蓖麻油和聚氧乙基蓖麻油的结构和组成的波谱表征

核磁共振波谱法;质谱法;红外光谱法;蓖麻油和聚氧乙基蓖麻油的结构和组成的波谱表征     

用可再生原料合成聚氨酯脲水分散液——成膜后的结构与性能研究

以不同组成的蓖麻油和二官能度聚醚多元醇 (GE 2 10 )等原料合成了聚氨酯脲 (PUU)水分散液 ,研究了蓖麻油 GE 2 10的组成对PUU膜结构与性能的影响 .结果表明 ,由GE 2 10合成的PUU虽软硬段间存在一定的相容性 ,但其中脲羰基的氢键化程度高 ,硬段形成较好的有序结构 ,导致PUU膜具有较高的拉伸强度及断裂伸长率 ,但弹性模量和硬度下降 .在蓖麻油合成的PUU中脲羰基的氢键化程度及硬段有序结构均受到化学交联结构的抑制 ,故PUU膜的拉伸强度和断裂伸长率降低 ,但弹性模量及硬度较高 .由蓖麻油与GE 2 10在一定的组成范围内合成的PUU膜 ,具有优良的综合平衡的力学性能 ,后者与材料的结构形态相符     

蓖麻油酸钠协同体系中独居石的浮选行为及机制研究

分别研究了独居石在蓖麻油酸钠与油酸钠和苯甲羟肟酸钠组成的二元捕收剂体系中的浮选行为及机制。单矿物试验表明药剂添加顺序对独居石浮选指标有较大影响,组合药剂体系的选别指标要远远超过单一药剂体系,苯甲羟肟酸钠和蓖麻油酸钠二元体系中的金红石回收率要优于油酸钠和蓖麻油酸钠体系。Zeta电位、表面张力、接触角研究结果表明:组合药剂在独居石表面吸附主要有离子间互相促进型吸附和由缔合物引起的多层吸附两大类,离子间的缔合作用及其缔合物的空间构象是影响矿物浮选指标的关键因素。紫外漫反射吸收光谱研究表明独居石在蓖麻油酸钠与油酸钠体系中的回收率大小与带隙变化近似一致,而在蓖麻油酸钠与苯甲羟肟酸钠体系中则成反比例关系,具体原因则有待进一步研究。     

蓖麻油聚氨酯／聚取代乙烯互穿网络聚合物作为带锈涂料及粘合剂的可能性

在室温用氧化还原引发剂将蓖麻油、甲苯二异氰酸酯及取代乙烯合成了蓖麻油聚氨酯／聚取代乙烯互穿网络聚合物（ＩＰＮ），研究了不同组成对带锈铁板搭接剪切强度的影响。指出搭接剪切强度随取代乙烯均聚物的玻璃化温度增加而增。ＮＣＯ／ＯＨ之比愈大，搭接剪切强度也愈大。以蓖麻油聚氨酯／（丙烯腈－苯乙烯）共聚物的反应液作为带锈铁板的涂料，其涂膜性能良好。用扫描电镜观察了此种涂料与带锈铁板的结合状态，并讨论其成因。     

蓖麻油型聚氨酯IPN的结构与性能研究

本文用蓖麻油,甲苯二异氰酸酯和甲基丙烯酸β-羟乙酯组成的加聚型网络(Ⅰ)和蓖麻油,甲苯二异氰酸酯和聚丙二醇组成的缩聚型聚氨酯(Ⅱ),以同步法形成了一组新型的IPN。用动态力学法和固体核磁共振法研究了它们的结构和性能,形成IPN后,力学数据显示出机械强度的提高,动态力学损耗谱上表现出,tanδ的增宽,固体核磁共振谱计算的结果是界面层的比例增高,但界面层比例并不随配比的改变而变化,它揭示出此IPN可能具有壳核结构。     

不同异氰酸酯固化的蓖麻油／酚氧树脂聚氨酯的力学性能

以ＢＦ３·ＯＥｔ２为催化剂，４，４－二羟基二苯基丙烷与环氧氯丙烷反应，生成端羟基的酚氧树脂（Ａ），Ａ与蓖麻油（Ｂ）混合，用３种异氰酸酯（ＴＤＩ、ＩＰＤＩ和ＨＤＩ）作为固化剂，制得交联聚氨酯。研究了这３种聚氨酯的力学性能及形态与组成和二异氰酸酯结构的关系；改变ＮＣＯ／ＯＨ摩尔比及Ｂ与Ａ的质量比，可以制得具有较好力学性能的聚氨酯材料。蓖麻油，酚氧树脂，聚氨酯，力学性能     

