丝素蛋白-聚氨酯复合水凝胶的制备及性能研究

以聚乙二醇(PEG)、聚氧化丙烯二醇(PPG)、异弗尔酮二异氰酸酯(IPDI)为主要原料制备聚氨酯预聚体(PU),与丝素蛋白水溶液(SF)交联制得丝素蛋白-聚氨酯(SF-PU)复合水凝胶.分别利用ATR、SEM对水凝胶组成、结构及微观形貌进行表征;DSC、吸水溶胀测试探讨了丝素蛋白与聚氨酯的质量比(SF/PU)以及聚氨酯中不同软段质量比(PEG/PPG)对SF-PU水凝胶热性能、溶胀性能的影响.结果表明,SF-PU水凝胶具有多孔结构;样品中不同的SF/PU、PEG/PPG均对材料的玻璃化转变温度、结晶度及溶胀性能产生影响,且当水凝胶组分为SF/PU=1/25、PEG/PPG=2/1时,平衡溶胀比(ESR)可达到440%;水凝胶在溶胀初始阶段符合菲克扩散模型,整个溶胀过程遵循溶胀动力学2级方程.     

温度和pH敏感P(NIPA-co-AA)/粘土复合水凝胶的辐射制备与表征

以N-异丙基丙烯酰胺(NIPA)作为温敏性聚合单体,丙烯酸(AA)为pH敏感性单体,有机粘土为改性剂,采用~(60)Co-γ射线为辐射源,辐射合成了P(NIPA-co-AA),粘土复合水凝胶,研究了粘土的加入对水凝胶溶胀率、温度及pH敏感性和压缩性能的影响.结果表明,P(NIPA-co-AA)/粘土复合水凝胶的溶胀性能优于P(NIPA-co-AA)水凝胶,平衡溶胀率(SR)明显提高;且复合水凝胶仍表现出明显的温度和pH敏感性;粘土的加入提高了水凝胶的压缩强度、最大压缩力和压缩屈服力等力学性能,当粘土含量为15%时,P(NIPA-co-AA)/粘土复合水凝胶的压缩强度为P(NIPA-co-AA)共聚水凝胶的2.4倍,最大压缩力为P(NIPA-co-AA)的2.1倍.     

双重交联VSNPs-PAA纳米复合水凝胶的制备及其溶胀性能的研究

采用自由基聚合法合成了乙烯基硅纳米粒子-聚丙烯酸(VSNPs-PAA)双重交联复合水凝胶,考察了交联剂、引发剂、单体以及p H值、温度、盐溶液等对水凝胶溶胀行为的影响。结果表明,引发剂浓度为0.08%,交联剂浓度为0.1%,单体浓度为80%时,合成的水凝胶溶胀性能最大,吸水率达到5000%以上;该水凝胶不仅具有p H值敏感性和p H值变化下良好的反复性,而且在p H4的酸性溶液中表现出温度敏感性,其溶胀率随温度的升高而增大;水凝胶的溶胀率随着盐溶液浓度的增大而减小。     

壳聚糖-聚丙烯酸复合水凝胶的药物控制释放行为

以壳聚糖(Cs)和丙烯酸(AA)为原料,利用自由基聚合法制备了具有孔洞结构的复合水凝胶Cs-PAA,并研究了AA的量、交联剂的量、聚合温度和AA的中和度对水凝胶溶胀度的影响以及复合水凝胶对烟酸的控制释放。 结果表明,Cs-PAA复合水凝胶具有良好的pH值、离子强度敏感性,且溶胀度最高达1228 g/g,其在pH=686的缓冲溶液中的烟酸累积释放率明显大于其在pH=1.80的缓冲溶液,因此Cs-PAA水凝胶可作为肠口服药物的载体。     

