An automated FTIR method for the routine quantitative determination of moisture in lubricants: An alternative to Karl Fischer titration

An accurate primary Fourier transform infrared (FTIR) method for the determination of moisture in mineral and ester based lubricants has been developed based on the extraction of moisture into dry acetonitrile. FTIR evaluation of acetonitrile extracts from new and used lubricants as well as common lubricant additives and contaminants which might co-extract indicated that phenolic constituents interfered significantly with moisture measurements. By measuring moisture at 3676 cm⁻¹ on the shoulder of the asymmetric OH stretching band, spectral interferences from extracted phenolic constituents were minimized. The spectra of calibration standards (0-2100 ppm), prepared by gravimetric addition of water to dry acetonitrile, were recorded in a 1000-μm CaF₂ transmission flow cell and produced linear standard curves having an S.D. of ∼±20 ppm. Lubricant sample preparation involved the vigorous shaking (20 min) of a 1:1.5 (w/v) mixture of lubricant and dry acetonitrile, centrifugation to separate the phases, acquisition of the FTIR spectrum of the upper acetonitrile layer, and subtraction of the spectrum of the dry acetonitrile used for extraction. A Continuous Oil Analyzer and Treatment (COAT^®) FTIR system was programmed to allow the automated analysis of acetonitrile extracts, and the methodology was validated by analyzing 58 new and used oils, independently analyzed by the Karl Fischer (KF) method. Linear regression of FTIR versus KF results for these oils produced a linear plot with a between-method S.D. of ±80 ppm. As implemented on the COAT^® system, this FTIR method is capable of analyzing 72 acetonitrile extracts/h and provides a high-speed alternative to the KF titrimetric procedures for the determination of water in lubricants.     

Modelling relation between oxidation resistance and tribological properties of non-toxic lubricants with the use of artificial neural networks

The lubricants based on vegetable oils, as environmental friendly, are urgently sought. However, in addition to ecological characteristics, the lubricating properties have to be met. To meet these requirements the active additives influencing the lubricating properties and oxidation resistance are used. The useful lifetime of lubricants is determined largely by their abilities to resist oxidation. The article presented the results of new, ecological lubricants development. The oxidation performances of different developed lubricants have been tested. The experimentally determined oxidation stability of the compositions based on vegetable oils are presented. Analysed oxidation onset temperature was obtained from the differential scanning calorimetry (DSC) curves, which provides the rapid prediction of the oxidative stability of lubricants. Besides the lubricating composition based on vegetable oils, the developed greases-based mineral, or synthetic oil were investigated. The properties of these greases were evaluated using the measurement of parameters describing structure (penetration) and resistance to high temperature (dropping point). The lubricating properties of both the greases and vegetable oil compositions were tested on four-ball testing machine. In the results of the modelling of the lubricating properties the neural network models for the both types of the lubricants were developed. A discussion of the research results and analysis of models validity is given below. The experimental results are compared with the calculated using the neural models. An acceptable agreement was achieved.     

Stoichiometric determination of moisture in edible oils by Mid-FTIR spectroscopy

A simple and accurate method for the determination of moisture in edible oils by differential FTIR spectroscopy has been devised based on the stoichiometric reaction of the moisture in oil with toluenesulfonyl isocyanate (TSI) to produce CO₂. Calibration standards were devised by gravimetrically spiking dry dioxane with water, followed by the addition of neat TSI and examination of the differential spectra relative to the dry dioxane. In the method, CO₂ peak area changes are measured at 2335 cm⁻¹ and were shown to be related to the amount of moisture added, with any CO₂ inherent to residual moisture in the dry dioxane subtracted ratioed out. CO₂ volatility issues were determined to be minimal, with the overall SD of dioxane calibrations being ∼18 ppm over a range of 0–1000 ppm. Gravimetrically blended dry and water-saturated oils analysed in a similar manner produced linear CO₂ responses with SD's of <15 ppm on average. One set of dry–wet blends was analysed in duplicate by FTIR and by two independent laboratories using coulometric Karl Fischer (KF) procedures. All 3 methods produced highly linear moisture relationships with SD's of 7, 16 and 28 ppm, respectively over a range of 200–1500 ppm. Although the absolute moisture values obtained by each method did not exactly coincide, each tracked the expected moisture changes proportionately. The FTIR_TSI-H2O method provides a simple and accurate instrumental means of determining moisture in oils rivaling the accuracy and specificity of standard KF procedures and has the potential to be automated. It could also be applied to other hydrophobic matrices and possibly evolve into a more generalized method, if combined with polar aprotic solvent extraction.     

