Hyperbranched fluoropolymer and linear poly(ethylene glycol) based amphiphilic crosslinked networks as efficient antifouling coatings: An insight into the surface compositions,topographies, and morphologies

Polymer coatings with features of differing hydrophilicity, mobility, and topography, distributed across a substrate in microscopic and nanoscopic patches were designed as complex materials equipped with sufficient variability in composition, structure, and dynamics to inhibit interactions associated with biomacromolecular fouling. These complex polymer coatings were prepared by the in situ phase separation and crosslinking of mixtures of hyperbranched fluoropolymer (HBFP) and diamino‐terminated poly(ethylene glycol) (PEG), for which the degree of crosslinking, compositions, topographies, and morphologies were varied by alteration of the PEG/HBFP stoichiometries (14, 29, 45, and 55 wt % PEG). This article examines the physicochemical details of HBFP–PEG network coatings prepared on glass substrates, functionalized by 3‐aminopropyltriethoxysilane, as characterized by atomic force microscopy (AFM), contact‐angle measurements, X‐ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), and thermogravimetric analysis. Upon incubation in water or artificial seawater, the surfaces underwent reconstruction, which was believed to be driven by the swelling of the PEG domains and the energetic favorability offered by the segregation of PEG to the solid–water interface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6193–6208, 2004     

Unusual, promoted release of guests from amphiphilic cross-linked polymer networks

Hyperbranched fluoropolymer-poly(ethylene glycol) (HBFP-PEG) cross-linked networks have been found to exhibit capabilities for the encapsulation of high levels of geraniol guest molecules coupled with unusually rapid release of the volatile compound. The promotion of the release of the volatile fragrance geraniol, observed as decreasing volatilization temperatures and increasing volatilization rates by thermogravimetric analyses, was found to be dependent upon the HBFP-PEG network composition, with increasing effects from decreasing wt % PEG and a maximum effect occurring at 5 wt % PEG.     

含氟/PEG的有机硅基双亲防污涂层的制备及性能

以不同分子量的端氢硅油(PDMS)和聚乙二醇二烯丙基醚(PEGDE)为原料,通过硅氢加成合成了系列双键封端的含有机硅和聚乙二醇(PEG)链段的多嵌段共聚物(PDMS-b-PEG)m,再用三甲氧基氢硅烷进行端基官能化,生成三甲氧基硅烷封端的多嵌段聚合物,即含PEG前驱物.含PEG前驱物、含氟前驱物(FMS-9922)与有机硅基体树脂通过缩合聚合制备了含PEG的氟硅双亲弹性防污涂层.通过核磁共振氢谱、红外光谱对PEG前驱物的结构进行了表征.吸水率、SEM-EDS和接触角测试考察了含PEG前驱物中疏水链段的长度,含氟前驱物的含量对涂层表面重排的影响,结果表明PEG前驱物中疏水链段越长,涂层的吸水率越低,在水中越稳定,且表面不易发生重排.而含氟前驱物的加入能促使PEG链段向表面方向迁移.抗蛋白、抗菌和抗藻附着性能测试表明:含有FMS-9922的样品防污性能均优于不含FMS-9922的样品,而且随着FMS-9922用量增加,涂层防污性能呈上升趋势;但是FMS-9922用量太高时,体系相容性下降,防污性能也随之变差,故FMS-9922的含量控制在7%为宜.     

Complex amphiphilic networks derived from diamine‐terminated poly(ethylene glycol) and benzylic chloride‐functionalized hyperbranched fluoropolymers

Amphiphilic copolymer networks were prepared from hyperbranched fluoropolymer (HBFP*, M_n = 38 kDa, by atom transfer radical‐self condensing vinyl copolymerization) and linear diamine‐terminated poly(ethylene glycol) (DA‐PEG, M_n = 1,630 Da). Model studies found that the crosslinking mechanism occurred at ambient temperature as a result of reaction between DA‐PEG and the benzylic chlorides of HBFP*. These networks underwent covalent attachment to glass microscope slides derivatized with 3‐aminopropyltriethoxysilane, whereupon gel percent studies at various weight percentages of DA‐PEG to HBFP* found that curing could be achieved at lower temperatures and shortened time periods relative to the previously reported parent HBFP–PEG system. Thermogravimetric analysis revealed that the crosslinked materials gave no evident mass loss up to 250 °C. Differential scanning calorimetry of the complex amphiphilic networks showed a suppressed glass transition temperature, relative to that observed for neat HBFP*, and multiple melting DA‐PEG endotherm(s) near 30 °C. The films possessed a topographically‐complex surface with features that increased in tandem with an increase in the ratio of DA‐PEG to HBFP*, as detected by atomic force microscopy and quantified by increased rms roughness values. Internal reflection infrared imaging revealed a heterogeneous surface composition and confirmed that the domain sizes increased as the weight percent of DA‐PEG increased. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4782–4794, 2006     

