含非完整界面涂层夹杂中螺型位错的弹性分析

研究了含非完整界面圆形涂层夹杂内部一个螺型位错在夹杂、涂层与无限大基体材料中产生的弹性场.运用复变函数函数方法,获得了三个区域复势函数的解析解答.利用求得的应力场和Peach-Koehler公式,得到了作用在螺型位错上位错力的精确表达式.主要讨论了两个非完整界面对位错力的影响规律.结果表明,涂层界面对夹杂内部螺型位错的吸引力随着界面粘结强度的弱化而变大.界面非完整程度增加削弱材料弹性失配对位错力的影响.在一定条件下,非完整界面可以改变夹杂内位错与涂层/基体系统之间的引斥干涉规律,并使位错在夹杂内部产生一个稳定或非稳定的平衡点.     

压电螺位错与含界面裂纹圆形涂层夹杂的干涉

研究位于基体或夹杂中任意点的压电螺型位错与含界面裂纹圆形涂层夹杂的电弹耦合干 涉问题. 运用复变函数方法，获得了基体，涂层和夹杂中复势函数的一般解答. 典型例 子给出了界面含有一条裂纹时，复势函数的精确级数形式解. 基于已获得的复势函数和广 义Peach-Koehler公式，计算了作用在位错上的像力. 讨论了裂纹几何条件，涂层厚度和材 料特性对位错平衡位置的影响规律. 结果表明，界面裂纹对涂层夹杂附近的位错运动有很大 的影响效应，含界面裂纹涂层夹杂对位错的捕获能力强于完整粘结情况；并发现界面裂纹长 度和涂层材料常数达到某一个临界值时可以改变像力的方向. 解答的特殊情形包含了以 往文献的几个结果.     

增强相/夹杂内螺位错偶极子与含共焦钝裂纹椭圆夹杂的干涉效应

运用弹性力学的复势方法,研究了纵向剪切下增强相/夹杂内螺型位错偶极子与含共焦钝裂纹椭圆夹杂的干涉效应,得到了该问题复势函数的封闭形式解答,由此推导出了夹杂区域的应力场、作用在螺型位错偶极子中心的像力和像力偶矩以及裂纹尖端应力强度因子级数形式解。并分析了位错偶极子倾角 、钝裂纹尺寸和材料常数对位错像力、像力偶矩以及应力强度因子的影响。数值计算结果表明：位错像力、像力偶矩以及应力强度因子均随位错偶极子倾角做周期变化;夹杂内部的椭圆钝裂纹明显增强了硬基体对位错的排斥,减弱了软基体对位错的吸引,且对于硬夹杂,位错出现了一个不稳定平衡位置,该平衡位置随钝裂纹曲率的增大不断向界面靠近;变化 值将出现改变位错偶极子对应力强度因子作用方向的临界值。     

纳米线涂层中失配位错偶极子分析

研究了纳米线环形晶体薄膜涂层中失配位错偶极子与纳米线的干涉效应,并考虑纳米尺度应力效应及纳米线晶格失配的影响。运用弹性复势方法,分别获得了涂层和纳米线区域复势函数的精确解析解。利用求得的应力场和Peach-Koehler公式,得到了作用在螺型位错偶极子上像力和失配应力的精确表达式。算例结果表明,涂层纳米线界面应力和失配应力对涂层中失配位错偶极子的作用影响很大,由于界面应力和失配应力的存在,可以改变涂层内位错偶极子与纳米线干涉的引斥规律。与宏观尺度下的线型材料相比,纳米线材料由于界面效应的影响,位错偶极子在涂层中平衡位置的数量增加,涂层中更容易产生失配位错偶极子。考虑纳米线晶格失配的影响后,位错偶极子在涂层中平衡位置的数量增加。由此可知,减小纳米线晶格失配的影响,可以控制失配位错偶极子的产生。     

穿透夹杂界面的半无限楔形裂纹尖端螺型位错的发射研究

摘要：研究了穿透圆形夹杂界面的半无限楔形裂纹与裂纹尖端螺型位错的干涉问题。应用复变函数解析延拓技术与奇性主部分析方法,得到了位错位于半圆形夹杂内部时,半无限基体和半圆形夹杂内复势函数的解析解。然后利用保角映射技术得到了穿透圆形夹杂界面的半无限楔形裂纹尖端螺型位错产生的应力场以及作用在位错上的位错力的解析表达式。主要讨论了螺型位错对裂纹的屏蔽效应以及从楔形裂纹尖端发射位错的临界载荷条件。研究结果表明正的螺型位错可以削弱楔形裂纹尖端的应力强度因子,屏蔽裂纹的扩展,屏蔽效应随位错方位角的增大而减小。位错发射所需的无穷远临界应力随发射角的增加而增大,最可能的位错发射角度为零度,直线裂纹尖端位错的发射比楔形裂纹尖端位错的发射更容易,硬基体抑制位错的发射。     