Comparative study of the oxidative and thermal stability of vegetable oils to be used as lubricant bases

Demand for lubricating oils is increasing in the growing Brazilian economy. The use of vegetable bases in exchange of minerals can bring socio-economic and environmental benefits for Brazil. The purpose of this study is to compare the thermal and oxidative stability of vegetable oils related to the bases commonly used as lubricants. In this study, thermogravimetric analysis of castor oil, cotton oil, macauba’s almond oil, passion oil, paraffinic mineral oil, naphthenic oil (NH-140) and synthetic oil (Etro) was performed in inert and oxidative atmosphere to study the thermal and oxidative degradation of the vegetable oils related to the most common lubricants’ oils base. These oils’ oxidation stability were determined by standard procedures (ISO 6886). The use of mineral oil’s additives in these vegetable oils was tested to verify the viability of these additives to improve the oxidative stability of the vegetable oils. The castor oil and the cotton oil presented results of thermal analysis similar to the mineral and synthetic bases values. The castor oil was the only vegetable oil that showed a great oxidative stability. All other vegetable oils had their oxidative stability significantly increased by the additives.     

Determination of Esters in Motor and Industrial Oils by IR Spectrometry

IR spectra of mixtures of mineral oil and isopropyl myristate modeling motor oils with different concentrations of esters were studied. A relationship between the absorption band intensities at 1737, 1180, and 1110 cm⁻¹ and the ester concentration in the oil was revealed. A procedure was proposed for the determination of esters in motor oils by IR spectrometry (c _min = 1%; RSD ≤ 8.6%). The procedure was tested on several commercially available samples of lubricants (RSD ≤ 12%).__________Translated from Zhurnal Analiticheskoi Khimii, Vol. 60, No. 8, 2005, pp. 811–814.Original Russian Text Copyright © 2005 by Gol’eva, Rudnev, Pisanov.     

Reduction in the moisture absorption of cured MY720/DDS epoxy resins

Thin films of cured MY720/DDS epoxy resins were treated with blocking reagents for hydroxyl, amine, and epoxide functional groups. Infrared spectroscopy (IR) and differential scanning calorimetry (DSC) were used to monitor the progress of the reaction. Treated films were soaked in distilled water at 30°C for 720 h, and the corresponding moisture absorption determined gravimetrically. Samples treated with N-methyl-N-t-butyldimethylsilyl trifluroacetamide (MTBSTFA) containing 1% t-butyldimethylchlorosilane (TBDMCS) in dimethylsulfoxide (DMSO) at 30°C showed a maximum reduction in the IR peak at 3400 cm^?1 (OH and NH) of 39% and a 100% reduction in the epoxide peak at 904 cm, ^?1. The moisture absorption was 1.9%, a reduction of 58% compared to the untreated films (ca. 4.5%). The reactions show dependencies on time and temperature and are diffusion controlled. Samples treated with trimethylsilyl isocyanate (TMSI) in DMSO a 70°C showed 72% reduction in the 3400 cm^?1 IR peak; DSC thermograms do not show an exothermic energy, suggesting that all epoxide groups reacted. These reactions are primarily dependent on time and temperature. The moisture absorption of TMSI treated samples was 1.0% (75% reduction). Samples were also treated with m-trifluoromethyl phenyliscyanate (MTFPI). The reduction in the IR peak at 3400 cm^?1 was 9%, but the moisture absorption was 2.4%—a reduction of 47%.     

