Optical diagnostics on the reactivity controlled compression ignition (RCCI) with micro direct-injection strategy

Micro direct-injection (DI) strategy is often used to extend the operation range of the reactivity controlled compression ignition (RCCI) to high engine load, but its combustion process has not been well understood. In this study, the ignition and flame development of the micro-DI RCCI strategy were investigated on a light-duty optical engine using formaldehyde planar laser-induced fluorescence (PLIF) and high-speed natural flame luminosity imaging techniques. The premixed fuel was iso-octane and an oxygenated fuel of polyoxymethylene dimethyl ethers (PODE) was employed for DI. The fuel-air equivalence ratio of DI was kept at 0.09 and the premixed equivalence ratio was varied from 0 to 1. RCCI strategies with early and late DI timing at –25° and –5° crank angle after top dead center were studied, respectively. Results indicate that the early micro-DI RCCI features a single-stage high-temperature heat release (HTHR). The combustion in the low-reactivity region shows a combination of flame front propagation and auto-ignition. The late micro-DI RCCI presents a two-stage HTHR. The second-stage HTHR is owing to the combustion in the low-reactivity region that is dominated by flame front propagation when the premixed equivalence ratio approaches 1. For both early and late micro-DI RCCI, the intermediate-temperature heat release (ITHR) of iso-octane, indicated by formaldehyde, takes place in the low-reactivity region before the arrival of the flame front. This is quite different from the flame front propagation in spark-ignition (SI) engine that shows no ITHR in the unburned region. The DI fuel mass is a key factor that affects the combustion in the low-reactivity region. If the DI fuel mass is quite low, there is more possibility of flame front propagation; otherwise, sequential auto-ignition dominates. The emergence of the flame front propagation in micro-DI RCCI strategy reduces its combustion rate and peak pressure rise rate.     

Numerical simulation of a mixed-mode reaction front in a PPC engine

The ignition process, mode of combustion and reaction front propagation in a partially premixed combustion (PPC) engine running with a primary reference fuel (87% iso-octane, 13% n-heptane by volume) is studied numerically in a large eddy simulation. Different combustion modes, ignition front propagation, premixed flame and non-premixed flame, are observed simultaneously. Displacement speed of CO iso-surface propagation describes the transition of premixed auto-ignition to non-premixed flame. High temporal resolution optical data of CH₂O and chemiluminescence are compared with simulated results. A high speed ignition front is seen to expand through fuel-rich mixture and stabilize around stoichiometry in a non-premixed flame while lean premixed combustion occurs in the spray wake at a much slower pace. A good qualitative agreement of the distribution of chemiluminescence and CH₂O formation and destruction shows that the simulation approach sufficiently captures the driving physics of mixed-mode combustion in PPC engines. The study shows that the transition from auto-ignition to flame occurs over a period of several crank angles and the reaction front propagation can be captured using the described model.     

Advanced gasoline engine development using optical diagnostics and numerical modeling

Twenty years ago, homogeneous-charge spark-ignition gasoline engines (using carburetion, throttle-body-, or port-fuel-injection) were the dominant automotive engines. Advanced automotive engine development remained largely empirical, and stratified-charge direct-injection gasoline-engine production was blocked by lack of robustness in its combustion process [W.G. Agnew, Proc. Combust. Inst. 20 (1984) 1-17]. Today, a wide range of direct-injection gasoline engines are in (or near) production, and combustion science is playing a direct role in advanced gasoline-engine development through the simultaneous application of advanced optical diagnostics, three-dimensional computational fluid dynamics (CFD) modeling, and traditional combustion diagnostics. This paper discusses the use of optical diagnostics and CFD in five gasoline-engine combustion systems: homogeneous spark-ignition port-fuel-injection (PFI), homogeneous spark-ignition direct-injection (DI), stratified wall-guided spark-ignition direct-injection (WG-SIDI), stratified spray-guided spark-ignition direct-injection (SG-SIDI), and homogeneous-charge compression-ignition (HCCI). The emphasis is on WG-SIDI, SG-SIDI, and HCCI engines. Key in-cylinder physical processes (e.g., sprays and vaporization, turbulent fuel-air mixing, wall wetting, ignition and early flame development, turbulent partially premixed flame propagation, and emissions formation) can be visualized, quantified, and optimized through optical engine experiments and CFD-based engine modeling. Outstanding issues for stratified engines include reducing piston wall-wetting, pool fires and smoke in WG-SIDI engines, eliminating intermittent misfires in SG-SIDI engines, and optimizing lean NO_x after-treatment systems. HCCI engines require better control of combustion timing and heat-release rate over wide speed/load operating ranges, smooth transitions between operating modes, and individual cylinder sensors and controls. Future directions in optical diagnostics and modeling are suggested to improve our fundamental understanding of important in-cylinder processes and to enhance CFD modeling capabilities.     

