Studies of poly(vinylidene fluoride)/poly(vinyl pyrrolidone) blends. I. Thermal transitions by differential scanning calorimetry

Thermal measurements were carried out to investigate the macrostructure of as-cast poly(vinylidene fluoride) (PVDF)/poly(vinyl pyrrolidone) (PVP) blends. At high PVP content, above about 70 wt.%, the two components form a homogeneously mixed amorphous phase whose T_g varies with composition. Crystals are formed upon casting mixtures richer in PVDF; these systems exhibit complex thermal behavior that cannot be justified by a simple two-phase model. DSC measurements above room temperature on semicrystalline blends show, in addition to the melting of PVDF crystals at temperatures that decrease on increasing PVP content, a glass transition at about 80°C, independent of composition. Experimental results strongly support the hypothesis that an interphase, composed of essentially undiluted noncrystalline PVDF, is always associated with the lamellar crystals.     

Miscibility and thermal stability of poly(vinyl alcohol)/chitosan mixtures

The miscibility and the thermal behaviour of chitosan acetate (ChA) with poly(vinyl alcohol) (PVA) have been investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). Chitosan is blended with poly(vinyl alcohol) in acetic acid solution and this solution is cast to prepare the blend film. From thermal curves the thermal transitions: T_g, T_m and characteristic temperatures of decomposition: T_di, T_max have been determined and compared. The influence of the degree of PVA hydrolysis on the thermal properties of blend systems has been discussed.Based upon the observation on the DSC analysis, the melting point of PVA is decreased when the amount of ChA in the blend film is increased. Though some broadening of the transition curves could be noticed (DSC, TGA and DMA), the obtained results suggest that in the solid ChA/PVA blends the components are poorly miscible. Only PVA sample with relatively low DH = 88% and hence low degree of crystallinity shows partial miscibility with ChA of relatively low molecular weight.     

Thermal characterization and solid‐state 13C‐NMR investigation of blends of poly(N‐phenyl‐2‐hydroxytrimethylene amine) and poly(N‐vinyl pyrrolidone)

The miscibility and thermal properties of poly(N‐phenyl‐2‐hydroxytrimethylene amine)/poly(N‐vinyl pyrrolidone) (PHA/PVP) blends were examined by using differential scanning calorimetry (DSC), high‐resolution solid‐state nuclear magnetic resonance (NMR) techniques, and thermogravimetric analysis (TGA). It was found that PHA is miscible with PVP, as shown by the existence of a single composition‐dependent glass transition temperature (T_g) in the whole composition range. The DSC results, together with the ¹³C crosspolarization (CP)/magic angle spinning (MAS)/high‐power dipolar decoupling (DD) spectra of the blends, revealed that there exist rather strong intermolecular interactions between PHA and PVP. The increase in hydrogen bonding and in T_g of the blends was found to broaden the line width of CH—OH carbon resonance of PHA. The measurement of the relaxation time showed that the PHA/PVP blends are homogeneous at least on the scale of 1–2 nm. The proton spin‐lattice relaxation in both the laboratory frame and the rotating frame were studied as a function of the blend composition, and it was found that blending did not appreciably affect the spectral densities of motion (sub‐T_g relaxation) in the mid‐MHz and mid‐KHz frequency ranges. Thermogravimetric analysis showed that PHA has rather good thermal stability, and the thermal stability of the blend can be further improved with increasing PVP content. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 237–245, 1999     

Miscibility and ferroelectric behavior in blends of poly(vinylidene fluoride/trifluoroethylene) and poly(vinyl acetate)