Multiresidue analytical method for the determination of antimicrobials, preservatives, benzotriazole UV stabilizers, flame retardants and plasticizers in fish using ultra high performance liquid chromatography coupled with tandem mass spectrometry

A multiresidue analytical method for the determination of emerging pollutants belonging to personal care products (PCPs) (antimicrobials, preservatives), benzotriazole UV stabilizers (BUVSs) and organophosphorus compounds (OPCs) in fish has been developed using high speed solvent extraction (HSSE) followed by silica gel clean up and ultra fast liquid chromatography coupled with tandem mass spectrometry (UFLC–MS/MS) analysis. Developed extraction and clean up method yielded good recovery (>70%) for all the four groups of emerging pollutants, i.e. antimicrobials (78.5–85.6%), preservatives (85.0–89.4%), BUVSs (70.9–112%) and OPCs (81.6–114%; except for TEP – 68.9% and TPeP – 58.1%) with RSDs ranging from 0.7 to 15.4%. Intra- and inter-day repeatabilities were less than 19.8% and 19.0%, respectively at three spiked levels. The concentrations were given in lipid weight (lw) basis, and the method detection limits were achieved in the lowest range of 0.001–0.006 ng g⁻¹ for two antimicrobials, 0.001–0.015 ng g⁻¹ for four preservatives, 0.0002–0.009 ng g⁻¹ for eight BUVSs and 0.001–0.014 ng g⁻¹ for nine OPCs. Finally, the method was successfully validated as a simple and fast extraction method for the determination of 23 compounds belonging to PCPs, BUVSs and OPCs and applied to the analysis of three species of fish from Manila Bay, the Philippines. Concentrations ranged from 27 to 278 ng g⁻¹ for antimicrobials, 6.61 to 1580 ng g⁻¹ for paraben preservatives, −1 for BUVSs and ND (not detected) to 266 ng g⁻¹ for OPCs suggesting the ubiquitous contamination by these emerging pollutants in Manila Bay. This is the first method developed for the determination of triclocarban, four paraben preservatives and four BUVSs, in fish.     

Mass spectrometry molecular fingerprinting of mineral and synthetic lubricant oils

The molecular composition of lubricating oils has a strong impact on how automotive engines function, but the techniques used to monitor the quality parameters of these oils only inspect their gross physical–chemical properties such as viscosity, color, and bulk spectroscopy profiles; hence, bad-quality, adulterated, or counterfeit oils are hard to detect. Herein, we investigated the ability of direct infusion electrospray ionization mass spectrometry (ESI-MS) to provide simple, rapid but characteristic fingerprint profiles for such oils of the mineral and synthetic types. After a simple aqueous extraction, ESI-MS analyses, particularly in the positive ion mode, did indeed show characteristic molecular markers with unique profiles, which were confirmed and more clearly visualized by partial least squares-discriminant analysis (PLS-DA). Nuclear magnetic resonance and Fourier transform infrared-attenuated total reflection spectroscopy were also tested for the bulk samples but showed nearly identical spectra, thus failing to reveal their distinct molecular composition and to differentiate the oil samples. To simulate adulteration, mixtures of mineral and synthetic oils were also analyzed by ESI(+)-MS, and additions as low as 1% of mineral oil to synthetic oil could be detected. The technique therefore offers a simple and fast but powerful tool to monitor the molecular composition of lubricant oils, particularly vias their more polar constituents.     

Determination of oxidation products in transformer oils using FT-IR spectroscopy

Transformer oils are subject to a lot of control checks in the process of their exploitation, because the presence of oxidized products causes damages in the electrical equipment. In the process of exploitation of transformer oils anti-oxidation additives get exhausted and products of oxidation are formed. This paper describes the development method for study of oxidation transformer oils by Fourier transform infrared (FT-IR) spectroscopy. The aim of this paper is to determine the main products of oxidation of transformer oils and to increase the sensitivity of FT-IR analysis by the extraction method. The method which we suggest to register all oxidized products is of great interest. The problem is the detection limit of routine apparatus. For this reason we have developed an extraction method, which can identify precisely all oxidized products qualitatively and quantitatively in the region 1800-1650 cm⁻¹. Thus a manifold increase of the FT-IR analysis is achieved, combined with increased sensitivity, precision and the possibilities for registering micro-amounts otherwise beyond the routine technique. FT-IR spectroscopy is a powerful method with great practical significance for investigation of carbonyl- and carboxylic degradation products from transformer oils.     