Simultaneous 36 kHz PLIF/chemiluminescence imaging of fuel,CH2O and combustion in a PPC engine

The requirements on high efficiency and low emissions of internal combustion engines (ICEs) raise the research focus on advanced combustion concepts, e.g., premixed-charge compression ignition (PCCI), partially premixed compression ignition (PPCI), reactivity controlled compression ignition (RCCI), partially premixed combustion (PPC), gasoline compression ignition (GCI) etc. In the present study, an optically accessible engine is operated in PPC mode, featuring compression ignition of a diluted, stratified charge of gasoline-like fuel injected directly into the cylinder. A high-speed, high-power burst-mode laser system in combination with a high-speed CMOS camera is employed for diagnostics of the autoignition process which is critical for the combustion phasing and efficiency of the engine. To the authors’ best knowledge, this work demonstrates for the first time the application of the burst-system for simultaneous fuel tracer planar laser induced fluorescence (PLIF) and chemiluminescence imaging in an optical engine, at 36?kHz repetition rate. In addition, high-speed formaldehyde PLIF and chemiluminescence imaging are employed for investigation of autoignition events with a high temporal resolution (5 frames/CAD). The development of autoignition together with fuel or CH₂O distribution are simultaneously visualized using a large number of consecutive images. Prior to the onset of combustion the majority of both fuel and CH₂O are located in the recirculation zone, where the first autoignition also occurs. The ability to record, in excess of 100 PLIF images, in a single cycle brings unique possibilities to follow the in-cylinder processes without the averaging effects caused by cycle-to-cycle variations.     

Numerical simulation and validation of SI-CAI hybrid combustion in a CAI/HCCI gasoline engine

SI-CAI hybrid combustion, also known as spark-assisted compression ignition (SACI), is a promising concept to extend the operating range of CAI (Controlled Auto-Ignition) and achieve the smooth transition between spark ignition (SI) and CAI in the gasoline engine. In this study, a SI-CAI hybrid combustion model (HCM) has been constructed on the basis of the 3-Zones Extended Coherent Flame Model (ECFM3Z). An ignition model is included to initiate the ECFM3Z calculation and induce the flame propagation. In order to precisely depict the subsequent auto-ignition process of the unburned fuel and air mixture independently after the initiation of flame propagation, the tabulated chemistry concept is adopted to describe the auto-ignition chemistry. The methodology for extracting tabulated parameters from the chemical kinetics calculations is developed so that both cool flame reactions and main auto-ignition combustion can be well captured under a wider range of thermodynamic conditions. The SI-CAI hybrid combustion model (HCM) is then applied in the three-dimensional computational fluid dynamics (3-D CFD) engine simulation. The simulation results are compared with the experimental data obtained from a single cylinder VVA engine. The detailed analysis of the simulations demonstrates that the SI-CAI hybrid combustion process is characterised with the early flame propagation and subsequent multi-site auto-ignition around the main flame front, which is consistent with the optical results reported by other researchers. Besides, the systematic study of the in-cylinder condition reveals the influence mechanism of the early flame propagation on the subsequent auto-ignition.     