The blend system containing a poly(vinylidene fluoride/trifluoroethylene) [P(VDF/TrFE)] copolymer (68/32 mol %) and poly(vinyl acetate) (PVAc) was miscible from the results of differential scanning calorimetry (DSC) studies that exhibit the presence of a single, composition‐dependent glass transition temperature (T_g) and a strong melting point depression for the semicrystalline P(VDF/TrFE) component. However, differences between the DSC and dielectric measurements, which showed a separate P(VDF/TrFE) T_g peak, suggests that the P(VDF/TrFE)/PVAc blends are actually partially miscible. Because of the lower dielectric constant of PVAc and the reduced sample crystallinity caused by the addition of PVAc, both the dielectric constant and the remanent polarization of the copolymer blends decrease with increasing PVAc content. The presence of a small amount of PVAc stabilized the anomalous ferroelectric behavior of ice–water‐quenched P(VDF/TrFE), and the blend portrayed normal polarization reversal behavior after adding only 1 wt % PVAc. The piezoelectric response suggests small changes with an increasing number of poling cycles. It is believed that PVAc affects the D‐E hysteresis behavior at the interface between crystalline and amorphous phases, although much work remains to be done to confirm this hypothesis. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 927–935, 2003     

Mechanical properties and morphology of epoxy/poly(vinyl acetate)/poly(4-vinyl phenol) brominated system

Diglycidyl ether of bisfenol-A (DGEBA)/poly(vinyl acetate) (PVAc)/poly(4-vinyl phenol) brominated (PVPhBr) ternary blends cured with 4,4’-diaminodiphenylmethane (DDM) were investigated by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). Homogeneous (DGEBA+DDM)/PVPhBr networks with a unique T _g are generated. Ternary blends (DGEBA+DDM)/PVAc/PVPhBr are initially miscible and phase separate upon curing arising two T _gs that correspond to a PVAc-rich phase and to epoxy network phase. Increasing the PVPhBr content the T _gof the PVAc phase move to higher temperatures as a consequence of the PVAc-PVPhBr interactions. Different morphologies are generated as a function of the blend composition.     

The miscibility of poly(vinyl alcohol)/poly(N-vinylpyrrolidone) blends investigated in dilute solutions and solids

Poly(vinyl alcohol) (PVA) (polymer A) and poly(N-vinylpyrrolidone) (PVP) (polymer B) are known to form a thermodynamically miscible pair. In the present study the conclusion on miscibility of PVA/PVP solid blends, confirmed qualitatively (DMTA, FTIR) and quantitatively (DSC, χ_AB = − 0.69 at 503 K) is compared with the miscibility investigations of PVA/PVP solution blends by the technique of dilute solution viscometry. The miscibility of the ternary (polymer A/ polymer B/ solvent) system is estimated on the basis of experimental and ideal values of the viscosity parameters k, b and [η]. It is found that the conclusions on miscibility or nonmiscibility drawn from viscosity measurements in dilute solution blends depend: (i) on the applied extrapolation method used for the determination of the viscosity interaction parameters, (ii) on the assumed definition of the ideal values and (iii) on the thermodynamic quality of the solvent, which in the case of PVA depends on its degree of hydrolysis. Hence, viscometric investigations of dilute PVA/PVP solution blends have revealed that viscometry, widely used in the literature for estimation of polymer-polymer miscibility can not be recommended as a sole method to presume the miscibility of a polymer pair.     

A dielectric study of poly(ethylene-co-vinylacetate)–poly(vinyl chloride) blends. I. Miscibility and phase behavior

Measurements of the complex permittivity were used to study miscibility and phase behavior in blends of poly(vinyl chloride) (PVC) with two random ethylene—vinyl acetate (EVA) copolymers containing 45 and 70 wt % of vinyl acetate. The dielectric β relaxation of the pure polymers and blends was followed as a function of temperature and frequency for different blend compositions and thermal treatments. Blends of EVA 70/PVC were found to be miscible for compositions of about 25% EVA 70 and higher. Blends of lower EVA 70 content showed evidence of two-phase behavior. EVA 45/PVC blends were found to be miscible only at the composition extremes; at intermediate compositions these blends were two-phase, partially miscible. Both blend systems showed lower critical solution temperature behavior. Phase separation studies revealed that in the EVA 45/PVC blends, PVC was capable of diffusing into the higher T_g phase at temperatures below the T_g of the upper phase. In the blends, ion transport losses were significant above the loss peak temperatures, and in the two-phase systems, often obscured the upper temperature loss process. It was shown possible, however, to correct the loss curves for this transport contribution.     