COPU／PMMA AB交联聚合物的性能

AB交联聚合物(ABCP)是由聚合物A链与化学组成不同的聚合物B链交联构成。它的网络结构不同于IPN。IPN是由两个独立的网络构成,而在ABCP中仅存在一个聚合物网络。目前人们对它远不及对IPN了解得多。 本文选用蓖麻油为原料,与甲基丙烯酸甲酯共聚,合成了一种ABCP。研究了它的力学性能,转变与松弛,相容性及形态结构与组成及交联密度的关系。     

生物医用蓖麻油基聚氨酯及其接枝改性的研究进展

蓖麻油是价格低廉的可再生资源,含有大量的羟基,可代替聚酯(醚),合成出蓖麻油基聚氨酯,在生物医学领域有着广阔的发展空间。本文阐述了聚氨酯合成方法,分析了结构特性,并对其蓖麻油基聚氨酯接枝改性进行了较详细的探讨。报道了蓖麻油基聚氨酯接枝改性后的生物医用发展趋势。随着组织修复材料的发展,以天然生物质为原料而制备的该种复合生物材料是有广阔的发展前景。     

从蓖麻油制取10-羟基癸酸的研究

本文报道了从蓖麻油制取10-羟基癸酸的研究, 发现了从蓖麻油制取10-羟基癸酸的新的工艺路线和最佳的工艺条件, 用氢氧化钠用量、2-辛醇量、反应时间和反应温度四因子三水平L9(3^4)进行了正交试验, 发现最佳工艺条件是: 氢氧化钠(g)/蓖麻油(g):1.25; 2-辛醇量(g)/蓖麻油(g):2; 反应时间:6h; 反应温度:180℃。在这一新的工艺路线和最佳工艺条件下, 10-羟基癸酸产率可达75%。     

室温固化蓖麻油聚氨酯/乙烯基聚合物互穿网络材料的一些规律及其性能

研究了蓖麻油与甲苯二异氰酸酯及丙烯酸酯或苯乙烯等乙烯基单体在室温下生成的互穿网络聚合物(IPN)的一些规律及其性能.用红外光谱追踪表明,聚氨酯的生成快于甲基丙烯酸甲酯的聚合.研究IPN凝胶点指出.凝胶点时间随聚氨酯含量增加及聚苯乙烯含量减少而缩短.丙烯酸甲酯在生成IPN过程中凝胶的生成速度要比苯乙烯的场合快.丙烯酸丁酯、丙烯腈或丙烯酸甲酯与蓖麻油聚氨酯生成的IPN的抗张强度在聚氨酯占一半时呈现最大值.透射电镜观察表明,生成速率较快的聚氨酯的微区存在于聚丙烯酸甲酯中.聚丙烯酸甲酯与蓖麻油聚氨酯形成的IPN在tanδ-T,曲线上呈现一个宽的玻璃化转变温度.     

STUDY ON CASTOR OIL POLYURETHANE/POLY (METHYL METHACRYLATE) AB CROSSLINKED POLYMERS

Castor oil polyurethane/poly(methyl methacrylate) AB crosslinked polymers (ABCP) were synthesized by free radical copolymerization of MMA and vinyl-terminated castor oil polyurethane which was obtained from isocyanate-terminated castor oil polyurethane and hydroxyethyl methacrylate The mechanical properties, transition and relaxation, as well as compatibility and morphology of the ABCP were investigated by changing the component. The results show that the ABCP is a semicompatible system and the compatibility of the two components decreases with increasing content of the hard segment. The mechanical and damping properties of the ABCP are obviously superior to that of their homopolymers. The damping value is mainly controlled by cross[ink density of the ABCP but the T-g value by component.     

