Extraction-chromatographic preconcentration with chromatomembrane separation of extract from aqueous phase for luminescence determination of oil products and phenols in natural water by flow injection analysis

The new method of preconcentration by extraction for flow injection analysis (FIA) with luminescence and photometric detection is proposed. Preconcentration is carried out on extraction-chromatographic column, extract is eluted by extragent with the following separation of extract from aqueous phase in chromatomembrane cell. Possibilities of the proposed method are illustrated in the examples of FIA with luminescence determination of oil products and phenols in natural water.     

Flow-injection flame atomic absorption spectrometric determination of trace amounts of cadmium in solid and semisolid milk products coupling a continuous ultrasound-assisted extraction system with the online preconcentration on a chelating aminomethylphosphoric acid resin

A new sensitive and low-cost method that combines continuous acid extraction, online preconcentration, and flame atomic absorption spectrometry for cadmium determination at microg levels in solid and semisolid milk products is described. A continuous ultrasound-assisted extraction system is used to carry out the dynamic acid extraction step. The acid extract is preconcentrated online on a minicolumn packed with a chelating resin (Chelite P, with aminomethylphosphoric acid groups), and the retained cadmium is eluted with hydrochloric acid and continuously monitored by flame atomic absorption spectrometry. An experimental design (Plackett-Burman 2-6*3/16) is used to optimize the continuous extraction and the preconcentration step. The method allowed a total sampling frequency of 28 samples/h. A good precision of the whole procedure (3.0% relative standard deviation) for a cheese sample containing 0.103 +/- 0.004 microg/g Cd (dry mass), a high enrichment factor (20.5), and detection and quantification limits of 0.014 and 0.067 microg/g, respectively, for a 60 mg of sample were obtained with this methodology. The method was successfully applied to the determination of trace amounts of cadmium in solid and semisolid milk products, such as cheese and yogurt samples.     

Continuous ultrasound-assisted extraction of hexavalent chromium from soil with or without on-line preconcentration prior to photometric monitoring

A continuous ultrasound-assisted extractor was coupled to a photometric detector in order to obtain a fully automated approach for the determination of CrVI in soil. The use of a flow injection (FI) manifold as interface between the extractor and the photometric detector allowed the monitoring of CrVI after extraction in a continuous manner. The coloured complex formed between 1,5-diphenylcarbazide (DPC) and CrVI was used as recommended in EPA method 7196A because it is one of the most sensitive and selective reactions for CrVI determination. A preconcentration minicolumn packed with a strong anion-exchange resin was placed between the extractor and the detector, providing a more sensitive method. The linear dynamic ranges were 1-10 and 0.25-7.5 mg l-1 for the methods without (method A) and with preconcentration (method B), respectively. The limits of detection were 4.52 ng for method A and 1.23 ng for method B. Both methods were applied to a natural contaminated soil and the results obtained agreed well with those obtained by the reference EPA method 3060A. The influence of different amounts of CrIII in the samples was also studied and the results showed that the proposed methods did not disturb the original species distribution.     

Solid-Phase Extractive Preconcentration of Trace Copper as its Calmagite Anionic Chelate using a Polyaniline Column for Flame Atomic Absorption Spectrometric Determination

A new solid phase extraction method based on the application of polyaniline as the sorbent and calmagite as the anionic chelating agent is reported for selective preconcentration of trace copper, prior to its determination by microsample injection system-flame atomic absorption spectrometry. The parameters that influence the extraction and chelate formation were optimized. The copper was retained on a polyaniline minicolumn at pH 4.0 and eluted with 2.0 mL of 3.0 mol L^?1 nitric acid. Under the optimum conditions, the limit of detection, the relative standard deviation, and the preconcentration factor were 1.98 µg L^?1, less than 5.4%, and 50 to 200, respectively. The method was validated through the analysis of certified reference water samples and standard addition measurements. Quantitative recoveries between 93.4% and 103.5% were obtained. The method was successfully applied to the determination of copper in water.     