Effects of flash boiling injection on in-cylinder spray,mixing and combustion of a spark-ignition direct-injection engine

Higher engine efficiency and ever stringent pollutant emission regulations are considered as the most important challenges for today's automotive industry. Fast evaporation and combustion technique has caused unprecedented attention due to its potential to solve both of the above challenges. Flash boiling, which features a two-phase flow that constantly generates vapor bubbles inside the liquid spray is ideal to achieve fast evaporation and combustion inside direct-injection (DI) gasoline engines. In this study, three spray conditions, including liquid, transitional flash boiling and flare flash boiling spray were studied for comparison under cold start condition in a spark-ignition direct-injection (SIDI) optical gasoline engine. Optical access into the combustion chamber includes a quartz linear and a quartz insert on the piston. In separate experiments, we recorded the crank angle resolved spray morphology using laser scattering technique, and distribution of fuel before ignition employing laser induced fluorescence technology, as well as time-resolved color images of flame with high-speed camera. The spray morphology during the intake stroke shows stronger plume-plume and plume-air interaction under flash boiling condition, as well as smaller penetration. Then around the end of compression (before ignition), the fuel distribution is also shown to be more homogeneous with less cyclic variation under flash boiling. Finally, from the color images of the flame, it was found that with the increase of superheat degree, the diffusion rate of blue flame (generated by excited molecules) is higher, which is considered to be related with the larger fractal dimension of the flame front. Also, the combustion is more complete with less yellow flame under flash boiling.     

LES/FGM investigation of ignition and flame structure in a gasoline partially premixed combustion engine

This paper presents a joint numerical and experimental study of the ignition process and flame structures in a gasoline partially premixed combustion (PPC) engine. The numerical simulation is based on a five-dimension Flamelet-Generated Manifold (5D-FGM) tabulation approach and large eddy simulation (LES). The spray and combustion process in an optical PPC engine fueled with a primary reference fuel (70% iso-octane, 30% n-heptane by volume) are investigated using the combustion model along with laser diagnostic experiments. Different combustion modes, as well as the dominant chemical species and elementary reactions involved in the PPC engines, are identified and visualized using Chemical Explosive Mode Analysis (CEMA). The results from the LES-FGM model agree well with the experiments regarding the onset of ignition, peak heat release rate and in-cylinder pressure. The LES-FGM model performs even better than a finite-rate chemistry model that integrates the full-set of chemical kinetic mechanism in the simulation, given that the FGM model is computationally more efficient. The results show that the ignition mode plays a dominant role in the entire combustion process. The diffusion flame mode is identified in a thin layer between the ultra fuel-lean unburned mixture and the hot burned gas region that contains combustion intermediates such as CO. The diffusion flame mode contributes to a maximum of 27% of the total heat release in the later stage of combustion, and it becomes vital for the oxidation of relatively fuel-lean mixtures.     

Optical characterization of methanol compression-ignition combustion in a heavy-duty engine

In the search for renewable fuels, there are very few candidates as compelling as methanol. It can be derived from refuse material and industrial waste, while the infrastructure exists worldwide to support broad and fast adoption, potentially even as a “drop-in” fuel for existing vehicles with only minor modifications. The most efficient engines currently available are compression-ignition engines, however they often come with high emissions or compromises like the soot-NO_x trade-off. Methanol however, is a low sooting fuel that can potentially be used in such engines despite its high resistance to auto-ignition and reduce emissions while maintaining high engine efficiency. Due to the auto-ignition resistance, few studies of methanol compression-ignition exist and even fewer are conducted in an optically accessible engine. Here, two cases of premixed combustion and two of spray-driven combustion of methanol are studied in a Heavy-Duty optically accessible engine. Ignition and combustion propagation are characterized with a combination of time-resolved natural flame luminosity measurements and single-shot, acetone fuel-tracer, laser induced fluorescence. Additionally, Mie-scattering is used to identify the interaction between liquid spray and ignition sites in spray-driven methanol combustion. Results show that methanol combusts drastically different compared to conventional fuels, especially in spray-driven combustion. The evaporative cooling effect of methanol appears to play a major role in the auto-ignition characteristics of the delivered fuel. Ignition sites appear right at the end of injection when the evaporative cooling effect is withdrawn or at liquid length oscillations where, again the effect is momentarily retracted. To the authors’ knowledge, this has not been documented before.     