Miscible blends of poly(ethylene oxide) with brush copolymers of poly(vinyl alcohol)‐graft‐poly(l‐lactide)

Even though poly(ethylene oxide) (PEO) is immiscible with both poly(l ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA), this article shows a working route to obtain miscible blends based on these polymers. The miscibility of these polymers has been analyzed using the solubility parameter approach to choose the proper ratios of the constituents of the blend. Then, PVA has been grafted with l ‐lactide (LLA) through ring‐opening polymerization to obtain a poly(vinyl alcohol)‐graft‐poly(l ‐lactide) (PVA‐g‐PLLA) brush copolymer with 82 mol % LLA according to ¹H and ¹³C NMR spectroscopies. PEO has been blended with the PVA‐g‐PLLA brush copolymer and the miscibility of the system has been analyzed by DSC, FTIR, OM, and SEM. The particular architecture of the blends results in DSC traces lacking clearly distinguishable glass transitions that have been explained considering self‐concentration effects (Lodge and McLeish) and the associated concentration fluctuations. Fortunately, the FTIR analysis is conclusive regarding the miscibility and the specific interactions in these systems. Melting point depression analysis suggests that interactions of intermediate strength and PLOM and SEM reveal homogeneous morphologies for the PEO/PVA‐g‐PLLA blends. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1217–1226     

Interpolymer complexation and thermal behaviour of poly(styrene-co-maleic acid)/poly(vinyl pyrrolidone) mixtures

Polymer complexation between poly(styrene-co-maleic acid), (SMA28) and (SMA50) containing 28 and 50 mol% of maleic acid and poly(vinyl pyrrolidone) (PVP), has been investigated by differential scanning calorimeter (DSC), Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). All results showed that the ideal complex composition of SMA28/PVP and SMA50/PVP leads, respectively, to 2:1 and 1:1 mole ratio of interacting components.For the investigated systems, the T_g versus composition curve does not follow any of the usual proposed models for polymer blends. Withal, a new model proposed by Cowie et al. is used to fit the T_g data and it is found to reproduce the experimental results more closely. According to n and q obtained values, it seems reasonable to conclude that the inter-associated hydrogen bonds dominate in SMA28/PVP (2:1) complexes. This effect is corroborated by the FTIR study as evidenced by the high displacement of the specific bands and ionic interactions have been clearly identified. Finally, a thermogravimetric study shows that ionic interactions increase the thermal stability of these complexes.     

Studies of polylactone/poly(vinyl chloride), polylactone/poly(vinyl fluoride), and polylactone/poly(vinylidene fluoride) blends

It is shown that polyvalerolactone/poly(vinyl chloride) (PVL/PVC) blends are miscible over all compositions since a single glass transition temperature T_g is observed, intermediate between those of pure PVL and pure PVC. Melting points, enthalpies of fusion and morphologies of PVL/PVC blends are also reported. It is also shown that polyvalerolactone, poly(α-methyl-α-n-propyl-β-propiolactone), poly(α-methyl-α-ethyl-β-propiolactone), and poly(caprolactone) are immiscible with poly(vinyl fluoride) and poly(vinylidene fluoride), despite the fact that all these polylactones are miscible with PVC. Differences in electronegativity, in atomic radius, and in molar attraction between the fluoride and the chlorine atoms are probably responsible for this difference in behavior.     