Determination of lead and mercury in sea water by preconcentration in a flow injection system followed by atomic absorption spectrometry detection

The capabilities of three solid chelating reagents were compared for the preconcentration of lead and mercury in high salinity aqueous samples (sea waters). The tested materials were 7-(4-ethyl-1-methyloctyl)-8-hydroxiquinoline (Kelex 100) adsorbed on Bondapack C18 (Kelex-100/C18), 8-hydroxiquinoline immobilized on vinyl co-polymer Toyopearl gel (TSK) and the commercial polystyrene/DVB ion exchange resin with paired iminodiacetate groups (Chelex-100). The two metals preconcentration and final determination were carried out in a flow injection system, coupled on-line to an atomic absorption spectrometric detector. Analytes were preconcentrated in the minicolumn, packed with the materials under investigation, while elution was achieved by injection of 500 μl of an adequate mineral acid solution. The different packing materials and minicolumn designs have been evaluated in terms of sensitivity for simultaneous preconcentration of both metals in sea water. Regarding the solid support, the best results were obtained for the TSK solid phase. Concerning the minicolumn design, the behavior was different for lead and mercury. Lead was quantitatively eluted with 0.5 M HCl and best performance was achieved when packing the solid material in a minicolumn with relatively small volume (1 cm length and 2.5 mm i.d.). In the case of mercury, bigger minicolumn volumes (5.5 cm length and 5.0 mm i.d.) and mixtures, 2 M HCl+1 M HNO₃, were required for its quantitative recovery and elution. The system has been evaluated for quantitative determination of the two metals under study in different Asturian coastal aqueous samples.     

Coupling Pervaporation-Gas Chromatography for Speciation of Volatile Forms of Selenium in Sediments

Abstract

A method for speciation of dimethylselenide (DMeSe), dimethyldiselenide (DMeDSe) and diethylselenide (DEtSe) in sediments based on a coupling between a pervaporation module, a preconcentration sorptive trap and a gas chromatograph-mass spectrometer is reported. The coupling is performed through a high pressure injection valve which allows two different operational modes: (a) analysis without preconcentration, in which analytes are directly driven from the pervaporation chamber to the injection port of the chromatograph, and (b) analysis with preconcentration in a trap, in which the analytes from the pervaporation chamber are first trapped on a Tenax minicolumn and then thermally desorbed and driven to the GC. This second approach improves the sensitivity compared to the direct coupling, reaching estimated absolute detection limits lower than 0.6 ng Se for each tested species. The method is applied to the determination of volatile organic selenium species in several sediments collected from different areas in the Southwest of Spain.     

Evaluation of an on-line coupled continuous flow liquid membrane extraction and precolumn system as trace enrichment technique by liquid chromatographic determination of bisphenol A

An on-line coupled continuous flow liquid membrane extraction (CFLME) and C₁₈ precolumn system was developed for sample preconcentration in liquid chromatography determination. After preconcentration by CFLME, which is based on the combination of continuous flow liquid–liquid extraction and supported liquid membrane, bisphenol A (BPA) was enriched in 960 μl of 1 mol l⁻¹ NaOH used as acceptor. This acceptor was on-line neutralized and transported onto the C₁₈ precolumn where analytes were absorbed and focused. Then the focused analytes were injected onto a C₁₈ analytical column for separation and detected at 220 nm with a diode array detector. CFLME related parameters such as flow rates, pH of donor and acceptor, and enrichment time were optimized. The proposed method presents a detection limit of 0.03 μg l⁻¹ (S/N=3) when 60 ml samples was enriched with an enrichment time of 30 min. Compared with C₁₈ based column-switching procedure, this proposed procedure presents similar sample throughput and lower detection limits. The proposed method was successfully applied to determine BPA in tap water, river water, and municipal sewage effluent samples.     

Continuous approach for ultrasound-assisted acid extraction-minicolumn preconcentration of chromium and cobalt from seafood samples prior to flame atomic absorption spectrometry.

A rapid and sensitive method has been proposed for the determination of chromium and cobalt in seafood samples by flame atomic absorption spectrometry combined with a dynamic ultrasound-assisted acid extraction and an on-line minicolumn preconcentration. The use of diluted nitric acid as extractant in a continuous mode at a flow rate of 3.5 mL min(-1) and room temperature was sufficient for quantitative extraction of these trace metals from seafoods. A minicolumn containing a chelating resin was an excellent device for the quantitative preconcentration of chromium and cobalt prior to their detection. A flow-injection manifold was used as interface for coupling all analytical steps, which allowed the automation of the whole analytical process. A Plackett-Burman experimental design was used as a multivariate strategy for the optimization of both sample preparation and preconcentration steps. The method was successfully applied to the determination of chromium and cobalt in seafood samples.     

