Preparation and characterization of gradient distribution of silicon in emulsion blend films

In this work, a functional gradient polymeric material derived from silicon-containing acrylate blend emulsion film is prepared in two steps. Firstly, 3-[tris(trimethylsilyloxy)silyl] propyl methacrylate (TRIS)-modified acrylate latex is prepared using multiple emulsifiers by the two-stage semicontinuous emulsion copolymerization method. Next, blend latexes composed of TRIS-containing and TRIS-free acrylate latexes are obtained. Detailed studies on the effects of the film-formation temperature and the glass transition temperature (T _g) differences on the compositional gradient film are conducted. Surface energy analysis shows that silicon elements enriched at the film-air (F-A) interface and T _g differences facilitate the fabrication of silicon gradient in emulsion blend films. Scanning electron microscopy-energy dispersive X-ray further reveals that the concentration of silicon components varies in a gradient-like manner along the overall transaction of the film when the film-formation temperature is 55 °C. However, excessive temperature creates the formation of a segmental gradient distribution of silicon in the emulsion blend films.     

Synthesis of poly(vinylidene chloride)-based composite latexes by emulsion polymerization from epoxy functional seeds for improved thermal stability

Poly(glycidyl methacrylate-co-butyl methacrylate)/poly(vinylidene chloride-co-methyl acrylate) (poly(GMA-co-BMA)/poly(VDC-co-MA)) composite latexes have been successfully synthesized via a two-stage emulsion polymerization process. In a first step, emulsion copolymerization of GMA and BMA was carried out in optimized conditions (low temperature, neutral pH, starved-feed conditions) to both limit the hydrolysis of epoxy groups and obtain small particle size (typically 30-50 nm size range). Composite latexes were then obtained by a second-stage seeded copolymerization of VDC and MA in the presence of tetrasodium pyrophosphate to control the pH and reach high molecular weight, leading to partial encapsulation of the seed particles (snow-man morphology, in agreement with theoretical expectations). Thermogravimetric analyses performed on the resulting composite particles showed that the epoxy-functionalized seed polymer behaved as an efficient thermal stabilizer of PVDC.     

Application of FTIR Microscopy in Combinatorial Experimentation on Polymer Blends

Summary: A novel combinatorial, high-throughput experimentation (HTE) setup has been developed, which allows for rapid mapping of the phase behavior of blends of homopolymers and block copolymers. The principle is based on the preparation of composition (ϕ)-temperature (T) gradient films. Linear ϕ gradients were obtained over a large composition range, as shown by FTIR microscopy. The applicability of this combinatorial approach was demonstrated by studying the phase behavior of a poly(styrene-co-acrylonitrile) (SAN)/poly(methyl methacrylate-co-ethyl acrylate) (PMMA-EA) blend with varying EA content and a poly(styrene-b-butadiene-b-methyl methacrylate) (SBM) triblock copolymer.     

Preparation and surface properties of latexes with fluorine enriched in the shell by silicon monomer crosslinking

A series of core-shell acrylic copolymer latexes containing fluorine enriched in the shell have been prepared by emulsion polymerization of a variety of hydrocarbon monomers with (perfluoroalkyl)methyl methacrylate and vinyltriethoxysilicone. In the presence of a reactive anionic and a long chain anionic-nonionic emulsifier, the core-shell latexes were prepared and characterized by transmission electron microscopy (TEM) and tapping-mode atomic force microscopy (AFM). From AFM and contact angle measurements, it was observed that the resulting fluorine and silicon-containing acrylic copolymers with surface energy as low as 15.5 mN/m formed a dense and gradient film containing a surface layer with high a fluorine content, and that the fluorinated particles can be fixed on the surface due to the crosslinking reaction of multi-functional silicon monomer even though the fluorinated carbon number was not enough to crystallize.     

Synthesis and characterization of a novel macromolecular surface modifier for polyethylene

A new macromolecular surface modifier, a copolymer of lauryl methacrylate (LMA) and poly(ethylene glycol) methyl methacrylate (PEGMA), was synthesized through free radical polymerization. The copolymer was characterized by nuclear magnetic resonance spectrum (1H-NMR) and thermogravimetric analysis (TGA). The copolymer was used to blend with polyethylene. The binary blends have been characterized by attenuated total reflection/Fourier transform infrared (ATR-FTIR), contact-angle measurements (CDA) and scanning electron microscopy (SEM). The results indicated that poly(ethylene glycol) methyl methacrylate-co-lauryl methacrylate (PEGMA-co-LMA) could diffuse preferably onto the surface of the polyethylene (PE) film, and thus can be used as an efficient surface modifier for PE.     

