Direct Electrochemistry and Electrocatalysis of Hemoglobin Based on Nafion‐Room Temperature Ionic Liquids‐Multiwalled Carbon Nanotubes Composite Film

A robust and effective composite film combined the benefits of Nafion, room temperature ionic liquid (RTIL) and multi‐wall carbon nanotubes (MWNTs) was prepared. Hemoglobin (Hb) was successfully immobilized on glassy carbon electrode surface by entrapping in the composite film. Direct electrochemistry and electrocatalysis of immobilized Hb were investigated in detail. A pair of well‐defined and quasi‐reversible redox peaks of Hb was obtained in 0.10 mol·L^?1 pH 7.0 phosphate buffer solution (PBS), indicating that the Nafion‐RTIL‐MWNTs film showed an obvious promotion for the direct electron transfer between Hb and the underlying electrode. The immobilized Hb exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis current was linear to H₂O₂ concentration in the range of 2.0×10^?6 to 2.5×10^?4 mol·L^?1, with a detection limit of 8.0×10^?7 mol·L^?1 (S/N=3). The apparent Michaelis‐Menten constant (K_m^app) was calculated to be 0.34 mmol·L^?1. Moreover, the modified electrode displayed a good stability and reproducibility. Based on the composite film, a third‐generation reagentless biosensor could be constructed for the determination of H₂O₂.     

Direct Electrochemistry and Electrocatalysis of Hemoglobin/ZnO‐Chitosan/nano‐Au Modified Glassy Carbon Electrode

The highly efficient H₂O₂ biosensor was fabricated on the basis of the complex films of hemoglobin (Hb), nano ZnO, chitosan (CHIT) dispersed solution and nano Au immobilized on glassy carbon electrode (GCE). Biocompatible ZnO‐CHIT composition provided a suitable microenvironment to keep Hb bioactivity (Michaelis‐Menten constant of 0.075 mmol L^?1). The presence of nano Au in matrix could effectively enhance electron transfer between Hb and electrode. The electrochemical behaviors and effects of solution pH values were carefully examined in this paper. The (ZnO‐CHIT)‐Au‐Hb/GCE demonstrated excellently electrocatalytical ability for H₂O₂. This biosensor had a fast response to H₂O₂ less than 4 s and excellent linear relationships were obtained in the concentration range from1.94×10^?7 to 1.73×10^?3 mol L^?1 with the detection limit of 9.7×10^?8 mol L^?1 (S/N=3) under the optimum conditions. Moreover, the stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Direct Electrochemistry of Hemoglobin Immobilized on Carbon‐Coated Iron Nanoparticles for Amperometric Detection of Hydrogen Peroxide

A novel method for preparation of hydrogen peroxide biosensor was presented based on immobilization of hemoglobin (Hb) on carbon‐coated iron nanoparticles (CIN). CIN was firstly dispersed in a chitosan solution and cast onto a glassy carbon electrode to form a CIN/chitosan composite film modified electrode. Hb was then immobilized onto the composite film with the cross‐linking of glutaraldehyde. The immobilized Hb displayed a pair of stable and quasireversible redox peaks and excellent electrocatalytic reduction of hydrogen peroxide (H₂O₂), which leading to an unmediated biosensor for H₂O₂. The electrocatalytic response exhibited a linear dependence on H₂O₂ concentration in a wide range from 3.1 μM to 4.0 mM with a detection limit of 1.2 μM (S/N=3). The designed biosensor exhibited acceptable stability, long‐term life and good reproducibility.     

Hemoglobin‐Titanate Composite Based Biosensor for the Amperometric Determination of Hydrogen Peroxide in Acidic Medium

A hemoglobin‐titanate composite based biosensor was chosen for determination of H₂O₂ in an acidic medium. CV results of the Hb‐titanate modified pyrolytic graphite electrode showed a pair of well‐defined, quasi‐reversible redox peaks centered at ?246 mV (vs. Ag/AgCl) in a pH 5.0 HAc‐NaAc buffer solution. The modified electrode exhibited good electrocatalytic response for monitoring H₂O₂ and had a large linear detection range from 20 μM to 3.2 mM with a detection limit of 8 μM (S/N=3) and a sensitivity of 29.7 mA M^?1 cm^?2 in the pH 5.0 solution. The biosensor also possessed good long term storage stability.     

