分子模拟方法考察泡沫生成能力

采用分子模拟的方法研究表面活性剂的泡沫生成能力, 以界面形成能作为考察泡沫体系中液膜界面积的量化依据, 研究了泡沫液膜厚度、表面活性剂分子界面密度以及表面活性剂类型对泡沫液膜界面形成能计算的影响. 通过与实验结果相对应, 建立了界面形成能和泡沫生成能力之间的联系.     

Gemini表面活性剂对疏水缔合聚丙烯酰胺界面吸附膜扩张流变性质的影响

采用小幅低频振荡和界面张力弛豫技术, 考察了疏水缔合水溶性聚丙烯酰胺(HMPAM)在正癸烷-水界面上的扩张黏弹性质, 研究了不对称Gemini表面活性剂C₁₂COONa-p-C₉SO₃Na对其界面扩张性质的影响. 研究发现, 疏水链段的存在, 使HMPAM在界面层中具有较快的弛豫过程, 扩张弹性显示出明显的频率依赖性. 表面活性剂分子可以通过疏水相互作用与聚合物的疏水嵌段在界面上形成类似于混合胶束的特殊聚集体. 表面活性剂分子与界面聚集体之间存在快速交换过程, 可以大大降低聚合物的扩张弹性. 同时, 聚合物分子链能够削弱表面活性剂分子长烷基链之间的强相互作用, 导致混合吸附膜的扩张弹性远低于单独表面活性剂吸附膜.     

气相二氧化硅/季铵Gemini表面活性剂稳定的泡沫体系

以zeta电位法研究了季铵Gemini表面活性剂亚甲基-α, ω-双(十二烷基二甲基溴化铵) (12-s-12, s=2, 6)在水溶液中修饰气相二氧化硅(F-SiO₂)粒子。这些粒子随表面活性剂浓度C增加经历了表面从原先的亲水到疏水再重新亲水的改变,其中疏水粒子可以自发吸附在气泡液膜中,从而很好地稳定泡沫。重新亲水的粒子脱附出液膜,仅留下表面活性剂稳定气泡。强的液膜弹性对应于稳定的泡沫。联接链长度影响了Gemini在F-SiO₂粒子表面的吸附,因而也影响了液膜的弹性和对泡沫的稳定。超短s=2联接链的12-2-12由于反离子解离不完全而带有较少的正电荷,在粒子表面的初始吸附弱于12-6-12,但因此减少了吸附分子头基间的静电排斥,可以形成更致密的吸附层。由于12-2-12本身比12-6-12具有更强的界面吸附能力,F-SiO₂粒子和12-2-12的协同作用可以更好地稳定泡沫体系。     

十二烷基苯磺酸钠在SiO2表面聚集的分子动力学模拟

采用分子动力学方法研究了阴离子表面活性剂十二烷基苯磺酸钠(SDBS)在无定形SiO2固体表面的吸附. 设置不同的水层厚度, 观察固液界面和气液界面吸附的差异. 模拟发现表面活性剂分子能够在短时间内吸附到SiO2表面, 受碳链和固体表面之间相互作用的影响形成表面活性剂分子层, 并依据吸附量的大小形成不同的聚集结构; 在水层足够厚的情况下, 由于有较多的表面活性剂分子吸附在固体表面,从而形成带有疏水核心的半胶束结构; 计算得到的成对势表明极性头与钠离子或水分子之间的结合或解离与二者之间的能垒有关, 解离能垒远大于结合能垒, 引起更多Na+聚集在极性头周围而只有少数Na+存在于溶液中; 无论气液还是固液界面, 极性头均伸向水相, 与水分子形成不同类型的氢键. 模拟表明, 分子动力学方法可以作为实验的一种补充, 为实验提供必要的微观结构信息.     