Surface structures and properties of polystyrene/poly(methyl methacrylate) blends and copolymers

Sum frequency generation (SFG) vibrational spectroscopy has been applied to study the molecular surface structures of polystyrene (PS)/poly(methyl methacrylate) (PMMA) blends and the copolymer between PS and PMMA (PS-co-PMMA) in air, supplemented by atomic force microscopy (AFM) and contact angle goniometer. Both the blend and the copolymer have equal weight amounts of the two components. SFG results show that both components, PS and PMMA, can segregate to the surface of the blend and the copolymer before annealing, although PMMA has a slightly higher surface tension. Upon annealing both SFG results and contact angle measurements indicate that the PS segregates to the surface of the PS/PMMA blend more but no change occurs on the PS-co-PMMA surface. AFM images show that the copolymer surface is flat but the 1:1 PS/PMMA blend has a rougher surface with island like domains present. The annealing effect on the blend surface morphology has also been investigated. We collected amide SFG signals from interfacial fibrinogen molecules at the copolymer or blend/protein solution interfaces as a function of time. Different time-dependent SFG signal changes have been observed, showing that different surfaces of the blend and the copolymer mediate fibrinogen adsorption behavior differently.     

Modification of hydrophilic poly(vinyl alcohol) film via blending with hydrophobic poly(butyl acrylate-co-methyl methacrylate)

A series of poly(vinyl alcohol)/poly(butyl acrylate-co-methyl methacrylate) [PVA/P(BA-co-MMA)] blend films with different P(BA-co-MMA) content were prepared by the solution casting method. Surface morphologies of the PVA/P(BA-co-MMA) blend films were studied by scanning electron microscopy and atomic force microscopy. Thermal, mechanical, and chemical properties of PVA/P(BA-co-MMA) blend films were investigated by differential scanning calorimeter, thermogravimetric analysis, tensile tests, and surface contact angle tests. It was revealed that the introduction of P(BA-co-MMA) could affect the properties of the PVA films. The results also showed that, when P(BA-co-MMA) mole content is 3 %, the tensile strength and the surface contact angle of the polymer blend film are 20.4 MPa and 43.5°, respectively, suggesting that the polymer blend film holds both a better mechanical property and a better chemical property.     

Preparation and evaluation of poly(alkyl methacrylate-co-methacrylic acid-co-ethylene dimethacrylate) monolithic columns for separating polar small molecules by capillary liquid chromatography

In this study, methacrylic acid (MAA) was incorporated with alkyl methacrylates to increase the hydrophilicity of the synthesized ethylene dimethacrylate-based (EDMA-based) monoliths for separating polar small molecules by capillary LC analysis. Different alkyl methacrylate–MAA ratios were investigated to prepare a series of 30% alkyl methacrylate–MAA–EDMA monoliths in fused-silica capillaries (250-μm i.d.). The porosity, permeability, and column efficiency of the synthesized MAA-incorporated monolithic columns were characterized. A mixture of phenol derivatives is employed to evaluate the applicability of using the prepared monolithic columns for separating small molecules. Fast separation of six phenol derivatives was achieved in 5 min with gradient elution using the selected poly(lauryl methacrylate-co-MAA-co-EDMA) monolithic column. In addition, the effect of acetonitrile content in mobile phase on retention factor and plate height as well as the plate height-flow velocity curves were also investigated to further examine the performance of the selected poly(lauryl methacrylate-co-MAA-co-EDMA) monolithic column. Moreover, the applicability of prepared polymer-based monolithic column for potential food safety applications was also demonstrated by analyzing five aflatoxins and three phenicol antibiotics using the selected poly(lauryl methacrylate-co-MAA-co-EDMA) monolithic column.     

