Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.     

Microstructure and mechanical properties of Al2O3-Al composite coatings deposited by plasma spraying

Al₂O₃ and Al₂O₃-Al composite coatings were prepared by plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction (XRD), while optical microscopy (OM) and scanning electron microscopy (SEM) were employed to investigate the morphology of impacted droplets, polished and fractured surface, and the element distribution in terms of wavelength-dispersive spectrometer (WDS). Mechanical properties including microhardness, adhesion and bending strength, fracture toughness and sliding wear rate were evaluated. The results indicated that the addition of Al into Al₂O₃ was beneficial to decrease the splashing of impinging droplets and to increase the deposition efficiency. The Al₂O₃-Al composite coating exhibited homogeneously dispersed pores and the co-sprayed Al particles were considered to be distributed in the splat boundary. Compared with Al₂O₃ coating, the composite coating showed slightly lower hardness, whereas the coexistence of metal Al phase and Al₂O₃ ceramic phase effectively improved the toughness, strength and wear resistance of coatings.     

有机金属化学气相沉积法制备的Ni/Al2O3纳米复合材料的氢吸附

研究了通过有机金属化学气相沉积技术及单源分子前躯体方法制备的Ni/Al₂O₃纳米复合材料的氢吸附(存储). 在冷壁的有机金属化学气相沉积反应器中,通过降解Ni(acac)₂粉末基底上的[H₂Al(OtBu)]₂制备的Ni/Al₂O₃纳米复合材料. 通过X射线粉末衍射、扫描电镜、透射电镜以及能量色散型X射线荧光光谱等技术表征该复合材料. 采用自制Sievert's设备研究该复合材料的氢吸附(存储),可以储存约2.9%(重量比)的氢.     

Double-ceramic-layer thermal barrier coatings based on La2(Zr0.7Ce0.3)2O7/La2Ce2O7 deposited by electron beam-physical vapor deposition

Double-ceramic-layer (DCL) thermal barrier coatings (TBCs) of La₂(Zr_0.7Ce_0.3)₂O₇ (LZ7C3) and La₂Ce₂O₇ (LC) were deposited by electron beam-physical vapor deposition (EB-PVD). The composition, interdiffusion, surface and cross-sectional morphologies, cyclic oxidation behavior of DCL coating were studied. Energy dispersive spectroscopy and X-ray diffraction analyses indicate that both LZ7C3 and LC coatings are effectively fabricated by a single LZ7C3 ingot with properly controlling the deposition energy. The chemical compatibility of LC coating and thermally grown oxide (TGO) layer is unstable. LaAlO₃ is formed due to the chemical reaction between LC and Al₂O₃ which is the main composition of TGO layer. Additionally, the thermal cycling behavior of DCL coating is influenced by the interdiffusion of Zr and Ce between LZ7C3 and LC coatings. The failure of DCL coating is a result of the sintering of LZ7C3 coating surface, the chemical incompatibility of LC coating and TGO layer and the abnormal oxidation of bond coat. Since no single material that has been studied so far satisfies all the requirements for high temperature applications, DCL coating is an important development direction of TBCs.     

Plasma sprayed Al2O3/FeCrAl composite coatings for electromagnetic wave absorption application

Al₂O₃/FeCrAl composite coatings were fabricated by atmosphere plasma spraying technique. Microstructure and dielectric properties in the frequency range from 8.2 to 12.4 GHz were investigated. The microstructure of composite coatings shows a uniform dispersion of metal particles with litter pores and microcracks in the composite coatings. The relaxation polarization and interfacial polarization in the coatings would contribute to enhance ?′ with rising FeCrAl content, and the associated loss could be considered as a dominating factor enhancing ?″. By calculating the microwave-absorption as a single-layer absorber, for the composite coatings with 41 wt.% FeCrAl content, the reflection loss values exceeding −10 dB are achieved in the frequency range of 9.1-10.6 GHz when the coating thickness is 1.3 mm.     

Atmospheric reactive plasma sprayed Fe-Al2O3-FeAl2O4 composite coating and its property evaluation

In the present study, Fe-Al₂O₃-FeAl₂O₄ composite coatings were successfully deposited by reactive plasma sprayed Al/Fe₂O₃ agglomerated powder. Phase composition and microstructure of the coatings were determined by XRD and SEM. The results indicated that the composite coatings were principally composed of three different phases, i.e. FeAl₂O₄ phase as main framework, dispersed ball-like Fe-rich phase, and small splats of Al₂O₃ phase, and it was thought that the in situ synthesized metal phase was helpful to toughen the coating matrix. According to the results of the indentation and frictional wear tests, the composite coating exhibited excellent toughness and anti-friction properties in comparison with conventional Al₂O₃ monophase coating, though its microhardness value was a little lower than that of Al₂O₃ coating. The formation mechanism and the toughening mechanism of the composite coating were clarified in detail.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy

