稀土固体超强酸SO4^2-／TiO2-La^3＋催化硝化甲苯的研究

研究了以固体超强酸SO24-/TiO2-La3 作为催化剂,浓硝酸和甲苯为原料合成硝基甲苯,并考察了影响反应的因素。结果表明,催化剂用浓度为1.0 mol.L-1硫酸浸泡3小时,反应催化剂用量为硝酸质量的10%,反应时间为3小时,反应温度为55℃是最适宜的反应条件,甲苯转化率达90.14%,邻对比达0.89。     

稀土固体超强酸SO_4~(2-)/TiO_2-La~(3+)催化硝化甲苯的研究

研究了以固体超强酸SO24-/TiO2-La3+作为催化剂,浓硝酸和甲苯为原料合成硝基甲苯,并考察了影响反应的因素。结果表明,催化剂用浓度为1.0 mol.L-1硫酸浸泡3小时,反应催化剂用量为硝酸质量的10%,反应时间为3小时,反应温度为55℃是最适宜的反应条件,甲苯转化率达90.14%,邻对比达0.89。     

三氟甲磺酸盐催化甲苯硝化反应的研究

利用三氟甲磺酸盐作为新型的Lewis酸催化剂, 用于甲苯与等物质的量的硝酸的硝化反应. 通过对不同催化剂进行考察发现Zr(OTf)₄和Sm(OTf)₃的催化性能最好, 甲苯转化率分别达77.1%和67.4%. 使用98%硝酸能使转化率达100%, 而用甲苯作溶剂时转化率达95.4%. 对硅胶负载催化剂的考察发现硅胶负载催化剂Sm(OTf)₃能使甲苯转化率升至89.9%, 且异构体分布有所改变, 其o∶m∶p为44.6∶5.7∶49.7.     

硫酸氢钠催化下甲苯的硝化

研究了硫酸氢钠催化下甲苯用硝酸的硝化.结果表明,在醋酐存在条件下,以CCl4为溶剂,以质量分数为95%的硝酸为硝化剂,反应温度控制在45℃,反应进行60 min,选用硫酸氢钠催化剂.对甲苯表现出了强的区域选择性,甲苯硝化产物邻对位比达1.09,较硝酸硫酸混酸的1.67显著降低.硝化产物收率达到99.9%.催化剂可循环使用5次,催化活性基本不变,是一种极具工业化开发价值的硝化反应催化剂.     

FeZSM-5/N2O体系催化氧化甲苯制甲酚的研究

采用四丙基氢氧化铵为模板剂, 硝酸铁为铁源应用水热合成法制备了一系列FeZSM-5分子筛催化剂, 利用X-射线粉末衍射分析, N2吸附/脱附, 元素分析等技术对催化剂进行了表征. 并进行了所制样品对甲苯催化氧化制甲酚反应催化性能的研究. 本文详细考察了Fe含量、反应物配比、反应温度以及空速等各种因素对甲苯催化氧化制甲酚反应催化性能的影响. 结果表明在400 ℃, 甲苯∶N2O为1∶4, 空速为8 000 mL·h-1·g-1条件下反应结果最佳, 最大甲苯转化率约为12.6%, 甲酚选择性约为33.0%.     

负载型杂多酸催化下N2O5对甲苯的选择性硝化

用负载型杂多酸为催化剂,N2O5为硝化剂的新型硝化体系,对甲苯的硝化反应进行研究. 分别考察了杂多酸类型、载体种类、杂多酸负载量及催化剂循环使用次数等因素对硝化反应的影响. 结果证明,负载型杂多酸能显著提高N2O5的硝化能力;催化剂回收后可直接重复使用,甲苯硝化反应得率为34%,对位选择性达到58.9%,表明N2O5是一种具有应用前景的硝化试剂.     

固体铌酸催化下甲苯的硝化

在不同焙烧温度下制备了一系列固体铌酸催化剂。测定了固体铌酸催化剂的比表面积、表面酸强度及表面酸量。研究了催化剂焙烧温度、硝化反应时间、硝化反应温度、有无醋酐存在、硝酸浓度、催化剂的重复使用等因素对甲苯硝化反应影响。实验结果表明,当反应温度为40℃,反应时间为60 min时,以CCl4为溶剂,以质量分数为95%的硝酸为硝化剂,在醋酐存在条件下,以经300℃焙烧3 h后的铌酸作为催化剂,甲苯硝化产物中异构体的邻对比达1.26,较硝硫混酸的1.67显著降低,产物得率达99.3%。且该催化剂循环使用5次,催化活性基本不变,是一种极具应用前景的绿色硝化反应催化剂。     