Miscibility of poly(vinyl chloride) with poly(methyl-co-hexyl acrylate) and poly(methyl-co-2 ethyl hexyl acrylate)

The miscibility and phase behavior in blends of PVC with poly(methyl-co-hexyl acrylate)[MHA] and poly(methyl-co-2 ethyl hexyl acrylate)[MEH] were studied. It was found that PVC is miscible with MHA copolymers having a HA volume fraction from 0.30 to 0.92 and MEH copolymers having an EH volume fraction from 0.30 to 0.83 at 100°C. By applying the mean field theory to the phase diagrams of these blend systems, segmental interaction parameters which represent the binary interaction between different monomer units were estimated. The calculated values reflect the fact that the miscibility window observed for PVC/MHA and PVC/MEH blend systems was attributed to the effect of repulsion between different monomer units within the copolymer. To investigate the effect of specific interaction on the miscibility for these blend systems, an attempt was also made to describe the blend interaction parameter as a function of polar group concentration in the acrylate copolymer. The blend interaction parameter values exhibit a u-shaped curve as a function of the weight fraction of C?O group in the copolymer, and the lowest blend interaction parameter value appears at about 0.24 C?O weight fraction.     

Nanostructured latex films from poly(butyl methacrylate) latex cross-linked with poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) triblock macro-cross-linker

Biphasic polymer latexes were synthesized by a seeded swelling and polymerization method. The latexes were composed of a poly(butyl methacrylate) core and a poly(ethylene oxide) rich shell cross-linked with poly(ethylene oxide)-poly (propylene oxide)-poly(ethylene oxide) triblock diol diacrylate macro-cross-linker. Nanostructured films were obtained by annealing the biphasic polymer latexes at a temperature between the glass-transition temperatures of the core latex and the cross-linked poly(ethylene oxide) based shell. Atomic force microscope images of the latex film revealed that the poly(butyl methacrylate) core phase is confined in the poly(ethylene oxide)-rich continuous phase with the form of separate nanosized spheres.     

Microstructure of poly(methyl methacrylate-co-isopropyl acrylate) studied by 13C NMR

The distribution of configurational–compositional sequences of poly(methyl methacrylate-co-isopropyl acrylate) (PMMA/iPrA) has been determined from the carbonyl and β-CH₂ signals in the 100?MHz ¹³C NMR spectra of the copolymer. The carbonyl signal provided information on configurational–compositional sequences up to heptads, whereas β-CH₂ signals offered complementary information on even sequences up to hexads. The assignment of the sequences to the respective signals was based on a comparison with the spectra of respective homopolymers, that is, PMMA and PiPrA followed by a computer simulation applying an incremental calculation of chemical shifts of the individual sequences.     

Polystyrene(1)/poly(butyl acrylate-methacrylic acid)(2) core-shell emulsion polymers. Part II: Thermomechanical properties of latex films

Polystyrene(1)/poly(n-butyl acrylate-methacrylic acid)(2) structured latex particles were prepared through a two-stage emulsion polymerization procedure, using a polystyrene (PS) latex seed (118 nm), and differentn-butyl acrylate (BA)/methacrylic acid (MAA) ratios. Polymerization kinetics, particle morphology, and MAA location have already been discussed in the first part of this series. In this second part the thermomechanical behavior of films cast from these latexes was studied. Differential Thermal Analysis and Dynamic Mechanical Analysis (DMA) were employed as characterization techniques for the films. Two polymer phases corresponding to polystyrene and a poly(BA-MAA) copolymer were distinguished. Comparison was made to analogous unfunctionalized PS/PBA systems, as a result of which an effect of MAA upon the phase arrangement in the film was found. Scanning Electron Microscopy of film samples and DMA showed that the evolution of the phase arrangement as a result of annealing was strongly dependent on the type of mechanical and heat treatments being applied to functionalized systems. Finally, the thermomechanical behavior of films was related to the structural features of the corresponding latexes, and computer simulation techniques wer eemployed to establish a mechanistic support for these relationships.     

含氟/硅丙烯酸酯核壳型乳液的合成及性能

采用半连续种子乳液聚合法, 在十二烷基硫酸钠(SDS)/辛基苯基聚氧乙烯醚(TX-10)复合乳化剂的作用下, 合成了以丙烯酸丁酯(BA)为核, 以甲基丙烯酸甲酯(MMA)、甲基丙烯酸十二氟庚酯(DFHMA)、3-(甲基丙烯酰氧)丙基三甲氧基硅烷(MPTMS)和甲基三甲氧基硅烷(MTMS)为壳的核壳型含氟/硅丙烯酸酯聚合物乳液. 利用FTIR, TEM, SEM-EDX和DSC等手段对乳液组成、乳胶粒子结构、膜表面及断面形态等进行了表征, 讨论了氟/硅含量对聚合物膜性能的影响. 结果表明, 核-壳粒子尺寸为20~30 nm, 乳液膜的性能与膜表面氟和硅的含量及相容性有较大的相关性, 当m(氟)∶m(硅单体)=3∶1时, 形成的膜均匀透明, 吸水率较低, 尺寸稳定性较好.     