Composite coatings using pure Al powder blended with α-Al₂O₃ as feedstock were deposited on AZ91D magnesium alloy substrates by cold spray (CS). The content of α-Al₂O₃ in the feedstock was 25 wt.% and 50 wt.%, respectively. The effects of α-Al₂O₃ on the porosity, microhardness, adhesion and tensile strength of the coatings were studied. Electrochemical tests were carried out in neutral 3.5 wt.% NaCl solution to evaluate the effect of α-Al₂O₃ on the corrosion behavior of the coatings. The results showed that the composite coatings possessed lower porosity, higher adhesion strength and tensile strength than cold sprayed pure Al coating. The corrosion current densities of the composite coatings were similar to that of the pure Al coating and much higher than that of bare AZ91D magnesium alloy.     

Microstructure and properties of Ni-Co/nano-Al2O3 composite coatings by pulse reversal current electrodeposition

Ni-Co/nano-Al₂O₃ (Ni-Co/Al₂O₃) composite coatings were prepared under pulse reversal current (PRC) and direct current (dc) methods respectively. The microstructure of coatings was characterized by means of XRD, SEM and TEM. Both the Ni-Co alloy and composite coatings exhibit single phase of Ni matrix with face-centered cubic (fcc) crystal structure, and the crystal orientation of the Ni-Co/Al₂O₃ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with alloy coatings. The hardness, anti-wear property and macro-residual stress were also investigated. The results showed that the microstructure and performance of the coatings were greatly affected by Al₂O₃ content and the electrodeposition methods. With the increasing of Al₂O₃ content, the hardness and wear resistance of the composite coatings enhanced. The PRC composite coatings exhibited compact surface, high hardness, better wear resistance and lower macro-residual stress compared with that of the dc composite coatings.     

Microstructure and properties of TiB2-containing coatings prepared by arc spraying

Low cost arc spraying and cored wires were used to deposit composite coatings consisting of TiB₂ and TiB₂/Al₂O₃ hard particles in a Ni(Cr) and stainless steel 304L matrix. Four coatings were prepared namely Ni(Cr)-TiB₂, Ni(Cr)-TiB₂/Al₂O₃, 304L-TiB₂ and 304L-TiB₂/Al₂O₃. The microstructural characteristics of powders and coatings were observed by scanning electron microscopy (SEM). Phase compositions of powders were analyzed by X-ray diffraction (XRD). Although all the analyzed coatings exhibited similar lamella structure, remarkable differences not only in the morphology of hard phase and matrix but also in the size and distribution of hard phases were observed from one coating to another. Tribological behavior of the coatings was analyzed in room temperature dry sliding wear tests (block-on-ring configuration), under 75 N at low velocity (0.5 m/s). The coatings showed far high wear resistance than low carbon steel substrate under same conditions examined. Wear loss of 304L-TiB₂ and Ni(Cr)-TiB₂ coatings were lower nearly 15 times than that of steel substrate. TiB₂ hard phases in coatings bonded well with metal matrix contributed to high wear resistance.     

Preparation and characterization of the electrodeposited Cr-Al2O3/SiC composite coating

To increase the SiC content in Cr-based coatings, Cr-Al₂O₃/SiC composite coatings were plated in Cr(VI) baths which contained Al₂O₃-coated SiC powders. The Al₂O₃-coated SiC composite particles were synthesized by calcining the precursor prepared by heterogeneous deposition method. The transmission electron microscopy analysis of the particles showed that the nano-SiC particle was packaged by alumina. The zeta potential of the particles collected from the bath was up to +23 mV, a favorable condition for the co-deposition of the particles and chromium. Pulse current was used during the electrodeposition. Scanning Electron Microscopy (SEM) indicated that the coating was compact and combined well with the substrate. Energy dispersive X-ray analysis of Cr-Al₂O₃/SiC coatings demonstrated that the concentration of SiC in the coating reached about 2.5 wt.%. The corrosion behavior of the composite coating was studied by potentiodynamic polarization and electrochemical impedance spectroscopy techniques. The data obtained suggested that the Al₂O₃/SiC particles significantly enhanced the corrosion resistance of the composite coating in 0.05 M HCl solution.     