纵向剪切下含共焦刚性核弹性椭圆夹杂中的螺型位错干涉

摘 要 研究了无穷远纵向剪切下无限大基体中含共焦刚性核弹性椭圆夹杂内任意位置螺型位错的干涉问题。运用复变函数保角映射、解析延拓等方法,获得了基体与夹杂区域的应力场的级数形式精确解,并得出了位错像力的解析表达式,导出了纵向剪切下两椭圆界面最大应力及其比值公式。分析结果表明：夹杂内部的刚性核对位错与夹杂的干涉产生明显的扰动效应,排斥硬夹杂内位错,并使之不断趋近弹性夹杂界面。对于软夹杂,夹杂中的位错存在稳定的平衡位置,当位错位于刚性核和平衡位置之间时,位错会趋于弹性夹杂界面;当位错位于平衡位置和弹性夹杂界面之间时,位错会离开界面。结果还显示,夹杂的长轴和短轴之比对位错与夹杂的干涉也有着不可忽视的影响,尤其当位错在刚性核附近时,随着夹杂的长、短轴比值的减小,核对位错的排斥力也明显减弱。本文解答包含了多个以往文献成果。     

含界面层圆形夹杂中螺旋位错的弹性分析

研究了复合材料含界面层圆形夹杂内部的一个螺旋位错在夹杂，界面层与基体材料中产生的弹性干涉，将复变函数的分区亚纯函数理论与柯西型积分，罗朗级数相结合，求出了各分区复势的解析关系，化为一个关于界面层复势的函数方程，用显示式表达了问题的结果，揭示了界面层参数对位错干涉能与位错力的影响规律。该解析方法较经典级数方法未知量大量减少，表达式更加简洁，结果的特殊情形包含了若干已有成果。     

位错偶极子和Ⅲ型界面裂纹的干涉效应

研究了多晶体材料中螺型位错偶极子和界面裂纹的弹性干涉作用.利用复变函数方法,得到了该问题复势函数的封闭形式解答.求出了由位错偶极子诱导的应力场和裂纹尖端应力强度应子,分析了偶极子的方向,偶臂和位置以及材料失配对应力强度因子的影响.推导了作用在螺型位错偶极子中心的像力和力偶矩,并讨论了界面裂纹几何条件和不同材料特征组合对位错偶极子平衡位置的影响规律.结果表明,裂纹尖端的螺型位错偶极子对应力强度因子会产生强烈的屏蔽或反屏蔽效应.同时,界面裂纹对螺型位错偶极子在材料中运动有很强的扰动作用.     

压电螺型位错和共线界面刚性线夹杂的干涉效应

研究了压电材料中压电螺型位错和共线界面导电刚性线夹杂的电弹干涉效应．运用复变函数解析延拓技术与奇性主部分析方法,获得了该问题的一般解答．作为算例,求出了界面含一条刚性线夹杂时两种压电介质区域广义应力函数的封闭形式解．导出了作用在位错上的像力和刚性线夹杂表面剪应力和电位移的解析表达式．讨论了界面刚性线长度,两种材料的剪切模量比和压电系数比对位错力和刚性线表面剪应力的影响规律．为进一步研究该类问题提供了一个基本解。     

螺型位错偶极子与圆形界面刚性线的干涉效应研究

本文重点研究螺型住错偶极子和圆形夹杂界面刚性线的弹性干涉效应。利用复变函数方法,得到了该问题的一般解;此外还求出了只含一条界面刚性线时的封闭解答,得到了刚性线尖端的应力强度因子以及作用在螺型位错偶板子中心的像力和像力偶矩。研究结果表明：位错偶板子对应力强度因子具有很强的屏蔽或反屏蔽效应;软夹杂吸引位错偶极子,而刚性线排斥位错偶板子,在一定条件下,位错偶极子在刚性线附近出现一个平衡位置;当刚性线的长度争材料剪切模量比达到临界值时,可以改变偶极子和界面之间的干涉机理;刚性线长度对位错偶极子中心像力偶矩也有很大的影响。     

New phenomena concerning a screw dislocation interacting with two imperfect interfaces

Dislocation mobility and stability in nanocrystals and electronic materials are influenced by the material composition and interface conditions. Its mobility and stability then affect the mechanical behaviors of the composites. In this paper, we first address, in detail, the problem of a screw dislocation located in an annular coating layer which is imperfectly bonded to the inner circular inhomogeneity and to the outer unbounded matrix. Both the inhomogeneity-coating interface and coating-matrix interface are modeled by a linear spring with vanishing thickness to account for the possible damage occurring on the interface. An analytic solution in series form is derived by means of complex variable method, with all the unknown constants being determined explicitly. The solution is then applied to the study of the dislocation mobility and stability due to its interaction with the two imperfect interfaces. The most interesting finding is that when the middle coating layer is more compliant than both the inner inhomogeneity and the outer unbounded matrix and when the interface rigidity parameters for the two imperfect interfaces are greater than certain values, one stable and two unstable equilibrium positions can exist for the dislocation. Furthermore, under certain conditions an equilibrium position, which can be either stable or unstable (i.e., a saddle point), can exist, which has never been observed in previous studies. Results for a screw dislocation interacting with two parallel straight imperfect interfaces are also presented as the limiting case where the radius of the inner inhomogeneity approaches infinity while the thickness of the coating layer is fixed.     