氟含量对含氟丙烯酸酯共混乳胶膜梯度结构和表面性能的影响

首先将制备出的平均粒径较小的含氟丙烯酸酯均聚物乳液与平均粒径较大的纯丙烯酸酯共聚物乳液按不同的比例( 1/9,2/8,3/7,4/6,5/5)共混,接着将各共混乳液在室温下(20℃)玻璃基材上干燥后,于110℃/210℃下热处理一段时间.运用接触角法,XPS、AFM、SEM-EDX等详细研究了共混乳胶膜中含氟组分含量对...     

Controlled synthesis of poly(acetone oxime acrylate) as a new reactive polymer: Stimuli-responsive reactive copolymers

Acetone oxime acrylate has been synthesized as a new active ester monomer. Free radical polymerization yielded a reactive polymer soluble in various organic solvents, such as chloroform, dioxane, DMSO, acetone, methanol, dichloromethane, DMF, and ethanol. Controlled radical polymerization of acetone oxime acrylate was successfully conducted using the RAFT, NMP and Iniferter method. Partly polymer analogous reaction with N-isopropylamine resulted in the reactive copolymer poly(N-isopropylacrylamide-co-acetone oxime acrylate), which featured a lower critical solution temperature (LCST) of 61 °C in water. Further, the reactivity of the copolymer was exemplary proven by complete reaction with ammonia yielding poly(N-isopropylacrylamide-co-acrylamide), which does not possess a LCST.     

Water-induced (nano) organization in poly(ethyl acrylate-co-hydroxyethyl acrylate) networks

The conformational changes in poly(ethyl acrylate-co-hydroxyethyl acrylate), P(EA-co-HEA) chains, which constitute a copolymer network hydrogel, induced by the presence of water are investigated by different experimental techniques and compared with the behaviour of the corresponding xerogel. The mechanical relaxation spectrum shows the presence of a new water-induced relaxation, the water content dependence of the glass transition is measured by DSC, and the dielectric relaxation assesses the effect of water for the lower concentrations. Hydrophilic and hydrophobic monomeric units in the P(EA-co-HEA) network are able to aggregate to form two separated (nano)phases in the presence of water due to hydrophobic interaction. Phase separation takes place when the water content of the sample is higher than a critical value estimated as two water molecules per -OH group in the copolymer chain. The existence of the hydrophobic domains is detected by their glass transition being nearly independent on the water content of the sample. Phase separation is also clearly revealed by phase angle measurements in AFM experiments.     

Poly(ethylene-co-vinyl alcohol) and poly(methyl methacrylate) blends: Phase behavior and morphology

In this work blends of poly(ethylene-co-vinyl alcohol) (EVOH) with different ethylene contents (27, 32, 38 and 44 mol%) and poly(methyl methacrylate) (PMMA) were prepared by mechanical mixing in the melted state. The miscibility and melting behavior as a function of blend composition and the ethylene content in EVOH copolymers were investigated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The morphology of the cryofractured surfaces was examined by scanning electron microscopy (SEM). DSC and DMTA data show that EVOH/PMMA blends are immiscible, independent of EVOH and blend composition. The SEM analysis in agreement with DMTA analysis indicates that the morphology of phases depends on the blend composition, with phase inversion occurring as the concentration of one or other polymer component increases. However, the copolymer composition apparently does not affect the domain size distribution for blends containing 20 wt% of EVOH or 20 wt% of PMMA. A better phase adhesion is observed mainly for blends with 50 wt% of each polymer component.     

