基于滑动平均的速率偏频激光陀螺静态角速率测量算法

提高速率偏频激光陀螺静态角速率测量精度在其应用领域具有重要的作用.通过对速率偏频激光陀螺随机漂移数据进行分析处理,发现量化噪声对陀螺精度有较大的影响,进而提出了一种基于滑动平均的速率偏频激光陀螺静态角速率测量算法,并进行了理论分析及数值模拟.结果表明,通过合理的选择分组参数,该算法可以有效地降低量化噪声对速率偏频激光陀螺静态角速率测量精度的影响.实验结果也验证了该算法的有效性,可以应用于其它类似需要降低量化噪声的场合.     

支承结构惯量对激光陀螺抖频及精度特性的影响分析

激光陀螺的机抖特性有效克服了陀螺的闭锁效应,是其高精度输出的重要保障。陀螺在不同惯性装置下的抖频会发生变化,这极大地影响了其输出精度,严重制约了激光陀螺在各类惯性装备下的服役能力。从激光陀螺抖动偏频系统入手,对陀螺及其支承结构进行了结构动力学建模及分析,从理论与原理实验两方面论证了支承结构惯量对陀螺抖频特性,乃至陀螺输出精度的影响,分析结果表明,减小支承结构惯量能提高陀螺抖频,进而提高其精度。为激光陀螺在惯导装备中更好的应用起到了指导作用。     

激光陀螺抖动偏频优化研究

基于频率调制理论,分析、仿真计算了正弦抖动偏频和优化后的正弦抖动偏频条件下,激光陀螺输入-输出曲线的特点.结果表明：正弦抖动偏频时激光陀螺的输入-输出曲线在抖动频率的倍频点处存在着动态锁区,其宽度与激光陀螺静态锁区、抖动角振幅有关.采用优化后的正弦抖动偏频可以很好地克服动态锁区,大大提高激光陀螺输入-输出曲线的线性度.试验对比了正弦抖动偏频和优化后的正弦抖动偏频条件下激光陀螺的输出性能.试验结果表明：采用优化后的正弦抖动偏频显著提高了陀螺准确度.     

四频差动激光陀螺工作点的选择

当四频差动激光陀螺工作于增益曲线上左、右旋陀螺比例因子相等位置时,误差因素在拍频的差动中得到较好的抵消,因而具有较优的性能。为了从实验上寻找该最佳工作点,对四频差动激光陀螺拍频表达式进行了分析,发现静态下和频的电压扫描曲线呈抛物线变化,而且当左、右旋陀螺比例因子相等时,和频的电压扫描曲线处于转折点。设计了实验通过和频电压扫描曲线得到了理论最佳工作点,在不同工作点下对陀螺进行测试,根据其零偏稳定性随工作点的变化趋势,得到了实测最佳工作点。对某型5个陀螺的多次实验表明,由和频电压扫描曲线得到的理论最佳工作点与实测最佳工作点基本一致,最大误差2Hz。该方法可作为四频陀螺选择最佳工作点的参考方法。     

抖动偏频激光陀螺速率阈值特性研究

本文从理论上分析了正弦抖动偏频激光陀螺速率阈值特性,提出了一种用于测试抖动偏频激光陀螺速率阈值的试验方案,结果表明激光陀螺在零速率处存在与理论相符合的小死区,动态锁区值与陀螺速率阈值具有确定的对应关系。     

抖动偏频激光陀螺速率阈值特性研究

本文从理论上分析了正弦抖动偏频激光陀螺速率阈值特性,提出了一种用于测试抖〖ZH(〗动偏频激光陀螺速率阈值的试验方案结果表明激光陀螺在零速率处存在与理论相符合的小死区,动态锁区值与陀螺速率阈值具有确定的对应关系     

二频机抖激光陀螺零偏的温度特性的逐步回归分析

研究了二频机抖激光陀螺的零偏的温度特性。通过重复性温度实验,利用逐步回归法分析了机抖激光陀螺零偏与温度的关系,得到了零偏的实时温度补偿模型。结果表明,二频机抖激光陀螺的零偏和温度、温度速率具有较好的线性关系和重复性,可以通过温度补偿来提高陀螺的精度。     

