太赫兹量子级联激光器光束特性分析

用有限元法计算太赫兹量子级联激光器激光模式的阈值增益.结果表明:接触层厚度和掺杂浓度对阈值增益的影响远远大于波导宽度和激射波长;接触层厚度较小(大)和掺杂浓度较低(高)时,TM₁(TM₀)模的阈值增益较小.在此基础上,用矢量衍射理论分析岀射光束的远场特性,得到光束的远场光斑基本是椭圆;x方向的远场散射角随波导宽度或激射波长的增加分别线性减小或增加,尽管对应的接触层厚度和掺杂浓度不同,但TM₀和TM₁模x方向的远场散射角相同;另外,还得到y方向远场散射角不受波导宽度或少受激射波长的影响.在阈值增益和光束质量方面,TM₁模都优于TM₀模.     

分数自成像平面波导的光束组束

研究了激光束在分数自成像平面波导中的传输特性,提出了利用分数自成像平面波导进行光束组束的技术方案,讨论了激光束之间相位失配对光束组束的影响,并对两个输出平均功率为300W的板条激光器的光束组束进行了数值实验模拟.结果表明,分数自成像平面波导的光束组束可以有效地改善多个激光器组束后的光束质量因子M²,从而提高激光输出的亮度;而且这种组束方法对激光束之间相位失配的敏感度明显降低. 关键词： 分数自成像 平面波导 组束 光束质量     

Output mode characteristics of an in-phase locked gain waveguide array CO2 laser

In this paper,experimental and theoretical studies of the output mode characteristics of an in-phase locked gain waveguide array CO 2 laser are reported.The experimental results of the optical oscillation mode frequency,the far-field intensity distribution and the burnt pattern of the sliced waveguide array laser are obtained.A revised mode expression of the rectangle waveguide,which is suited for this waveguide array CO 2 laser,is proposed.The theoretical simulation results based on the revised mode expression are shown to be in good agreement with the experimental results.     

Transverse mode coupling in narrow-ridge waveguide laser diodes

The letter presents numerical data and gives an explanation for the spontaneous creation of spatial patterns in narrow-ridge waveguide laser diodes by including the effect of diffraction and non-linear coupling between transverse modes and the active material. In addition, experimental measurements from several laser diodes are made and directly compared to the simulation. Excellent agreement between numerical and experimental data is found.     

Effects of metal irises on the guided-mode properties in asymmetrical slab waveguides

The diffraction phenomenon caused by metal transverse irises placed into an asymmetrical slab waveguide is examined by using the integral equation method. We concentrate on the possibility of controlling the radiation characteristics of the structure by changing the irises positions and the slab waveguide asymmetry. The aperture electric-field distribution is expressed in terms of a finite series of Chebyshev polynomials. The dominant TE guided-mode reflection and transmission coefficients, the near-field distribution and the far-field radiation pattern are calculated, while numerical results are presented for several cases of asymmetrical slab waveguides and different irises’ positions.     

Field distribution in waveguide of mid-infrared strain-compensated InAlAs/InGaAs/InP quantum cascade laser

In this paper we present calculated mode distributions in double-trench mesa waveguide of a quantum cascade laser (QCL) and far-field distributions of the QCL beam—both calculated and experimental. We have computed electric field distribution in the waveguide, confinement factor and mode absorption for different transversal modes and far-field distributions based on them. The parameters of the modes were calculated for various sizes: width and length, of the QCL waveguide. The maximal mesa width for single-transverse-mode operation was determined to be about 0.7 times wavelength. This value and the mode discrimination depend only slightly on the resonator length. To verify experimentally the results of the simulations we have measured power distribution in the far field by using goniometric profiler. The measured distribution agrees well with the results of the numerical calculations.     