A study of ignition and combustion of liquid hydrocarbon droplets in premixed fuel/air mixtures in a rapid compression machine

The combustion of two fuels with disparate reactivity such as natural gas and diesel in internal combustion engines has been demonstrated as a means to increase efficiency, reduce fuel costs and reduce pollutant formation in comparison to traditional diesel or spark-ignited engines. However, dual fuel engines are constrained by the onset of uncontrolled fast combustion (i.e., engine knock) as well as incomplete combustion, which can result in high unburned hydrocarbon emissions. To study the fundamental combustion processes of ignition and flame propagation in dual fuel engines, a new method has been developed to inject single isolated liquid hydrocarbon droplets into premixed methane/air mixtures at elevated temperatures and pressures. An opposed-piston rapid compression machine was used in combination with a newly developed piezoelectric droplet injection system that is capable of injecting single liquid hydrocarbon droplets along the stagnation plane of the combustion chamber. A high-speed Schlieren optical system was used for imaging the combustion process in the chamber. Experiments were conducted by injecting diesel droplet of various diameters (50 µm < d_o < 400 µm), into methane/air mixtures with varying equivalence ratios (0 < ϕ < 1.2) over a range of compressed temperatures (700 K < T_c < 940 K). Multiple autoignition modes was observed in the vicinity of the liquid droplets, which were followed by transition to propagating premixed flames. A computational model was developed with CONVERGE™, which uses a 141 species dual-fuel chemical kinetic mechanism for the gas phase along with a transient, analytical droplet evaporation model to define the boundary conditions at the droplet surface. The simulations capture each of the different ignition modes in the vicinity of the injected spherical diesel droplet, along with bifurcation of the ignition event into a propagating, premixed methane/air flame and a stationary diesel/air diffusion flame.     

Effects of fuel stratification on ignition kernel development and minimum ignition energy of n-decane/air mixtures

Fuel-stratified combustion has broad application due to its promising advantages in extension of lean flammability limit, improvement of flame stabilization, enhancement of lean combustion, etc. In the literature, there are many studies on flame propagation in fuel-stratified mixtures. However, there is little attention on ignition in fuel-stratified mixtures. In this study, one-dimensional numerical simulation is conducted to investigate the ignition and spherical flame kernel propagation in fuel-stratified n-decane/air mixtures. The emphasis is placed on assessing the effects of fuel stratification on the ignition kernel propagation and critical ignition condition. First, ignition and flame kernel propagation in homogeneous n-decane/air mixture are studied and different flame regimes are identified. The minimum ignition energy (MIE) of the homogeneous n-decane/air mixture is obtained and it is found to be very sensitive to the equivalence ratio under fuel-lean conditions. Then, ignition and flame kernel propagation in fuel-stratified n-decane/air mixture are investigated. The inner equivalence ratio and stratification radius are found to have great impact on ignition kernel propagation. The MIEs at different fuel-stratification conditions are calculated. The results indicate that for fuel-lean n-decane/air mixture, fuel stratification can greatly promote ignition and reduce the MIE. Six distinct flame regimes are observed for successful ignition in fuel-stratified mixture. It is shown that the ignition kernel propagation can be induced by not only the ignition energy deposition but also the fuel-stratification. Moreover, it is found that to achieve effective ignition enhancement though fuel stratification, one needs properly choose the values of stratification radius and inner equivalence ratio.     

Diesel flame lift-off stabilization in the presence of laser-ignition: a numerical study

Diesel flame lift-off and stabilization in the presence of laser-ignition were numerically investigated with the method of Eulerian stochastic fields. The aim was to scrutinise the interaction between the lifted diesel flame and an ignition kernel upstream of the lifted flame. The numerical simulation was carried out in a constant-volume combustion vessel with n-heptane as fuel. The process was studied previously in an experiment employing Diesel #2 as the fuel in the same combustion vessel. In the experiment a lifted flame was first established at a position downstream of the nozzle. An ignition kernel was then initiated using a high-energy pulse laser at a position upstream of the natural lift-off position of the diesel flame. The laser-ignition kernel was modelled using a high-temperature (～2000 K) hot spot. In both experiment and simulations the upstream front of the ignition kernel was shown to remain around the initial laser ignition site for a substantially long period of time, while the downstream front of the ignition kernel propagates rapidly towards the natural lift-off position downstream of the laser ignition site. The lift-off position oscillated before the final stabilization at the natural lift-off position. The structures and the propagation speed of the reaction fronts in the laser-ignition kernel and the main flame were analysed. Two different stabilization mechanisms, the auto-ignition mechanism and the flame propagation mechanism, were identified for the naturally lifted flame and the laser-induced reaction front, respectively. A mechanism was proposed to explain the oscillation of the lift-off position.     