十二烷基苯磺酸钠在SiO2表面聚集的分子动力学模拟

采用分子动力学方法研究了阴离子表面活性剂十二烷基苯磺酸钠(SDBS)在无定形SiO2固体表面的吸附.设置不同的水层厚度,观察同液界面和气液界面吸附的差异.模拟发现表面活性剂分子能够在短时间内吸附到SiO2表面,受碳链和固体表面之间相互作用的影响形成表面活性剂分子层,并依据吸附量的大小形成不同的聚集结构;在水层足够厚的情况下,由于有较多的表面活性剂分子吸附在固体表面,从而形成带有疏水核心的半胶束结构;计算得到的成对势表明极性头与钠离子或水分子之间的结合或解离与二者之间的能垒有关,解离能垒远大于结合能垒,引起更多Na+聚集在极性头周围而只有少数Na+存在于溶液中;无论气液还是固液界面,极性头均伸向水相,与水分子形成不同类型的氢键.模拟表明,分子动力学方法可以作为实验的一种补充,为实验提供必要的微观结构信息.     

表面活性剂对驱油聚合物界面剪切流变性质的影响

利用双锥法研究了表面活性剂十二烷基苯磺酸钠(SDBS)和十六烷基三甲基溴化铵(CTAB)对油田现场用部分水解聚丙烯酰胺(PHPAM)和疏水改性聚丙烯酰胺(HMPAM)溶液的界面剪切流变性质的影响,实验结果表明:HMPAM分子通过疏水作用形成界面网络结构,界面剪切复合模量明显高于PHPAM.SDBS和CTAB通过疏水相互作用与HMPAM分子中的疏水嵌段形成聚集体,破坏界面网络结构,剪切模量随表面活性剂浓度增大明显降低.同时,界面膜从粘性膜向弹性膜转变.低SDBS浓度时,少量SDBS分子与PHPAM形成混合吸附膜,界面膜强度略有升高;SDBS浓度较高时,界面层中PHPAM分子被顶替,吸附膜强度开始减弱.阳离子表面活性剂CTAB通过静电相互作用中和PHPAM分子的负电性,造成聚合物链的部分卷曲,从而降低界面膜强度.弛豫实验结果证实了表面活性剂破坏HMPAM网络结构的机理.     

Gemini表面活性剂乙烷基-α,ω-双十四烷基二甲基溴化铵产生的高稳定泡沫

报道了由gemini表面活性剂乙烷基-α,ω-双十四烷基二甲基溴化铵(14-2-14)产生的高稳定泡沫体系.泡沫塌陷到初始高度一半所对应的时间(t1/2)用来表征泡沫的稳定性.测得14-2-14体系的t1/2高达961min,远大于乙烷基-α,ω-双十二烷基二甲基溴化铵(12-2-12)产生泡沫的t1/2(754min),表明带有一根短联接链和两条长尾链的gemini表面活性剂是高效的泡沫稳定剂.为了揭示界面弹性与泡沫稳定性之间的关联,测量了表面活性剂吸附膜的扩张流变行为.在指定的表面过剩量下,吸附膜的高频极限弹性再一次被发现与泡沫稳定性相关,较大的极限弹性很好地对应更加稳定的泡沫.     

扩张流变法研究表面活性剂在界面上的聚集行为

近年发展起来的界面流变测定技术在研究界面性质方面具有许多独特之处.本文结合我们的工作,总结了近年来有关该技术在表面活性剂界面聚集行为研究中的应用,讨论了扩张频率、表面活性剂浓度及疏水链长、无机盐和温度对表面扩张流变行为的影响,同时探讨了小分子表面活性剂与高分子表面活性剂表面扩张流变行为的区别以及小分子表面活性剂在气/液界面与液/液表面的扩张流变性的差异.大量研究表明,借助于界面流变性的测定不仅可以研究发生在界面上和界面附近的微观弛豫过程,而且可以探讨界面上超分子聚集体的形成,进而为乳状液和泡沫等分散体系的稳定性提供依据.     