Surface self-segregation, wettability, and adsorption behavior of core-shell and pentablock fluorosilicone acrylate copolymers

The surfaces of films cast from core-shell fluorosilicone acrylate copolymer (BA/MMA/DFHM and BA/MMA/DFHM/MPTMS/D(4)) latexes and linear pentablock fluorosilicone acrylate copolymer (PDMS-b-(PMMA-b-PDFHM)(2)) solutions are intensively investigated and compared by XPS, DCA, AFM, and QCM-D measurements. It is found that the molecular structures and in-solution aggregate structures of these well-defined copolymers have a dramatic influence on the surface structure formation, surface wetting, and adsorption behavior. The PDMS-b-(PMMA-b-PDFHM)(2) film cast from chloroform solution with high concentration of low-density unimers is able to perform as strong surface self-segregation of fluorine-containing groups as core-shell copolymer latex films. The BA/MMA/DFHM/MPTMS/D(4) in the core-shell latex particles exhibits the less pronounced surface self-segregation of silicon-containing groups than PDMS-b-(PMMA-b-PDFHM)(2) due to the occurrence of cross-linking reactions between polysiloxane chains. Indeed, such reactions induce the formation of silica network within the film material, which immobilizes tightly the fluorinated groups on the film surface and thus endows the film with higher surface structural stability for water compared to PDMS-b-(PMMA-b-PDFHM)(2) film with similar surface fluorine concentration and even higher silicon concentration. Still, the PDMS-b-(PMMA-b-PDFHM)(2) film definitely demonstrates higher advancing and receding contact angles for water than BA/MMA/DFHM/MPTMS/D(4) latex film in the case of synergism between surface enrichment of fluorine and silicon.     

Quantifying phase behavior in partially miscible polystyrene/poly(styrene‐co‐4‐bromostyrene) blends

The phase behavior of thin‐film blends of polystyrene (PS) and the random copolymer poly(styrene‐co‐4‐bromostyrene) (PBS) was studied with atomic force microscopy (AFM) and small‐angle X‐ray scattering (SAXS). Phase behavior was studied as a function of the PBS and PS degree of polymerization (N), degree of miscibility [controlled via the volume fraction of bromine in the copolymer (f)], and annealing conditions. The Flory–Huggins interaction parameter χ was measured directly from SAXS as a function of temperature and scaled with f as χ = f²χ_S–BrS [where χ_S–BrS represents the segmental interaction between PS and the homopolymer poly(4‐bromostyrene)] Simulations based on the Flory–Huggins theory and χ measured from SAXS were used to predict phase diagrams for all the systems studied. The PBS/PS system exhibited upper critical solution temperature behavior. The AFM studies showed that increasing f in PBS led to progressively different morphologies, from flat topography (i.e., one phase) to interconnected structures or islands. In the two‐phase region, the morphology was a strong function of N (due to changes in mobility). A comparison of the estimated PBS volume fractions from the AFM images with the PBS bulk volume fraction in the blend suggested the encapsulation of PBS in PS, supporting the work of previous researchers. Excellent agreement between the phase diagram predictions (based on χ measured by SAXS) and the AFM images was observed. These studies were also consistent with interdiffusion measurements of PBS/PS interfaces (with Rutherford backscattering spectroscopy), which indicated that the interdiffusion coefficient decreased with increasing χ in the one‐phase region and dropped to zero deep inside the two‐phase region. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 255–271, 2002     

Upper critical solution temperature type phase behavior of poly(styrene‐co‐acrylonitrile) blends with poly(styrene‐co‐n‐phenyl maleimide) and their interaction energies

To enhance the heat resistance of poly(styrene‐co‐acrylonitrile‐co‐butadiene), ABS, miscibility of poly(styrene‐co‐acrylonitrile), SAN, with poly(styrene‐co‐n‐phenyl maleimide), SNPMI, having a higher glass transition temperature than SAN was explored. SAN/SNPMI blends casted from solvent were immiscible regardless of copolymer compositions. However, SNPMI copolymer forms homogeneous mixtures with SAN copolymer within specific ranges of copolymer composition upon heating caused by upper critical solution temperature, UCST, type phase behavior. Since immiscibility of solvent casting samples can be driven by solvent effects even though SAN/SNPMI blends are miscible, UCST‐type phase behavior was confirmed by exploring phase reversibility. When copolymer composition of SNPMI was fixed, the phase homogenization temperature of SAN/SNPMI blends was increased as AN content in SAN copolymer increased. To understand the observed phase behavior of SAN/SNPMI blend, interaction energies of blends were calculated from the UCST‐type phase boundaries by using the lattice‐fluid theory combined with a binary interaction model. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1131–1139, 2008