A Nonenzymatic Glucose Sensor Using Nanoporous Platinum Electrodes Prepared by Electrochemical Alloying/Dealloying in a Water‐Insensitive Zinc Chloride‐1‐Ethyl‐3‐Methylimidazolium Chloride Ionic Liquid

We report here a nonenzymatic sensor by using a nanoporous platinum electrode to detect glucose directly. The electrode was fabricated by electrochemical deposition and dissolution of PtZn alloy in zinc chloride‐1‐ethyl‐3‐methylimidazolium chloride (ZnCl₂‐EMIC) ionic liquid. Both SEM and electrochemical studies showed the evidences for the nanoporous characteristics of the as‐prepared Pt electrodes. Amperometric measurements allow observation of the electrochemical oxidation of glucose at 0.4 V (vs. Ag/AgCl) in pH 7.4 phosphate buffer solution. The sensor also demonstrates significant reproducibility in glucose detection; the higher the roughness factor of the Pt electrode, the lower the detection limit of glucose. The interfering species such as ascorbic acid and p‐acetamidophenol can be avoided by using a Pt electrode with a high roughness factor of 151. Overall, the nanoporous Pt electrode is promising for enzymeless detection of glucose at physiological condition.     

Solution infrared spectroelectrochemistry: A review

Infrared (IR) spectroelectrochemical techniques have seen extensive use in studies of electrode surface processes. They have also been employed, albeit less frequently, to investigations of redox species dissolved in solution. The application of IR spectroscopy to electrochemical solution processes represents a special challenge, for absorption of IR radiation by the solvent is a significant interference to detection of vibrational modes of dissolved analytes. It is also difficult to maintain potentiostatic control of the system in specially designed thin-layer spectroelectrochemical cells. Solution IR spectroelectrochemical experiments are important for investigations of redox systems in which it is desired to spectroscopically monitor the structures of dissolved products, intermediates and reactants involved in electrode reactions. Such experiments have been conducted on biochemical, inorganic, organic, and other systems. In this paper some examples of applications of IR spectroelectrochemical studies of solution species in the above areas are presented, and experimental aspects are discussed.     

Electrochemical Detection of Protons Produced in an Electrode Reaction Using Interdigitated Microarray Electrodes

This work describes the use of interdigitated array electrodes (IDAE) for proton detection. Methanol electrooxidation in sulfuric acid solution was exemplified. Reduction currents originating in the reaction product generated by methanol electrooxidation on a Pt generator electrode were observed at the Pt collector electrode, the potential of which was fixed in the hydrogen evolution region. In order to reduce the background current of hydrogen evolution, an Hg‐plated Pt collector electrode was fabricated. Compared to the Pt collector electrode, the reduction current observed at the Hg collector electrode was extremely small. The product detected was found to be a proton from the current responses observed at Pt and Hg collector electrodes.     

Spectroelectrochemical Evaluation of a ZnO Optically Transparent Electrode Prepared by the Spin‐spray Technique

We present a novel zinc oxide (ZnO) optically transparent electrode (OTE) prepared by the spin‐spray technique for spectroelectrochemistry. The spin‐spray technique can deposit ZnO film at a low cost, high rate deposition, and at a low temperature (<100 °C) in a single step. This new technique provides good optical transparency and electrical conductivity for ZnO. The electrochemical and spectroelectrochemical properties of the ZnO electrode were investigated for varying thicknesses of ZnO using methylene blue as a redox indicator. A ZnO OTE chip that includes three electrodes on a glass chip was developed for thin‐layer spectroelectrochemistry. Moreover, the ZnO films were successfully applied in an electrochemical‐localized surface plasmon resonance (LSPR) method for methylene blue detection by using them as a transparent conducting substrate for loading gold nanoparticles.     

Analytical Characteristics of Electrochemical Biosensor Using Pt‐Dispersed Graphene on Boron Doped Diamond Electrode

An electrochemical biosensor was developed using Pt‐nanoparticles (Pt‐NPs) dispersed graphene based on a boron‐doped diamond thin film electrode. To compare its performances with those of other biosensors, glucose was used as a target analyte. This biosensor exhibited a wide linear range, a low detection limit and a higher sensitivity compared to other amperometric biosensors using graphene‐based electrodes. In addition, the biosensor promotes a direct electron transfer between the redox enzymes and the electrode surface and detects low concentration analytes. The excellent performance of the biosensor is attributed to the synergistic effect of the Pt‐NPs, graphene sheet and the BDD thin film. Therefore, it can be a promising application for electrochemical detection of analytes.     