Electrochemical Surface Structuring with Polyaniline Wrapped Hb for Hydrogen Peroxide Biosensing

Through the electrodeposition of aniline with hemoglobin (Hb) on zincoxide‐gold colloidal sols (ZnO‐AuNPs) modified indium oxide electrode, a hydrogen peroxide (H₂O₂) biosensor was constructed. Polyaniline (PANI) form a nano‐cage wrapped Hb, which provided a comfortable and stable site for the immobization of Hb. UV‐vis spectrum was employed to characterize Hb retained original structure in the resulting Hb‐PANI/ZnO‐AuNPs membrane. Electrochemical investigation of the biosensor showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa= ‐0.139 V and E_pc = ‐0.238 V (vs. SCE) in 0.1 M pH 7.0 phosphate buffer solution at the scan rate of 100 mV/s. The biosensor displayed a fast response time (<3 s) and broad linear response to H₂O₂ in the range from 1.5 μM to 1.7 mM with a detection limit of 0.8 μM (S/N = 3).     

A New Electrochemical Biosensor for Determination of Hydrogen Peroxide in Food Based on Well‐Dispersive Gold Nanoparticles on Graphene Oxide

Herein, we describe a new method for the detection of hydrogen peroxide (H₂O₂) in food by using an electrochemical biosensor. Initially, ultrafine gold nanoparticles dispersed on graphene oxide (AuNP‐GO) were synthesized by the redox reaction between AuCl₄^? and GO, and thionine‐catalase conjugates were then assembled onto the AuNP‐GO surface on a glassy carbon electrode. With the aid of the AuNP‐GO, the as‐prepared biosensor exhibited good electrocatalytic efficiency toward the reduction of H₂O₂ in pH 5.8 acetic acid buffer. Under optimal conditions, the dynamic responses of the biosensor toward H₂O₂ were achieved in the range from 0.1 µM to 2.3 mM, and the detection limit (LOD) was 0.01 µM at 3s_B. The Michaelis–Menten constant was measured to be 0.98 mM. In addition, the repeatability, reproducibility, selectivity and stability of the biosensor were investigated and evaluated in detail. Finally, the method was applied for sensing H₂O₂ in spiked or naturally contaminated samples including sterilized milk, apple juices, watermelon juice, coconut milk, and mango juice, receiving good correspondence with the results from the permanganate titration method. The disposable biosensor could offer a great potential for rapid, cost‐effective and on‐field analysis of H₂O₂ in foodstuff.     

A Third‐Generation Hydrogen Peroxide Biosensor Based on Horseradish Peroxidase Immobilized in Carbon Nanotubes/ SBA‐15 Film

A new third‐generation biosensor for H₂O₂ assay was developed on the basis of the immobilization of horseradish peroxidase (HRP) in a nanocomposite film of carbon nanotubes (CNTs)‐SBA‐15 modified gold electrode. The biological activity of HRP immobilizing in the composite film was characterized by UV‐vis spectra. The HRP immobilized in the nanocomposite matrix displayed excellent electrocatalytic activity to the reduction of H₂O₂. The effects of the experimental variables such as solution pH and working potential were investigated using steady‐state amperometry. Under the optimal conditions, the resulting biosensor showed a linear range from 1 µM to 7 mM and a detection limit of 0.5 µM (S/N=3). Moreover, the stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Amperometric Biosensor for Hydrogen Peroxide,Using Supramolecularly Immobilized Horseradish Peroxidase on the β‐Cyclodextrin‐Coated Gold Electrode

Horseradish peroxidase, previously modified with 1‐adamantane moieties, was supramolecularly immobilized on gold electrodes coated with perthiolated β‐cyclodextrin. The functionalized electrode was employed for the construction of an amperometric biosensor device for hydrogen peroxide using 1 mM hydroquinone as electrochemical mediator. The biosensor exhibited a fast amperometric response (6 s) and a good linear response toward H₂O₂ concentration between 12 μM and 450 μM. The biosensor showed a sensitivity of 1.02 mA/M cm², and a very low detection limit of 5 μM. The electrode retained 97% of its initial electrocatalytic activity after 30 days of storage at 4 ⁰C in 50 mM sodium phosphate buffer, pH 7.0.     