苯乙烯在TiO2／SiO2催化剂上氧化制苯甲醛的研究

在TiO2/S iO2催化的苯乙烯氧化反应中采用空气作为氧化剂,苯乙烯被氧化,生成的苯甲醛和甲醛为主要产物.反应可以在低于100℃的温和条件下进行.在较低的苯乙烯转化率(18.0%)下,可以得到较高的苯甲醛选择性(95.0%).对于此反应,苯乙烯的转化率随催化剂中TiO2含量的增加而增加,但是苯甲醛的选择性随苯乙烯的转化率升高而下降.反应中还考察了加入的溶剂甲苯的体积含量、空气流速、液体流速和催化剂焙烧温度对该氧化反应的影响.在一定的反应条件下,实验发现加入甲苯的体积含量在20%时存在一个最佳值;空气的空速对反应的影响存在极限值,当空气的空速大于一定值(571 mL/g.h)时,不再影响反应的转化率和选择性;一般在液体(苯乙烯和甲苯)的流速增加时,苯乙烯的转化率下降同时苯甲醛的选择性增加.在催化剂的制备过程中,在具有不同TiO2含量的催化剂TiO2/S iO2上,苯乙烯的转化率随TiO2含量增加而增加,此时比表面是影响苯乙烯转化率的次要因素;但是在催化剂的组成相同时,比表面随焙烧温度增加而降低,此时比表面是影响苯乙烯转化率的主要因素,比表面减小导致催化活性降低.     

纳米固体超强酸TiO2/SO42-的制备及其催化甲苯选择性硝化

采用溶胶-凝胶法制备了新型的纳米固体超强酸催化剂TiO2/SO42-,并用XRD、TEM进行了表征。结果表明:所研制的TiO2/SO42-催化剂为晶态纳米粒子,平均粒径为34 nm,分散性较好;以纳米固体超强酸催化剂TiO2/SO42-为催化剂时,甲苯硝化的区域选择性和活性提高。找出最佳反应条件为:催化剂活化温度600℃,反应温度60℃,n(硝酸)/n(甲苯)=2,w(甲苯)/w(催化剂)=35,反应时间4h,甲苯转化率为87.4%,对位硝基甲苯与邻位硝基甲苯之比(P/O)可达1.52。     

负载型Pt/CeO_2-Al_2O_3催化剂的制备及其脱氢性能

通过超声辅助共沉淀法制备了具有高比表面积、大孔容和大孔径的CeO_2-Al_2O_3复合载体,并以此制备了一系列负载型Pt/CeO_2-Al_2O_3催化剂,采用XRD、氮吸附、NH3-TPD、SEM和TEM等方法对复合载体和催化剂进行了表征;以甲基环己烷为模型化合物,考察了Pt/CeO_2-Al_2O_3催化剂的脱氢性能,研究了载体中Ce/Al物质的量比及反应温度对其催化脱氢性能的影响。结果表明,当Ce/Al物质的量比为0.5时,Pt/CeO_2-Al_2O_3催化剂在450℃下具有较高的脱氢性能;甲基环己烷转化率达到88.53%,甲苯的选择性达94.63%。     

Sc2MgGa2 and Y2MgGa2

Scandium magnesium gallide, Sc₂MgGa₂, and yttrium magnesium gallide, Y₂MgGa₂, were synthesized from the corresponding elements by heating under an argon atmosphere in an induction furnace. These intermetallic compounds crystallize in the tetragonal Mo₂FeB₂‐type structure. All three crystallographically unique atoms occupy special positions and the site symmetries of (Sc/Y, Ga) and Mg are m2m and 4/m, respectively. The coordinations around Sc/Y, Mg and Ga are pentagonal (Sc/Y), tetragonal (Mg) and triangular (Ga) prisms, with four (Mg) or three (Ga) additional capping atoms leading to the coordination numbers [10], [8+4] and [6+3], respectively. The crystal structure of Sc₂MgGa₂ was determined from single‐crystal diffraction intensities and the isostructural Y₂MgGa₂ was identified from powder diffraction data.     

Electrochemical study of (NEt4)2Cl2FeS2MoS2 and (NEt4)2Cl2FeS2MoS2FeCl2

Summary The ability of [MoS₄]^2–, anions to be used as ligands for transition metal ions has been widely demonstrated, especially with Fe²⁺. The present study has been restricted to linear complexes such as (NEt₄)₂ [Cl₂FeS₂MoS₂] and (NEt₄)₂[Cl₂FeS₂MoS₂FeCl₂]. Their electrochemical properties are described: upon electrochemical reduction, these compounds yield MoS₂, as a black precipitate, and an iron complex in solution, assumed to be [SFeCl₂]^2–. The electrochemical reduction goes through two electron transfers, coupled with the breakdown of the molecular skeleton: a DISPl and an ECE mechanism. Depending on the solvent, the following equilibrium may be observed: [Cl₄Fe₂MoS₄]^2–[Cl₂FeMoS₄]^2–+FeCl₂. The equilibrium constant, K_D, was evaluated by differential pulse polarography. K_D is tightly related to the donor number of the solvent.     

