用于固相微萃取的乙烯基开链冠醚复合涂层的研制

固相微萃取 (SPME)是一种新型的样品预处理技术 [1] ,其核心是 SPME装置中萃取头上的固相涂层 .目前商用 SPME涂层的种类较少 ,热稳定性较差 (推荐使用温度 2 0 0～ 2 80℃ ) ,使用寿命较短(40～ 1 0 0次 ) ,价格偏高 ,限制了其推广应用 .因此发展高选择性、高稳定性和高效的固     

Multivariate optimization of a solid phase microextraction-headspace procedure for the determination of benzene, toluene, ethylbenzene and xylenes in effluent samples from a waste treatment plant

A method based on solid-phase microextraction (SPME) and gas chromatography with flame ionization detection (GC-FID) has been optimized for the determination of benzene, toluene, ethylbenzene and xylenes (BTEX) in water released from a waste treatment plant. The extraction step was optimized using fractional factorial and central composite designs including the following experimental factors: saline concentration; extraction time; desorption time; agitation velocity; headspace volume. A multiple function was used to describe the experimental conditions for simultaneous extraction of the compounds. The procedure, based on direct SPME at 50 degrees C, using a polydimethylsiloxane fiber, showed good linearity (r>0.997 over a concentration range 2-200 microg L(-1)) and repeatability (relative standard deviation (RSD)<4.23%) for all compounds, with limits of detection ranging from 0.05 to 0.28 microg L(-1), and limits of quantification ranging from 0.14 to 0.84 microg L(-1). Concentrations of the target compounds in these samples were between 145.8 and 1891 microg L(-1).     

石墨烯层层键合固相微萃取纤维的制备及对多环芳烃的检测

通过3-巯基丙基三甲氧基硅烷处理银层包裹的不锈钢纤维,得到Si-OH功能化的纤维,氧化石墨烯被层层键合到Si-OH功能化的纤维上,还原氧化石墨烯得到石墨烯层层键合的固相微萃取纤维。该方法制备的新型石墨烯层层键合的固相微萃取纤维具有制备简单,机械性能强,萃取涂层牢固,萃取能力强等优势。建立具有较宽线性范围(5~200μg/L)、较低检测限(0.007~0.09μg/L)的固相微萃取-气相色谱分析方法,用该方法测定河水和雨水中多环芳烃的含量。所制备的新型纤维重现性好、稳定性高、萃取能力强,可实现对多环芳烃的痕量检测。     

Solid-phase microextraction and gas chromatography-electron capture detection analysis of trace organochlorine pesticides in water using novel benzo-15-crown-5 sol-gel coating

A novel dihydroxy-terminated benzo-15-crown-5 is synthesized and applied to prepare the solid-phase microextraction (SPME) fiber coating with sol-gel technology. Headspace SPME, as a simple, solvent-free method, is applied to the analysis of 16 organochlorine pesticides (OCPs) present at trace levels in a water sample. A homemade crown ether fiber coated with 80- micro m thickness was used for extraction. Analyses are performed using gas chromatography-electroncapture detection. The optimization of the extraction process is studied. Compared with commercially available SPME fibers, polydimethylsiloxane, the new phases show better selectivity and sensitivity toward OCPs. The linear concentrations range from 1 to 1000 ng/L, the detection limits are in the range of 0.01-0.5 ng/L, the recoveries are over 85%, and relative standard deviations are below 7.2% for these OCPs.     

Electrophoretic deposition strategy for the fabrication of highly stable functionalized silica nanoparticle coatings onto nickel‐titanium alloy wires for selective solid‐phase microextraction

