Amphiphilic polymers based on higher alkylene oxides: Synthesis and characterization by different chromatographic techniques

Homopolymers and block copolymers of higher epoxides (butene oxide and hexene oxide) are synthesized using 1-alkanols and polyethylene glycol monomethyl ether (PEG-MME) 1100 as initiators by anionic ring opening polymerization in bulk. Most of the samples were synthesized with controlled microwave heating in sealed vessels. Tri- and tetrablock copolymers with different repeat units in the individual blocks are synthesized by living polymerization with addition of the next monomer after complete consumption of the previous one. The products thus obtained are characterized using size exclusion chromatography (SEC), liquid chromatography under critical conditions (LCCC) and liquid adsorption chromatography (LAC).     

Block Copolymerization of Lactide and an Epoxide Facilitated by a Redox Switchable Iron‐Based Catalyst

A cationic iron(III) complex was active for the polymerization of various epoxides, whereas the analogous neutral iron(II) complex was inactive. Cyclohexene oxide polymerization could be “switched off” upon in situ reduction of the iron(III) catalyst and “switched on” upon in situ oxidation, which is orthogonal to what was observed previously for lactide polymerization. Conducting copolymerization reactions in the presence of both monomers resulted in block copolymers whose identity can be controlled by the oxidation state of the catalyst: selective lactide polymerization was observed in the iron(II) oxidation state and selective epoxide polymerization was observed in the iron(III) oxidation state. Evidence for the formation of block copolymers was obtained from solubility differences, GPC, and DOSY‐NMR studies.     

Tuning the Properties of Ester-Based Degradable Polymers by Inserting Epoxides into Poly(ϵ-caprolactone)

A series of ester-ether copolymers were obtained via the reaction between α,ω-dihydroxyl poly(ϵ-caprolactone) (PCL) and ethylene oxide (EO) or monosubstituted epoxides catalyzed by strong phosphazene bases. The two types of monomeric units were distributed in highly random manners due to the concurrence of epoxide ring-opening and fast transesterification reactions. The substituent of epoxide showed an interesting bidirectional effect on the enzymatic degradability of the copolymer. Compared with PCL, copolymers derived from EO exhibited enhanced hydrophilicity and decreased crystallinity which then resulted in higher degradability. For the copolymers derived from propylene oxide and 1,2-butylene oxide, the hydrophobic alkyl pendant groups also allowed lower crystallinity of the copolymers thus higher degradation rates. However, further enlarging the pendant groups by using styrene oxide or 2-ethylhexyl glycidyl ether caused a decrease in the degradation rate, which might be ascribed to the higher bulkiness hindering the contact of ester groups with lipase.     

Synthesis of polyglycolic acid copolymers from cationic copolymerization of C1 feedstocks and long chain epoxides

Polyglycolic acid (PGA), which is an important biodegradable polymer, can traditionally be synthesized through the ring opening polymerization of glycolide (with mostly using tin octanoate catalyst). Our previous studies revealed that PGA was alternatively synthesized with one-step cationic polymerization of formaldehyde from trioxane and carbonmonoxide (CO), sustainable C1 feedstocks obtainable from biomethanol or biogas. PGA and its copolymers can be mainly used for the biomedical applications due to their biocompatibility and biodegradability. In order to utilize PGA in other marketing materials such as packaging, PGA should be specifically engineered to improve its physical properties by a copolymerization strategy utilizing appropriate comonomers since PGA displays brown or beige color and is not soluble in most organic solvents due to its very high crystallinity. In this study; to improve on the physical properties of PGA, such as melting temperature and solubility, polymerizations of trioxane, CO and a minor amount of epoxides with long side chains were performed under the same reaction condition as PGA homopolymer synthesis (DCM solvent, at 800 psi, with triflic acid catalyst, reaction time of 72 h). The results have shown that optimum polymerizations were achieved at lower reaction temperatures than that of PGA homopolymer synthesis (110 °C versus 170 °C). The melting temperatures of all copolymers are lower, and the colors of the copolymers have become lighter than that of PGA homopolymer. The solubilities of obtained copolymers also increased by increasing side chain length of epoxides in the polymer backbone.     