The alkali hypophosphites KH2PO2, RbH2PO2 and CsH2PO2

The structures of the hypophosphites KH₂PO₂ (potassium hypophosphite), RbH₂PO₂ (rubidium hypophosphite) and CsH₂PO₂ (caesium hypophosphite) have been determined by single‐crystal X‐ray diffraction. The structures consist of layers of alkali cations and hypophosphite anions, with the latter bridging four cations within the same layer. The Rb and Cs hypophosphites are isomorphous.     

Zur Kenntnis der Dialkalimetalldichalkogenide β-Na2S2, K2S2, α-Rb2S2, β-Rb2S2, K2Se2, Rb2Se2, α-K2Te2, β-K2Te2 und Rb2Te2

On Dialkali Metal Dichalcogenides β-Na₂S₂, K₂S₂, α-Rb₂S₂, β-Rb₂S₂, K₂Se₂, Rb₂Se₂, α-K₂Te₂, β-K₂Te₂ and Rb₂Te₂ The first presentation of pure samples of α- and β-Rb₂S₂, α- and β-K₂Te₂, and Rb₂Te₂ is described. Using single crystals of K₂S₂ and K₂Se₂, received by ammonothermal synthesis, the structure of the Na₂O₂ type and by using single crystals of β-Na₂S₂ and β-K₂Te₂ the Li₂O₂ type structure will be refined. By combined investigations with temperature-dependent Guinier-, neutron diffraction-, thermal analysis, and Raman-spectroscopy the nature of the monotropic phase transition from the Na₂O₂ type to the Li₂O₂ type will be explained by means of the examples α-/β-Na₂S₂ and α-/β-K₂Te₂. A further case of dimorphic condition as well as the monotropic phase transition of α- and β-Rb₂S₂ is presented. The existing areas of the structure fields of the dialkali metal dichalcogenides are limited by the model of the polar covalence.     

Formal [(2+2)+2] and [(2+2)+(2+2)] nonconjugated dienediyne cascade cycloadditions

[reaction: see text] Fluoranthene 2 and heptacycle 3 are easily accessible from the reaction of diyne 1 and norbornadiene (NBD) in the presence of the rhodium catalyst. The unusual [(2+2)+(2+2)] adduct 3 was confirmed by the X-ray crystal structure analysis.     

Crystal Structures of [Bu2Sn(O2PPh2)2], [Ph2Sn(O2PPh2)2], and [PhClSn(O2PPh2)OMe]2. Raman Spectra of [Ph2Sn(O2PPh2)2] and [PhClSn(O2PPh2)OMe]2

[(n‐Bu)₂Sn(O₂PPh₂)₂] ( 1 ), and [Ph₂Sn(O₂PPh₂)₂] ( 2 ) have been synthesized by the reactions of R₂SnCl₂ (R=n‐Bu, Ph) with HO₂PPh₂ in Methanol. From the reaction of Ph₂SnCl₂ with diphenylphosphinic acid a third product [PhClSn(O₂PPh₂)OMe]₂ ( 3 ) could be isolated. X‐ray diffraction studies show 1 to crystallize in the monoclinic space group P2₁/c with a = 1303.7(1) pm, b = 2286.9(2) pm, c = 1063.1(1) pm, β = 94.383(6)°, and Z = 4. 2 crystallizes triclinic in the space group , the cell parameters being a = 1293.2(2) pm, b = 1478.5(4) pm, c = 1507.2(3) pm, α = 98.86(3)°, β = 109.63(2)°, γ = 114.88(2)°, and Z = 2. Both compounds form arrays of eight‐membered rings (SnOPO)₂ linked at the tin atoms to form chains of infinite length. The dimer 3 consists of a like ring, in which the tin atoms are bridged by methoxo groups. It crystallizes triclinic in space group with a = 946.4(1) pm, b = 963.7(1) pm, c = 1174.2(1) pm, α = 82.495(6)°, β = 66.451(6)°, γ = 74.922(6)°, and Z = 1 for the dimer. The Raman spectra of 2 and 3 are given and discussed.     

Die Photoionenspektren von SCl2, S2Cl2 und S2Br2

Photoionization Mass Spectra of SCl₂, S₂Cl₂, and S₂Br₂ Photoionization mass spectra of SCl₂, S₂Cl₂, and S₂Br₂ have been measured. Heats of formation, bond energies, and ionization potentials of fragments have been calculated from appearance potentials.