Hollow fiber liquid phase microextraction as a preconcentration and clean-up step after pressurized hot water extraction for the determination of non-steroidal anti-inflammatory drugs in sewage sludge

A method for the quantitative determination of non-steroidal anti-inflammatory drugs (NSAIDs) in sewage sludge was developed and validated. The target compounds were extracted using pressurized hot water extraction (PHWE) and then purified and preconcentrated by three-phase hollow fiber liquid phase microextraction (HF-LPME) followed by LC–ESI-MS analysis. The PHWE was optimized with regard to the pH of solvent as well as other operational parameters. The optimum conditions were 0.01 M NaOH as the extraction solvent, temperature of 120 °C, pressure of 100 bar, static time 5 min, 5 cycles, flush volume 90% and purge time 60 s. Spike recoveries for sludge samples spiked at 200 ng g⁻¹ were in the range of 101–109% but for the native drugs in non-spiked sludge samples, recoveries were 38.9%, 59.8%, 90.3% and 47.8% for ketoprofen, naproxen, diclofenac and ibuprofen, respectively. Donor phase pH, ionic strength and extraction time were optimized for HF-LPME after PHWE. The optimum conditions were 2 h extraction at pH 1.5 without salt addition. Enrichment factors in the range of 947–1213 times were achieved (extraction recoveries were 23.6–30.3%) for HF-LPME after PHWE. The matrix effect on the ionization of drugs in LC–ESI-MS was also investigated. The results show that there is a smaller matrix effect (−8.9% to +14.6%) in comparison with other published values obtained using solid phase extraction (SPE) for clean-up after pressurized liquid extraction (PLE). Method detection limits (MDLs) and method quantification limits (MQLs) for different drugs were in the range of 0.4–3.7 ng g⁻¹ and 1.5–12.2 ng g⁻¹ in dried sludge samples, respectively. The characteristics of the proposed method were compared with those of other published works. The considerably lower ion suppression/enhancement and minimum use of organic solvents (a few microliters of di-n-hexyl ether) in the sample preparation step are two highlighted advantages of the proposed method in comparison with previously published works. The method was applied to determine NSAIDs in sewage sludge from Källby wastewater treatment plant (Lund, Sweden) in April, June, August and October 2010. The highest concentration level was recorded for ibuprofen in the April sewage sludge sample (588 ng g⁻¹) and all of the selected NSAIDs were detected in all the samples analyzed.     

Effective indirect enrichment and determination of nitrite ion in water and biological samples using ionic liquid-dispersive liquid-liquid microextraction combined with high-performance liquid chromatography

An ionic liquid dispersive liquid–liquid microextraction high-performance liquid chromatography (IL-DLLME-HPLC) method for effective enrichment and determination of nitrite ion in water and biological samples was developed. The method was based on the reaction of nitrite ion with p-nitroaniline in the presence of diphenylamine in acid media and IL-DLLME of azo product. The optimization of reaction and extraction conditions, such as kind and concentration of acid, reaction time, volume of reaction solvent, temperature, kind of extraction and dispersive solvent, volume of extraction and dispersive solvent, addition of salt, extraction and centrifugal time were studied. Under the optimal conditions, 1-octyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide IL-DLLME procedure provided high enrichment factor of 430 and good extraction recovery of 91.7% for nitrite ion. The linearity was observed in the range of 0.4–500.0 μg L⁻¹ with good correlation coefficient (r² = 0.9996). The relative standard deviations (RSDs) for five replicate measurements varied between 1.5% and 4.8%. The limit of detection of the method (S/N = 3) was 0.05 μg L⁻¹. The interference effect of some anions and cations was also tested. The developed method allowed achieving an excellent enrichment factor, yielding a lower LOD in comparison with other methods. Moreover, the proposed method was able to analyze nitrite ion in water and biological samples with satisfactory recovery ranged from 96.5% to 107.3%.     

遗传算法结合神经网络用于傅里叶变换红外光谱法测定航空润滑油中水分

采用傅里叶变换红外光谱法测定了航空润滑油中的水分,通过遗传算法(GA)优化选取有效波数点,用误差反向传播神经网络(BP-ANN)进行水分预测计算。模型的预测相关系数为0.957,预测标准偏差为0.022。随机抽取某型航空润滑油样品进行预测并对预测结果进行配对t检验,结果表明:红外光谱定量分析结果与标准方法测定值没有显著性差异,模型可以用于该型在用航空润滑油水分含量现场快速检测。     

Synthesis of Environmentally Safe Antiwear Additives to Lubricating Materials: State of the Art and Prospects

Russian Journal of Applied Chemistry - The review deals with the development and production of synthetic additives to lubricating oils and plastic lubricants, influencing the friction and wear of...     