LIGA-electrodes in voltammetric and spectroelectrochemical studies

The advantages of lithographic-galvanic (LIGA) fabricated microstructured honeycomb electrodes are demonstrated for spectroelectrochemical cells with respect to the response time (the time necessary to generate the product in a sufficient layer thickness close to the electrode to be detectable by UV-Vis-NIR spectroscopy) and to the conversion of the redox system in solution under thin-layer conditions. Transmission UV-Vis-NIR spectroscopy for several electrochemical applications can be performed in a special spectroelectrochemical cell based on the LIGA electrode and the two quartz rods, forming the walls of the cell and conducting the light beam through the cell. They are limiting the diffusion layer at the structured part of the working LIGA electrode. These microstructured LIGA-electrodes can be used as well defined models of porous electrodes at which redox processes occur under finite diffusion conditions. Such electrodes have been successfully used in the voltammetric and spectroelectrochemical study of various redox systems in both aqueous and non-aqueous solvents. The possibility to fabricate the well defined microstructures from various organic conducting polymers is demonstrated by the electrochemical deposition of polypyrrole in moulded LIGA-forms at high current densities in aqueous solutions.     

汞修饰掺锡三氧化二铟导电玻璃光透薄层电化学池的设计

报道了汞膜修饰掺锡三氧化二铟导电玻璃电极的制备及其薄层电化学池的设计，测试限电极和薄层的光、电化学性能，在水溶液中，与基底电极相比，该电极的负电位范围增加了７００ｍＶ，并表现出普通汞电极的电化学 性质，以此电极制得的电极制得的薄层层池可适用于氧化还原电位较负的电化学过程的光谱电化学研究及金属离子的电化学分析。     

Investigation of Electrochemical Behavior of Some Dithiophosphonates in Acetonitrile on the Platinum and Gold Electrodes

Some dithiophosphonate derivatives were synthesized and the electrochemical reduction mechanism was investigated by cyclic voltammetry (CV), square wave voltammetry (SWV) and chronoamperometry (CA) in 0.1 M tetrabutylammoniumtetrafluoroborate (TBATFB) in acetonitrile at platinum (Pt) and gold (Au) electrodes. Dithiophosphonates showed a cyclic voltammetric reduction peak at about ?1.1 V at Pt and ?1.3 V at Au electrode (vs. Ag/Ag⁺) in this media. It was also shown that dithiophosphonates can be determined quantitatively in acetonitrile using a calibration graph. The number of electrons transferred were calculated as 2 using ferrocene as a reference compound at the UME electrode. Mechanism of dithiophosphonates was also examined on Pt and Au electrodes and electrochemical reduction of dithiophosphonates seems to follow an EC mechanism with an irreversible electron transfer step. The reaction product in the bulk electrolysis experiment was isolated and identified using proton‐coupled P‐31 NMR, ¹³C‐NMR and IR spectroscopy. The adsorption tests for dithiophosphonates were revealed that no strong or weak adsorption phenomena exist on both Pt and Au electrodes. Simulation curves were acquired by DigiSim 3.03 version to investigate the reduction mechanism and to estimate the kinetic parameters for electrochemical and chemical steps.     

Enhanced Electrocatalytic Activity of Ni‐CNT Nanocomposites for Simultaneous Determination of Epinephrine and Dopamine

A promising electrochemical sensor based nickel‐carbon nanotube (Ni‐CNT) modified on glassy carbon (GC) electrode had been developed and the properties of the modified electrode were characterized by multispectroscopic analysis. The fabricated sensor (GC/Ni‐CNT) electrode was utilized to determine the catecholamines such as epinephrine and dopamine simultaneously. Differential pulse voltammetry and amperometry were used to verify the electrochemical behavior of the studied compounds. The GC/Ni‐CNT based amperometric sensor showed a wide linear range and low detection limit with high analytical sensitivity of 8.31 and 6.61 μA μM^?1 for EP and DA, respectively which demonstrates better characteristics compared to other electrodes reported in the literature. Further, no significant change in amperometric current response was observed in presence of biological interference species such as glucose, cysteine, citric acid, uric acid and ascorbic acid in the detection of EP and DA. The utility of this GC/Ni‐CNT electrode was well established for the determination of EP and DA in human urine samples.     