燃料敏感性对内燃机部分预混燃烧(PPC)光谱特性的影响研究

在一台光学发动机上,利用火焰高速成像技术和自发光光谱分析法,研究了燃料敏感性(S)为0和6时对发动机缸内火焰发展和燃烧发光光谱的影响。试验过程中,通过改变喷油时刻 (SOI=-25,-15和-5°CA ATDC) 使燃烧模式从部分预混燃烧过渡到传统柴油燃烧模式。通过使用正庚烷、异辛烷、乙醇混合燃料来改变燃料敏感性。结果表明,在PPC模式下(-25°CA ATDC),火焰发展过程是从近壁面区域开始着火,而后向燃烧室中心发展,即存在类似火焰传播过程,同时在燃烧室下部未燃区域也形成新的着火自燃点。敏感性对燃烧相位影响较大,对缸内燃烧火焰发展历程影响较小;高敏感性燃料OH和CH带状光谱出现的时刻推迟,表明高敏感性燃料高温反应过程推迟,且光谱强度更低,表明碳烟辐射强度减弱。在PPC到CDC之间的过渡区域(-15°CA ATDC),燃烧火焰发光更亮,燃烧反应速率比-25°CA ATDC时刻的反应速率更快。高、低敏感性燃料对缸压放热率的影响规律与-25°CA ATDC相近,此时的燃烧反应更剧烈,放热率更高,碳烟出现时刻更早。该喷油时刻下的光谱强度高于PPC模式下的光谱强度,说明此时的CO氧化反应与碳烟辐射更强。在CDC模式下(-5°CA ATDC),由于使用的燃料活性较低,燃烧放热时刻过于推迟,放热量很小,缸内燃烧压力低,因此燃料敏感性对缸压和放热率的影响不明显,但从燃烧着火图像中可以看到高敏感性燃料的火焰出现时刻较低敏感性燃料推迟。低敏感性燃料的燃烧初期蓝色火焰首先出现在燃烧室中心,着火火焰出现时刻更早,之后蓝色火焰从中心向周围扩散,呈现火焰传播为主导的燃烧过程;燃烧后期,局部混合气过浓区导致亮黄色火焰面积逐渐增大并向周围扩散。高敏感性燃料的火焰发展趋势与低敏感性燃料类似,黄色火焰的亮度与面积更小。尽管高、低敏感性燃料的OH和CH带状光谱的出现时间相近,但高敏感性燃料的光谱强度仍更低。综合分析,火焰发展结构与自发光光谱特征主要受喷油时刻的影响,燃料的敏感性主要影响着火时刻和火焰自发光光谱强度,且高敏感性燃料的光谱强度更低。     

超声速预混可燃气流的点火与燃烧

在激波风洞一激波管组合设备上开展了碳氢燃料超声速预混可燃气流的点火与燃烧实验研究。实验结果表明:利用激波对燃料进行预热,并以高温燃气作为引导火焰,可以有效缩短汽油空气超声速可燃混气的点火延迟时间,使之缩短到 0.2 ms以下。利用纹影照片对超声速燃烧流场结构作出了分析;研究了超声速预混可燃气流的温度以及当量比对超声速燃烧流场结构、点火与火焰传播特性的影响。     

Dynamics of triple-flames in ignition of turbulent dual fuel mixture: A direct numerical simulation study