Development of a new sequential injection in-line cloud point extraction system for flame atomic absorption spectrometric determination of manganese in food samples

A preconcentration method for manganese determination by sequential injection cloud point extraction with subsequent detection by flame atomic absorption spectrometry (FAAS) has been developed. The enrichment of Mn was performed after a preliminary on-line cloud point extraction and entrapment of manganese-containing surfactant aggregated within a minicolumn packed with cotton. The laboratory-made reagent 4-(5′-bromo-2′-thiazolylazo)orcinol (Br-TAO) and the surfactant Triton X-114 were used for cloud point extraction. The manganese ions were eluted with sulphuric acid solution and directly introduced into the FAAS. Chemical and flow variables affecting the preconcentration were studied. Using a sample volume of 2.80 mL the limit of detection and enrichment factor were calculated to be 0.5 μg L⁻¹ and 14, respectively. The sample frequency is 48 h⁻¹, considering a total run cycle of 75 s. The accuracy of the proposed method has been demonstrated by the analysis of the certified reference biological materials rice flour and tomato leaves. The method has been applied to determination of manganese in food samples.     

Simultaneous determination of trans-resveratrol and sorbic acid in wine by capillary zone electrophoresis

A method for separation and determination of sorbic acid, a food and beverage preservative, and trans-resveratrol, a biomedically active substance, in wine by capillary zone electrophoresis is described. A solid-phase extraction step on C18-column prior to the electrophoretic separation providing lower detection limits was used for trans-resveratrol determination. For determination of sorbic acid direct analysis of wine (without a preconcentration step) was used. The method is rapid and sensitive and was applied to the analysis of wines from Alsace, France.     

Coupling continuous subcritical water extraction,filtration, preconcentration,chromatographic separation and UV detection for the determination of chlorophenoxy acid herbicides in soils

Subcritical water extraction has been coupled with filtration, preconcentration and chromatographic analysis for the determination of acid herbicides in different types of soil. Two experimental designs were used for the optimization of the leaching step. The use of water as extractant in the continuous mode at a flow-rate of 1 ml/min and 85 degrees C was sufficient for quantitative extraction of the analytes. A static extraction time was unnecessary for reducing the extraction time to 1 h. A minicolumn containing C18-Hydra as sorbent proved an excellent material for the quantitative preconcentration of the herbicides prior to individual chromatographic separation. A flow-injection manifold was used as interface for coupling the four steps, thus allowing automation of the whole analytical process. Recoveries of the target analytes ranged between 94.2 and 113.1%, and repeatabilities, expressed as relative standard deviations, were between 0.61 and 6.83%.     

A continuous approach for the determination of Cr(VI) in sediment and soil based on the coupling of microwave-assisted water extraction, preconcentration, derivatization and photometric detection

A dynamic system for the continuous leaching of Cr(VI) from sediment and soil based on both microwave assistance and iterative change of the flow direction of the extractant through the sample cell has been developed. The microwave-assisted extractor has been coupled to a photometric detector through a flow injection interface in order to develop a fully automated method. The Cr(VI) extracted was monitored after derivatization with 1,5-diphenylcarbazide. Two approaches are proposed which differ in the inclusion of a preconcentration minicolumn packed with a strong anion exchange resin. A 0.04 M ammonium buffer solution was used as extractant and 0.2 g of sample—river sediment spiked with 50 and 5 μg g⁻¹ for the method without preconcentration (method A) and with preconcentration (method B)—was subjected to 8-14 min of 300 W microwave-assisted extraction. The within-laboratory reproducibility and repeatability were 2.6 and 1.9 for method A, and 4.0 and 2.6 for method B. The proposed methods have been compared with the reference EPA method 3060/7196.     

Simultaneous determination of gold and copper by reversed-phase high-performance liquid chromatography using online column enrichment as their syn-phenyl-2-pyridylketoximate chelates.

Gold and copper ions react with syn-phenyl-2-pyridylketoxime (PPKO) at 40 degrees C to form neutral chelates. Metal-PPKO chelates subsequently become preconcentrated on a minicolumn packed with a divinylbenzene-methacrylate copolymer. By switching the valve, these chelates are separated on the silica-based phenyl column and detected with a photometric detector. These processes occur automatically except for chelation. The results of the chelation, preconcentration, and separation conditions studies are presented. Calibration curves for Au and Cu ions are linear from nanograms per milliliter (parts per billion) to micrograms per milliliter (parts per million) in the original solution. The precision for 0.5-ppm standards of Au and Cu is 2.1 and 0.9 relative standard deviation (%), respectively. The accuracy of the present method is verified for Au and Cu based on the analysis of a standard alloy of the National Institute of Standards and Technology (NIST). The limits of detection for Au and Cu are 16.7 and 0.6 ppb, respectively. The effects of foreign ions on the determination of Au and Cu are discussed.     