Laser surface remelting of plasma sprayed nanostructured Al2O3-13wt%TiO2 coatings on titanium alloy

Plasma sprayed nanostructured coatings were successfully fabricated on a titanium alloy (Ti-6Al-4V) substrate using the as-prepared nanostructured Al₂O₃-13wt%TiO₂ feedstock. A CO₂ laser was used to remelt the plasma sprayed coatings. The effects of laser remelting on the phase constituents, microstructure and properties of the ceramic coatings were investigated. The laser remelted coatings (LRmC) possessed a much denser and more homogenous structure and excellent metallurgical bonding to the substrate. The average porosity of the LRmC was reduced to 0.9%, compared with 6.2% of the as-sprayed coatings. The net-like structure in the as-prepared feedstock remained in the coatings before and after laser remelting. The metastable γ-Al₂O₃ phase in the as-sprayed coatings transformed to stable α-Al₂O₃ during laser remelting. The LRmC could remain nanostructure. The microhardness of the coatings was enhanced to 1000-1400 HV_0.3 after laser remelting, which was much higher than that of the plasma sprayed coatings and 2-3 times higher that of the substrate. Significant decreases in surface roughness were also found in the LRmC.     

Deposition and characterization of binary Al2O3/SiO2 coating layers on the surfaces of rutile TiO2 and the pigmentary properties

Binary Al₂O₃/SiO₂-coated rutile TiO₂ composites were prepared by a liquid-phase deposition method starting from Na₂SiO₃·9H₂O and NaAlO₂. The chemical structure and morphology of binary Al₂O₃/SiO₂ coating layers were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, TG-DSC, Zeta potential, powder X-ray diffraction, and transmission electron microscopy techniques. Binary Al₂O₃/SiO₂ coating layers both in amorphous phase were formed at TiO₂ surfaces. The silica coating layers were anchored at TiO₂ surfaces via Si-O-Ti bonds and the alumina coating layers were probably anchored at the SiO₂-coated TiO₂ surfaces via Al-O-Si bonds. The formation of continuous and dense binary Al₂O₃/SiO₂ coating layers depended on the pH value of reaction solution and the alumina loading. The binary Al₂O₃/SiO₂-coated TiO₂ composites had a high dispersibility in water. The whiteness and brightness of the binary Al₂O₃/SiO₂-coated TiO₂ composites were higher than those of the naked rutile TiO₂ and the SiO₂-coated TiO₂ samples. The relative light scattering index was found to depend on the composition of coating layers.     

Preparation of photocatalytic Fe2O3-TiO2 coatings in one step by metal organic chemical vapor deposition

There are two major difficulties in the TiO₂ liquid-solid photocatalytic system: effective immobilization of the TiO₂ particles; and improving the catalytic activity under visible light. To simultaneously solve these two problems, Fe₂O₃-TiO₂ coatings supported on activated carbon fiber (ACF), have been prepared in one step by a convenient and efficient method—metal organic chemical vapor deposition (MOCVD). XRD results revealed that Fe₂O₃-TiO₂ coatings mainly composed of anatase TiO₂, α-Fe₂O₃ phases and little Fe₂Ti₃O₉. The pore structure of ACF was preserved well after loading with Fe₂O₃-TiO₂ coatings. UV-vis diffuse reflectance spectra showed a slight shift to longer wavelengths and an enhancement of the absorption in the visible region for Fe₂O₃-TiO₂ coatings, compared to the pure TiO₂ sample. A moderate Fe₂O₃-TiO₂ loading (13.7 wt%) was beneficial to mineralizing wastewater because the intermediates could be adsorbed onto the surface of photocatalyst following decomposition. The stable performance revealed that the Fe₂O₃-TiO₂ coatings were strongly adhered to the ACF surface, and the as prepared catalysts could be reused showing potential application for wastewater treatment.     

Preparation and wear resistance of pulse electrodeposited Ni-W/Al2O3 composite coatings

The aim of this work is to obtain the electroplating parameters for preparation of Ni-W/Al₂O₃ composite coating with high tungsten content, high micro-hardness and excellent wear resistance by pulse plating procedure. Our results showed that the duty cycle is a dominant parameter for the tungsten content in the coating and the tungsten content increases significantly with increasing duty cycle. The further analysis showed the great influence of tungsten content on micro-hardness of the coating. A maximum micro-hardness of about 859 Hv was obtained in pulse electrodeposited Ni-W/Al₂O₃ composite with tungsten content of 40 wt.% at a peak current density of 20 A/dm², a duty cycle of 80%, a pulse frequency of 1000 Hz and a particle loading of 10 g/L alumina in the plating bath. Although the hardness of Ni-W/Al₂O₃ composite coating was only slightly affected by the alumina content of the deposits prepared in present investigation, the alumina content effect on the tribological characteristic of Ni-W/Al₂O₃ composite coatings is significant. The friction coefficient was lowered to 0.25 and the wear loss was reduced to 1.05 mg by setting the control factors according to the values mentioned above for obtaining the coating with the highest micro-hardness.     