掺锡三氧化二铟导电玻璃双工作电极薄层光透电化学池的设计

本文报道了ITO导电玻璃双工作电极薄层光透电化学池的设计。这种薄层池具有操作简便,成本低廉的特点,其突出优点在于工作电极的边际效应因采用辅助工作电极而得以明显消除。以Fe(CN)_6~(3-)/(4-)~考察了该池的电化学和光谱吸收响应特性。     

Anodic Oxidation of Serine Anion on Smooth and Platinized Platinum

The anodic oxidation of serine anion on smooth (Pt) and platinized (Pt(Pt)) platinum electrodes is studied by the methods of cyclic and linear voltammetry, rotating disk electrode, coulometry, and reflectance IR spectroscopy. On both electrodes, the potential regions of electrochemical transformation of this amino acid are determined. It is shown that electrooxidation of serine proceeds with abstraction of 4 and 2 electrons on Pt and Pt(Pt) electrodes, respectively. It is found that the anodic oxidation of serine anions proceeds from the adsorbed state; a possible kinetic scheme of this process is proposed.     

Optical fiber spectroelectrochemical device for detection of catechol at press-transferred single-walled carbon nanotubes electrodes

A new long-optical-pathway spectroelectrochemical cell for absorptometric measurements in the UV–Vis region was developed. This cell consists of two optical fibers brought face to face and fixed on the working electrode support. As a proof of concept, the spectroelectrochemical cell was applied to the determination of catechol using a press-transferred single-walled carbon nanotube film as the working electrode. Voltabsorptometry was demonstrated to be very helpful in understanding the mechanism of catechol oxidation. The experiments showed that the main oxidation product is o-benzoquinone, but other soluble side products are also observed. Multivariate calibration explains the selection of 390 nm as the best wavelength for the univariate absorptometric determination of catechol, avoiding the interference of oxidation side products. Catechol was quantified using both the electrochemical and the spectroscopic signal, demonstrating that this hybrid technique is an autovalidated analytical method. Dual detection of catechol was also carried out using amperometric spectroelectrochemistry. Finally, spectroelectrochemistry was used to quantify catechol in the presence of hydroquinone.     

酸性溶液中NaH2PO2在铂电极上氧化的原位红外光谱研究

用SNIFTIRS和循环伏安法研究酸性溶液中次亚磷酸钠在多晶铂电极上的电氧化机理.分析了0.5mol/LH2SO4+0.1mol/LNaH2PO2溶液中原位红外反射谱图与电极电位的关系,发现在发生反应的电位下Pt电极上的吸附物种有氢原子和H2PO2,最终的氧化产物是H3PO4而不是H2PO3-,据此提出了酸性介质中次亚磷酸根离子在Pt上氧化的新机理.     

The Electrochemical Behavior and the Quantitative Determination of Nitrogen Dioxide at a Solid Polymer Electrolyte Supported Pt‐Au Electrode

The electrochemical behavior of NO₂ at Au/Nafion, Pt/Nafion and Pt‐Au/Nafion electrodes was investigated by using electrochemical and SEM methods, respectively. It was found that the Pt‐Au/Nafion electrode showed higher electrocatalytic activity than Pt/Nafion and Au/Nafion electrodes. The net current density of Au/Nafion electrode decayed significantly during the reaction, though it showed high initial value. Pt/Nafion and Pt‐Au/Nafion electrodes, on the contrary, showed good stability. A quantitative determination of NO₂ concentration was carried out at Pt‐Au/Nafion electrode and a satisfactory linear relationship was found for the NO₂ concentration in the range of 0–100 ppm.     

电化学原位步进扫描时间分辨显微镜FTIR反射光谱

结合步进扫描傅立叶变换红外光谱仪和红外显微镜，建立了电化学原位步进扫描时间分辨显微镜FTIR反射光谱.采用微电极和利用纳米结构表面的异常红外效应，显著提高表面吸附物种的红外检测灵敏度和红外电极表面对极化电位的响应速度，使广泛应用的外反射型薄层红外电解池的时间常数(τ=R1Cd)从使用常规盘电极的约40 ms降低到0.65 ms.研究了酸性介质中CO在Pt电极上的吸附过程，谱图的时间分辨率达50 μs.     