An Enzyme‐free H2O2 Sensor Based on Poly(2‐Aminophenylbenzimidazole)/Gold Nanoparticles Coated Pencil Graphite Electrode

A poly(2‐aminophenylbenzimidazole)/gold nanoparticles (P2AB/AuNPs) coated disposable pencil graphite electrode (PGE) was fabricated as an enzyme‐free sensor for the H₂O₂ determination. P2AB/AuNPs and P2AB were successfully synthesized electrochemically on PGE in acetonitrile for the first time. The coatings were characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, Energy‐dispersive X‐ray spectroscopy, Surface‐enhanced Raman spectroscopy, and UV‐Vis spectroscopy. AuNPs interacted with P2AB as carrier enhances the electrocatalytic activity towards reduction of H₂O₂. The analytical performance was evaluated in a 100 mM phosphate buffer solution at pH 6.5 by amperometry. The steady state current vs. H₂O₂ concentration is linear in the range of 0.06 to 100 mM (R²=0.992) with a limit of detection 3.67×10^?5 M at ?0.8 V vs. SCE and no interference is caused by ascorbic acid, dopamine, uric acid, and glucose. The examination for the sensitive determination of H₂O₂ was conducted in commercially available hair oxidant solution. The results demonstrate that P2AB/AuNPs/PGE has potential applications as a sensing material for quantitative determination of H₂O₂.     

Direct Electrochemistry of Hemoglobin in Layer‐by‐Layer Films Assembled with DNA and Room Temperature Ionic Liquid

Based on electrostatic interaction and electrodeposition, poly‐anionic deoxyribonucleic acid (DNA), room temperature ionic liquid 1‐butyl‐3‐methyl‐imidazolium tetrafluoroborate (BMIMBF₄), hemoglobin (Hb) and Poly(diallyldimethylammonium chloride) (PDDA) were successfully assembled into Hb/IL/DNA/PDDA layer‐by‐layer complex films on the surface of ITO electrode. FTIR spectroscopy, electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were used to characterize the composite film. The obtained results demonstrated that the Hb molecule in the film kept its native structure and showed its good electrochemical behavior. A pair of well‐defined redox peaks of Hb with the formal potentials (E°′) of ?0.180 V (vs. SCE) was appeared in phosphate buffer solution (PBS, pH 7.0). The Hb/IL/DNA/PDDA/ITO modified electrode also showed an excellent electrocatalytic behavior to the reduction of hydrogen peroxide (H₂O₂). Therefore, the IL/DNA/PDDA complex film as a novel matrix open up a possibility for further study on the direct electrochemistry of other proteins and the fabrication of the third‐generation electrochemical biosensors.     

A Hydrogen Peroxide Biosensor Based on Room Temperature Ionic Liquid Functionalized Graphene Modified Carbon Ceramic Electrode

A room temperature ionic liquid (IL) 1‐butyl‐3‐methylimidazolium hexafluorophosphate functionalized graphene (GE) was prepared and a hydrogen peroxide (H₂O₂) biosensor was fabricated by immobilizing hemoglobin (Hb) into the IL‐GE composite film. UV‐visible and Fourier transform infrared spectra of the composite film indicated that Hb retained its native structure in the film. Electrochemical investigation of the biosensor showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa=?0.209 V and E_pc= ?0.302 V (vs. SCE) in pH 7.0 phosphate buffer solution at the scan rate of 100 mV/s. To the reduction of H₂O₂, the biosensor had a good linear range from 8.0×10^?7 to 1.8×10^?4 mol/L with a detection limit of 3.0×10^?7 mol/L. The apparent Michaelis‐Menten constant K^app_M was estimated to be 3.4×10^?5 mol/L.     