Pilot-ignited dual fuel combustion involves a complex transition between the pilot fuel autoignition and the premixed-like phase of combustion, which is challenging for experimental measurement and numerical modelling, and not sufficiently explored. To further understand the fundamentals of the dual fuel ignition processes, the transient ignition and subsequent flame development in a turbulent dimethyl ether (DME)/methane-air mixing layer under diesel engine-relevant conditions are studied by direct numerical simulations (DNS). Results indicate that combustion is initiated by a two-stage autoignition that involves both low-temperature and high-temperature chemistry. The first stage autoignition is initiated at the stoichiometric mixture, and then the ignition front propagates against the mixture fraction gradient into rich mixtures and eventually forms a diffusively-supported cool flame. The second stage ignition kernels are spatially distributed around the most reactive mixture fraction with a low scalar dissipation rate. Multiple triple flames are established and propagate along the stoichiometric mixture, which is proven to play an essential role in the flame developing process. The edge flames gradually get close to each other with their branches eventually connected. It is the leading lean premixed branch that initiates the steady propagating methane-air flame. The time required for the initiation of steady flame is substantially shorter than the autoignition delay time of the methane-air mixture under the same thermochemical condition. Temporal evolution of the displacement speed at the flame front is also investigated to clarify the propagation characteristics of the combustion waves. Cool flame and propagation of triple flames are also identified in this study, which are novel features of the pilot-ignited dual fuel combustion.     

Unsteady deflagration speed of an auto-ignitive dimethyl-ether (DME)/air mixture at stratified conditions

The propagation speed of an auto-ignitive dimethyl-ether (DME)/air mixture at elevated pressures and subjected to monochromatic temperature oscillations is numerically evaluated in a one-dimensional statistically stationary configuration using fully resolved numerical simulations with reduced kinetics and transport. Two sets of conditions with temperatures within and slightly above the negative temperature coefficient (NTC) regime are simulated to investigate the fundamental aspects of auto-ignition and flame propagation along with the transition from auto-ignitive deflagration to spontaneous propagation regimes under thermal stratification. Contrary to the standard laminar flame speed, the steady propagation speed of an auto-ignitive front is observed to scale proportionally to its level of upstream reactivity. It is shown that this interdependence is primarily influenced by the characteristic residence time and the homogeneous auto-ignition delay. Furthermore, the unsteady reaction front in either of the two cases responds distinctly to the imposed stratification. Specifically, the results in both cases show that the dynamic flame response depends on the mean temperature at the flame base T_b and the time-scale of thermal stratification. It is also found that, based on T_b and the propensity of the mixture to two-stage chemistry, the instantaneous peak propagation speed and the overall time taken to achieve that speed differs considerably. A displacement speed analysis is carried out to elucidate the underlying combustion modes that are responsible for such a variation in flame response.     

Understanding cool flames and warm flames

Low-temperature flames such as cool flames, warm flames, double flames, and auto-ignition assisted flames play a critical role in the performance of advanced engines and fuel design. In this paper, an overview of the recent progresses in understanding low-temperature flames and dynamics as well as their impacts on combustion, advanced engines, and fuel development will be presented. Specifically, at first, a brief review of the history of cool flames is made. Then, the recent experimental studies and computational modeling of the flame structures, dynamics, and burning limits of non-premixed and premixed cool flames, warm flames, and double flames are presented. The flammability limit diagram and the temperature-dependent chain-branching reaction pathways, respectively, for hot, warm, and cool flames at elevated temperature and pressure will be discussed and analyzed. After that, the effect of low temperature auto-ignition of auto-igniting mixtures at high ignition Damköhler numbers at engine conditions on the propagation of cool flames, warm flames, and double flames as well as turbulent flames will be discussed. Finally, a new platform using low temperature flames for the development and validation of chemical kinetic models of alternative fuels will be presented. Discussions of future research of the dynamics and control of low temperature flames under engine conditions will be made.     

Acceleration of the chemistry solver for modeling DI engine combustion using dynamic adaptive chemistry (DAC) schemes