超薄层红外光透电解池的设计和应用

采用真空镀膜技术制得了超薄型红外光透极电极，设计了适用于水溶液体系和多种固体电极体系的红外光透薄层电解池，通过亚铁氰化钾水溶液／金电极体系和亚硫酰氯／碳电极体系的现场红外光谱电化学测试证明：该电解池具有结构简单，光谱响应灵敏，适用范围较宽等优点。     

Ordered Mesoporous Silica Incorporating Platinum Nanoparticles as Electrode Material for Paracetamol Detection

High ordered mesoporous materials (SBA-15) modified with Al and/or B and Pt nanoparticles (Pt NPs) were used for preparing modified graphite paste electrodes (Pt/M−SBA-15-GPE, where M=Al−, B− or Al−B−) and applied for paracetamol (PA) detection. The electrodes were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Square wave voltammetry (SWV) technique was used to obtain the analytical parameters for PA detection. The acquired values of electrochemical and analytical parameters recommend the mesoporous compound containing Pt NPs to be used as composite electrode material for PA detection in real samples.     

Effect of Various Deposition Techniques,Electrode Materials and Posttreatment with Tetrabutylammonium and Tetrabutylphosphonium Salts on the Electrochemical Behavior and Stability of Various Prussian Blue Modified Electrodes

The effect of various deposition techniques, electrode materials and posttreatment with tetrabutylammonium and tetrabutylphosphonium salts on the electrochemical behavior and stability of various Prussian blue (PB) modified electrodes, namely PB modified glassy carbon electrodes, silicate‐film supported PB modified glassy carbon electrodes, PB‐doped silicate glassy carbon electrodes, PB modified carbon ceramic electrodes using electrochemical deposition and PB modified carbon ceramic electrodes using chemical deposition is reported. Cyclic voltammetry and amperometric measurements of hydrogen peroxide were performed in a flow injection system while the carrier phosphate buffer (pH 7.0) with a flow rate of 0.8 mL min^?1 was propelled into the electrochemical flow through cell housing the PB modified working electrode as well as an Ag|AgCl|0.1 M KCl reference and a Pt auxiliary electrode. The results showed that the deposition procedure, electrode material and posttreatment with additional chemicals can significantly alter the stability and electrochemical behavior of the PB film. Among the studied PB modified electrodes, those based on carbon ceramic electrodes modified with a film of electropolymerized PB showed the best electrochemical stability.     

Real-time imaging of surface chemical reactions by electrochemical photothermal reflectance microscopy

Traditional electrochemical measurements based on either current or potential responses only present the average contribution of an entire electrode''s surface. Here, we present an electrochemical photothermal reflectance microscope (EPRM) in which a potential-dependent nonlinear photothermal signal is exploited to map an electrochemical process with sub-micron spatial resolution. By using EPRM, we are able to monitor the photothermal signal of a Pt electrode during the electrochemical reaction at an imaging speed of 0.3 s per frame. The potential-dependent photothermal signal, which is sensitive to the free electron density, clearly revealed the evolution of surface species on the Pt surface. Our results agreed well with the reported spectroelectrochemical techniques under similar conditions but with a much faster imaging speed. We further mapped the potential oscillation during the oxidation of formic acid on the Pt surface. The photothermal images from the Pt electrode well matched the potential change. This technique opens new prospects for real-time imaging of surface chemical reaction to reveal the heterogeneity of electrochemical reactivity, which enables broad applications to the study of catalysis, energy storage, and light harvest systems.

The potential-dependent photothermal signal, which is sensitive to the free electron density, map the evolution of surface species on the electrode in real time.     

中性介质中L-丝氨酸在Pt电极上解离吸附和氧化的原位FTIR研究

运用电化学循环伏安(CV)和原位红外反射光谱(in situ FTIRS)研究了中性介质中L-丝氨酸在Pt电极上的解离吸附和氧化过程. 结果表明, 在中性溶液中, 以两性离子形式存在的丝氨酸可以在很低的电位下(-0.6 V, vs. SCE)在Pt电极表面发生解离吸附, 生成强吸物种一氧化碳(COL)、(COB)和氰负离子(CN-). 研究结果还表明, 当电位低于0.7 V(vs. SCE)时, CN-能稳定存在于电极表面, 抑制丝氨酸的进一步反应. 在更高电位时则主要为丝氨酸分子的氧化过程.