A new strategy for the immobilization of phenyl‐functionalized silica nanoparticles onto nickel‐titanium alloy wires is presented. The homogeneous and compact silica nanoparticle coating was achieved on the hydrothermally treated nickel‐titanium wires with large surface area by electrophoretic deposition, and followed by self‐assembled modification of phenyltrichlorosilane. Coupled to high‐performance liquid chromatography with ultraviolet detection, the extraction performance of the fabricated fiber was evaluated using typical aromatic compounds in direct‐immersion mode of solid‐phase microextraction. Due to its high extraction efficiency and good selectivity for ultraviolet filters, the novel fiber was employed to investigate the key factors affecting the extraction of ultraviolet filters. Under the optimized conditions, the proposed method presented linear ranges from 0.05 to 300 μg/L with correlation coefficients higher than 0.999 and limits of detection from 0.005 to 0.058 μg/L. Relative standard deviations were below 4.3 and 5.6% for intraday and interday analyses at the spiking level of 50 μg/L ultraviolet filters with the single fiber, respectively. The proposed method was successfully applied to the selective concentration and sensitive detection of target ultraviolet filters from environmental water samples. Furthermore, the developed fiber can be used at least 200 times, and fabricated in a precisely controllable manner.     

Automated solid phase dynamic extraction--extraction of organics using a wall coated syringe needle

Extractions of liquid samples were carried out using wall coated needles prepared from stainless steel capillary columns instead of syringe needles. This micro extraction technique was applied to the analysis of pesticides in water. Important parameters influencing the extraction such as sample velocity, extraction time and also the desorption parameters were investigated and optimized. Automation of this technique was realized using a conventional automatic sampler. Limits of detection were improved using the multiple extraction/desorption technique. Chromatographic data and limits of detection were compared with those obtained by solid phase micro extraction (SPME). Using a needle with a 7 microns film yielded limits of detection varying from 0.001-0.1 microgram/L and were in the same range as those resulting from the extraction using a 100 microns polydimethylsiloxane (PDMS) SPME fiber. The main advantages of the needle extraction technique were the significantly higher extraction speed and the practical aspects of a stable steel needle compared to those of a fragile fiber. The extraction speed using a needle with a 7 microns film was up to five times higher than the speed of SPME using a 100 microns PDMS fiber. The steel needle could be stressed mechanically in a higher extent than a SPME fiber. Sample volumes and aliquots of liquid media could be handled and moved from one bottle to another using the automatic sampler.     

Dodecylsulfate-doped polypyrrole film prepared by electrochemical fiber coating technique for headspace solid-phase microextraction of polycyclic aromatic hydrocarbons

The electrochemical fiber coating (EFC) technique was used for the preparation of dodecylsulfate-doped polypyrrole (PPy-DS), and applied as a new fiber for solid-phase microextraction (SPME) procedures. PPy-DS film was directly electrodeposited on the surface of a platinum wire from an aqueous solution containing pyrrole and sodium dodecylsulfate, using cyclic voltammetry (CV). The effect of polymerization conditions and type of dopants on the thermal stability, adhesion and extraction characteristics of the fiber were investigated. The electron microscopy imaging of PPy-DS film suggested that the surface fiber coating was well-distributed with a porous structure. The fiber coating can be prepared easily in a reproducible manner, and it is inexpensive and has a stable performance at high temperatures (up to the 300 degrees C). The extraction properties of the fiber to eight polycyclic aromatic hydrocarbons (PAHs) were examined, using a headspace-SPME (HS-SPME) device coupled with gas chromatography-flame ionization detection (GC-FID) and gas chromatography-mass spectrometry (GC-MS). The results revealed study shows that PPy-DS as a SPME fiber coating is suitable for the successful extraction of PAHs. The effects of the extraction parameters including exposure time, sampling temperature, salt concentration, and stirring rate on the extraction efficiency have been studied. A satisfactory reproducibility for extractions from spiked water samples at PPb-level with R.S.D. < 7.6% (n = 7) was obtained. The calibration graphs were linear in the range of 0.5-100ng ml(-1) and detection limits for the selected PAHs were between 0.05-0.16 ng ml(-1). Comparing the HS-SPME results for extraction and determination of PAHs using PPy-DS fiber with the corresponding literature data using PDMS fiber shows that the proposed fiber has a better detection limit for low molecular weight PAHs. The life span and stability of PPy-DS fiber is good and it can be used more than 50 times at 250 degrees C without any significant change in sorption properties.     