Flow-through fluorescence-based optosensor with on-line solid-phase separation for the simultaneous determination of a ternary pesticide mixture

A rapid and selective method was developed for the simultaneous determination of 3 widely used pesticides, carbendazim (CBZ), carbofuran (CF), and benomyl (BNM). The method utilized a single continuous-flow, solid surface fluorometric multioptosensor implemented with a previous separation of the analytes on a minicolumn, placed just before the sensor, that was packed with the same solid support (C18 silica gel) as the flow-through cell. The separation was achieved because of the different kinetics of retention/elution of the pesticides on the solid support in the minicolumn, enabling the sequential arrival of the analytes at the sensing zone. With a single injection of the mixture, 2 of them were more strongly retained in the minicolumn (CF and BNM) while the other (CBZ) passed through the system towards the sensing material where it developed its fluorescence transitory signal. Then, CF and BNM were successively eluted from the solid support using 2 different eluting solutions, and they sequentially reached the sensing zone and developed their respective signals. A multiwavelength fluorescence detection mode was used, recording the signals of each pesticide at its maximum excitation/emission wavelength; therefore, the sensitivity was increased. The system was calibrated using a sample volume of 2000 microL. The linear dynamic range was 80-1400, 250-2400, and 150-2000 ng/mL with detection limits of 15, 68, and 35 ng/mL and relative standard deviation values of 3.5, 3.2, and 2.4% for CBZ, CF, and BNM, respectively. A recovery study was applied to spiked environmental water samples, and recoveries ranged from 96 to 104%.     

固相萃取-离子色谱法测定地下水中痕量高氯酸根离子

建立了测定地下水中痕量高氯酸根（ClO~4）的固相萃取-离子色谱(SPE-IC)分析方法。0.7 L水样经预处理降低主要干扰离子Cl~、CO2~3和SO2~4的干扰后,使用Cleanert PWAX弱阴离子交换固相萃取小柱对地下水中痕量(μg/L级)的ClO~4进行富集,用6 mL 1%NaOH溶液洗脱,富集液经0.45 μm水膜过滤后,用IonPac AS20阴离子分离柱、50 μL进样环、40 mmol/L KOH溶液淋洗、抑制电导检测分离分析。结果表明,地下水样品中ClO~4的方法检出限和测定下限分别为0.15 μg/L和0.60 μg/L,进样质量浓度在1～15 μg/L范围内有很好的线性关系,线性相关系数为0.9992,回收率为99.7%～100.5%;该方法经济有效,可用于地下水中痕量ClO~4的检测。利用该方法测定了哈尔滨周边部分地区地下水中ClO~4浓度,检测结果与离子色谱-质谱联用法的检测结果的相对误差为1.85%～9.24%。     

Lead preconcentration onto C-18 minicolumn in continuous flow and its determination in biological and vegetable samples by flame atomic absorption spectrometry

A procedure for the preconcentration and determination of lead in vegetable and biological samples was developed in the continuous mode coupled to a flame atomic absorption spectrometer. Lead is quantitatively preconcentrated in acetic buffer as its diethyldithiocarbamate chelate onto a C-18 minicolumn, placed in the loop of a proportional injector, eluted by a stream of methyl isobutyl ketone and introduced directly into the nebuliser. A detection limit of 3 microg 1(-1) is obtained using a time-based technique for 2 min preconcentration and an RSD of 3.8% was readily achieved for three measurements of 25 microg Pb 1(-1). The sample throughput is 24 h(-1). Using preconcentration times of 10 min an enrichment factor of 189 can be obtained. The continuous flow system was used for some reference sample analysis and the obtained results reveal that the methodology can be easily applied for vegetable and biological sample analysis.     

