循环流化床燃煤过程NO、N2O和SO2的排放行为研究

在30kW循环流化床装置上进行了中国西部三种煤的燃烧实验，考查了燃烧温度、空气分级、空气过剩系数、固体颗粒循环料率和煤种等因素对NO、N2O、SO2污染物排放的影响。结果表明，强化空气分级可显著降低高挥发分煤种NO的生成量，但对N2O影响不大；增加空气过剩系数同时增加了NO与N2O的排放；增加固体循环料率显著降低NO生成量，但N2O排放略有增加；高阶煤燃烧生成较多N2O，低阶煤生成较多NO。燃烧温度1120K、过剩空气系数1.25下约85%燃料中N转化为N。实验范围内改变操作参数不影响SO2与CO排放量。     

NO和O2的反应

无色NO和空气中O2一经接触即生成红棕色的NO2.     

NO和O2的反应

无色NO和空气中O2一经接触即生成红棕色的NO2.……     

二氧化氮的制取及与水反应实验器

正高一年级化学课本"氮的循环"[1]一节中,涉及了NO2的产生及其与H2O反应的2个实验。教材中,NO2的制取采用试管作反应器,产物NO2(一种有毒气体)直接排放到空气中,造成环境污染,危害师生健康,这不是一个绿色化的教学实验。笔者经过系统的研究、探讨及数百次的实验[2],研制出"二氧化氮的制取及与水反应实验器"[3](以下简称实验器)。实验器已获得国家发明专利,专利号:201120472676.2,图2所示的实验器已在本校     

介质阻挡放电引发氮氧化物等离子体化学反应

在523 K介质阻挡放电条件下,研究了不同气体组分体系中NO的转化.实验表明,在无氧体系(NO/N2)中,转化的NO主要分解为N2和O2.在富氧(NO/O2/N2)条件下,由于NO和NO2的生成, NO的转化率最低.体系中加入C2H4(NO/C2H4/N2)时, NO转化率与NO/N2体系几乎一样,与NO相比,生成的O更易与C2H4作用,几乎没有NO2的生成.当C2H4和O2共存时(NO/O2/C2H4/N2),NO主要被氧化为NO2.当能量密度为125 J•L－1时, 与其它体系相比,NO/O2/C2H4/N2体系中NO转化率和NO2生成量最大,转化每个 NO分子能耗最小(61 eV).体系中C2H4主要被氧化为CO.四个体系中N2O的生成量都较少.讨论了介质阻挡放电条件下上述四个体系可能的反应机制.     

钛铝载体的合成及负载CuO对NO催化性能研究

以TiCl4为原料合成了TiO2/[[alpha]]-Al2O3载体. 在色谱-微反流动法反应装置上考察了CuO/15%(w, 下同)TiO2/[alpha]-Al2O3系列催化剂对NO+CO 的反应性能. 结果表明上述催化剂对NO+CO 反应表现出较好的活性, 其中12%CuO/15%TiO2/[alpha]-Al2O3反应活性最佳. 空气和H2 预处理后, NO 完全转化的温度分别为300C[[deg]]和275C[deg].通过H2-TPR、XRD 和FT-IR 等技术表征, 发现适量TiO2能促进CuO 在钛铝载体上的分散. TPR 结果显示12%CuO/15%TiO2/[alpha]-Al2O3在整个TPR 过程中出现四个还原峰, 琢和酌还原峰分别是钛铝载体表面裸露的TiO2上高度分散的CuO 和晶相CuO 的还原；茁和啄还原峰为钛铝载体上高度分散的CuO 和晶相CuO 的还原. FT-IR实验表明NO和CO 在经H2气氛预处理的催化剂表面上吸附较强, 且生成了N2O 和NO2等物种；NO+CO混合气在经空气和H2预处理的催化剂表面吸附时, 出现了N2O吸收峰, 峰温分别为200C[deg]和150C[deg].     

关于NO_2、NO与Na_2O_2反应的探究

关于NO2、NO与Na2O2能否反应的问题，一些文献［1，2］已有了肯定，但其反应结果却与本人多次实验结果有较大出入；且NO与Na2O2反应时，也未保证NO的纯度，尚难说明问题。现将本人实验及其结果报告如下。一、实验及结果1．当Na2O2过量时，NO2与Na2O2。的反应在干燥的锥形瓶中加两小匙过氧化钠（保证纯度）粉末，将NO2通入锥形瓶中，迅速塞上瓶塞，可看到锥形瓶中NO。的棕色迅速变为无色。反应剧烈，放出大量的热，使锥形瓶瓶底烫手（若NO。气流较大，能使Na。0。表面闪现火花，以致使锥形瓶炸裂）。反应结束后，打开瓶塞（很难打…     

模拟雷雨条件下氮气和氧气反应的数字化实验探究

设计了高压放电条件下N2和O2反应的实验装置,利用氧气传感器和压强传感器测量放电后O2浓度的变化,停止放电后O2浓度进一步减小,说明反应过程中生成了NO。向反应后的体系中注入紫色石蕊溶液,模拟雨水中NO2与水反应,可以观察到红棕色变淡,紫色石蕊溶液变红,且氧气和压强传感器数值进一步减小,说明NO2与水反应生成酸性物质,同时生成了NO。     

低温等离子体转化NO/O2/N2气氛中NO的实验研究

通过建立低温等离子体实验系统, 研究了介质阻挡放电型低温等离子体反应器作用于NO/O2/N2混合气体系时, NO, O2初始浓度对NO的转化效率的影响以及NOx, O3浓度随能量密度的变化关系. 低温等离子体作用于NO/O2/N2混合气体系时, NO同时发生氧化还原反应, 氧化反应占主导地位, 大部分NO转化为NO2; NO转化率随O2, NO初始浓度增大而降低, 能量密度在450～600 J/L时转化率较高; 产生的O3浓度随能量密度的增大呈先增后减的趋势.     

水蒸气对甲烷在金属铁表面还原NO行为的影响

采用程序控温电加热水平陶瓷管反应器,在N2气氛和模拟烟气气氛中、300~1100℃下,研究了水蒸气对甲烷在金属铁表面还原NO行为的影响,并对反应前、后铁样品进行了X光衍射(XRD)、扫描电子显微镜(SEM)及X光电子能谱(XPS)等表征。结果表明,水蒸气对甲烷在金属铁表面还原NO行为的影响较小。在N2气氛中,水蒸气参与了金属铁的氧化;与无水蒸气时相比,水蒸气存在时NO还原效率有所下降。当水蒸气含量从2.5%增加到7%时,由于水蒸气对金属铁的氧化导致其表面形成疏松的微观孔隙,使得NO的还原效率随水蒸气含量的增加而提高。甲烷则参与了铁氧化物的还原,使铁样品表面形成相对致密的Fe3O4和FeO氧化层,不利于NO与金属铁的接触,使得NO的还原效率低于无甲烷时的结果。在模拟烟气条件下,水蒸气使得甲烷在金属铁表面还原NO的效率增加;在1050℃下,反应段过量空气系数SR1=0.7和燃尽段过量空气系数SR2=1.2时,含7%的H2O和无H2O条件下脱硝效率分别为96.7%和90.6%。而在湿烟气中SO2使NO还原效率略有下降。持久性脱硝实验结果表明,当反应温度为1050℃时,在含7%的H2O、0.02%的SO2的模拟烟气中,1.14%的甲烷在金属铁表面持续50h都能保持90%以上的脱硝效率。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.