Miscible blends containing a crystallizable component: poly(vinyl alcohol)/poly(ethyleneimine)

Blends of poly(vinyl alcohol) (PVAI) with poly(ethyleneimine) (PEI) were prepared by casting from a common solvent. All blends show a single, composition dependent glass transition temperature (T_g), indicating that the blends are miscible in the amorphous state and in the melt. The overall crystallization rate of PVAI in the blend decreases with increasing PEI content. The crystallinity index of PVAI in the blend does not decrease greatly with PEI content up to a composition of 70/30 PVAI/PEI, since the T_g of the crystallizable component PVAI is larger than that of the non-crystallizable component PEI. The T_g of the system PVAI/PEI decreases with increasing PEI content. The interaction parameter B of the two polymers in the melt was found to be −24 J/cm³.     

Effects of amorphous poly(vinyl acetate) on crystalline morphology of poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid)

The amorphous and crystalline phase behavior, spherulite morphology, and interactions between amorphous poly(vinyl acetate) (PVAc) and poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) (PHBV) were examined using differential scanning calorimetry, polarized-light optical and scanning electron, atomic-force microscopy (DSC, POM, SEM, AFM), and small-angle X-ray scattering (SAXS). The PHBV/PVAc blend was found to be miscible with an almost linear T _g-composition relationship, indicating perfect homogeneity. Interaction parameter by melting point depression is a negative value of χ = −0.32, suggesting quite favorable interaction strength. With the intimate interaction between the amorphous PVAc and crystalline PHBV polymers, effects of PVAc on the spherulitic morphology of PHBV are quite significant. Owing to the higher T _g of PVAc (than that of PHBV), the spherulite growth rate of PHBV was depressed by increasing PVAc content in blends. Neat PHBV exhibits ring-banded spherulites when crystallized at T_c = 60 ~ 110^° C {T_{\rm{c}}} = {6}0\sim {11}0^\circ {\hbox{C}} ; however, with increasing PVAc content in the blends, the temperature range at which the PHBV/PVAc blends exhibit ring-banded spherulites remains similar but the regularity increases, and the inter-ring spacing significantly decreases. In addition, the spherulite size and ring-band patterns therein are strongly dependent on T _max (190 vs. 220 °C, respectively, for erasing prior nuclei), from which the blends were quenched to a T _c (60–110 °C) for crystallization. For PHBV/PVAc blends crystallized at the same T _c from different T _max, higher T _max tends to erase nuclei, leading to larger spherulites. However, such larger spherulites owing to higher T _max are not necessarily packed with thicker lamellae.     

Examination of miscibility at molecular level of poly(hydroxyether of bisphenol A)/poly(N-vinyl pyrrolidone) blends by cross-polarization/magic angle spinning 13C nuclear magnetic resonance spectroscopy

The miscibility of poly(hydroxyether of bisphenol A) (phenoxy) and poly(N-vinyl pyrrolidone) (PVP) was investigated by differential scanning calorimetry (DSC) and high-resolution solid-state nuclear magnetic resonance (NMR) techniques. The DSC studies showed that the phenoxy/PVP blends have a single, composition-dependent glass transition temperature (T_g). The S-shaped T_g-composition curve of the phenoxy/PVP blends was reported, which is indicative of the strong intermolecular hydrogen-bonding interactions. To examine the miscibility of the system at molecular level, high-resolution solid-state ¹³C nuclear magnetic resonance (NMR) technique was employed. Upon adding phenoxy to system, the chemical shift of carbonyl carbon resonance of PVP was observed to shift downfield by 1.6 ppm in the ¹³C cross-polarization (CP)/magic angle spinning (MAS) together with the high-power dipolar decoupling (DD) spectra when the concentration of phenoxy is 90 wt %. The observation was responsible for the formation of intermolecular hydrogen bonding. The proton spin-lattice relaxation time T₁(H) and the proton spin-lattice relaxation time in the rotating frame T_1ρ(H) were measured as a function of the blend composition. The T₁(H) result was in good agreement with the thermal analysis, i.e., the blends are completely homogeneous on the scale of 20 ∼ 30 nm. The six results of T_1ρ(H) further indicated that the blends were homogeneous on the scale of 40 ∼ 50Å. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2291–2300, 1998     