Synthesis of a novel block copolymer poly(ethylene oxide)‐block‐poly(4‐vinylpyridine) by combination of anionic ring‐opening and controllable free‐radical polymerization

The block copolymer poly(ethylene oxide)‐b‐poly(4‐vinylpyridine) was synthesized by a combination of living anionic ring‐opening polymerization and a controllable radical mechanism. The poly(ethylene oxide) prepolymer with the 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy end group (PEO_T) was first obtained by anionic ring‐opening polymerization of ethylene oxide with sodium 4‐oxy‐2,2,6,6‐tetramethylpiperidinyl‐1‐oxy as the initiator in a homogeneous process. In the polymerization UV and electron spin resonance spectroscopy determined the 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy moiety was left intact. The copolymers were then obtained by radical polymerization of 4‐vinylpyridine in the presence of PEO_T. The polymerization showed a controllable radical mechanism. The desired block copolymers were characterized by gel permeation chromatography, Fourier transform infrared, and NMR spectroscopy in detail. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4404–4409, 2002     

苯乙烯—环氧乙烷嵌段共聚物的阴离子聚合与表征

用二苯甲烷钾为引发剂,阴离子聚合法合成了苯乙烯（Ｓｔ）－环氧乙烷（ＥＯ）嵌段共聚物,并用ＦＴＩＲ,＾１Ｈ－ＮＭＲ,ＳＥＣ,ＷＡＸＤ和动态粘弹谱对共聚物进行了表征。结果表明所得聚合物为分子量可控,窄分布的两嵌段共聚物。     

ε-己内酯与环氧丙烷嵌段共聚合研究

Inoue等用四苯基卟啉(TPP)与εt_2AlCl的作用产物四苯基卟啉氯化铝(TPPAICl)进行环氧乙烷、环氧丙烷(PO)、β-丙内酯的开环聚合与嵌段共聚合已有很多报道,但Inoue近期文章也有己内酯开环聚合的报道,但1986前只用于开丙内酯聚合。所以我们1986年的文章(即本文的文献[2]是最早用此催化剂进行ε-己内酯聚合的。我们用此催化剂进行了CL的开环聚合。至于CL的嵌段共聚合,Endo等报道了用TPPAlCl/甲     

Synergistic interaction of epoxides and N‐vinylcarbazole during photoinitiated cationic polymerization

A kinetic study was conducted of the independent photoinitiated cationic polymerization of a number of epoxide monomers and mixtures of these monomers with N‐vinylcarbazole. The results show that these two different classes of monomers undergo complex synergistic interactions with one another during polymerization. It was demonstrated that N‐vinylcarbazole as well as other carbazoles are efficient photosensitizers for the photolysis of both diaryliodonium and triarylsulfonium salt photoinitiators. In the presence of large amounts of N‐vinylcarbazole, the rates of the cationic ring‐opening photopolymerization of epoxides are markedly accelerated. This effect has been ascribed to a photoinitiated free‐radical chain reaction that results in the oxidation of monomeric and polymeric N‐vinylcarbazole radicals by the onium salt photoinitiators to generate cations. These cations can initiate the ring‐opening polymerization of the epoxides, leading to the production of copolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3697–3709, 2000     

Synthesis of hydrophilic/CO2‐philic poly(ethylene oxide)‐b‐poly(1,1,2,2‐tetrahydroperfluorodecyl acrylate) block copolymers via controlled/living radical polymerizations and their properties in liquid and supercritical CO2

Hydrophilic/CO₂‐philic poly(ethylene oxide)‐b‐poly(1,1,2,2‐tetrahydroperfluorodecyl acrylate) block copolymers were synthesized via reversible addition–fragmentation chain transfer (RAFT) polymerization, iodine transfer polymerization (ITP), and atom transfer radical polymerization (ATRP) in the presence of either degenerative transfer agents or a macroinitiator based on poly(ethylene oxide). In this work, both RAFT and ATRP showed higher efficiency than ITP for the preparation of the expected copolymers. More detailed research was carried out on RAFT, and the living character of the polymerization was confirmed by an ultraviolet (UV) analysis of the ? SC(S)Ph or ? SC(S)S? C₁₂H₂₅ end groups in the polymer chains. The quantitative UV analysis of the copolymers indicated a number‐average molecular weight in good agreement with the value determined by ¹H NMR analysis. The properties of the macromolecular surfactants were investigated through the determination of the cloud points in neat liquid and supercritical CO₂ and through the formation of water‐in‐CO₂ emulsions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2405–2415, 2004     

Electron Transfer Reactions of Radical Anions with TEMPO: A Versatile Route for Transformation of Living Anionic Polymerization into Stable Radical‐Mediated Polymerization

Summary: The possibility of transforming a living anionic polymerization into a stable radical‐mediated radical polymerization (SFRP) was demonstrated. For this purpose, 2,2,6,6‐tetramethylpiperidine‐N‐oxyl (TEMPO) alcoholate, formed by a one‐electron redox reaction between potassium naphthalene and TEMPO, was used to initiate the living anionic polymerization of ethylene oxide (EO). Poly(ethylene oxide) obtained in this way possessed TEMPO terminal units and was subsequently used as an initiator for the SFRP of styrene to give block copolymers.