Field preconcentration of cadmium from seawater by using a minicolumn packed with Amberlite XAD-4/4-(2-pyridylazo) resorcinol and its flow-injection-flame atomic absorption spectrometric determination at the ng L(-1) Level

A flow injection analysis-flame atomic absorption spectrometric method for the determination of cadmium in seawater was developed with the aim of yielding a sensitive assay with a low detection limit. The method employs a field flow preconcentration technique involving a minicolumn containing Amberlite XAD-4 impregnated with the complexing agent 4-(2-pyridylazo) resorcinol. A Plackett-Burman 2(7)x3/32 design for seven factors (sample pH, sample flow rate, eluent volume, eluent concentration, eluent flow rate, ethanol percentage in the eluent and minicolumn diameter) was carried out in order to find the significant variables affecting the field continuous preconcentration system (FCPS) and the flow injection elution manifold for cadmium determination in seawater samples by flame atomic absorption spectrometry. Cadmium can be preconcentrated with an enrichment factor of 1053 for a sample volume of 200 mL and a preconcentration time of 57 min. In these experimental conditions, the method provides a linear relationship between absorbance and cadmium concentration in the range from 22-1900 ng L(-1), with a detection limit (3SD) of 6 ng L(-1). The precision (expressed as relative standard deviation) for eleven independent determinations reached values of 8.9-0.8% in cadmium solutions of 50-700 ng L(-1). Analysis of certified reference materials (SLEW-3 and NASS-5) showed good agreement with the certified value. This procedure was applied to the determination of cadmium in seawater from Galicia (Spain).     

Determination of metal ions by ion chromatography with precolumn electrochemical preconcentration

The determination of heavy metals in concentrations less than 10(-6) mol/L by ion chromatography with conductivity detection requires a preconcentration step. Therefore, a special electrochemical equipment and method was developed for the on-line preconcentration of the divalent metals Ni, Co, Zn and Cd and their subsequent ion chromatographic determination. The loop of the injection valve of an ion chromatograph was replaced by an electrochemical flow-through-cell with a gold working electrode, a platinum auxiliary electrode and a silver/silver sulphate reference electrode. The preconcentration step consists of the deposition of the reduced metals on the electrode surface during a continuous pumping of the sample solution through the cell. After switching of the mobile phase through the cell, the analytes are injected after their reoxidation directly into the mobile phase. A new preconcentration step is simultaneously possible during the actual chromatographic run. An effective separation of the analytes from the matrix is also possible with the proposed system. A maximum of metal ion accumulation was obtained after 120 min in the galvanostatic mode on a gold tube electrode. The detection limits for Co(II), Ni(II), Zn(II) and Cd(II) were improved by a factor of 7.7, 10.4, 11.2, 14.0, respectively, and were in the 0.1 micromol/L concentration range with a RSD of 2-6%. The accumulation of metal ions was disturbed in the presence of Cr(III).     

Preconcentration of cobalt with 8-hydroxyquinoline and gas chromatographic stationary phase Chromosorb 105 and its determination by graphite furnace atomic absorption spectrometry

This paper presents a study of the adsorption characteristics of a commercially available GC stationary phase Chromosorb 105 for Co²⁺, which can be successfully applied to the preconcentration of Co²⁺ in water samples followed by GFAAS determination. After reacting with 8-hydroxyquinoline to form a complex at pH 8.0, Co²⁺ in water can be retained on a minicolumn packed with Chromosorb 105 and eluted with 2.5 ml of a mixture of ethanol and 2 mol l⁻¹ HNO₃ (2+1, v/v). The recoveries of Co²⁺ from 200 ml of tap water, river water and bottled natural mineral water samples are quantitative. Conditions for quantitative and reproducible preconcentration, elution and subsequent GFAAS determination were studied. A highly sensitive, simple method for preconcentration and GFAAS determination of trace amount of cobalt in natural water samples using a Chromosorb 105 packed minicolumn has been proposed. The high retention efficiency (95%) for Co²⁺ provides a sensitivity enhancement of 80 for a 200 ml sample volume with a detection limit of 13.4 ng l⁻¹ (3σ) and a quantification limit of 44.5 ng l⁻¹ (10σ).     

Automated on-line-solid-phase extraction—high-performance liquid chromatography-diode array detection of phenolic compounds in sherry wine

A new analytical method has been developed for sample preconcentration and analysis of phenolic compounds in sherry wine using on-line solid-phase extraction(SPE)-HPLC-diode array detection. The samples of wine were injected and adsorbed onto polystyrene divinylbenzene cartridges; a robotic semiflexible system was used to automate the SPE stage. Chromatographic separation was carried out in a Symmetry C₁₈ steel cartridge, with a two-step elution gradient. Peaks were identified by comparing their UV spectra with the library of spectra compiled by the authors.