四频激光陀螺不同工作模式下零漂的高低温性能分析

四频激光陀螺光强稳定控制后两种不同模式下的零漂在高低温实验中表现出非常明显的差异,其中一种模式的零漂在温度单方向变化时存在一定的振荡,而另一种模式的零漂与温度基本上是线性关系,并且具有良好的重复性。针对这一现象,根据四频激光陀螺的基本理论,分析得出导致这种高低温下不同模式零漂随温度变化不同的主要物理根源可能是差损零漂项和恒磁偏频零漂项随温度变化关系的不同。同时指出四频激光陀螺如果采用温度补偿来提高其精度,则温补系数必须在实际使用的模式下确定才有意义。     

异面腔四频差动激光陀螺的色散平衡

为了减小异面腔四频差动激光陀螺(DLG)腔长变动导致的零漂,对DLG的色散平衡进行了研究.利用气体激光的经典理论,推导了DLG零偏与工作点和轴向磁场的函数关系,给出了色散平衡的理论证明.利用在DLG增益管上缠绕通电线圈,给增益介质施加大小可控的轴向磁场,通过驱动腔平移镜上的压电换能器调节腔长来改变工作点,做出了零偏随腔长和线圈电流的变化曲线.结果表明,零偏对腔长变化的灵敏度是轴向磁场的函数,当增益曲线的塞曼分裂量等于非互易分裂量时零偏对腔长变动不敏感.色散平衡技术减小了腔变动对DLG的影响,有利于提高DLG精度.     

增损比对激光陀螺影响的研究

光强调谐曲线是激光陀螺工作模式选取和稳频的依据,而陀螺的增损比将直接决定光强调谐曲线的形式.为了提高陀螺准确度,本文对双同位素综合展宽情况下二频激光陀螺出光带宽与增损比之间的关系进行了分析计算,结果表明,激光陀螺的出光带宽与增损比之间存在单调递增的变化关系.数值仿真了不同增损比情况下陀螺的光强调谐曲线,结果表明,根据激光陀螺出光带宽与相邻纵横间隔相对大小的不同,其光强调谐曲线的形状可分三种,仿真与试验结果非常吻合.分析并试验验证了增损比选取不当对激光陀螺工程化应用可能产生的影响,给出了不同腔长情况下激光陀螺增损比合理选取的参考值,即应保证陀螺的出光带宽约等于其相邻纵横间隔.     

Absorption transition of He-Ne laser in Plasma generated by microwave

Plasma luminescence has been measured in the visible range from 200 to 800 nm. The effect of collisions with sputtered copper ionic species at different argon gas pressures on the emission light intensity has been studied. The behaviour of well resolved lines at 210 and 657 nm as a function of gas pressure and microwave radiation power is measured. The transmission of He-Ne laser line (632.8 nm) through the induced plasma shows dependence on the microwave radiation power. There are observed transitions for the absorption of laser intensity for the filling gas pressures 0 and 5.3 torr at the radiation power of 175 W.     

An intermittent frequency offset lock of a transverse Zeeman laser to an iodine stabilized He-Ne laser

A single-mode frequency stabilized laser with modulation-free and moderate power is desired as a light source for an ultra-high resolution interferometer system and/or a rapid laser calibration system. For this purpose, we developed a new stabilized laser system that utilizes intermittent control of a 2 mW transverse Zeeman stabilized He-Ne laser (Zeeman laser) with an iodine stabilized He-Ne laser (I2 stabilized laser). Because of the intermittent control, working time of the I2 stabilized laser is reduced. The Zeeman laser has two operational modes: independent and slave mode. In the independent mode, the Zeeman laser is stabilized through control of Zeeman beat frequency. Temperature dependent drift of the oscillation frequency during the independent mode is periodically corrected by the slave operation utilizing frequency offset locking to the I2 stabilized laser. Frequency instability of the Zeeman laser in independent and slave modes is 7.7X10-11 and 2.0X10-11, respectively, at the sampling time of 100 s.     

Absorber-induced features in the ac response of a He-Ne laser

The theoretically predicted pronounced ac-response of the laser intensity to the excitation current modulation of an intracavity saturable absorber has been experimentally verified in a He-Ne laser with a Ne-absorber. Good qualitative agreement with the theory is obtained.     

