Electrochemical Characterization and Determination of Mercury Using Carbon Paste Electrodes Modified with Cyclodextrins

In this work the characterization and determination of mercury in HClO₄ media using carbon paste electrodes modified with α‐ and β‐cyclodextrins (CPE_α‐CD and CPE_β‐CD) at E_d=?0.7 V with a t_d = 20 s and a potential scan v=20 mV s^?1 is studied‥ The statistical results obtained indicate that the modified electrodes displayed a better analytical performance as compared to that obtained with the unmodified CPE. The detection limits for the CPE_α‐CD and for the CPE_β‐CD were 0.05 and 0.09 μM, respectively, while for the CPE it was 0.41 μM. The CPE_β‐CD exhibited greater sensitivity as compared to that of the CPE_α‐CD.     

Electrochemical Characteristics and Electrosensing of an Antiviral Drug,Entecavir via Synergic Effect of Graphene Oxide Nanoribbons and Ceria Nanorods

A sensitive electrochemical sensor was fabricated based on ceria‐graphene oxide nanoribbons composite (CeO₂‐GONRs) for an antiviral drug, entecavir (ETV). It was characterized by SEM, EDAX, AFM, IR and Raman spectroscopic techniques. The electrochemical behaviour of ETV was investigated by cyclic voltammetric, differential pulse voltammetric (DPV), linear sweep voltammetric (LSV) and square wave voltammetric (SWV) methods at CeO₂‐GONRs modified glassy carbon electrode. Good linearity was observed between the peak current and concentration of ETV in the range of 0.51 ‐ 100 μM with a detection limit of 0.042 μM in DPV method, 2.1 – 61.1 μM with a detection limit of 0.7 μM in LSV method and 0.1 ‐ 80 μM with a detection limit of 68.1 nM in SWV method. The proposed sensitive DPV method was successfully applied for the determination ETV in tablets and biological samples.     

Electrocatalytic Oxidation and Sensitive Determination of Paracetamol Based on Nanosheets Self‐assembled Lindgrenite Microflowers

In this work, the nanosheet‐assembled lindgrenite microflowers (chemical formula: Cu₃Mo₂O₉) were synthesised through a simple process and low‐cost raw materials at room temperature in aqueous solution without using any surface‐active agent. The tightly interlaced nanosheets, like petals, can increase the specific surface area, which can bring about higher electrocatalytic activity and electroanalysis sensitivity. Thus, lindgrenite microflowers were prepared as an electrochemical sensor and successfully applied in the detection of paracetamol through the modified glass carbon electrode. Furthermore, this electrochemical reaction process was simulated at the ab‐initio level to reveal the catalytic mechanism, and the simulation results agreed well with electrochemical experiments. The electrochemical performance of the lindgrenite microflowers modified glassy carbon electrode (GCE) was studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The linearity of paracetamol ranged from 0.05 to 1200 μM (IT method) and 0.05 to 1000 μM (DPV method), low detection limit (0.01 μM) and high sensitivity (5.11 mA mM^?1 cm^?2) towards paracetamol. Moreover, this sensor was applied to detect paracetamol in human blood serum samples. The excellent results demonstrated that the prepared electrode not only showed a desirable linear range towards paracetamol but also exhibited practical applicability and reliability towards human serum samples detection.     

Non‐enzymatic Fructose Sensor Based on Co3O4 Thin Film

In this study, we report on the selective of fructose on Co₃O₄ thin film electrode surface. A facile chemical solution deposition technique was used to fabricate Co₃O₄ thin film on fluorine doped tin oxide, FTO, glass. Electrode characterization was done using XRD, HRTEM, SEM, AFM, and EIS. The constructed sensor exhibited two distinctive linear ranges (0.021–1.74 mM; 1.74–∼15 mM) covering a wide linear range of up to ∼15 mM at an applied potential of +0.6 V vs Ag/AgCl in 0.1 M NaOH solution. The sensor demonstrated high, reproducible and repeatable (R.S.D of <5 %) sensitivity of 495 (lower concentration range) & 53 (higher concentration range) μA cm⁻² mM⁻¹. The sensor produced a low detection limit of ∼1.7 μM (S/N =3). The electrode was characterised by a fast response time of <6 s and long term stability. The repeatability and stability of the electrode resulted from the chemical stability of Co₃O₄ thin film. The sensor was highly selective towards fructose compared to the presence of other key interferences i. e. AA, AC, UA. The ease of the electrode fabrication coupled with good electrochemical activity makes Co₃O₄ thin film, a promising candidate for non‐enzymatic fructose detection.     