层状液晶凝胶对微泡沫的稳定作用

以非离子表面活性剂单硬脂酸甘油酯(GMS)制备出稳定的微泡沫. 采用偏光显微镜、冷冻断裂蚀刻透射电子显微镜(FF-TEM)、差示扫描量热仪(DSC)和流变仪对其表面活性剂溶液相态、泡沫体系的微观结构、相变行为和流变性进行研究以探索微泡沫的稳定机理. 实验结果表明, 表面活性剂分子吸附在气泡界面, 发生晶化形成有序、紧密排列的层状液晶凝胶相液膜, 该液膜具有较强的刚性, 能抵抗由Laplace附加压力驱使的气泡溶解和聚并行为. 微泡沫可稳定10个月, 无明显的相分离和气泡破裂现象. 其稳定作用机理是通过影响泡沫排液过程, 增强Gibbs-Marangoni效应, 从而提高了气泡液膜强度, 减缓了气相扩散速率.     

气液界面上阴离子表面活性剂单层膜的分子动力学模拟

用分子动力学方法研究了阴离子表面活性剂十二烷基硫酸钠(SDS)在气液界面上的结构和动力学性质. 选择单分子占有面积分别为0.45和0.68 nm²的两个模拟体系, 通过径向分布函数表征了单层膜的厚度, 并根据疏水链中碳原子与极性头中硫原子之间组成的矢量分布和取向函数, 对比了不同界面单层膜的有序排列情况. 结果表明在分子占有面积较小达到饱和吸附的情况下, 界面上的SDS具有较好的有序性. 通过计算气液界面附近水分子的扩散系数发现: 由于氢键和静电作用的影响, 界面区域内的水分子较本体溶液中的水分子有较弱的迁移能力.     

Effect of alkyl chain length on the surface dilational rheological and foam properties of N-acyltaurate amphiphiles

The dynamic dilational properties of sodium 2-(2-(alkylaryloxy)-alkylamido)ethanesulfonates (12+nB-Ts) at the air–water interfaces were investigated by drop shape analysis, and their foam properties were also measured. The influences of time and bulk concentration on surface dilational properties were expounded. The results show that the molecular interaction controls the nature of adsorption film during lower concentration range, and the film behaves elastic in nature. During higher concentration range, the diffusion exchange process controls the dynamic dilational properties and the surface film shows remarkable viscoelasticity. An increase in hydrophobic chain length enhances the molecular interaction at low concentration and speeds up the diffusion exchange process at high concentration, which results in the different variations of modulus at different concentration regions. For 12+nB-Ts, too short a chain probably produces bad film elasticity, whereas too great a length produces too fast liquid drainage. Therefore the optimal length in the branched chain leads to the best foam stability.     

Synergistic improvement of foam stability with SiO2 nanoparticles (SiO2-NPs) and different surfactants

Foam fluids are widely used in petroleum engineering, but long-standing foam stability problems have limited the effectiveness of their use. The study explores the synergistic effects and influencing factors of SiO₂ nanoparticles (SiO₂-NPs) with different wettability properties and three different surfactants. The paper investigates the foaming performance of different types of surfactants and analyzes and compares the stability of foam after adding hydrophilic and hydrophobic SiO₂-NPs from macroscopic as well as microscopic perspectives, and the effects of temperature and inorganic salts on the stability of mixed solutions. The experimental results show that: 1) hydrophilic nanoparticles can significantly enhance the foam stability of amphoteric surfactants, with a small increase in the foam stability of anionic and cationic surfactants; 2) The concentration of nanoparticles did not have a significant effect on the stability of the cationic surfactants and this conclusion was verified in the experimental results of the surface tension measured below;3) The cationic surfactants showed better temperature resistance at temperatures of 50–90 °C. Both amphoteric surfactant solutions with the addition of hydrophilic SiO₂-NPs or hydrophobic SiO₂-NPs significantly improved the temperature resistance of the foam at high temperatures. The anionic surfactant solution with hydrophobic SiO₂-NPs did not enhance the solution temperature resistance; 4) The surface tension of the surfactant solution gradually increases with increasing concentration of hydrophilic or hydrophobic SiO₂-NPs and then levels off; 5) the hydrophilic SiO₂-NPs had a significant effect on the salt tolerance of the anionic and amphoteric surfactant solutions. The salt tolerance of cationic surfactant solutions with hydrophobic SiO₂-NPs was better than that of surfactants with hydrophilic SiO₂-NPs.     