Functionalization of Single‐Walled Carbon Nanotubes with Cubic Prussian Blue and Its Application for Amperometric Sensing

In this work, we synthesized electroactive cubic Prussian blue (PB) modified single‐walled carbon nanotubes (SWNTs) nanocomposites using the mixture solution of ferric‐(III) chloride and potassium ferricyanide under ambient conditions. The successful fabrication of the PB‐SWNTs nanocomposites was confirmed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV‐vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and cyclic voltammetry (CV). PB nanocrystallites are observed to be finely attached on the SWNTs sidewalls in which the SWNTs not only act as a carrier of PB nanocrystallites but also as Fe(III)‐reducer. The electrochemical properties of PB‐SWNTs nanocomposites were also investigated. Using the electrodeposition technique, a thin film of PB‐SWNTs/chitosan nanocomposites was prepared onto glassy carbon electrode (GCE) for the construction of a H₂O₂ sensor. PB‐SWNTs/chitosan nanocomposites film shows enhanced electrocatalytic activity towards the reduction of H₂O₂ and the amperometric responses show a linear dependence on the concentration of H₂O₂ in a range of 0.5–27.5 mM and a low detection limit of 10 nM at the signal‐to‐noise ratio of 3. The time required to reach the 95% steady state response was less than 2 s. CV studies demonstrate that the modified electrode has outstanding stability. In addition, a glucose biosensor is further developed through the simple one‐step electrodeposition method. The observed wide concentration range, high stability and high reproducibility of the PB‐SWNTs/chitosan nanocomposites film make them promising for the reliable and durable detection of H₂O₂ and glucose.     

Direct Electrochemistry and Application in Electrocatalysis of Hemoglobin in a Polyacrylic Resin‐Gold Colloid Nanocomposite Film

A novel nanocomposite integrating the good biocompatibility of polyacrylic resin nanoparticles (PAR) and the good conductivity of colloidal gold nanoparticles was proposed to construct the matrix for the immobilization of hemoglobin (Hb) on the surface of a glassy carbon electrode (GCE). UV‐vis spectra demonstrated that Hb preserved its native structure after being entrapped into the composite film. The direct electrochemistry of hemoglobin (Hb) in this nanocomposite films showed a pair of well‐defined and quasi‐reversible cyclic voltammetric peaks with a formal potential of ?0.307 mV and a constant electron transfer rate of 2.51±0.2 s^?1. The resultant amperometric biosensor showed fast responses to the analytes with excellent detection limits of 0.2 µM for H₂O₂ and 0.89 µM for TCA (S/N=3), and high sensitivity of 1108.6 for H₂O₂ and 77.14 mA cm^?2 M^?1 for TCA, respectively. The linear current response was found in the range from 0.59 to 7.3 µM (R²=0.9996) for H₂O₂ and from 5 to 85 µM (R²=0.9996) for TCA, while the superior apparent Michaelis–Menten constant was 0.012 mM for H₂O₂ and 0.536 mM for TCA, respectively. Therefore, the PAR‐Au‐Hb nanocomposite as a novel matrix opens up a possibility for further study on the direct electrochemistry of other proteins.     

Electrochemical Fabrication of Prussian Blue Nanocube‐decorated Electroreduced Graphene Oxide for Amperometric Sensing of NADH

In this study, Prussian blue (PB) film on the electroreduced graphene oxide (ERGO)‐modified Au electrode surface (ERGO/PB) is easily prepared by means of cyclic voltammetric technique in the mixture of K₃Fe(CN)₆ and FeCl₃. Its electrochemical behaviors for NADH biosensor are studied. The structural and morphological characters of modified electrode material are analyzed with using of XPS, XRD, Raman, EDS, and SEM techniques. ERGO/PB hybrid nanocomposite for NADH biosensor is exhibited to the higher catalytic effect (linear range from 1.0 to 100 μM, detection limit of 0.23 μM at S/N=3) compared to naked Au, ERGO‐modified Au, and PB‐modified Au electrodes. In addition to, ERGO/PB electrode was used to voltammetric and amperometric detection of H₂O₂. ERGO/PB electrodes also showed the same behavior as the NADH sensor. This ERGO/PB‐modified electrode supplied a simple, new, and low‐cost route for amperometric sensing of both NADH and H₂O₂.     