Voltammetric Determination of 4‐Nitrophenol and 5‐Nitrobenzimidazole Using Different Types of Silver Solid Amalgam Electrodes – A Comparative Study

The voltammetric behavior of two genotoxic nitro compounds (4‐nitrophenol and 5‐nitrobenzimidazole) has been investigated using direct current voltammetry (DCV) and differential pulse voltammetry (DPV) at a polished silver solid amalgam electrode (p‐AgSAE), a mercury meniscus modified silver solid amalgam electrode (m‐AgSAE), and a mercury film modified silver solid amalgam electrode (MF‐AgSAE). The optimum conditions have been evaluated for their determination in Britton‐Robinson buffer solutions. The limit of quantification (L_Q) for 5‐nitrobenzimidazole at p‐AgSAE was 0.77 µmol L^?1 (DCV) and 0.47 µmol L^?1 (DPV), at m‐AgSAE it was 0.32 µmol L^?1 (DCV) and 0.16 µmol L^?1 (DPV), and at MF‐AgSAE it was 0.97 µmol L^?1 (DCV) and 0.70 µmol L^?1 (DPV). For 4‐nitrophenol at p‐AgSAE, L_Q was 0.37 µmol L^?1 (DCV) and 0.32 µmol L^?1 (DPV), at m‐AgSAE it was 0.14 µmol L^?1 (DCV) and 0.1 µmol L^?1 (DPV), and at MF‐AgSAE, it was 0.87 µmol L^?1 (DCV) and 0.37 µmol L^?1 (DPV). Thorough comparative studies have shown that m‐AgSAE is the best sensor for voltammetric determination of the two model genotoxic compounds because it gives the lowest L_Q, is easier to prepare, and its surface can be easily renewed both chemically (by new amalgamation) and/or electrochemically (by imposition of cleaning pulses). The practical applicability of the newly developed methods was verified on model samples of drinking water.     

Voltammetric Determination of 4‐Nitrophenol Using a Novel Type of Silver Amalgam Paste Electrode

A differential pulse voltammetric (DPV) method was developed for the determination of 4‐nitrophenol (4‐NP) at a newly developed silver amalgam paste electrode (AgA‐PE) in Britton–Robinson buffer pH 3.0. The electrode is based on a disposable plastic pipette tip filled with paste amalgam based on a mixture of mercury and fine silver powder (9 : 1, w/w). The experimental parameters, such as pH of Britton–Robinson buffer and activation and regeneration potential of the electrode surface were optimized. The reduction peak current dependences were linear for the concentration of 4‐NP from 0.2 to 100 μM. The method showed reproducible results with RSD (n=45) of 1.7%. The limit of determination (LOD) was 0.3 μM. The method was successfully applied for the direct determination of 4‐NP in drinking water.     

Rapid and Selective Determination of Vanillin in the Presence of Caffeine,its Electrochemical Behavior on an Au Electrode Electropolymerized with 3‐Amino‐1,2,4‐triazole‐5‐thiol

Electrochemical oxidation of vanillin (VAN) in the presence of caffeine (CAF) was studied on a gold (Au) electrode modified with 3‐amino‐1,2,4‐triazole‐5‐thiol (ATT) film by using differential pulse voltammetry (DPV) and cyclic voltammetry (CV) method. The formation of the ATT film on the Au electrode surface was characterized by the CV, fourier transform infrared spectroscopy (FTIR) and impedance spectroscopy (EIS) methods. A single irreversible oxidation peak of the VAN was obtained by using the CV method. The determination of VAN in the presence of CAF was carried out at pH 4 in Britton Robinson buffer (BR) by the DPV method. Under the optimal conditions, the oxidation peak current was proportional to the concentration of VAN in the range of 1.1 μM to 76.4 μM in the presence of CAF with the correlation coefficient of 0.997 and the detection limit of 0.19 μM (S/N=3). The selective determination of VAN in a commercial coffee sample was carried out with satisfactory results on the ATT‐Au modified electrode.     