起泡剂/稳泡剂/SiO2复合泡沫缓速酸液体系协同增效性能

为了有效控制液相中H⁺向岩石表面的扩散,降低酸-岩反应速率,进而达到深度酸化刻蚀的目的,通过对纳米颗粒、稳泡剂与表面活性剂协同增效作用的研究,制备了一种泡沫稳定、耐温性能及缓速性能优异的泡沫缓速酸。室内通过对比不同纳米材料在酸液中的分散性能及纳米颗粒粒径对泡沫缓速酸性能的影响,优选出d=25 nm的亲水型Si O₂纳米材料。采用自制的两性表面活性剂(MAC)作为起泡剂,并加入自制的酸液稠化剂(SY-1)作为稳泡剂以达到稳泡作用。当w(Si O₂)=1.5%、w(MAC)=1.0%、w(SY-1)=0.08%时,所形成的泡沫也更加致密,液膜厚度增强,泡沫稳定性提高,半衰期延长,从7 min增长到69 min;并且SY-1的加入提高了泡沫的耐高温性能,使体系在90℃时半衰期仍然能达到29 min。通过测定不同条件下酸岩反应速率并进行比较,结果表明,20%HCl基液的平均酸岩反应速率为1.148×10^-3 mg/(cm²·s),而实验室自制泡沫缓速酸液体系的平均酸-岩反应速率降至7....     

Effect of organic acid chain length on foam performance in a porous medium

We have systematically studied the effect of organic acid chain length on surface dilatational properties and foam flow performance in a porous medium. Surface dilatational properties were studied by oscillating drop module (ODM). ODM results in deionized water show that sufficient long chain length of organic acid is an essential requirement for high surface dilatational modulus. While, to various salinities, surfactant to acid ratio of achieving high surface dilatational modulus varies. Foam flow tests show that surface dilatational modulus has decisive effect on produced foam size, which partially determines foam flow pressure drop. Both surface dilatational modulus and surface tension determine foam flow pressure drop. Besides, surface loss modulus also contributes to pressure drop. Bulk foam tests show that addition of organic acids with proper chain length can enhance foam tolerance to oil significantly. Compared with alkane chain length, acid with longer chain has good ability in stabilizing foam. At last, foam flooding tests show that surface dilatational modulus and foam tolerance to oil play important roles in foam enhanced oil recovery.     

芳基油酸酰胺羟丙基磺基甜菜碱的合成及性能

合成了3种具有不同疏水基团的新型磺基甜菜碱两性表面活性剂,通过红外光谱对它们的结构进行了表征。 用滴体积法测定表面活性剂水溶液在25 ℃下的表面张力,从而确定其临界胶束浓度(cmc)及临界胶束浓度下的表面张力(γcmc);采用罗氏泡沫仪考察了浓度、温度对其泡沫性能的影响;采用分水时间法考察了其乳化性能。 结果表明,随着芳环在烷基链中的体积增大,cmc以及γcmc增大,饱和吸附面积Amin增大,而饱和吸附量Γmax减小。 3种表面活性剂的起泡性随浓度增大而增加,到一定值后趋于稳定;泡沫稳定性随浓度增大逐渐增强;起泡性随着温度的升高而显著增加,泡沫稳定性随温度升高而显著降低。 3种表面活性剂的乳化能力随浓度增大而逐渐增强然后趋于稳定。     

A Surface Rheological Study of Polyoxyethylene Alkyl Ether Carboxylic Salts and the Stability of Corresponding Foam

The dynamic dilational viscoelastic properties of polyoxyethylene alkyl ether carboxylic salts at the air-water interface were investigated by drop shape analysis method and their foam stability were measured by Bikerman Method. The influences of time, dilational frequency, and bulk concentration on surface dilational modulus and phase angle were expounded. The results show that the surfactant with the longest straight-chain shows the highest dilational modulus, which in agreement with the best foam stability. However, the foam stability of branched-alkyl chain surfactant cannot be explained in terms of film elasticity alone.     