Determination of copper traces in water samples by flow injection-flame atomic absorption spectrometry using a novel solidified floating organic drop microextraction method

A simple, rapid and inexpensive solidified floating organic drop microextraction (SFODME) and flow injection flame atomic absorption spectrometric determination (FI-FAAS) method for copper were developed. 3-amino-7-dimethylamino-2-methylphenazine (Neutral red, NR) was used as the complexing agent. Several factors affecting the microextraction efficiency, such as, pH, NR and sodium dodecylbenzenesulfonate (SDBS) concentration, extraction time, stirring rate, and temperature were investigated and optimized. Under optimized experimental conditions an enrichment factor of 541 was obtained for 100 mL of sample solution. The calibration graph was linear in the range of 0.5–20.0 ng mL^{− 1} and the limit of detection (3 s) was 0.18 ng mL^{− 1}, the limit of quantification (10 s) was 0.58 ng mL^{− 1}. The relative standard deviation (RSD) for 10 replicate measurements of 10 ng mL^{− 1} copper was 2.7%. The developed method was successfully applied to the extraction and determination of copper in different certified reference materials (Estuarine water, Slew 3 and fortified water, TM 23.2) and real water samples and satisfactory results were obtained.     

Carbon nanofibers extracted from soot as a sorbent for the determination of aromatic amines from wastewater effluent samples

The isolation and characterization of carbon nanofibers from soot obtained by burning natural oil is reported. The fibers were extracted from the soot with tetrahydrofuran followed by sonication. The carbon nanofibers were mixed with poly(vinyl alcohol) and electrospun to get the nanofiber mat. The extraction ability of electrospun nanofibers for the separation and preconcentration of aromatic compounds such as 3-nitroaniline, 4-chloroaniline, 4-bromoaniline and 3,4-dichloroaniline were tested and efficiently evaluated using high performance liquid chromatography. Under optimized conditions, the method showed good linearity in a range of 0.5–50 μg L⁻¹ with correlation coefficient ranging from 0.989 to 0.998. High precision of the extraction with RSD values of 4.5–5.8% and low LOD value in a range of 0.009–0.081 μg L⁻¹ for all aniline compounds were achieved. The proposed microextraction method offers advantages such as easy operation, high recovery, fast extraction, minimal use of organic solvent and elimination of tedious solvent evaporation and reconstitution steps.     

Environmentally Friendly Recovery and Characterization of Oil from Used Engine Lubricants

The present paper demonstrates the review of some acid processes as well as development of some new solvent processes for reclamation of used lubricating oils. The conventional processes are found to be of low yield (? 50%), laborious, time consuming and environmentally hazardous, because of residual acidic sludge. Based on the findings, a new modified Aluminium sulphate‐sodium silicate‐acid‐base method employing a small quantity of acid and giving a high yield (? 60%) is proposed. Further, to avoid use of acid, new regeneration processes based on solvent extraction were investigated. They are termed CCl₄‐alcohol method, Dodecane‐alcohol method and Toluene‐alcohol method. These processes are not only cost effective in terms of complete solvent recovery, but are rapid, less time consuming, more environmentally friendly and gave a high yield (70–75%). The virgin lubricants (Castrol GTX and Rimula‐C) as well as oils recovered by different methods were also characterized physicochemically to determine kinematic viscosity, density, refractive index, carbon distribution, wear scar diameter, % Conradson carbon residue, % ash, % chloride, pour point, etc. Results obtained show that many of the physico‐chemical properties of the recovered oils are in good agreement with those of virgin oils. The n.d.M analysis was also performed which shows that virgin oils have 73 ± 3% paraffinic carbon, 26 ± 3% naphthenic carbon and about 1% aromatic carbon. The recovered oils also showed nearly the same chemical composition. The UV‐Visible spectra of the recovered oils are all similar to those of virgin lubricants. The results suggest that the oils recovered by solvent treatments, particularly Dodecan‐alcohol and Toluene‐alcohol methods, may serve for lubrication purposes and can be rendered as excellent as virgin lubricants with the addition of certain additives. The proposed methods may be considered as alternative cost effective green techniques for acid reclamation processes and being the motivation of the present investigation.     

