A high‐stability Eu complex has been achieved by coating with a silica glass via a low temperature sol–gel process using deuterated methanol. A three‐dimensional glass network protects the Eu complex from free oxygen and/or water to change the ligand structure. In addition, the chemical bond of the deuterated Eu complex is more stable than that of the conventional Eu complex. Therefore, we achieved a high‐thermal‐stability Eu complex encapsulated by a sol–gel derived silica glass using deuterated methanol instead of ethanol.
Steady‐state and time‐resolved photoluminescence of silicon nanoparticles dispersed in low‐polar liquids at above room temperature is studied. The roles of low‐polar liquids as well as mechanisms responsible for their temperature‐dependent photoluminescence are discussed. The thermal sensitivity of the photoluminescence is estimated and application of the nanoparticles as nanothermometers is proposed.
We report on solution‐processible polymer solar cells (PSCs) fabricated on a papery substrate using carton. Highly conductive PEDOT:PSS was used as a bottom anode and planarization layer, and a semi‐transparent top cathode was applied. This research could be an important approach to the development of all‐solution‐processible papery PSCs as well as paper electronics.
The growth, structural and optical characterisation of dilute nitride alloys of InSb grown by plasma‐assisted molecular beam epitaxy is presented. The layers were characterised by high‐resolution X‐ray diffraction indicating high crystalline quality and nitrogen incorporations up to 0.68%. Fourier‐transform infrared absorption measurements reveal the position of the absorption edge to be a result of the competing effects of bandgap reduction (due to nitrogen incorporation and bandgap renormalisation) and Moss–Burstein band filling.
We demonstrated important changes produced on the modulation frequency of hybrid organic–inorganic light‐emitting diodes to examine the applicability as a light source for visible optical communications. The fabricated device structure was 4,4′‐bis[N ‐(1‐napthyl)‐N ‐phenyl‐amino]biphenyl/4,4′‐(bis(9‐ethyl‐3‐carbazovinylene)‐1,1′‐biphenyl:4,4′‐bis[9‐dicarbazolyl]‐2,2′‐biphenyl/ZnS/LiF/MgAg. This device showed an improvement in the modulation frequency using ZnS instead of an organic material, tris(8‐hydroxyquinoline)aluminum. A maximum cutoff frequency of 20.6 MHz was achieved.
The metastability of the bixbyite‐ and corundum‐type In2O3 polymorphs up to 33 GPa (at room temperature) is shown. While compressed (in diamond anvil cells) and laser‐heated, both polymorphs undergo a phase transition to the Rh2O3‐II‐type structure (space group Pbcn, No. 60). The direct transition from bixbyite to Rh2O3‐II structure has not yet been observed for any other oxide.
We demonstrate the monolithic integration of a microstructured organic photodiode with a planar optical stripe waveguide. The manufacturing of this waveguide‐integrated organic photodiode is based on an UV photolithography process. The integration of photodiodes with optical waveguides represents an essential building block in the field of optoelectronic‐photonic integrated circuits.
Write‐once–read‐many‐times memory (WORM) devices were fabricated using Ti/Au and Au as top contacts on ZnO thin films on Si. Electrical characterization shows that both types of WORM devices have large resistance OFF/ON ratio (R ratio), small resistance distribution range, long retention and good endurance. WORM devices with Au top contact have better performance of higher R ratio because of a larger work function of Au compared to Ti.
Nanostructures formed in a titanium dioxide (TiO2)–poly(styrene)‐block‐poly(ethyleneoxide) nanocomposite film on top of fluor‐doped tin oxide (FTO) layers are investigated. The combinatorial approach is based on probing a wedge‐shaped FTO‐gradient with grazing incidence small angle X‐ray scattering (GISAXS) in combination with a moderate micro‐focus X‐ray beam. The characteristic lateral length is given by adjacent nanowire‐shaped TiO2 regions. It decreases from 200 nm on the thick FTO layer to 90 nm on the bare glass surface.
We report the fabrication procedure and the characterization of an Al0.3Ga0.7As solar cell containing high‐density GaAs strain‐free quantum dots grown by droplet epitaxy. The production of photocurrent when two sub‐bandgap energy photons are absorbed simultaneously is demonstrated. The high quality of the quantum dot/barrier pair, allowed by the high quality of nanostructured strain‐free materials, opens new opportunities for quantum dot based solar cells.
Interaction between negatively charged Nafion® and a positively charged polybenzimidazole‐decorated carbon nanotube leads to the formation of an ionic complex with high charge density for proton conduction, which can lead to an improvement in transport properties. Here we investigate the high‐temperature and low‐humidity proton conductivity of this nanocomposite membrane as a potential membrane for fuel cell applications.
A facile metal catalyst free route to synthesize boron doped (0.6%–1.0%) carbon nanotubes via ceramic nanowires in which the formation of the nanowires (probably serving as templates), the carbon nanotubes and their doping all occur unanimously in the reaction, is presented.
The current–voltage characteristics and photoresponse of mesa structured {111}‐oriented homoepitaxial CVD diamond p(i)n‐junctions with different intrinsic layer thickness are investigated. When a sufficiently thick intrinsic layer is present, a rectification ratio of 108 at ±10 V could be obtained. Good rectifying diodes show a high photoresponse ratio between 210 nm (above bandgap) and 500 nm (below bandgap), making them suitable for UV detection purposes. The results are compared with similar measurements carried out on polycrystalline CVD diamond pn‐junctions.
By means of first‐principles calculations we predict the stability of silicene as buckled honeycomb lattice on passivated substrates of group‐IV(111)1 × 1 surfaces. The weak van‐der‐Waals interaction between silicene and substrates does not destroy its linear bands forming Dirac cones at the Brillouin zone corners. Only very small fundamental gaps are opened around the Fermi level.
A new method for fabricating carbon nanotube‐conducting polymer (CNT‐CP) composite single nanowires is reported. The method developed is highly efficient, reliable, and economical because it obviates the time consuming process of template fabrication and the post‐synthesis task of positioning nanowires. Single nanowires with diameters of 50‐500 nm are fabricated between electrodes, self‐templated by dielectrophoresis and electropolymerization. Fabrication of an individually addressed nanowire array with cantilever electrodes on a microchip is demonstrated.