Critical capillary pressure for destruction of single foam films and foam: effect of foam film size

Foams and single foam films stabilised by ionic and amphiphile polymer surfactants are studied with foam pressure drop technique (FPDT) and thin liquid film-pressure balance technique (TLF-PBT). A pressure is reached at which the single foam films rupture and the foams destruct very fast (avalanche-like). For film rupture we named this pressure—critical capillary pressure of film rupture, P_cr,film while for foam destruction, we introduced a new parameter—critical capillary pressure of foam destruction, P_cr,foam. The surfactant kind and foam film type (common thin, common black and Newton black) affect the values of both parameters. When below 20 kPa, P_cr,film and P_cr,foam are close by value, when over 20 kPa, there is a significant difference between them. The P_cr,film versus film size and P_cr,foam versus foam dispersity dependences, indicate that the film size and foam dispersity strongly affects the critical capillary pressure values. Film size distribution histograms reveal that a foam always contains films that are of a larger than the most probable size. They rupture at lower pressures, does initiating the destruction of the whole foam, which can be an explanation why higher than 20 kPa there is a difference between P_cr,film and P_cr,foam values. This parameter, P_cr,foam is considered of significant with respect to foam stability and could find use in industry.     

Influence of Foam Apparent Viscosity and Viscoelasticity of Liquid Films on Foam Stability

The objective of this research work was to study the relationship among the apparent viscosity of bulk foam, the viscoelasticity of liquid films, and foam stability. Bulk foam tests showed that the drainage half-life of AOS foam was higher than that of sodium dodecyl sulfate (SDS) and hexadecyltrimethyl ammonium bromide (CTAB) foams. The results of foam apparent viscosity revealed that the foam apparent viscosity was related to foam quality rather than foam stability. Higher film viscoelasticity modulus could be assigned for α -olefin sulfonate (AOS) films than those for SDS and CTAB ones. The film conductivity tests indicated that AOS liquid films, compared with SDS and CTAB liquid films, could delay the liquid drainage speed under dynamic conditions. Compared with foam apparent viscosity, the viscoelasticity of liquid films appeared to be a key factor in foam stability.     

Foams and foam films stabilized by CnTAB: influence of the chain length and of impurities

Quantitative comparison of foam films and the corresponding foams is very demanding. One problem is the fact that investigations of foam films are usually performed at constant capillary pressures P, whereas in foams P is a function of the height of the foam column. A way out of this dilemma is to examine films and foams at the same P. The method of choice for the foam films is the thin film pressure balance (TFPB), whereas the corresponding investigation of foams is based on the foam pressure drop technique (FPDT). An extensive TFPB study on foam films stabilized by the cationic alkyltrimethylammonium bromides C(n)TAB with n=10, 12, 14, and 16 was performed by Bergeron. For this series a steep increase of the foam film stability was observed when the chain length was increased from n=12 to n=14. Moreover, the influence of impurities was found to be limited to the films stabilized by C(12)TAB. In order to study the correlation between the properties of films and foams, the present study deals with the respective foam properties investigated with the FPDT. It was found that both the steep increase in the film stability and the influence of impurities are also reflected in the properties of the foam.     

聚醚型表面活性剂在界面上的分子取向Ⅰ. Triton X-100和Triton X-305在水面上的展开膜

研究了25 ℃时Triton X-100和Triton X-305在46.6％NaNO_3水溶液/空气界面上的展开膜。根据表面压、分子面积和分子中乙氧基数目三者之间的关系, 提出了一种界面分子模型。简言之, 分子的烷烃链伸进气相或油相, 分子中间的苯环平躺于界面, 而分子的乙氧基链则以一部分链节平躺于界面、其余的链节伸进水相的方式取向。平躺于界面的乙氧基链节的比例随表面压的增加而减小。这个模型不仅可以合理地解释已知的实验事实, 而且可能适用于包括空气/水和油/水界面上的展开膜和吸附膜。