微孔有机聚合物固相微萃取纤维的制备及在有机氯农药检测中的应用

利用1,3,6,8-四(4-醛基)芘和三聚氰胺为单体合成微孔有机聚合物(MOP),并将其固定在不锈钢丝上,制备成固相微萃取纤维涂层。将其用于顶空固相微萃取(HS-SPME),结合气相色谱-电子捕获检测手段,建立了对大米中有机氯农药的在线检测方法。实验考察了4种实验参数对富集能力的影响,得到了最优的实验条件:萃取温度80℃、萃取时间25 min、NaCl质量浓度200 g/L、解吸时间6 min。在此实验条件下,对有机氯农药的富集倍数达到115~318倍。方法在0.05~50μg/kg范围内具有良好的线性关系,检出限为2.4~11.3 ng/kg。同一纤维及不同纤维富集后测定结果的相对标准偏差范围分别为1.3%~13.1%和2.3%~13.6%。该方法简单、快速,可以实现对实际样品中有机氯农药的痕量分析。     

Nano-structured lead dioxide as a novel stationary phase for solid-phase microextraction

The first study on the high efficiency of nano-structured lead dioxide as a new fiber for solid-phase microextraction (SPME) purposes has been reported. The size of the PbO2 particles was in the range of 34-136 nm. Lead dioxide-based fibers were prepared via electrochemical deposition on a platinum wire. The extraction properties of the fiber to benzene, toluene, ethylbenzene, and xylenes (BTEX) were examined using headspace solid-phase microextraction (HS-SPME) mode coupled to gas chromatography-flame ionization detection (GC-FID). The results obtained proved the suitability of proposed fibers for the sampling of organic compounds from water. The extraction procedure was optimized by selecting the appropriate extraction parameters, including preparation conditions of coating, salt concentration, time and temperature of adsorption and desorption and stirring rate. The calibration graphs were linear in a concentration range of 0.1-100 microg l(-1) (R2 > 0.994) with detection limits below 0.012 microg l(-1) level. Single fiber repeatability and fiber-to-fiber reproducibility were less than 10.0 and 12.5%, respectively. The PbO2 coating was proved to be very stable at relatively high temperatures (up to 300 degrees C) with a high extraction capacity and long lifespan (more than 50 times). Higher chemical resistance and lower cost are among the advantages of PbO2 fibers over commercially available SPME fibers. Good recoveries (81-108%) were obtained when environmental samples were analyzed.     

Extraction and enrichment of polycyclic aromatic hydrocarbons by ordered mesoporous carbon reinforced hollow fiber liquid‐phase microextraction

A novel microextraction method, ordered mesoporous carbon reinforced hollow fiber liquid‐phase microextraction coupled with high‐performance liquid chromatography and fluorescence detection, was developed for the determination of some organic pollutants in water samples. Four polycyclic aromatic hydrocarbons (fluorene, anthracene, fluoranthene, and pyrene) were selected to validate this new method. Main parameters that could influence the extraction efficiency such as extraction time, fiber length, stirring rate, the type of the extraction solvent, pH value, the concentration of ordered mesoporous carbon, and salt effect were optimized. Under the optimal extraction conditions, good linearity was observed in the range of 2–1000 ng/L, with the correlation coefficients of 0.9954–0.9986. The recoveries for the spiked samples were in the range of 88.96–100.17%. The limits of detection of the method were 0.4–4 ng/L. The relative standard deviations varied from 4.2–5.9%. The results demonstrated that the newly developed method was an efficient pretreatment and enrichment procedure for the determination of polycyclic aromatic hydrocarbons in environmental water samples.     

Analysis of ethanol and methanol in human body fluids by headspace solid phase microextraction coupled with capillary gas chromatography.