Formation of antifouling functional coating from deposition of a zwitterionic-co-nonionic polymer via “grafting to” approach

We develop a new process for the preparation of synergistic antifouling functional coatings on gold surfaces via a “grafting to” approach. The strategy includes a synthetic step of polymer brushes that consist of poly (ethylene glycol) (PEG) and zwitterionic side chains via a typical reversible-addition fragmentation chain transfer (RAFT) polymerization process, and a subsequent deposition of the polymer brushes onto a gold substrate. The presence of PEG and zwitterion chains on these polymer brush-coated gold surfaces has been proved to have a synergistic effect on the final antifouling property of the coating. PEG chains lower the electrostatic repulsion between zwitterionic polymer chains and increase their graft density on gold surfaces, while zwitterionic polymer effectively improves the antifouling property that is offered by PEG chains alone. Protein adsorption and cell attachment assays tests are conducted to confirm that this copolymer layer on gold surface has a pronounced resistance against proteins such as Bovine serum albumin and Lysozyme. Importantly, the antifouling property can be systematically adjusted by varying the molar ratio of PEG to zwitterionic chains in the final coating copolymer.     

Insights into the mobility of methyl-bearing side chains in proteins from (3)J(CC) and (3)J(CN) couplings

Side-chain dynamics in proteins can be characterized by the NMR measurement of (13)C and (2)H relaxation rates. Evaluation of the corresponding spectral densities limits the slowest motions that can be studied quantitatively to the time scale on which the overall molecular tumbling takes place. A different measure for the degree of side-chain order about the C(alpha)-C(beta) bond (chi(1) angle) can be derived from (3)J(C)(')(-)(C)(gamma) and (3)J(N)(-)(C)(gamma) couplings. These couplings can be measured at high accuracy, in particular for Thr, Ile, and Val residues. In conjunction with the known backbone structures of ubiquitin and the third IgG-binding domain of protein G, and an extensive set of (13)C-(1)H side-chain dipolar coupling measurements in oriented media, these (3)J couplings were used to parametrize empirical Karplus relationships for (3)J(C)(')(-)(C)(gamma) and (3)J(N)(-)(C)(gamma). These Karplus curves agree well with results from DFT calculations, including an unusual phase shift, which causes the maximum (3)J(CC) and (3)J(CN) couplings to occur for dihedral angles slightly smaller than 180 degrees, particularly noticeable in Thr residues. The new Karplus curves permit determination of rotamer populations for the chi(1) torsion angles. Similar rotamer populations can be derived from side-chain dipolar couplings. Conversion of these rotamer populations into generalized order parameters, S(J)(2) and S(D)(2), provides a view of side-chain dynamics that is complementary to that obtained from (13)C and (2)H relaxation. On average, results agree well with literature values for (2)H-relaxation-derived S(rel)(2) values in ubiquitin and HIV protease, but also identify a fraction of residues for which S(J,D)(2) < S(rel)(2). This indicates that some of the rotameric averaging occurs on a time scale too slow to be observable in traditional relaxation measurements.     