Screen‐printed Electrode Modified with ZnFe2O4 Nanoparticles for Detection of Acetylcholine

In this paper a sensor to detect acetylcholine on the basis of ZnFe₂O₄ nanoparticles modified screen printed electrode (SPE) is reported. In the range 0.08–500.0 μM, with the detection limit of 0.024±0.001 μM, acquired anodic peak currents where shown to be linearly dependent on acetylcholine concentrations by differential pulse voltammetry (DPV). It was proven that acetylcholine oxidation at adjusted electrode surface takes place at 100 mV potential less positive compared to an unadjusted screen printed electrode. The electron transfer coefficient (α=0.51) and diffusion coefficient (D=9.3×10^?6 cm²/s) of acetylcholine oxidation were determined too. In addition, this original sensor possesses numerous benefits such as reproducibility, high stability and rapid response (20 s).     

Graphene Functionalized Graphite Electrode with Diphenylacetylene for Sensitive Electrochemical Determination of Adenosine‐5′‐triphosphate

In this paper a molecular wire modified carbon paste electrode (MW‐CPE) was firstly prepared by mixing graphite powder with diphenylacetylene (DPA). Then a graphene (GR) and chitosan (CTS) composite film was further modified on the surface of MW‐CPE to receive the graphene functionalized electrode (CTS‐GR/MW‐CPE), which was used for the sensitive electrochemical detection of adenosine‐5′‐triphosphate (ATP). The CTS‐GR/MW‐CPE exhibited excellent electrochemical performance and the electrochemical behavior of ATP on the CTS‐GR/MW‐CPE was carefully studied by cyclic voltammetry with an irreversible oxidation peak appearing at 1.369 V (vs. SCE). The electrochemical parameters such as charge transfer coefficient (α) and electrode reaction standard rate constant (k_s) were calculated with the results of 0.53 and 5.28×10^?6 s^?1, respectively. By using differential pulse voltammetry (DPV) as detection technique, the oxidation peak current showed good linear relationship with ATP concentration in the range from 1.0 nM to 700.0 µM with a detection limit of 0.342 nM (3σ). The common coexisting substances, such as uric acid, ascorbic acid and guanosine‐5′‐triphosphate (GTP), showed no interferences and the modified electrode was successfully applied to injection sample detection.     

Synthesis of Ferrocene Based Naphthoquinones and its Application as Novel Non‐enzymatic Hydrogen Peroxide

At present, a highly sensitive hydrogen peroxide (H₂O₂) sensor is fabricated by ferrocene based naphthaquinone derivatives as 2,3‐Diferrocenyl‐1,4‐naphthoquinone and 2‐bromo‐3‐ferrocenyl‐1,4‐naphthoquinone. These ferrocene based naphthaquinone derivatives are characterized by H‐NMR and C‐NMR. The electrochemical properties of these ferrocene based naphthaquinone are investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) on modified glassy carbon electrode (GCE). The modified electrode with ferrocene based naphthaquinone derivatives exhibits an improved voltammetric response to the H₂O₂ redox reaction. 2‐bromo‐3‐ferrocenyl‐1,4‐naphthoquinone show excellent non‐enzymatic sensing ability towards H₂O₂ response with a detection limitation of 2.7 μmol/L a wide detection range from 10 μM to 400 μM in H₂O₂ detection. The sensor also exhibits short response time (1 s) and good sensitivity of 71.4 μA mM^?1 cm^?2 and stability. Furthermore, the DPV method exhibited very high sensitivity (18999 μA mM^?1 cm^?2) and low detection limit (0.66 μM) compared to the CA method. Ferrocene based naphthaquinone derivative based sensors have a lower cost and high stability. Thus, this novel non‐enzyme sensor has potential application in H₂O₂ detection.     