抽运光强度对光学抽运重水气体产生THz激光的影响分析

利用半经典理论，对脉冲光学抽运重水气体产生THz激光信号过程进行分析，对其中抽运光强度与输出THz信号光之间的关系进行了数值计算和求解，结果表明，THz信号出射光强度跟抽运源入射光强度之间不满足简单的线性关系，而是呈现高阶的非线性关系.在工作介质腔长、气压和工作温度一定的条件下，存在最佳抽运光强度，在一定的抽运光强范围内，THz信号出射光强度与抽运源入射光强度的关系呈现近似线性的增长关系，抽运光能量和信号光能量之间的转换效率相对较高，当抽运光强超过一定值时，由于瓶颈效应的发生会导致THz输出信号的逐步减弱，并产生一定的频率调谐范围.     

Uniphase1007型He—Ne激光管的纵向塞曼稳频研究

本文介绍采用拍频曲线晶振基准法首次在Uniphase 1007型长寿命商品He-Ne激光管上实现了无压电陶瓷调谐元件的塞曼双频稳频,采用可调永磁供磁,达到光频长期漂移5×10~(-9);双频双线偏振分离度1/60;双线偏振正交度89.5°;入锁及锁定情况良好.给出了塞曼双频激光器的调试技术.描述了输出光束偏振状态和纵模数关系的一个物理现象.     

Interference of light beams modulated in anti-phase

A double slit experiment has been performed in which the condition that only one slit was open at any instant of time was satisfied approximately. The intensity of the light was such that (a) the time between the detection of successive photons contributing to any fringe was much less than the transit time of the photons through the interferometer, and (b) the electro-optic shutters were switched several times between the detection of quanta. The light source used was a He-Ne laser and the modulation was obtained using a single ADP crystal. The theoretical background to the experimental method is given and the experimental results are shown.     

Long time relaxation effect of liquid castor oil under high pressure conditions

Abstract

The relaxation times of Liquid castor oil have been investigated by observing the scattered light of a He-Ne gas laser during the slow or rapid application of pressure up to 0.7 GPa at 293 K. For the application of pressure above 0.36 GPa the strong increase of the scattered light intensity approximately by a factor of 10² has been observed 12 hours after an application of pressure. This pressure effect is also observed for subsequent pressure cycles, i.e., the pressure effect is reversible. Experimental results are interpreted according to a model of a liquid of long rod molecules.     

横向Zeeman He—Ne激光器中非线性混频效应的理论

本文在文献[1]的基础上,考虑了原子速度的Maxwell分布,利用矢量场模型和Lamb半经典理论,研究了横向Zeeman He-Ne激光器中近简并四波混频效应,给出了高阶非线性项的计算公式,从理论上解释了拍频曲线畸变的物理原因。并利用计算机进行了数值求解,结果表明本文的理论预言与实验结果相符。 关键词：     

Thermally stable optical cavities for Zeeman laser gyroscopes

The problem of increasing the working time of a Zeeman laser gyroscope (LG) without any discontinuities in the output data is considered. It is proposed to solve it using materials with very small linear temperature expansion coefficients in the LG design and apply piezoelectric correctors with passive temperature compensation. Numerous experimental studies of the perimeter drift have been performed for different Zeeman LG samples. The linear temperature expansion coefficients of the material of LG single blocks have been carried out, and the piezoelectric corrector design has been improved.     

蒸气压对激光辐照靶材烧蚀速率的影响

研究了强激光辐照碳/碳复合材料靶材引起的烧蚀现象及蒸气压对烧蚀速率的影响。基于傅里叶定律,建立了强激光辐照靶材的热传导模型,模拟了忽略蒸气压影响时烧蚀速率随功率的变化;通过Mott-smith近似方法描述了Knudsen层间断区域,分析了间断两侧表面粒子状态参数;结合质量连续方程和蒸气压与温度关系方程,并由气体状态方程描述蒸气流状态,对蒸气压条件下激光烧蚀碳/碳复合材料靶材的速率随功率变化的关系进行了数值模拟。结果表明,在高能激光对靶材的烧蚀过程中,蒸气压力变化会导致靶材的饱和蒸气温度发生变化,进而影响烧蚀速率且使其随功率呈非线性变化,与忽略蒸气压作用时的线性变化规律相差较大,从理论上解释了忽略蒸气压导致的实验数据与理论结果的差异。