Carbon Nanotubes‐Based Amperometric Cholesterol Biosensor Fabricated Through Layer‐by‐Layer Technique

A carbon nanotubes‐based amperometric cholesterol biosensor has been fabricated through layer‐by‐layer (LBL) deposition of a cationic polyelectrolyte (PDDA, poly(diallyldimethylammonium chloride)) and cholesterol oxidase (ChOx) on multi‐walled carbon nanotubes (MWNTs)‐modified gold electrode, followed by electrochemical generation of a nonconducting poly(o‐phenylenediamine) (PPD) film as the protective coating. Electrochemical impedance measurements have shown that PDDA/ChOx multilayer film could be formed uniformly on MWNTs‐modified gold electrode. Due to the strong electrocatalytic properties of MWNTs toward H₂O₂ and the low permeability of PPD film for electroacitve species, such as ascorbic acid, uric acid and acetaminophen, the biosensor has shown high sensitivity and good anti‐interferent ability in the detection of cholesterol. The effect of the pH value of the detection solution on the response of the biosensor was also investigated. A linear range up to 6.0 mM has been observed for the biosensor with a detection limit of 0.2 mM. The apparent Michaelis‐Menten constant and the maximum response current density were calculated to be 7.17 mM and 7.32 μA cm^?2, respectively.     

An Organic Sol‐Gel Film as Modifier to Construct Biosensor

A new amperometric biosensor for hydrogen peroxide (H₂O₂) was developed by adsorbing hemoglobin (Hb) on an organic sol‐gel film. The organic sol‐gel was prepared using resorcinol and formaldehyde as monomers. This sol‐gel film shows a biocompatible microenvironment for retaining the native activity of the adsorbed Hb. The direct electron transfer between Hb and electrode is achieved. Hb adsorbed on the film shows an enzyme‐like catalytic activity for the reduction of H₂O₂. The reduction peak currents are proportional linearly to the concentration of hydrogen peroxide in the range of 6×10^?8 to 3.6×10^?6 M, with a detection limit of 2.4×10^?8 M (S/N=3). This research enlarges the applications of organic sol‐gel materials in biosensor field.     

Electrochemistry and Electrocatalysis of a Nafion/Nano‐CaCO3/Hb Film Modified Carbon Ionic Liquid Electrode Using BMIMPF6 as Binder

In this paper a room temperature ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) was used as binder for the construction of carbon ionic liquid electrode (CILE) and a new electrochemical biosensor was developed for determination of H₂O₂ by immobilization of hemoglobin (Hb) in the composite film of Nafion/nano‐CaCO₃ on the surface of CILE. The Hb modified electrode showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa and E_pc as ?0.265 V and ?0.470 V (vs. SCE). The formal potential (E°′) was got by the midpoint of E_pa and E_pc as ?0.368 V, which was the characteristic of Hb Fe(III)/Fe(II) redox couples. The peak to peak separation was 205 mV in pH 7.0 Britton–Robinson (B–R) buffer solution at the scan rate of 100 mV/s. The direct electrochemistry of Hb in the film was carefully investigated and the electrochemical parameters of Hb on the modified electrode were calculated as α=0.487 and k_s=0.128 s^?1. The Nafion/nano‐CaCO₃/Hb film electrode showed good electrocatalysis to the reduction of H₂O₂ in the linear range from 8.0 to 240.0 μmol/L and the detection limit as 5.0 μmol/L (3σ). The apparent Michaelis–Menten constant (K_M^app) was estimated to be 65.7 μmol/L. UV‐vis absorption spectroscopy and FT‐IR spectroscopy showed that Hb in the Nafion/nano‐CaCO₃ composite film could retain its native structure.     