A new method for extraction and analysis of ethanol and methanol in human whole blood, urine and saliva samples based on headspace solid phase microextraction (SPME) using silver sulfide (Ag(2)S) and polyvinyl chloride (PVC) coated on silver wire is described. Unlike commercial fibers, which are coated on fused silica, the proposed fiber has a metallic base to which the coating adheres very strongly. Due to metallic base, this fiber is very durable and is thermally stable up to 250 degrees C. After optimization of coating composition and microextraction conditions, the fiber was used for sampling of methanol and ethanol from human body fluids prior to capillary gas chromatographic analysis. The high recovery (>94%), low detection limits (5.6 mg/L for ethanol and 12.8 mg/L for methanol) and excellent linearity (>0.9900) of calibration graphs made the proposed method suitable for this purpose.     

Evaluation of two membrane‐based microextraction techniques for the determination of endocrine disruptors in aqueous samples by HPLC with diode array detection

In this study, the viability of two membrane‐based microextraction techniques for the determination of endocrine disruptors by high‐performance liquid chromatography with diode array detection was evaluated: hollow fiber microporous membrane liquid–liquid extraction and hollow‐fiber‐supported dispersive liquid–liquid microextraction. The extraction efficiencies obtained for methylparaben, ethylparaben, bisphenol A, benzophenone, and 2‐ethylhexyl‐4‐methoxycinnamate from aqueous matrices obtained using both approaches were compared and showed that hollow fiber microporous membrane liquid–liquid extraction exhibited higher extraction efficiency for most of the compounds studied. Therefore, a detailed optimization of the extraction procedure was carried out with this technique. The optimization of the extraction conditions and liquid desorption were performed by univariate analysis. The optimal conditions for the method were supported liquid membrane with 1‐octanol for 10 s, sample pH 7, addition of 15% w/v of NaCl, extraction time of 30 min, and liquid desorption in 150 μL of acetonitrile/methanol (50:50 v/v) for 5 min. The linear correlation coefficients were higher than 0.9936. The limits of detection were 0.5–4.6 μg/L and the limits of quantification were 2–16 μg/L. The analyte relative recoveries were 67–116%, and the relative standard deviations were less than 15.5%.     

Determination of triazine herbicides in aqueous samples by dispersive liquid-liquid microextraction with gas chromatography-ion trap mass spectrometry

A simple and rapid new dispersive liquid-liquid microextraction technique (DLLME) coupled with gas chromatography-ion trap mass spectrometric detection (GC-MS) was developed for the extraction and analysis of triazine herbicides from water samples. In this method, a mixture of 12.0 microL chlorobenzene (extraction solvent) and 1.00 mL acetone (disperser solvent) is rapidly injected by syringe into the 5.00 mL water sample containing 4% (w/v) sodium chloride. In this process, triazines in the water sample are extracted into the fine droplets of chlorobenzene. After centrifuging for 5 min at 6000 rpm, the fine droplets of chlorobenzene are sedimented in the bottom of the conical test tube (8.0+/-0.3 microL). The settled phase (2.0 microL) is collected and injected into the GC-MS for separation and determination of triazines. Some important parameters, viz, type of extraction solvent, identity and volume of disperser solvent, extraction time, and salt effect, which affect on DLLME were studied. Under optimum conditions the enrichment factors and extraction recoveries were high and ranged between 151-722 and 24.2-115.6%, respectively. The linear range was wide (0.2-200 microg L(-1)) and the limits of detection were between 0.021 and 0.12 microg L(-1) for most of the analytes. The relative standard deviations (RSDs) for 5.00 microg L(-1) of triazines in water were in the range of 1.36-8.67%. The performance of the method was checked by analysis of river and tap water samples, and the relative recoveries of triazines from river and tap water at a spiking level of 5.0 microg L(-1) were 85.2-114.5% and 87.8-119.4%, respectively. This method was also compared with solid-phase microextraction (SPME) and hollow fiber protected liquid-phase microextraction (HFP-LPME) methods. DLLME is a very simple and rapid method, requiring less than 3 min. It also has high enrichment factors and recoveries for the extraction of triazines from water.     