Challenge Approach of an Inexpensive Electrochemical Sensor for Rapid Selective Determination of two Non‐classical β‐Lactams in Presence of Different Degradants and Interference Substances

An inexpensive stability−indicating anodic voltammetric method for rapid determination of two non‐classical β ‐lactam antibiotics; Meropenem (MP) and Ertapenem (EP) has been developed and validated. The method was based on the enhancement of voltammetric response at a disposable graphite pencil electrode (GPE). Differential pulse voltammetric (DPV) method was developed for quantification of both drugs in B−R buffer solution (pH 2.0) at GPE. The GPE displayed very good voltammetric behavior with significant enhancement of the peak current compared to glassy carbon electrode (GCE). Stress stability studies were performed using 0.5 M of either HCl or NaOH and H₂O₂. Mass and infrared spectroscopy were used for identification of degradants and their pathways were illustrated. Under optimal conditions, the peak currents showed a linear dependence with drug concentrations. The achieved limits of detection (LOD) were 1.23, 2.07 and 1.50 μM for MP and two waves of EP, respectively. The developed voltammetric method was successfully applied for direct determination of MP and EP in drug substances, pharmaceutical vials and in presence of either their corresponding hydrolytic, oxidative‐degradants or interfering substances with no potential interferences. The differential pulse voltammograms were highly advantageous and applicable in QC laboratories for rapid, selective micro‐determination of MP and EP.     

Highly Sensitive Temperature‐responsive Sensor Based on PS‐PDEA‐PS/C60‐MWCNTs for Reversible Switch Detection of Catechol

A new type of temperature‐responsive electrochemical sensor was constructed based on a glass carbon electrode modified by the composite containing temperature‐responsive polymer polystyrene‐poly N, N‐diethyl acrylamide‐polystyrene (PS‐PDEA‐PS) and fullerenes‐carboxylate multi‐walled carbon nanotubes (C₆₀‐MWCNTs). The sensor was used for the electrochemical detection of catechol (CC). When the temperature is higher than the critical temperature (LCST) of PS‐PDEA‐PS, the electrochemical behavior of CC can be detected, which it is in the “on” state. When the temperature is lower than LCST, the composite modified film is in the “off” state and the electrochemical behavior of CC was not detected. Under the best experimental conditions, the sensor has a good detection range for catechol from 4.0 to 135.0 μM, with a LOD of 1.45 μM. In addition, the proposed sensor has good stability and reproducibility, and was successfully applied to the determination of catechol in real tap water.     

Electro-deposition of gold nanostructures on carbon paste electrode: a platform with signal amplification for voltammetric study and determination of pyridoxine (vitamin B<Subscript>6</Subscript>)

For the first time, the electrochemical synthesis of gold nanostructures was done at the surface of carbon paste electrode. This device was used as a simple and sensitive electrochemical sensor for measurement of pyridoxine (Vitamin B₆, VB₆). The diffusion coefficient (D) and the kinetic parameters such as electron transfer coefficient (α) and catalytic rate constant (k) for VB₆ were also determined using electrochemical approaches. The cyclic voltammetry method showed VB₆ oxidation reaction with irreversible characteristics was diffusion-controlled at low scan rates. Using differential pulse voltammetry (DPV), the peak current was linearly dependent on VB₆ concentration in the ranges of 1.9–110.8 and 110.8–257.0 μM, with detection limit of 74.0 nM, respectively. Results showed there is no interference of other vitamins in oxidation of VB₆. DPV was used to quantify of VB₆ in some real samples by the standard addition method. The modified electrode showed good sensitivity and stability.     