Nanoscale chemical structure variations in nano-patterned and nano-porous low-k dielectrics: A comparative photothermal induced resonance and infrared spectroscopy investigation

The recent development of the photothermal induced resonance (PTIR) technique has enabled atomic force microscope based infrared (AFM-IR) spectroscopy and imaging to be achieved at the nanometer scale. However, a direct correspondance between PTIR/AFM-IR and more traditional Fourier transform IR (FTIR) spectroscopy has been prohibited for nanometer scale features due to Rayleigh diffraction constraints that limit the latter to few micron spatial resolution. In this regard, we have overcome this challenge by fabricating 1 cm² arrays of 90 nm wide fins in a nano-porous low dielectric constant (i.e. low-k) amorphous hybrid inorganic-organic silicate material using standard nano-electronic fabrication techniques. With these structures, we demonstrate both a general correspondance between AFM-IR, FTIR, and Germanium attenuated total reflection (GATR) IR spectroscopy, as well as differences in the sensitivities that these techniques exhibit to the nanoscale variations in chemical structure induced in the low-k dielectric by the nanopatterning method. To further illustrate the sensitivity of AFM-IR to changes in chemical structure with nanometer resolution, the nanopatterned low-k dielectric was exposed to additional oxidizing plasma ash cleans post patterning. Focusing on the Si-CH₃ deformation band at ∼1275 cm⁻¹, both the AFM-IR, FTIR and GATR measurements show a clear reduction in the concentration of terminal methyl groups in the low-k dielectric as the oxidation potential of the plasma ash clean increased. These results further establish the power of AFM-IR to perform nanoscale IR spectroscopy and demonstrates a stronger correspondance between AFM-IR and well-known micron scale IR techniques such as FTIR and GATR.     

Crystal structure of N-phenyl-N′-isopropylp-phenylenediamine

We have previously reported the results of studies of the hydrogen bond nature in N-phenyl-N′-isopropyl-p-phenylenediamine by a quantum chemistry method and FTIR spectroscopy [1–3]. It is shown that the IR spectrum of N-phenyl-N′-isopropyl-p-phenylenediamine has IR bands in the vNH absorption region at 3380 cm⁻¹ and 3400 cm⁻¹ corresponding to the NH groups involved in hydrogen bonding.     

Solvent (ionic liquid) impregnated resin-based extraction coupled with dynamic ultrasonic desorption for separation and concentration of four herbicides in environmental water

A new method was developed for the determination of monolinuron, propazine, linuron, and prebane in environmental water samples. The solvent (ionic liquid) impregnated resin (IL-SIR)-based extraction coupled with dynamic ultrasonic desorption (DUSD) was applied to the separation and concentration of the analytes. The high performance liquid chromatography (HPLC) was applied to the determination of the analytes. The ionic liquid [C₆MIM][PF₆] was immobilized on Diaion HP20 resin by immersing the resin in ethanol solution containing [C₆MIM][PF₆]. The effect of extraction parameters, including pH value of sample solution, salt concentration in sample and extraction time, and elution conditions, including the concentration of ethanol in elution solvent, the flow rate of elution solvent and the ultrasonic power, were examined and optimized. The limits of detection and quantification for the analytes were in the range of 0.15-0.29 μg L⁻¹ and 0.51-0.98 μg L⁻¹, respectively. Some environmental water samples were analyzed and the analytical results were satisfactory.     

Combination of ultrasonic extraction and stripping analysis: an effective and reliable way for the determination of Cu and Pb in lubricating oils

The determination of metals in lubricating oil has been used as an important way to prevent components failures, to provide environmental information and in some cases, to identify adulteration. In this work, an effective and simple procedure is proposed for Cu and Pb determination in lubricating oils. An ultrasonic bath was employed for extraction of these elements from oil samples in a mixture 1:1 (v/v) of concentrated HCl and H₂O₂. A very efficient extraction of Cu and Pb (∼100%) was attained after 30 min of ultrasound, allowing the simultaneous determination of both metals using square-wave anodic stripping voltammetry at thin-film gold electrodes. The extraction procedure was performed in 4 mL polypropylene closed vessels and dozens of samples could be treated simultaneously in the same ultrasonic bath. The regions of the ultrasonic bath, where the maximum efficiency of extraction was attained were evaluated. Over the optimized region, 30 samples can be treated simultaneously. Used lubricating oils from automotive engines were analyzed by using the optimized extraction procedure.