Amperometric Flow‐Biosensor for Cyanide Based on an Inhibitory Effect upon Bioelectrocatalytic Reduction of Oxygen by Peroxidase‐Modified Carbon‐Felt

A novel, simple and relative highly sensitive amperometric flow biosensor for cyanide was developed by using horseradish peroxidase (HRP)‐adsorbed carbon‐felt (CF), based on an inhibitory effect on the HRP‐catalyzed O₂ reduction. The HRP‐CF showed a sufficient bioelecrocatalytic activity for O₂ reduction in the potential region from 0 to ?0.5 V at pH 5.0, due to a direct electron transfer‐based O₂ reduction process via ferrous‐HRP and compound III. This HRP‐catalyzed O₂ reduction was reversibly inhibited by cyanide, which enabled to fabricate a novel and simple reagentless (i.e., no requirement of the ordinary substrate, H₂O₂, and the electron transfer mediators) flow‐biosensor for cyanide. When air‐saturated 0.1 M phosphate buffer (pH 5.0) was used as a carrier under the applied potential of ?0.2 V vs. Ag/AgCl, the steady‐state base‐current due to the HRP‐catalyzed O₂ reduction was reversibly inhibited by the cyanide injection (200 µL), resulting in peak‐shape current responses. The magnitude of the inhibition peak currents linearly increased with increasing concentrations of cyanide up to 1 µM, and the detection limit was found to be 0.04 µM (S/N=2). The apparent inhibition constant K_i′ was estimated to be 0.87 µM.     

An Amperometric Glucose Biosensor Based on Poly (Pyrrole‐2‐Carboxylic Acid)/Glucose Oxidase Biocomposite

A newly developed amperometric glucose biosensor based on graphite rod (GR) working electrode modified with biocomposite consisting of poly (pyrrole‐2‐carboxylic acid) (PCPy) particles and enzyme glucose oxidase (GOx) was investigated. The PCPy particles were synthesized by chemical oxidative polymerization technique using H₂O₂ as initiator of polymerization reaction and modified covalently with the GOx (PCPy‐GOx) after activation of carboxyl groups located on the particles surface with a mixture of N‐(3‐dimethylaminopropyl)‐N′‐ethylcarbodiimide hydrochloride (EDC) and N‐hydroxysuccinimide (NHS). Then the PCPy‐GOx biocomposite was dispersed in a buffer solution containing a certain amount of bovine serum albumin (BSA). The resulting biocomposite suspension was adsorbed the on GR electrode surface with subsequent solvent airing and chemical cross‐linking of the proteins with glutaraldehyde vapour (GR/PCPy‐GOx). It was determined that the current response of the GR/PCPy‐GOx electrodes to glucose measured at +300 mV vs Cl reference electrode was influenced by the duration of the PCPy particles synthesis, pH of the GOx solution used for the PCPy particles modification and the amount of immobilized PCPy‐GOx biocomposite. An optimal pH of buffer solution for operation of the biosensor was found to be 8.0. Detection limit was determined as 0.039 mmol L⁻¹ according signal to noise ratio (S/N: 3). The proposed glucose biosensor was tested in human serum samples.     

Poly(pyrrole‐co‐pyrrole‐2‐carboxylic acid)/Pyruvate Oxidase Based Biosensor for Phosphate: Determination of the Potential,and Application in Streams

A biosensor based on conductive poly(pyrrole‐co‐pyrrole‐2‐carboxylic acid) [Poly(Py‐co‐PyCOOH)] copolymer film coated gold electrode was developed for the quantitative phosphate determination. Enzyme pyruvate oxidase was immobilized chemically via the functional carboxylated groups of the copolymer. The potential to be applied which is deficiency of phosphate biosensor studies for precise phosphate detection was clarified by using differential pulse voltammetry technique. Performance of the sensing ability of the biosensor was improved by optimizing cofactor/cosubstrate concentrations, polymeric film density and pH. The biosensor showed a linearity up to phosphate concentration of 5 mM, operational stability with a relative standard deviation (RSD) of 0.07 % (n=7) and accuracy of 101 % at ?0.15 V (vs. Ag/AgCl). Detection limit (LOD) and sensitivity were calculated to be 13.3 μM and 5.4 μA mM^?1 cm^?2, respectively by preserving 50 % of its initial response at the end of 30 days. It's performance was tested to determine phosphate concentrations in two streams of Zonguldak City in Turkey. Accuracy of phosphate measurement in stream water was found to be 91 %.