Application of the Bismuth Film Electrode for Voltammetric Determination of Titanium Using Ti(IV)‐Oxalate‐Chlorate Catalytic System

The catalytic voltammetric protocol for the determination of titanium at a bismuth film electrode is presented. The method is based on the reduction of the Ti(IV)‐oxalate complex to Ti(III)‐oxalate in an acidic solution. It was proven that the addition of KClO₃ causes rapid oxidation of Ti(III)‐oxalate and, subsequently, an increase of the reduction peak current of Ti(IV) at the bismuth film electrode. Parameters that influence the Ti response, including the film preparation, solution pH, oxalate acid and chlorate concentrations, were optimized. The exploitation of the bismuth film electrode under the optimized conditions yielded a stable response for titanium, with high sensitivity (12.5 μA μM^?1), good precision (RSD=5.0%) and a low detection limit (1×10^?8 M).     

Selective Voltammetric Detection of Uric Acid in the Presence of Ascorbic Acid at Well‐Aligned Carbon Nanotube Electrode

The voltammetric behaviors of uric acid (UA) and L ‐ascorbic acid (L ‐AA) were studied at well‐aligned carbon nanotube electrode. Compared to glassy carbon, carbon nanotube electrode catalyzes oxidation of UA and L ‐AA, reducing the overpotentials by about 0.028 V and 0.416 V, respectively. Based on its differential catalytic function toward the oxidation of UA and L ‐AA, the carbon nanotube electrode resolved the overlapping voltammetric response of UA and L ‐AA into two well‐defined voltammetric peaks in applying both cyclic voltammetry (CV) and differential pulse voltammetry (DPV), which can be used for a selective determination of UA in the presence of L ‐AA. The peak current obtained from DPV was linearly dependent on the UA concentration in the range of 0.2 μM to 80 μM with a correlation coefficient of 0.997. The detection limit (3δ) for UA was found to be 0.1 μM. Finally, the carbon nanotube electrode was successfully demonstrated as a electrochemical sensor to the determination of UA in human urine samples by simple dilution without further pretreatment.     

Nanomolar Determination of Methyldopa in the Presence of Large Amounts of Hydrochlorothiazide Using a Carbon Paste Electrode Modified with Graphene Oxide Nanosheets and 3‐(4′‐Amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic Acid

A novel electrochemical sensor for sensitive detection of methyldopa at physiological pH was developed by the bulk modification of carbon paste electrode (CPE) with graphene oxide nanosheets and 3‐(4′‐amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic acid (3,′AA). Applying square wave voltammetry (SWV), in phosphate buffer solution (PBS) of pH 7.0, the oxidation current increased linearly with two concentration intervals of methyldopa, one is 1.0×10^?8–1.0×10^?6 M and the other is 1.0×10^?6–4.5×10^?5 M. The detection limit (3σ) obtained by SWV was 9.0 nM. The modified electrode was successfully applied for simultaneous determination of methyldopa and hydrochlorothiazide. Finally, the proposed method was applied to the determination of methyldopa and hydrochlorothiazide in some real samples.     

Development of a Creatinine Sensor Based on a Molecularly Imprinted Polymer‐Modified Sol‐Gel Film on Graphite Electrode

An electrochemical creatinine sensor based on a molecularly imprinted polymer (MIP)‐modified sol‐gel film on graphite electrode was developed. The surface coating of MIP over sol‐gel was advantageous to obtain a porous film with outwardly exposed MIP cavities for unhindered selective rebinding of creatinine from aqueous and biological samples. A fast differential pulse, cathodic stripping voltammetric response of creatinine can be obtained after being preanodized the sensor in neutral medium containing appropriate amount of creatinine at +1.8 V versus SCE for 120 s. A linear response over creatinine concentration in the range of 1.23 to 100 μg mL^?1 was exhibited with a detection limit of 0.37 μg mL^?1 (S/N=3).     