Acceleration of the chemistry solver for engine combustion is of much interest due to the fact that in practical engine simulations extensive computational time is spent solving the fuel oxidation and emission formation chemistry. A dynamic adaptive chemistry (DAC) scheme based on a directed relation graph error propagation (DRGEP) method has been applied to study homogeneous charge compression ignition (HCCI) engine combustion with detailed chemistry (over 500 species) previously using an R-value-based breadth-first search (RBFS) algorithm, which significantly reduced computational times (by as much as 30-fold). The present paper extends the use of this on-the-fly kinetic mechanism reduction scheme to model combustion in direct-injection (DI) engines. It was found that the DAC scheme becomes less efficient when applied to DI engine simulations using a kinetic mechanism of relatively small size and the accuracy of the original DAC scheme decreases for conventional non-premixed combustion engine. The present study also focuses on determination of search-initiating species, involvement of the NO_x chemistry, selection of a proper error tolerance, as well as treatment of the interaction of chemical heat release and the fuel spray. Both the DAC schemes were integrated into the ERC KIVA-3v2 code, and simulations were conducted to compare the two schemes. In general, the present DAC scheme has better efficiency and similar accuracy compared to the previous DAC scheme. The efficiency depends on the size of the chemical kinetics mechanism used and the engine operating conditions. For cases using a small n-heptane kinetic mechanism of 34 species, 30% of the computational time is saved, and 50% for a larger n-heptane kinetic mechanism of 61 species. The paper also demonstrates that by combining the present DAC scheme with an adaptive multi-grid chemistry (AMC) solver, it is feasible to simulate a direct-injection engine using a detailed n-heptane mechanism with 543 species with practical computer time.     

Combustion and emission modelling of a direct-injection spark-ignition engine by combining flamelet models for premixed and diffusion flames

The combustion and emission production processes of a DISI (direct-injection spark-ignition) engine were modelled by combining flamelet models for premixed and diffusion flames. A new surrogate fuel was proposed to approximate the complicated composition of real gasoline. In contrast to simpler conventional models, the fuel was modelled as a ternary mixture of three hydrocarbons: iso-octane, n-heptane and toluene. Turbulent flame propagation in a partially premixed field was modelled by a premixed flamelet model. The mass fractions of the detailed composition of species in burnt gas were predicted by a diffusion flamelet model. For the pollutant formation modelling, a two-step oxidation of CO and H₂ was used to simulate the secondary diffusion flame. The extended Zeldovich mechanism was used to model NOx formation, while a phenomenological model was used to model soot formation. This model was initially applied to a simple geometry to investigate the fundamentals of the model's behaviour, after which three-dimensional computational fluid dynamic (CFD) simulations were performed in a realistic engine geometry.     

Flow, spray and combustion analysis by laser techniques in the combustion chamber of a direct-injection diesel engine

The purpose of this paper is to show how the analysis of in -cylinder flow, fuel injection, and combustion by means of state-of-the-art optical techniques, as laser light-sheet, laser doppler anemometry and laser shadowgraphy, can help to support the understanding of the interaction of swirl flow development, spray formation, auto-ignition and combustion in near production-line direct-injection diesel engines and thus advances the development of engines with lower fuel consumption and emissions.     

Two-stage autoignition and combustion mode evolution in boundary layer flows above a cold flat plate

Boundary layers are omnipresent in fundamental kinetic experimental facilities and practical combustion engines, which can cause ambiguity and misleading results in kinetic target acquisition and even abnormal engine combustion. In this paper, using n-heptane as a representative large hydrocarbon fuel exhibiting pronounced low-temperature chemistry (LTC), two-dimensional numerical simulation is conducted to resolve the transient autoignition phenomena affected by a boundary layer. We focus on the ignition characteristics and the subsequent combustion mode evolution of a hot combustible mixture flowing over a colder flat plate in an isobaric environment. For cases with autoignition occurring within the boundary layer, similarity is observed in the first-stage ignition as manifested by a constant temperature at all locations. The first-stage ignition is found to be rarely affected by heat and radical loss within the boundary layer. While for the main ignition event, an obvious dependence of ignition process on boundary layer thickness is identified, where the thermal-chemical process exhibits similarity at locations with similar boundary layer thickness, and the main ignition tends to first occur within the boundary layer at the domain end and generates a C-shape reaction front. It is found that sequential spontaneous autoignition is the dominant subsequent combustion mode at high-pressure conditions. At low to intermediate pressures, auto-ignition assisted flame propagation is nevertheless the dominant mode for combustion evolution. This research identifies novel features of autoignition and the subsequent combustion mode evolution affected by a cold, fully developed boundary layer, and provides useful guidance to the interpretation of abnormal combustion and combustion mode evolution in boundary layer flows.