffusive transport process, have recently attracted extensive interest in combustion and engine research. In this work, numerical simulations have been conducted using a recently developed open-source reacting flow platform reactingFOAM-SCT, to investigate the minimum ignition energy (MIE) and propagation dynamics of premixed cool flames in a 1D spherical coordinate. Results have shown that when ignition energy is below the MIE of regular hot flames, a class of cool flames could be initiated, which allow much wider flammability limits, both lean and rich, compared to hot flames. Furthermore, the overall cool flame propagation dynamics exhibit intrinsic similarity to those of hot flames, in that, they begin with an ignition kernel propagation regime, followed by two transition regimes, and eventually reach a normal flame propagation regime. However, a spherical expanding cool flame responds completely differently to stretch. Specifically, a regular outwardly propagating hot spherical flame accelerates with increasing stretch rate when the mixture Le < 1 and decelerates when Le > 1. However, it is found that a cool flame always tends to decelerate with increasing stretch rate regardless of mixture composition, exhibiting unique flame aerodynamic characteristic. This research discovers novel features of premixed cool flame initiation and propagation dynamics and sheds light on flame transition, spark-ignition system design, and advanced engine combustion control.     

Differences between PREMIER combustion in a natural gas spark-ignition engine and knocking with pressure oscillations

PREMIER (PREmixed Mixture Ignition in the End-gas Region) combustion occurs with auto-ignition in the end-gas region when the main combustion flame propagation is nearly finished. Auto-ignition is triggered by the increases in pressure and temperature induced by the main combustion flame. Similarly to engine knocking, heat is released in two stages when engines undergo this type of combustion. This pattern of heat release does not occur during normal combustion. However, engine knocking induces pressure oscillations that cause fatal damage to engines, whereas PREMIER combustion does not. The purpose of this study was to elucidate PREMIER combustion in natural gas spark-ignition engines, and differentiate the causes of knocking and PREMIER combustion. We applied combustion visualization and in-cylinder pressure analysis using a compression–expansion machine (CEM) to investigate the auto-ignition characteristics in the end-gas region of a natural gas spark-ignition engine. We occasionally observed knocking accompanied by pressure oscillations under the spark timings and initial gas conditions used to generate PREMIER combustion. No pressure oscillations were observed during normal and PREMIER combustion. Auto-ignition in the end-gas region was found to induce a secondary increase in pressure before the combustion flame reached the cylinder wall, during both knocking and PREMIER combustion. The auto-ignited flame area spread faster during knocking than during PREMIER combustion. This caused a sudden pressure difference and imbalance between the flame propagation region and the end-gas region, followed by a pressure oscillation.     

Two-stage autoignition and combustion mode evolution in boundary layer flows above a cold flat plate

Boundary layers are omnipresent in fundamental kinetic experimental facilities and practical combustion engines, which can cause ambiguity and misleading results in kinetic target acquisition and even abnormal engine combustion. In this paper, using n-heptane as a representative large hydrocarbon fuel exhibiting pronounced low-temperature chemistry (LTC), two-dimensional numerical simulation is conducted to resolve the transient autoignition phenomena affected by a boundary layer. We focus on the ignition characteristics and the subsequent combustion mode evolution of a hot combustible mixture flowing over a colder flat plate in an isobaric environment. For cases with autoignition occurring within the boundary layer, similarity is observed in the first-stage ignition as manifested by a constant temperature at all locations. The first-stage ignition is found to be rarely affected by heat and radical loss within the boundary layer. While for the main ignition event, an obvious dependence of ignition process on boundary layer thickness is identified, where the thermal-chemical process exhibits similarity at locations with similar boundary layer thickness, and the main ignition tends to first occur within the boundary layer at the domain end and generates a C-shape reaction front. It is found that sequential spontaneous autoignition is the dominant subsequent combustion mode at high-pressure conditions. At low to intermediate pressures, auto-ignition assisted flame propagation is nevertheless the dominant mode for combustion evolution. This research identifies novel features of autoignition and the subsequent combustion mode evolution affected by a cold, fully developed boundary layer, and provides useful guidance to the interpretation of abnormal combustion and combustion mode evolution in boundary layer flows.