Influences of laser remelting on microstructure of nanostructured Al2O3-13 wt.% TiO2 coatings fabricated by plasma spraying

The effects of laser remelting on microstructure of nanostructured Al₂O₃-13 wt.% TiO₂ ceramic coatings prepared by plasma spraying with agglomerated powders were studied. The microstructure of the feedstock, as-sprayed and laser-remelted coatings were investigated by using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffractometry (XRD). The results indicate that the plasma-sprayed ceramic coating consists of both fully melted regions and partially melted regions. The totally ceramic coating, especially the fully melted regions, has a typical plasma-sprayed lamellar-like structure as the conventional coating, and has some pores. According to the difference of microstructures, the partially melted regions can be divided into liquid-phase sintered regions (a three-dimensional net or skeleton-like structure: Al₂O₃-rich submicron particles embedded in the TiO₂-rich matrix) and solid-phase sintered regions (remained nanoparticles). The lamellar defect of the as-sprayed coating is erased, and the compactness of the coating is improved significantly after laser remelting. The laser-remelted region composed of fine equiaxed grains, which are different from the conventional column-like crystals along the direction of the heat current. Due to the rapid solidification of laser remelting process, there are still some nanoparticles in the remelted region because of an insufficient time for grains growth.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

SMA-g-MPEG comb-like polymer as a dispersant for Al2O3 suspensions

SMA-g-MPEG comb-like polymer is first employed as the dispersant of Al₂O₃ suspensions in this paper. The comb-like polymer has anionic polycarboxylate backbone, which makes the polymer easily absorbed on the cationic surface of Al₂O₃ particles; on the other hand, the comb-like polymer has hydrophilic MPEG side chains, which extend into the solution to provide steric repulsion after the comb-like polymer is absorbed on the surface of Al₂O₃ particles. The adsorption behavior, zeta potential, apparent viscosity, granularity and TEM images of the Al₂O₃ suspensions using SMA-g-MPEG as dispersant are investigated. The addition of SMA-g-MPEG improves the dispersibility and decreases the apparent viscosity of the Al₂O₃ suspension observably. The impacts of the length of side chains on the dispersion of Al₂O₃ suspensions are particularly discussed. The adsorbed molecular number of the dispersant decreased by increasing the length of side chains. The zeta potential of Al₂O₃ suspension is more negative by using comb-like polymer with shorter side chains. Based on the steric repulsion and adsorbed molecular number, SMA-g-MPEG with moderate length of side chain is found to have the best dispersibility for Al₂O₃ suspension.     

Electrodeposition and characterization of Ni-Y2O3 composite

Nano-sized Y₂O₃ particles were codeposited with nickel by electrolytic plating from a nickel sulfate bath. The effects of the incorporated Y₂O₃ on the structure, morphology and mechanical properties (including microhardness, friction coefficient and wear resistant) of Ni-Y₂O₃ composite coatings were studied. It is observed that the addition of nano-sized Y₂O₃ particles shows apparent influence on the reduction potential and pH of the electrolyte. The incorporated Y₂O₃ increases from 1.56 wt.% to 4.4 wt.% by increasing the Y₂O₃ concentration in the plating bath from 20 to 80 g/l. XRD results reveal that the incorporated Y₂O₃ particles favour the crystal faces (2 0 0) and (2 2 0). SEM and AFM images demonstrate that the addition of Y₂O₃ particles causes a smooth and compact surface. The present study also shows that the codeposited Y₂O₃ particles in deposits decrease the friction coefficient and simultaneously reduce the wear weight loss. Ni-Y₂O₃ composite coatings reach their best microhardness and tribological properties at Y₂O₃ content 4.4 wt.% under the experiment conditions.     

Structural properties of Al2O3 dielectrics grown on TiN metal substrates by atomic layer deposition

We investigated on the structural properties of Al₂O₃ dielectrics grown on TiN metal substrates using an atomic layer deposition technique with tri-methyl-aluminum and either O₃ or H₂O as the precursor and oxidant, respectively. The structural and morphological features of these films were examined by atomic force microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy measurements. We find that Al₂O₃ dielectric films with the O₃ oxidant exhibit a rough morphology, a thick TiO₂ film, and a small amount of contaminants such as carbon and hydrogen. The reason for the rapid diffusion of oxygen atoms into the TiN lattice leads to the formation of TiO₂ layer on the TiN substrate. This is due to the higher oxidation potential of the O₃ compared to the H₂O.