INTERPENETRATING POLYMER NETWORKS BASED ON OIL MODIFIED CASTOR OIL URETHANE AND POLY(METHYL METHACRYLATE)

Castor oil was initially subjected to an interesterification reaction with linseed and tung oils and the resulting intermediate was used for the preparation of polyurethanes and their IPNs with poly(methyl methacrylate). They were characterized for their physico-mechanical, swelling, and thermal properties. The morphologies of IPNs were studied with the aid of scanning electron microscopy and differential scanning calorimetry. On comparing the mechanical properties of castor oil polyurethane (CU) and their IPNs (C-IPNs) with those of the castor oil modified with linseed and tung oil (L-IPN and T-IPN, respectively) it was found that L-IPNs showed higher tensile strength, hardness, and better compatibility than C-IPNs. All IPNs showed synergistic effect in elongation and exhibited similar thermal behavior with no significant change with respect to their composition. However, the castor oil polyurethane and their IPNs showed relatively higher elongation and better resistance to solvents.     

Interpenetrating polymer network from castor oil-based polyurethanes and poly(methyl methacrylate). XV

The polyurethanes have been prepared from 2.12 functional ? OH containing castor oil and diphenyl methane diisocyanate under identical experimental conditions with a varying NCO/OH ratio. These polyurethanes were swollen in methyl methacrylate and subsequently interpenetrated by free radical polymerization using benzoyl peroxide and crosslinker ethylene glycol dimethacrylate. A series of interpenetrating polymer network (IPN) PU/PMMA IPNs were obtained as films by a transfer moulding technique. These IPNs were characterized by their resistance to chemical reagents, thermal behavior, and mechanical properties. The morphology was shown by SEM and dielectric properties at different temperatures were measured.     

结构因素和配位效应对室温本体聚合的影响

考察了丙烯酸乙酯(EA)、甲基丙烯酸甲酯(MMA)、苯乙烯(St)和丙烯腈(AN)四种不同结构特征的乙烯基单体和桐油(TO)、蓖麻油(CO)两种生物质油在室温(25℃)下以氧化还原引发体系引发的本体均聚合和共聚合反应,以及环烷酸钴的配位效应对聚合的影响。结果表明,室温下取代基的供电性或共轭性越强的单取代烯烃逾难均聚合;苯乙烯不能均聚,也不能与丙烯酸乙酯共聚合;由于空间位阻的原因,桐油和蓖麻油的均聚合以及与其它单体的共聚合在常温下均不能进行;环烷酸钴的配位效应能够提高单体和自由基的活性,促进聚合反应进行。     

紫外光固化蓖麻油型聚氨酯-甲基丙烯酸羟乙酯网络聚合物的合成

本工作对蓖麻油/甲苯二异氰酸酯(TDI)/甲基丙烯酸羟乙酯(HEMA)形成的预聚体和不同的活性稀释剂以不同的光敏剂在紫外光照射下的产物进行了红外光谱和力学性能的测定。结果表明:该体系能形成很好的网络聚合物。所有的产品不仅透明度高,而且都具有一定的机械强度,但仍具有两相结构。     

Synthesis and characterization of polyaniline filled PU/PMMA interpenetrating polymer networks

A series of conducting interpenetrating polymer networks (IPNs), are prepared by sequential polymerization of castor oil based polyurethane (PU) with poly(methyl methacrylate) (PMMA) and polyaniline doped with camphor sulphonic acid (PAni)_CSA. The effect of different amount of PAni (varies from 2.5-12.5%) on the properties of PU/PMMA (50/50) IPNs such as electrical properties like conductivity, dielectric constant and dissipation factor; mechanical properties like tensile strength and percentage elongation at break have been reported. (PAni)_CSA filled IPNs shows improved tensile strength than the unfilled IPN system. The thermal stability and surface morphology of unfilled and (PAni)_CSA filled PU/PMMA (50/50) IPN sheets were investigated using a thermogravimetric analyzer (TGA) and a scanning electron microscope (SEM). TGA thermograms of (PAni)_CSA filled PU/PMMA (50/50) IPNs show a three-step thermal degradation process. SEM micrograms of filled PU/PMMA IPN system shows spherulitic structure at higher concentration of (PAni)_CSA.     

Biobased polyurethane adhesive over petroleum based adhesive: Use of renewable resource

This review article is based on the recent trends and development of biobased polyurethane (PU) adhesives from vegetable oil. A detail discussion has been reported about the PU adhesive starting from petroleum based to biobased source. Special attention has been given towards the utilization of castor oil based PU in adhesive technology, due to the wide range of castor oil among all vegetable oil. The appreciable adhesion, mechanical, thermal properties of vegetable oil based PU adhesives were compared with petroleum based PU adhesive, which were utilized to meet the specific application in adhesion industry.