Electrodeposition of Silver Amalgam on Thin Gold Film Electrodes for Voltammetric Detection of 4‐Nitrophenol and DNA Labeled with Osmium Tetroxide‐Bipyridine Complex

Alternative electrode materials suitable to prepare novel working electrode applicable in detecting biopolymers such as nucleic acids, proteins or glycoproteins, represent a significant contribution to bio‐electroanalysis. Herein, electrodes made of vapor‐deposited thin gold films (vAuE) were used as an alternative substrate for the electrodeposition of silver amalgam particles (AgAPs), next to indium tin oxide and pyrolytic graphite, which are already used. The conditions and parameters of double pulse chronoamperometry were optimized for the most‐sensitive voltammetric detection of 4‐nitrophenol (4‐NP). The resulting electrodes were characterized by scanning electron microscope with energy dispersive X‐ray spectroscopy. While 4‐NP could not be detected by bare nonactivated vAuEs at all, their electrochemical activation offered a limit of detection (LoD) of 25 and 5 μmol.l^?1 by means of CV and DPV, respectively. AgAP electrodeposited on vAuE, offered 2.5‐times lower LoDs 10 μmol.l^?1 by CV and comparable LoD 5 μmol.l^?1 by DPV. Advantageously, AgAPs could be repeatedly deposited on and anodically dissolved from the vAuE with a relative standard deviation 13 % of the ten‐times repeated DPV signal of 4‐NP (100 μmol.l^?1). In comparison to vAuE, the vAuE‐AgAP offered about 400 mV broader potential window, which allowed detection of single strand DNA fragment labeled by osmium tetroxide?bipyridine complex down to 2 ng.μl^?1 by means of DPV.     

Detection of Dexamethasone Sodium Phosphate in Blood Plasma: Application of Hematite in Electrochemical Sensors

We studied sensor application of a graphene oxide and hematite (α‐Fe₂O₃/GO) composite electrode well‐characterized by the SEM and XRD. Through differential pulse voltammetry (DPV), oxidation of dexamethasone sodium phosphate (DSP) was studied at the surface of a glassy carbon electrode (GCE) modified with graphene oxide nanosheets (GO) and the α‐Fe₂O₃/GO composite. The values of the transfer coefficient (α) and the diffusion coefficient (D) of DSP were 0.5961 and 4.71×10^?5 cm² s^?1 respectively. In the linear range of 0.1–50 μM, the detection limit (DL) was 0.076 μM. In the second step, a GCE was modified with α‐Fe₂O₃/GO composite and the DSP measurement step was repeated to analyzed and compare the effects of hematite nanoparticles present on graphene oxide surfaces. According to the results, α and D were 0.52 and 2.406×10^?4 cm² s^?1 respectively and the DL was 0.046 μM in the linear range of 0.1–10.0 μM. The sensor is simple, inexpensive and uses blood serum.     

A NADH Sensor Based on 1,2‐Naphththoquinone Electropolymerized on Multi‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

A new carbon nanotubes modified electrode (poly‐Nq‐MWCNTs/GCE) was fabricated by electropolymerization of 1,2‐naphththoquinone to the surface of multi‐walled carbon nanotubes modified electrode by casting method. The morphology of the nanocomposite was characterized by scanning electron microscopy. Cyclic voltammetry and chronoamperometry were applied to investigate the electrochemical properties of the poly‐Nq‐MWCNTs nanocomposite modified electrode. The result of electrochemical experiments showed that such modified electrode had a favorable catalytic ability to oxidation of β‐nicotinamide adenine dinucleotide (NADH). The resulted sensor was sensitiveness to NADH and achieved 95β of the steady‐state current within 5s. Furthermore, the anodic peak current was linear to the concentration of NADH for the range from 1.0 μM to 0.14 mM. The linear equation was: I(μA) = 0.3987 + 0.1035c (μmol/L), the correlation coefficient r = 0.9962, the detect limit is down to 1 × 10^?7 M (S/N = 3) and the sensitivity is 0.1035 μA/mmol. The well catalytic activity of the sensor was ascribed to the synergistic effect role played by MWCNTs and poly‐Nq. Moreover, the based sensor possesses good stability and reproducibility.