C18 functionalized graphene oxide as a novel coating for solid-phase microextraction

A novel C18 functionalized graphene oxide (GO) coated solid-phase microextraction fiber was prepared by a novel protocol. Based on the strong van der Waals interaction present in GO and abundant oxygenous groups in GO sheets, a simple layer-by-layer self-assembly method was used in the preparation process and then C18 was successfully self-assembled on GO via C-O-Si bonding. Coupled with gas chromatography, extraction performance of the fiber was tested with polycyclic aromatic hydrocarbons (PAHs) as model analytes. The fiber not only exhibited excellent extraction efficiency and selectivity, but also showed many advantages including high rigidity, long service life and well stability toward organic solvent, acidic and alkali solutions, and high temperature. The relative standard deviations for single-fiber repeatability and fiber-to-fiber reproducibility were less than 7.26 and 17.25%, respectively. The detection limits to the PAHs were less than 0.08 μg L(-1) and the calibration curves were linear in a wide range for all analytes. The as-established Solid-phase microextraction GC method was also successfully used for determination of PAHs in two real water samples.     

Solid-phase microextraction for the gas chromatography mass spectrometric determination of oxazole fungicides in malt beverages

This paper describes a method for the sensitive, selective, and solvent-free determination of six oxazole fungicide residues (hymexazol, drazoxolon, vinclozolin, chlozolinate, oxadixyl, and famoxadone) in malt beverages. Direct immersion solid-phase microextraction (DI-SPME) coupled to gas chromatography with mass spectrometry in the selected ion monitoring mode, GC-MS(SIM), is used. A comparison of the optimal fiber used, a polar carbowax-divinylbenzene 70-microm fiber, and a nonpolar polydimethylsiloxane 100-microm fiber was carried out. Optimal extraction conditions were 60 degrees C and an extraction time of 30 min under continuous stirring. Desorption was carried out at 250 degrees C for 5 min. Detection limits ranged from 0.006 to 0.3 microg L(-1) at a signal to noise ratio of 3, depending on the compound. The proposed method was successfully applied to malt beverages including malt, beer, and whisky, and none of the samples contained residues higher than detection limits.     

Polypyrrole/graphene composite-coated fiber for the solid-phase microextraction of phenols

A polypyrrole (Ppy)/graphene (G) composite was developed and applied as a novel coating for use in solid-phase microextraction (SPME) coupled with gas chromatography (GC). The Ppy/G-coated fiber was prepared by electrochemically polymerizing pyrrole and G on a stainless-steel wire. The extraction efficiency of Ppy/G-coated fiber for five phenols was the highest compared with the fibers coated with either Ppy or Ppy/graphene oxide (GO) using the same method preparation. Significantly, compared with various commercial fibers, the extraction efficiency of Ppy/G-coated fiber is better than or comparable to 85 μm CAR/PDMS fiber (best extraction efficiency of phenol, o-cresol, and m-cresol in commercial fibers) and 85 μm polyacrylate (PA) fiber (best extraction efficiency of 2,4-dichlorophenol and p-bromophenol in commercial fibers). The effects of extraction and desorption parameters such as extraction time, stirring rate, and desorption temperature and time on the extraction/desorption efficiency were investigated and optimized. The calibration curves were linear from 10 to 1000 μg/L for o-cresol, m-cresol, p-bromophenol, and 2,4-dichlorophenol, and from 50 to 1000 μg/L for phenol. The detection limits were within the range 0.34-3.4 μg/L. The single fiber and fiber-to-fiber reproducibilities were <8.3 (n=7) and 13.3% (n=4), respectively. The recovery of the phenols spiked in natural water samples at 200 μg/L ranged from 74.1 to 103.9% and the relative standard deviations were <3.7%.     

聚醚砜酮涂层纤维顶空固相微萃取-气相色谱法分析水中痕量的酚类化合物

应用自制的聚醚砜酮(PPESK,30 μm)涂层纤维,采用顶空固相微萃取-气相色谱法测定水中痕量的酚类化合物。优化了固相微萃取温度、萃取时间、pH值和离子强度。方法的检出限为0.003～0.041 μg/L,相对标准偏差低于16%(n=5)。将PPESK涂层纤维与商品化的聚丙烯酸酯涂层纤维对比,结果表明PPESK萃取酚类化合物有较高的萃取富集倍数。用所制备的PPESK萃取头分析自来水、海水等实际水样,20 μg/L添加水平下的回收率分别为100.5%～111.8%和94.8%～117.3%。     