啁啾脉冲参数对合成光束的远场光强的影响

光束合成是提高激光功率及光束质量的一种有效方法,啁啾脉冲高斯光束的各参数都会影响合成的效果。利用夫琅禾费衍射积分公式导出了两束啁啾脉冲高斯光束合成的远场光强的解析式,得知远场光强与啁啾参数、脉宽及谱宽等参数有关。对远场光强进行了数值模拟,结果表明:对甚多束光束合成而言,单元激光间的啁啾参数增大、脉宽差值减小或者谱宽差值增大,均有利于轴上光强的增大及远场光强分布集中于传输轴附近。     

Optical properties of He+-implanted and diamond blade-diced terbium gallium garnet crystal planar and ridge waveguides

Terbium gallium garnet (Tb₃Ga₅O₁₂, TGG) crystal can be used to fabricate various magneto-optical devices due to its optimal Faraday effect. In this work, 400-keV He⁺ ions with a fluence of 6.0×10¹⁶ ions/cm² are irradiated into the TGG crystal for the planar waveguide formation. The precise diamond blade dicing with a rotation speed of 2×10⁴ rpm and a cutting velocity of 0.1 mm/s is performed on the He⁺-implanted TGG planar waveguide for the ridge structure. The dark-mode spectrum of the He⁺-implanted TGG planar waveguide is measured by the prism-coupling method, thereby obtaining the relationship between the reflected light intensity and the effective refractive index. The refractive index profile of the planar waveguide is reconstructed by the reflectivity calculation method. The near-field light intensity distribution of the planar waveguide and the ridge waveguide are recorded by the end-face coupling method. The He⁺-implanted and diamond blade-diced TGG crystal planar and ridge waveguides are promising candidates for integrated magneto-optical devices.     

Scattering of electron stream waves on metal-dielectric periodic structures

The results of the theoretical and experimental research of the surface waves scattering of an electron stream and a planar dielectric waveguide on metal-dielectric structures of the dielectric prism — band diffraction grating-type are presented. Within the approximation of the given current there has been carried out a numerical analysis of energy characteristics of diffraction-Cerenkov radiation for a wide interval of the main system parameters change. The results of numerical analysis are confirmed by the data of experimental simulation.     

The effect of double heterojunction waveguide parameters on the far field emission patterns of lasers

A model of double-heterostructure lasers is developed which gives the far-field pattern of the laser in terms of such waveguide parameters as the active region width and the dielectric constants of the layers forming the waveguide. For symmetrical waveguides an explicit expression is given. Experimental results are presented which show a close agreement between the theory and the measured far-field patterns. By adding an extra passive layer to the conventional double heterostructure laser a structure is produced in which the measured half-power width of the far-field distribution is reduced from 55° to 32°. It is shown in this case that the model is useful for estimating the near-field pattern from the measured far-field pattern and hence determining the unknown waveguide parameters.     

拼接光栅的偏差对光束空间特性的影响

用拼接小尺寸多层介质膜衍射介质膜衍射光栅的办法制作大口径的高破坏阈值光栅成为解决拍瓦激光系统输出能量的关键技术———光栅拼接技术。拼接的每个光栅都存在五维自由度的偏差,对激光脉冲的空间特性和时间特性产生影响。用夫琅禾费衍射的方法分析了拼接光栅的偏差对光束空间特性的影响,建立了偏差和远场强度分布之间的函数关系并用数值方法进行模拟,得出角度偏差对光束远场分布的影响可以忽略,而位移偏差:光栅间拼缝和前后位移偏差是影响光束远场分布的关键因素。     

A general method for analyzing the multilayer planar waveguide

A general method for analyzing the multilayer planar optical waveguide is presented. This method can also be used to predict the evolution of a wave propagating in the multibranch planar waveguide. The numerical simulation results show that the prediction is correct.     

一维三通道波导列阵CO_2激光器输出特性研究

由理论和实验研究了一维三通道空心桥脊波导列阵CO_2激光器的远场输出特性,观察到三种不同模态输出的远场光强分布形状.由于实验测量值与通常假定条件下理论值的偏异.本文对原假定条件进行修正.由此导出的理论表达式较好地描述了实验结果.     

Continuous-wave and passively Q-switched cladding-pumped planar waveguide lasers

Greater than 12 W of average output power has been generated from a diode-pumped Yb:YAG cladding-pumped planar waveguide laser. The laser radiation developed is linearly polarized and diffraction limited in the guiding dimension. A slope efficiency of 0.5 W/W with a peak optical-optical conversion efficiency of 0.31 W/W is achieved. In a related structure, greater than 8 W of Q -switched average output power has been generated from a Nd:YAG cladding-pumped planar waveguide laser by incorporation of a Cr(4+): YAG passive Q switch monolithically into the waveguide structure. Pulse widths of 3 ns and pulse-repetition frequencies as high as 80 kHz have been demonstrated. A slope efficiency of 0.28 W/W with a peak optical-optical conversion efficiency of 0.21 W/W is achieved.     