Efficient and robust coatings using poly(2-methyl-2-oxazoline) and its copolymers for marine and bacterial fouling prevention

Molecular design, fabrication, and properties of thin-film coatings based on poly(2-methyl-2-oxazoline) (PMOX) and its copolymers were investigated to tackle problem of marine and bacterial fouling prevention. The ultraviolet crosslinkable macromonomer poly(2-methyl-2-oxazoline) dimethylacrylate was synthesized by cationic ring-opening polymerization in a microwave reactor initiated by 1,4-dibromobutane. In order to study the charge effect of the PMOX coatings on the adhesion of fouling organisms, PMOX surfaces with negative, neutral, and positive ζ-potential values were prepared by copolymerization with the positively charged monomer [2-(methacryloyloxy)-ethyl]trimethylammonium chloride. The coatings were stable in sea water for at least 1 month without significant reduction in the film thickness. The marine antifouling activity was evaluated against barnacle cyprids Amphibalanus amphitrite and algae Amphora coffeaeformis. Results showed that PMOX coatings provide effective reduction of the settlement regardless of the molar mass and surface charge of the polymer. Bacterial adhesion test showed that PMOX coatings effectively reduce Staphylococcus aureus and Escherichia coli adhesion. Owing to its good stability and antifouling activity PMOX has a great potential as antifouling coating for marine antifouling applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016, 54, 275–283     

溶菌酶蛋白在聚合物防污膜表面的吸附

采用分子动力学模拟方法比较了溶菌酶蛋白在两种典型聚合物防污材料聚乙二醇(PEG)和聚二甲基硅氧烷(PDMS)表面的吸附行为, 在微观上探讨了聚合物膜表面性质对蛋白质吸附的影响. 根据蛋白质与聚合物膜之间的相互作用、能量变化及表面水化层分子的动力学行为, 解释了PEG防污涂层相对于PDMS表面具有更佳防污效果的原因: (1) 相比PDMS涂层, 蛋白质与PEG涂层的结合能量较低, 使其结合更加疏松; (2) 蛋白质吸附到材料表面要克服表面水化层分子引起的能障, PEG表面与水分子之间结合紧密, 结合水难于脱附, 造成蛋白质在其表面的吸附需要克服更高的能量, 不利于蛋白质的吸附.     

溶菌酶蛋白在聚合物防污膜表面的吸附

采用分子动力学模拟方法比较了溶菌酶蛋白在两种典型聚合物防污材料聚乙二醇(PEG)和聚二甲基硅氧烷(PDMS)表面的吸附行为,在微观上探讨了聚合物膜表面性质对蛋白质吸附的影响.根据蛋白质与聚合物膜之间的相互作用、能量变化及表面水化层分子的动力学行为,解释了PEG防污涂层相对于PDMS表面具有更佳防污效果的原因:(1)相比PDMS涂层,蛋白质与PEG涂层的结合能量较低,使其结合更加疏松;(2)蛋白质吸附到材料表面要克服表面水化层分子引起的能障,PEG表面与水分子之间结合紧密,结合水难于脱附,造成蛋白质在其表面的吸附需要克服更高的能量,不利于蛋白质的吸附.     

Amphiphilic and hydrophobic surface patterns generated from hyperbranched fluoropolymer/linear polymer networks: Minimally adhesive coatings via the crosslinking of hyperbranched fluoropolymers

Hyperbranched fluoropolymers (HBFPs), based on benzyl ether linkages and having a large number of pentafluorophenyl chain ends, were crosslinked by a reaction with diamino-terminated poly(ethylene glycol) (PEG) or diamino-terminated poly(dimethyl siloxane) (PDMS) to form hyperbranched–linear copolymer networks of different compositions, structures, and properties. The crosslinking reactions involved the nucleophilic aromatic substitution of the pentafluorophenyl para-fluorines of HBFP by the amine functionalities of the respective telechelic linear segments. The contact angles, differential scanning calorimetry, thermogravimetric analysis, tensile measurements, and atomic force microscopy (AFM) were used to characterize the resulting network film samples. The surface wettability of the crosslinked materials was affected by the nature and amount of the linear polymer crosslinking agent employed. Amphiphilic polymer networks were formed by the incorporation of diamino-terminated PEG as a crosslinker, whereas diamino-terminated PDMS produced polymer networks of a hydrophobic character. The mechanical properties improved upon crosslinking, as measured by tensile testing. The mechanical integrity of the films was also found to improve upon crosslinking, as measured by AFM machining protocols. The AFM images revealed topographical morphologies that appeared to be the result of phase segregation of HBFP from PEG or PDMS; the dimensions of the phase-segregated domains were dependent on the stoichiometry of HBFP to the linear polymer and the thickness of the coating. As the content of PEG increased, fouling by human fibrinogen, used as a model protein, decreased. Further studies are in progress to determine the effects of the surface composition, morphology, and topography on the biofouling characteristics. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3531–3540, 2003     