荧光衍生化-磁分散固相萃取/高效液相色谱检测池塘水与蔬菜中3种挥发性异味物质

以6-碳酰氯左氧氟沙星(LFC-Cl)为衍生试剂,磁性氧化石墨烯(MGO)为吸附剂,建立了2-甲基异莰醇(2-MIB)、土臭素(GSM)和3-甲基-1-丁醇(3-MB)的高效液相色谱荧光检测(HPLC-FLD)分析方法。在浓度为0.05 mol/L的4-二甲氨基吡啶(DMAP)乙腈溶液中,衍生温度60℃,反应时间90 min,超声波辅助条件下,可完成上述3种醇类挥发性异味物质(VOCs)的衍生化。在吸附剂用量20 mg、萃取时间20 min、解吸剂为乙腈(含1%甲酸)、解吸时间3 min条件下,能实现3种异味物质衍生物的富集和净化。在优化的HPLC条件下,15 min内可实现3种衍生物的基线分离和高灵敏检测。方法检出限(LOD)为0.020~0.95 ng/L,定量下限(LOQ)为0.10~3.3 ng/L,线性、精密度和回收率良好。与已报道的方法相比,该方法具有灵敏度高、样品前处理简单、仪器普适性好等优势,可用于池塘水、蔬菜中VOCs的快速、定量测定,为食品和环境水样监测提供了一种新方法。     

Polyethylene glycol/graphene oxide coated solid‐phase microextraction fiber for analysis of phenols and phthalate esters coupled with gas chromatography

A new polyethylene glycol/graphene oxide composite material bonded on the surface of a stainless‐steel wire was used for solid‐phase microextraction. The layer‐by‐layer structure increased the adsorption sites of the novel fiber, which could facilitate the extraction of trace compounds. The polyethylene glycol/graphene oxide was characterized by Fourier transform infrared spectroscopy and elemental analysis, which verified that polyethylene glycol was successfully grafted onto the surface of graphene oxide. The performance of the polyethylene glycol/graphene oxide coated fiber was investigated for phenols and phthalate esters coupled with gas chromatography with flame ionization detection under the optimal extraction and desorption conditions, and the proposed method exhibited an excellent extraction capacity and high thermal stability. Wide linear ranges were obtained for the analytes with good correlation coefficients in the range of 0.9966–0.9994, and the detection limits of model compounds ranged from 0.003 to 0.025 μg/L. Furthermore, the as‐prepared fiber was used to determine the model compounds in the water and soil samples and satisfactory results were obtained.     

Preparation of single-walled carbon nanotube fiber coating for solid-phase microextraction of organochlorine pesticides in lake water and wastewater

The feasibility of single-walled carbon nanotubes (SWCNTs) as adsorbents for solid-phase microextraction was investigated by using organochlorine pesticides (OCPs) as model compounds. SWCNTs were attached onto a stainless steel wire through organic binder. Potential factors affecting the extraction efficiency were optimized, including extraction time, extraction temperature, desorption time, desorption temperature, and salinity. The developed method has a linear range of 2-800 ng/L for most analytes, with coefficients of correlation ranging from 0.9911 to 0.9996, LODs ranged from 0.19 to 3.77 ng/L (S/N = 3), and RSDs in the range of 3.5-13.9% (n = 5). Compared with the commercial PDMS fiber, the SWCNT fiber has better thermal stability (over 350 degrees C) and longer life span (over 150 times). The developed method was applied to determine trace OCPs in lake water and wastewater samples with external standard calibration. Results showed that OCP contamination was very low in these samples, and HCHs were detected in almost all water samples while DDT concentrations were almost under detection limits in these samples. Recoveries obtained at 20 ng/L spiking level were in the range of 88.4-111% for OCPs in lake water. For wastewater samples, however, the recoveries were satisfactory for HCHs (63.6-97.1%) but relatively low for DDTs (44.7-116%) due to the high content of organic matter in wastewater.