用转移矩阵法研究LNN型非线性平面光波导

用转移矩阵法数值分析了芯区和衬底为非线性介质、覆盖层为线性介质结构平面光波导的传播特性,包括TM的模场分布和功率与有效折射率之间关系的分析.解析地表达了模式本征方程和功率分布,对非线性介质中电场强度与介质非线性系数的关系进行了研究.计算结果表明,TM的模场分布和功率与有效折射率及介质的非线性系数有关.     

Planar waveguide lasers and structures created by laser ablation — an overview

The parameters of planar and channel waveguide lasers fabricated by different techniques are reviewed. Materials and properties of thin films used for creation of planar waveguide lasers are summarized. The parameters of active and passive planar waveguides created by the method of pulsed laser deposition and problems of laser deposition are described. The aspects of laser generation of planar waveguide lasers, resonators and channel waveguides are presented. The results of our experiments of laser deposition of thin Ti:sapphire layers and thin layers of Nd:YAG and Nd:YAP are briefly discussed. This work was supported by the grant of Czech Grant Agency No. 102/96/0429.     

二极管激光线阵光束的远场特性

 利用X-Y函数记录仪测试了双异质结连续60 W,1×19激光二极管线阵（LDB）发射光束的空间光强分布和时间稳定性,被测样品的型号为JOLD-60-CPNN-1L。实验结果表明:组成DLB的19个二极管发射的光束基本上是独立传输的,DLB光束远场光强分布由19个子束非相干叠加而成,并且不随时间变化,发光区间距不相等。以实验为依据,对理论模型做了改进。将低注入电流的实验与用改进的理论模型的计算结果做了比较,二者符合甚好。     

Study of RF Excited CO 2 Waveguide Laser Array

Ｉｎｔｒｏｄｕｃｔｉｏｎ　　ＴｈｅＲＦｅｘｃｉｔｅｄｔｅｃｈｎｉｑｕｅｔｏＣＯ２ｗａｖｅｇｕｉｄｅｌａｓｅｒｈａｓｂｅｅｎｒａｐｉｄｌｙｉｍｐｒｏｖｅｄ．ＭａｎｙｎｅｗｓｔｒｕｃｔｕｒｅｓｈａｓａｐｐｅａｒｅｄｓｉｎｃｅＫ．Ｄ．Ｌａａｋｍａｎ［１］ｍａｄｅｆｉｒｓｔｌｙｏｕｔｔｒａｎｓｖｅｒｓｅｅｘｃｉｔｅｄｗａｖｅｇｕｉｄｅＣＯ２ｌａｓｅｒｆｉｒｓｔｉｎ１９７７,ｓｕｃｈａｓｃｏｈｅｒｅｎｔｐｈａｓｅｌｏｃｋｅｄ１×２ａｒｒａｙＣＯ２ｗａｖｅｇｕｉｄｅｌａｓｅｒｇｉｖｅｎｂｙＤ．Ｇ．Ｙｏｕｍ…     

Integrated diffractive optical mode converter for fiber-to-waveguide coupling

An integrated diffractive optical mode converter, which can be integrated into planar lightwave circuits (PLCs), consisting of a diffractive optical element (DOE) and a slab waveguide is presented for fiber-to-waveguide coupling. The DOE is designed using iterative phase retrieval algorithm. In the iterative algorithm, we introduce a new modification of far-field amplitude constraint to provide very high mode conversion quality. Compared with previously published mode converters, the scheme is more universal because it is applicable for any waveguide structure. In simulation, coupling losses lower than 0.12 dB have been reached for all the discussed waveguides. The converter is shown to be polarization-insensitive and applicable in multi-wavelength PLCs. And the tolerance on axis misalignment has been investigated.     

A Passband-Flattened EDG Demultiplexer with an Air-Trenched Taper

A novel passband flattening method for a planar waveguide demultiplexer based on an etched diffraction grating is presented. A strongly confined taper is formed by etching air trenches at both sides of the input waveguide. The geometric parameters of the taper are optimized by considering the figure of merit, ripple, and loss. Numerical simulation for a design example is given to illustrate the passband flattening method.