基于Pickering乳液的磁性高强水凝胶的制备及性能表征

合成了一种磁性Fe3O4纳米颗粒稳定的水包油(O/W)Pickering乳液并以其作为交联剂,在适宜条件下引发单体丙烯酰胺聚合来制备了一种新型的磁性高强复合水凝胶.采用X射线衍射(XRD)及场发射扫描电子显微镜(SEM)分别对磁性Fe3O4纳米颗粒和复合水凝胶的结构进行了表征,结果表明Pickering乳胶粒子较均匀地分布在复合凝胶网络中.溶胀性能测试及溶胀动力学分析表明复合水凝胶具有良好的溶胀性能,能够吸收自身干重100倍左右的水,其溶胀过程不遵循Fickian扩散模型;拉伸测试表明该水凝胶具有优异的力学性能,其拉伸强度能够达到150 kPa左右,断裂伸长率能够达到300%左右,并且当其承受的应力释放后能快速地恢复到初始形态.磁性能测试的结果显示该水凝胶具有良好的磁性.     

大豆分离蛋白/琼脂糖复合水凝胶

采用简单的物理共混方法,制备一种大豆分离蛋白/琼脂糖降温型复合水凝胶.即在高温下聚乙二醇改性的大豆分离蛋白/琼脂糖混合物呈溶液状态,降温至生理温度37℃或更低温度则形成水凝胶.表征了该复合凝胶的溶胀度、力学性能、细胞毒性和细胞迁移率.结果表明,改性大豆分离蛋白/琼脂糖复合水凝胶具有较高的溶胀度和力学性能,良好的生物相容性和细胞迁移率,在伤口敷料领域显示出潜在的应用.     

聚乙烯醇/纳米羟基磷灰石/丝素蛋白复合水凝胶的制备及其性能研究

本文以聚乙烯醇(PVA)、纳米羟基磷灰石(n-HA)和丝素蛋白(SF)为原料,采用物理共混法、反复冷冻解冻法和NaCl粒子制孔法制得了具有三维结构的PVA/n-HA/SF多孔复合水凝胶,以作为人工角膜支架材料。测试了这种多孔复合材料的含水率、拉伸强度和断裂伸长率,并对其进行了红外谱图、X射线衍射光谱、热重及电子扫描显微镜分析。结果表明,丝素蛋白的添加量增加时,多孔复合水凝胶的含水率相应提高,含水率稳定在75～82%之间;其拉伸强度在0.43～1.00MPa之间,断裂伸长率在183.76～237.53%之间,可以达到人体正常状态下眼压要求,其中复合水凝胶的最佳配比为:PVA:SF:n-HA=10:5:1。;IR和XRD分析表明复合水凝胶在物理交联过程中,各种成分均匀复合,无化学键变化;扫描电镜显示该水凝胶材料具有均匀的三维多孔结构。     

黏土基纳米复合水凝胶

介绍了一种以黏土为交联剂的新型纳米复合水凝胶, 重点阐述了水凝胶的结构特点, 制备方法及其特有的力学性能, 自修复性能, 透明度和溶胀性。     

基于壳聚糖/聚丙烯酸/纳米银的高强抗菌水凝胶

首先以丙烯酸(AA)和壳聚糖(CS)为单体、N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,通过光聚合法制备了CS/PAA双网络水凝胶,然后将Ag~+以硝酸银的形式分散在水凝胶中并通过紫外光辐照获得CS/PAA/纳米银复合水凝胶,并对复合水凝胶的抗菌性能进行研究。采用红外光谱对其结构进行表征,研究单体含量对水凝胶力学性能以及溶胀行为的影响。结果表明,当丙烯酸质量分数为20%,壳聚糖质量分数为5%的情况下,水凝胶的拉伸性能最优。此外,纳米银的引入有效提高了水凝胶的抗菌性能。     