A one‐electron redox reaction gives rise to TEMPO alcoholate, which is able to initiate the living anionic polymerization of ethylene oxide (EO).     

Synthesis of 1-oxa-2-silacyclopentane derivatives via intramolecular nucleophilic attack at silicon

Metalation of (HSiMe₂)₃CH with lithium diisopropylamide (LDA) in THF gives (HSiMe₂)₃CLi, which reacts with ethylene oxide, propylene oxide, 1,2-epoxy butane, 1,2-epoxy pentane, 1,2-epoxy hexane, and epichlorohydrin to give the corresponding 1-oxa-2-silacyclopentane derivatives. Then, glycidylmethacrylate (GM) random copolymers with styrene (St) (in a 1:1 and 1:3 mol ratio) were synthesized by solution free radical polymerization at 70(±1) °C using α,α′-azobis(isobutyronitrile) (AIBN) as an initiator. Both types of copolymers were treated with (HSiMe₂)₃CLi to give new modified copolymers. The reaction of (HSiMe₂)₃CLi with epoxides on the side chains of the copolymers does not lead to intramolecular nucleophilic attack contrary to simple epoxides. All the products have been characterized by spectroscopic techniques.     

Synthesis of Block Copolymers by Combination of Atom Transfer Radical Polymerization and Visible Light‐Induced Free Radical Promoted Cationic Polymerization

A new synthetic approach for the preparation of block copolymers by mechanistic transformation from atom transfer radical polymerization (ATRP) to visible light‐induced free radical promoted cationic polymerization is described. A series of halide end‐functionalized polystyrenes with different molecular weights synthesized by ATRP were utilized as macro‐coinitiators in dimanganese decacarbonyl [Mn₂(CO)₁₀] mediated free radical promoted cationic photopolymerization of cyclohexene oxide or isobutyl vinyl ether. Precursor polymers and corresponding block copolymers were characterized by spectral, chromatographic, and thermal analyses.     

Selective polymerization of propylene oxide by a tin phosphate coordination polymer

Oligomeric and polymeric polyether polyols, especially poly(propylene oxide), are used for the production of detergents, nonionic surfactants, washing agents, and cleaners, but they are predominantly used in polyurethane production processes. Tin phosphate coordination polymers show good activity in the selective polymerization of epoxides. The catalyst can be easily synthesized by the condensation of tributyl phosphate and butyl tin trichloride. Investigations of this achiral organotin phosphate condensate in the stereoregular polymerization of propylene oxide, including the properties controlling the molecular weight of the resulting poly(propylene oxide) and structural and mechanistic studies, are presented. Additionally, the polymerization of propylene oxide occurs with high activity, no allyl end groups, just a small number of irregularities, and a high percentage of isotacticity (88%) in the polymer. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3032–3041, 2007     

环氧乙烷和环氧丙烷开环聚合*

环氧乙烷和环氧丙烷的开环聚合产物在表面活性剂工业和聚氨酯工业得到了极为广泛的应用.本文综述了近几年来发展的用于环氧乙烷和环氧丙烷开环聚合的各类催化剂体系,分别讨论了各类催化剂体系对环氧乙烷和环氧丙烷的不同作用机制,考察了反应物结构对反应活性和选择性的影响,重点介绍了配位络合催化剂体系在环氧乙烷和环氧丙烷开环聚合反应中的应用,并指出了今后研究的方向.     

Macromolecular Architecture Based on Anionically Prepared Poly(ethylene oxide) Macromonomers

Synthesis of poly(ethylene oxide) (PEO) macromonomers carrying a methacyloyl group in one end, and N, N-dimethyl amino, thiophene, styryl and vinyl ether functional groups in the other end was desribed. The general synthetic strategy is based on the living anionic polymerization of ethylene oxide initiated with functional potassium alcoholates, followed by reaction with methacyloyl chloride. These macromonomers were further utilized in various macromolecular architectures through via concurrent or selective thermal free radical, oxidative and photoinitiated free radical and cationic polymerization methods. The use of this synthetic route to prepare graft copolymers possessing completly and perfectly alternating PEO side chains using charge-transfer-complex polymerization was also demonstrated.     