Phase behavior and crystallization of a poly(ethylene oxide)/cellulose acetate butyrate blend

The phase behavior of a partially miscible blend of poly(ethylene oxide) (PEO) and cellulose acetate butyrate (CAB) and the crystalline microstructure of PEO in the blend were studied with differential scanning calorimetry (DSC), optical microscopy, and synchrotron small‐angle X‐ray scattering (SAXS) methods. PEO/CAB showed a lower critical solution temperature (LCST) of 168 °C at the critical composition of PEO of 60 wt %. All blend compositions showed a single glass‐transition temperature (T_g) when they were prepared at temperatures lower than the LCST. However, with increasing CAB content, T_g of the blend changed abruptly at 70 wt % CAB; that is, a cusp existed. Below 70 wt % CAB, the change in T_g with blend composition was predicted by the Brau–Kovacs equation, whereas this change was predicted by the Fox equation at higher CAB contents. A gradual but small depression of the melting point of PEO in the blend with an increasing amount of CAB suggested that the PEO/CAB blends exhibited a weak intermolecular interaction. From DSC and SAXS experiments, it was found that amorphous CAB was incorporated into the interlamellar region of PEO for blends with less than 20 wt % CAB, whereas it was segregated to exist in the interfibrillar region in PEO for other blends with larger amounts of CAB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1673–1681, 2002     

Miscibility of poly(styrene‐co‐butyl acrylate) with poly(ethyl methacrylate): Existence of both UCST and LCST

A miscible homopolymer–copolymer pair viz., poly(ethyl methacrylate) (PEMA)–poly(styrene‐co‐butyl acrylate) (SBA) is reported. The miscibility has been studied using differential scanning calorimetry. While 1 : 1 (w/w) blends with SBA containing 23 and 34 wt % styrene (ST) become miscible only above 225 and 185 °C respectively indicating existence of UCST, those with SBA containing 63 wt % ST is miscible at the lowest mixing temperature (i.e., T_g's) but become immiscible when heated at ca 250 °C indicating the existence of LCST. Miscibility for blends with SBA of still higher ST content could not be determined by this method because of the closeness of the T_g's of the components. The miscibility window at 230 °C refers to the two copolymer compositions of which one with the lower ST content is near the UCST, while the other with the higher ST content is near the LCST. Using these compositions and the mean field theory binary interaction parameters between the monomer residues have been calculated. The values are χ_ST‐BA = 0.087 and χ_EMA‐BA = 0.013 at 230 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 369–375, 2000     

Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(trimethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6-naphthalate)/poly(trimethylene terephthalate)/poly(ether imide) (PEN/PTT/PEI) blends were investigated by using a differential scanning calorimeter (DSC), optical microscopy (OM), wide-angle X-ray diffraction (WAXD), and proton nuclear magnetic resonance (¹H-NMR). In the ternary blends, OM and DSC results indicated immiscible properties for polyester-rich compositions of PEN/PTT/PEI blends, but all compositions of the ternary blends were phase homogeneous after heat treatment at 300 °C for more than 30 min. An amorphous blend with a single T _g was obtained in the final state, when samples were annealed at 300 °C. Experimental results from ¹H-NMR identified the production of PEN/PTT copolymers by so-called “transesterification”. The influence of transesterification on the behaviors of glass transition and crystallization was discussed in detail. Study results identified that a random copolymer promoted the miscibility of the ternary blends. The critical block lengths for both PEN and PTT hindered the formation of crystals in the ternary blends. Finally, the transesterification product of PEN/PTT blends, ENTT, was blended with PEI. The results for DSC and OM demonstrated the miscibility of the ENTT/PEI blends.     