聚N-异丙基丙烯酰胺/纳米SiO2复合水凝胶的合成及溶胀性能

通过纳米SiO2的表面功能化,在其表面引入乙烯基功能基团,在H2O／THF的混合溶剂中,超声分散后,交联剂N,N′-亚甲基双丙烯酰胺存在时,于25℃下使其与N-异丙基丙烯酰胺共聚,制得聚N-异丙基丙烯酰胺,纳米SiO2复合水凝胶,并用FT-IR和SEM对产物进行了表征,研究了凝胶的溶胀动力学,消溶胀动力学和温度敏感性,实验结果表明,纳米SiO2的引入,改善了聚N-异丙基丙烯酰胺水凝胶在低温时的溶胀性能和在高温时对水的释放性能,并讨论了引起这些性能改变的原因。     

PVA/PAA thermo-crosslinking hydrogel fiber: preparation and pH-sensitive properties in electrolyte solution

The preparation of thermo-crosslinking hydrogel fibers composed of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) was presented. The hydrogel fiber was prepared by extruding the spinning dope from in situ polymerization of acrylic acid in the presence of PVA into coagulating bath of saturated ammonium sulfate aqueous solution. The network was formed by thermally heating the dried fibers under vacuum. The final hydrogel fibers exhibit pH-sensitive behavior and show hysteresis loop in the pH range from 2.5 to 12.5. The pH value at which the swelling ratio of the fiber had a jump shifted to lower value with increasing the PAA content within the network. Increasing the heating temperature and time for the fibers, the swelling ratio decreased and the jump point pH shifted to higher pH value. The oscillatory swelling/contracting behavior of the hydrogel fiber exhibited a well reversible pH-responsive property.     

HPAN/SPI水凝胶纤维的PH刺激响应性能

探索了聚丙烯腈(PAN)和大豆分离蛋白(SPI)在NaOH水溶液中进行PAN碱解,然后挤到凝固浴中凝固、交联,制备水解聚丙烯腈(HPAN)／SPI水凝胶纤维的方法。通过测定凝胶纤维的平衡溶胀伸长率和溶胀伸长率,观察到HPAN／SPI水凝胶纤维的滞后和可逆的伸长／收缩行为,同时在不同组成的凝胶纤维中,随着PAN含量的逐渐增大,水凝胶纤维的响应速率呈现由小到大然后减小的变化规律,当mPAN／mspt=6／4时有最好的响应性能。     

聚富马酸丙二醇酯/羟基磷灰石复合多孔水凝胶的制备及其矿化性能研究

采用二步法合成了可降解的聚富马酸丙二醇酯(poly(propylene fumarate),PPF),并和N-乙烯基吡咯烷酮(N-vinyl pyrrolidone,NVP)共聚,以1,4-二氧六环为溶剂,通过改变溶剂的量制备了溶胀性能不同的PPF水凝胶.采用万能力学测试仪和扫描电子显微镜分别表征了水凝胶的压缩模量和形貌结构.选择20％ PPF和10％ NVP的聚合体系,预掺3％的纳米羟基磷灰石(hydroxyapatite,HA),以氯化钠粒子为致孔剂,制备了孔径在280～450 μm的纳米复合多孔水凝胶,使其压缩模量提高了61％.模拟体液矿化10天的结果显示,磷灰石成核位点的存在和良好的与外界液体环境物质交换的能力,促进了多孔水凝胶表面磷灰石的沉积,说明HA的复合可以有效提高PPF多孔水凝胶的成骨活性.     

Swelling Kinetics of Microgels Embedded in a Polyacrylamide Hydrogel Matrix

Composite hydrogels—macroscopic hydrogels with embedded microgel particles—are expected to respond to external stimuli quickly because microgels swell much faster than bulky gels. In this work, the kinetics of the pH‐induced swelling of a composite hydrogel are studied using turbidity measurements. The embedded microgel is a pH‐ and thermosensitive poly(N‐isopropylacrylamide‐co‐acrylic acid) microgel and the hydrogel matrix is polyacrylamide. A rapid pH‐induced swelling of the embedded microgel particles is observed, confirming that composite hydrogels respond faster than ordinary hydrogels. However, compared with the free microgels, the swelling of the embedded microgel is much slower. Diffusion of OH^? into the composite hydrogel film is identified as the main reason for the slow swelling of the embedded microgel particles, as the time of the pH‐induced swelling of this film is comparable to that of OH^? diffusion into the film. The composition of the hydrogel matrix does not significantly change the characteristic swelling time of the composite hydrogel film. However, the swelling pattern of the film changes with composition of the hydrogel matrix.     