Electroelastic interaction between piezoelectric screw dislocation and circularly layered inclusion with imperfect interfaces

The interaction between a piezoelectric screw dislocation and an interphase layer in piezoelectric solids is theoretically investigated.Here,the dislocation located at arbitrary points inside either the matrix or the inclusion and the interfaces of the interphase layer are imperfect.By the complex variable method,the explicit solutions to the complex potentials are given,and the electroelastic fields can be derived from them.The image force acting on the dislocation can be obtained by the generalized PeachKoehler formula.The motion of the piezoelectric screw dislocation and its equilibrium positions are discussed for variable parameters.The important results show that,if the inner interface of the interphase layer is imperfect and the magnitude of degree of the interface imperfection reaches the certain value,two equilibrium positions of the piezoelectric screw dislocation in the matrix near the interface are found for the certain material combination which has never been observed in the previous studies(without considering the interface imperfection).     

Dislocation stability in three-phase nanocomposites with imperfect interface

Interface imperfection can significantly affect the mechanical properties and failure mechanisms as well as the strength and toughness of nanocomposites. The elastic behavior of a screw dislocation in nanoscale coating with imperfect interface is studied in the three-phase composite cylinder model. The interface between inner nanoin- homogeneity and intermediate coating is assumed as perfectly bonded. The bonding between intermediate coating and outer matrix is considered to be imperfect with the assumption that interface imperfection is uniform, and a linear spring model is adopted to describe the weakness of imperfect interface. The explicit expression for image force acting on dislocation is obtained by means of a complex variable method. The analytic results indicate that inner interface effect and outer interface imperfection, simultaneously taken into account, would influence greatly image force, equilibrium position and stability of dislocation, and various critical parameters that would change dislocation stability. The weaker interface is a very strong trap for glide dislocation and, thus, a more effective barrier for slip transmission.     

Misfit dislocation dipoles in coated fibrous composites

We investigate the stability of a misfit screw dislocation dipole in a coated fibrous composite. The fiber is stiffer whereas the coating is more compliant than the matrix. A critical coating thickness is identified for given material parameters of the composite. For a compliant coating below the critical thickness, there exist an inner unstable and an outer stable equilibrium position in the matrix for the dislocation dipole. However, for a compliant coating above the critical thickness, the dislocation dipole will be attracted to the coating–matrix interface. If the coating thickness is greater than the inclusion radius, the dislocation dipole cannot lodge in the matrix no matter what values of the material parameters are chosen.     

A SCREW DISLOCATION IN A THREE-PHASE COMPOSITE CYLINDER MODEL WITH INTERFACIAL RIGID LINES

The problem of the elastic interaction between a screw dislocation and a three-phase circular inclusion with interracial rigid lines （anti-cracks） is investigated. An efficient and concise method for the complex multiply connected region is developed, with which explicit series form solutions of the complex potentials in the matrix, and the interphase layer and inclusion regions are derived. Based on the complex potentials, the image force on the screw dislocation is then calculated by using the Peach-Koehler formula. The equilibrium position of the dislocation is discussed in detail for various rigid line geometries, interphase layer thicknesses and material property combinations. The main results show that the interracial rigid lines exert a significant perturbation effect on the motion of the screw dislocation near the circular inclusion surrounded by an interphase layer.     

INTERACTION OF A DISLOCATION DIPOLE WITH A MODE III INTERFACE CRACK

Interaction between a screw dislocation dipole and a mode III interface crack is investigated. By using the complex variable method, the closed form solutions for complex potentials are obtained when a screw dislocation dipole lies inside a medium. The stress fields and the stress intensity factors at the tip of the interface crack produced by the screw dislocation dipole are given. The influence of the orientation, the dipole arm and the location of the screw dislocation dipole as well as the material mismatch on the stress intensity factors is discussed. The image force and the image torque acting on the screw dislocation dipole center are also calculated. The mechanical equilibrium position of the screw dislocation dipole is examined for various material property combinations and crack geometries. The results indicate that the shielding or anti-shielding effect on the stress intensity factor increases abruptly when the dislocation dipole approaches the tip of the crack. Additionally, the disturbation of the interface crack on the motion of the dislocation dipole is also significant.     

INTERACTION OF A DISLOCATION DIPOLE WITH A MODE Ⅲ INTERFACE CRACK

Interaction between a screw dislocation dipole and a mode Ⅲ interface crack is investigated. By using the complex variable method, the closed form solutions for complex potentials are obtained when a screw dislocation dipole lies inside a medium. The stress fields and the stress intensity factors at the tip of the interface crack produced by the screw dislocation dipole are given. The influence of the orientation, the dipole arm and the location of the screw dislocation dipole as well as the material mismatch on the stress intensity factors is discussed. zThe image force and the image torque acting on the screw dislocation dipole center are also calculated. The mechanical equilibrium position of the screw dislocation dipole is examined for various material property combinations and crack geometries. The results indicate that the shielding or anti-shielding effect on the stress intensity factor increases abruptly when the dislocation dipole approaches the tip of the crack. Additionally, the disturbation of the interface crack on the motion of the dislocation dipole is also significant.