Fabrication and characterization of transparent and biodegradable cellulose/poly (vinyl alcohol) blend films using an ionic liquid

Biodegradable blends were prepared from cellulose and poly (vinyl alcohol) (PVA) using the ionic liquid (IL) solvent, 1-butyl-3-methylimidazolium chloride. The blends were regenerated into films, fibers and rectangular blocks. The films showed optical transparency throughout the entire composition of the blends. The infrared spectroscopic experiments proved the existence of intermolecular hydrogen bonding interactions between the hydroxyl groups of cellulose and PVA. The miscibility between cellulose and PVA lead to increase in glass transition temperature (T _g) and of decrease in crystallinity of the blends. The T _g-composition data showed a negative deviation from Fox predictions, however fit well with BCKV model. The addition of PVA improved the tensile strength and elongation at break, considerably plasticizing cellulose. The blends can be degraded completely in soil. Moreover, the IL was completely recycled with high yield after the processing.     

Preparation and Characterization of Blend Films of Poly(Vinyl Alcohol) and Sodium Alginate

Blend films of poly(vinyl alcohol) (PVA) and sodium alginate (NaAlg) were prepared by casting from aqueous solutions. This blend films were characterized by tensile strength test, Fourier transform infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The miscibility in the blends of PVA and NaAlg was established on the basis of the thermal analysis results. DSC showed that the blends possessed single, composition‐dependent glass transition temperatures (T_gs), indicating that the blends are miscible. FT‐IR studies indicate that there is the intermolecular hydrogen bonding interactions, i.e. –OH…^?OOC– in PVA/NaAlg blends. The blend films also exhibited the higher thermal stability and their mechanical properties improved compared to those of homopolymers.     

Miscibility and phase structure of binary blends of polylactide and poly(methyl methacrylate)

Blends of amorphous poly(DL‐lactide) (DL‐PLA) and crystalline poly(L‐lactide) (PLLA) with poly(methyl methacrylate) (PMMA) were prepared by both solution/precipitation and solution‐casting film methods. The miscibility, crystallization behavior, and component interaction of these blends were examined by differential scanning calorimetry. Only one glass‐transition temperature (T_g) was found in the DL‐PLA/PMMA solution/precipitation blends, indicating miscibility in this system. Two isolated T_g's appeared in the DL‐PLA/PMMA solution‐casting film blends, suggesting two segregated phases in the blend system, but evidence showed that two components were partially miscible. In the PLLA/PMMA blend, the crystallization of PLLA was greatly restricted by amorphous PMMA. Once the thermal history of the blend was destroyed, PLLA and PMMA were miscible. The T_g composition relationship for both DL‐PLA/PMMA and PLLA/PMMA miscible systems obeyed the Gordon–Taylor equation. Experiment results indicated that there is no more favorable trend of DL‐PLA to form miscible blends with PMMA than PLLA when PLLA is in the amorphous state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 23–30, 2003     

Mechano-optical behavior in poly (ethylene terephthalate)/poly (ether imide) blends

Mechano-optical behavior and related structural evolution during uniaxial stretching of melt miscible poly (ethylene terephthalate) (PET)/poly (ether imide) (PEI) blends were studied near their glass transition temperature using an instrumented machine that measures true stress, true strain and spectral birefringence simultaneously. Stretching from amorphous state, two distinct stress-optical regimes were observed at temperatures between T_g and T_cc (cold crystallization). Near T_g, a typical photoelastic behavior persists until a critical temperature above which temperature independent initial stress optical behavior is observed. At those temperatures above T_g, where glassy behavior is observed, decreasing stretching rate was also found to eliminate this glassy photo elastic regime leading to the observation of a linear initial stress optical behavior that becomes temperature independent as expected from linear stress optical rule. Increasing PEI concentration in the blends suppresses crystallizability and increases temperature at which initial elastic region disappears giving way to pure liquid behavior where linear stress optical behavior is observed. This is attributed to the increase and broadening of the glass transition temperature with the addition of noncrystallizable PEI. In PET/PEI blends, the stress-optical coefficient (SOC), determined in a linear stress optical regime, was found to increase linearly with the increase in PEI concentration.