蚕丝纤维/丝蛋白复合材料力学性能的优化

在制备具有良好力学性能的蚕丝纤维/丝蛋白复合材料的基础上,采用力学测试、扫描电镜以及广角X-射线衍射等手段,考察了溴化锂预处理和甲醇后处理这两种方法对蚕丝纤维/丝蛋白界面性能的影响.力学测试的结果表明,在相同纤维含量(如20 wt％)的情况下,采用6 mol L-1溴化锂对定向排列的蚕丝纤维预处理10 min,所得的蚕...     

Preparation and characterization of novel silk fibroin/2-(N,N-dimethylamino)ethyl methacrylate based composite hydrogels with enhanced mechanical properties for controlled release of cefixime

Hydrogels with improved mechanical properties have been particularly attractive for their applications in the biomedical area including wound healing. For this purpose, a series of novel composite hydrogels based on silk fibroin (SF) and 2-(N,N-dimethylamino) ethyl methacrylate (DMAEMA) were fabricated. The swelling and mechanical tests indicated that an optimum design of hydrogel was essential to provide a high degree of water uptake, higher tensile strength and elongation at break values. Here, the S40D60 was exhibited superior swelling and strong mechanical characteristics than all the other hydrogels with different compositions. Furthermore, it was observed that the cefixime was released from the formulation of S40D60 in a sustainable manner and the drug release rate can be controlled by pH of the dissolution medium. According to these findings, it is suggested that the optimal formulation of S40D60 would be effectively performed in situ drug therapy for wound healing.     

聚N-异丙基丙烯酰胺/纳米SiO_2复合水凝胶的合成及溶胀性能

通过纳米SiO2的表面功能化,在其表面引入乙烯基功能基团,在H2OTHF的混合溶剂中,超声分散后,交联剂N,N′亚甲基双丙烯酰胺存在时,于25℃下使其与N异丙基丙烯酰胺共聚,制得聚N异丙基丙烯酰胺纳米SiO2复合水凝胶,并用FTIR和SEM对产物进行了表征.研究了凝胶的溶胀动力学,消溶胀动力学和温度敏感性.实验结果表明,纳米SiO2的引入,改善了聚N异丙基丙烯酰胺水凝胶在低温时的溶胀性能和在高温时对水的释放性能,并讨论了引起这些性能改变的原因.     

Dual-functional composite with anticoagulant and antibacterial properties based on heparinized silk fibroin and chitosan

Heparinized biomaterials exhibit great anticoagulant properties. However, they promote proliferation of Staphylococcus aureus (S. aureus) and therefore cause infection within the bloodstream upon implantation in vivo. In the present study, an interesting dual-functional composite with anticoagulant and antibacterial properties based on heparinized silk fibroin and chitosan was synthesized. First, heparin was grafted onto the silk fibroin by covalent immobilization with N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide (EDC) and N-hydroxysuccinimide (NHS). All data gathered from Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and elemental analysis (EA) indicated that the heparin was successfully immobilized onto the silk fibroin. The dual-functional composite of heparinized silk fibroin and chitosan was then fabricated by a blending method. The anticoagulant activity of the heparinized materials was evaluated using the prothrombin time (PT), activated partial thromboplastin time (APTT) and thrombin time (TT). The results showed that both heparinized silk fibroin and the composite material exhibited better hemocompatibility in comparison with single silk fibroin or chitosan. The antibacterial property of the materials was investigated by the pour-plate method. Results further suggested that the composite antibacterial property with respect to S. aureus was significantly enhanced. The dual-functionality of the composite material may supply a potential choice in blood contact devices.