Anionic copolymerization of hexanelactam with functionalized polyisoprene

Block copolymers of the A‐B‐C‐B‐A type were synthesized for the first time via the activated anionic polymerization of hexanelactam (HL) with Na‐HL as an initiator and macroactivators [or polymeric activators (PACs)] as elastificators for nylon‐6. The PACs were prepared by the functionalization of telechelic hydroxyl‐terminated poly(ethylene oxide)–polyisoprene–poly(ethylene oxide) copolymers with different diisocyanates. Hexamethylene diisocyanate (1,6‐diisocyanatohexane) and isophorone diisocyanate (5‐isocyanate1‐isocyanatomethyl‐1,3,3‐trimetylcyclohexane) were used as functionalizing agents. This article reports on the effects that the various central elastomeric PAC blocks (type, content, and molecular weight) had on the polymerization kinetics and on the structure and molecular weights of the multiblock copolymers obtained. The copolymers were characterized spectroscopically. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 487–496, 2003     

SYNTHESIS AND CHARACTERIZATION OF POLY(STYRENE - ETHYLENE OXIDE) DIBLOCK COPOLYMERS

1NTRODUCTIONSinceanionicpolymerizationhasthecharactersofnon--terminationandnon--chainstransferinallpolymersynthesisreactions,themolecularweightandmolecularweitghtdistributionofpolymerscanbecontrolledbyiteasily,soastopreparethepolymerswithexpectedfinestructures.Especially,theattentionisfocusedonthediblockcopolymersmanufacturedbythecomonomerswithdifferent.h....t.r.["ZJ,whichcancompatibilizethetwoincompatiblepolymersascompatibilizer['].InthesystemsofgelorlatexthediblockcOPolymerscanimprovet…     

Using Triethylborane to Manipulate Reactivity Ratios in Epoxide-Anhydride Copolymerization: Application to the Synthesis of Polyethers with Degradable Ester Functions

The anionic ring-opening copolymerization (ROCOP) of epoxides, namely of ethylene oxide (EO), with anhydrides (AH) generally produces strictly alternating copolymers. With triethylborane (TEB)-assisted ROCOP of EO with AH, statistical copolymers of high molar mass including ether and ester units could be obtained. In the presence of TEB, the reactivity ratio of EO (r_EO), which is normally equal to 0 in its absence, could be progressively raised to values lower than 1 or higher than 1. Conditions were even found to obtain r_EO equal or close to 1. Samples of P(EO-co-ester) with minimal compositional drift could be synthesized; upon basic degradation of their ester linkages, these samples afforded poly(ethylene oxide) (PEO) diol samples of narrow molar mass distribution. In other cases where r_EO were lower or higher than 1, the PEO diol samples eventually isolated after degradation exhibited a broader distribution of molar masses because of the compositional drift of initial P(EO-co-ester) samples.     

Double hydrophilic block copolymers of sodium(2‐sulfamate‐3‐carboxylate)isoprene and ethylene oxide

Poly(sodium(2‐sulfamate‐3‐carboxylate)isoprene)‐b‐poly(ethylene oxide) and poly(ethylene oxide)‐b‐poly(sodium(2‐sulfamate‐1‐carboxylate)isoprene)‐b‐poly(ethylene oxide) double hydrophilic block copolymers were prepared by selective post polymerization reaction of the polyisoprene block, of poly(isoprene‐b‐ethylene oxide) diblocks or poly(ethylene oxide‐b‐isoprene‐b‐ethylene oxide) triblock precursors, with N‐chlorosulfonyl isocyanate. The precursors were synthesized by anionic polymerization high vacuum techniques and had narrow molecular weight distributions and predictable molecular weights and compositions. The resulting double hydrophilic block copolymers were characterized by FTIR and potentiometric titrations in terms of the incorporated functional groups. Their properties in aqueous solutions were studied by viscometry and dynamic light scattering. The latter techniques revealed a complex dilute solution behavior of the novel block copolymers, resulting from the polyelectrolyte character of the functionalized PI block and showing a dependence on solution ionic strength and pH. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 606–613, 2006     

Synthesis of NMP/RAFT inifers and preparation of block copolymers

Two different initiator/transfer agents (inifers) containing an alkoxyamine and a dithiobenzoate were synthetized and used to trigger out either reversible addition‐fragmentation chain transfer (RAFT) polymerization or nitroxide‐mediated polymerization (NMP). α‐Dithiobenzoate‐ω‐alkoxyamine‐difunctional polymers were produced in both cases which were subsequently used as precursors in the formation of block copolymers. This synthetic approach was applied to N‐isopropylacrylamide (NIPAM) or polyethylene oxide methacrylate (EOMA) to form α,ω‐heterodifunctional homopolymers via RAFT at 60°C which were chain extended with styrene by activating the alkoxyamine moiety at 120°C. Under such temperature conditions, it is proposed that a tandem NMP/RAFT polymerization is initiated producing a simultaneous growth of polystyrene blocks at both chain‐ends. Self‐assembled nanostructures of these amphiphilic block copolymers were evidenced by scanning electron microscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012