A general approach to controlling the surface composition of poly(ethylene oxide)-based block copolymers for antifouling coatings

To control the surface properties of a polystyrene-block-poly(ethylene oxide) diblock copolymer, perfluorinated chemical moieties were specifically incorporated into the block copolymer backbone. A polystyrene-block-poly[(ethylene oxide)-stat-(allyl glycidyl ether)] [PS-b-P(EO-stat-AGE)] statistical diblock terpolymer was synthesized with varying incorporations of allyl glycidyl ether (AGE) in the poly(ethylene oxide) block from 0 to 17 mol %. The pendant alkenes of the AGE repeat units were subsequently functionalized by thiol-ene chemistry with 1H,1H,2H,2H-perfluorooctanethiol, yielding fluorocarbon-functionalized AGE (fAGE) repeat units. (1)H NMR spectroscopy and size-exclusion chromatography indicated well-defined structures with complete functionalization of the pendant alkenes. The surfaces of the polymer films were characterized after spray coating by X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure spectroscopy (NEXAFS), showing that the P(EO-stat-fAGE) block starts to compete with polystyrene to populate the surface after only 1 mol % incorporation of fAGE. Increasing the incorporation of fAGE led to an increased amount of perfluorocarbons on the surface and a decrease in the concentration of PS. At a fAGE incorporation of 8 mol %, PS was not detected at the surface, as measured by NEXAFS spectroscopy. Water contact angles measured by the captive-air-bubble technique showed the underwater surfaces to be dynamic, with advancing and receding contact angles varying by >20°. Protein adsorption studies demonstrated that the fluorinated surfaces effectively prevent nonspecific binding of proteins relative to an unmodified PS-b-PEO diblock copolymer. In biological systems, settlement of spores of the green macroalga Ulva was significantly lower for the fAGE-incorporated polymers compared to the unmodified diblock and a polydimethylsiloxane elastomer standard. Furthermore, the attachment strength of sporelings (young plants) of Ulva was also reduced for the fAGE-containing polymers, affirming their potential as fouling-release coatings.     

Cationic poly(methacryl oxyethyl trimethylammonium) and its poly(ethylene glycol)‐grafted analogue as capillary coating materials in electrophoresis

Cationic polyelectrolytes were synthesized and used as semipermanent coating materials for capillaries in electrophoresis. The polyelectrolytes used were a homopolymer of poly(methacryl oxyethyl trimethylammonium chloride) (PMOTAC) and its poly(ethylene glycol) (PEG)‐grafted analogue. Two PMOTAC polyelectrolytes, with molar masses of 85,000 and 300,000 g/mol, and PEG‐grafted PMOTAC with a molar mass of 280,000 g/mol were synthesized and then characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. Attachment of the polyelectrolytes to the wall of the fused silica capillary for electrophoresis caused the electroosmotic flow (EOF) to reverse. The polyelectrolyte coatings were tested over the pH range 2–11 at different buffer ionic strengths, and the most stable and strongest anodic EOFs were obtained at acidic pH values with low ionic strength buffers. Between runs the capillary is merely rinsed for 2 or 3 min with the background electrolyte solution. With the PMOTAC coatings at pH values ≤5, the RSDs of the EOFs were less than 2.9% after 60 injections. The effects of the molar mass of the polycation and of PEGylation of PMOTAC on the interactions between the polycations and basic proteins were studied at acidic pH values. The differences in the effective electrophoretic mobilities, resolution values, and plate numbers of the proteins with the different coatings were due to the EOF, as demonstrated through calculations of reduced mobilities, relative resolution values, and relative plate numbers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2655–2663, 2007     

Radical quantum yields from formaldehyde photolysis in the 30,400-32,890 cm(-1) (304-329 nm) spectral region: detection of radical photoproducts using pulsed laser photolysis-pulsed laser induced fluorescence

The relative quantum yield for the production of radical products, H + HCO, from the UV photolysis of formaldehyde (HCHO) has been measured using a pulsed laser photolysis–pulsed laser induced fluorescence (PLP–PLIF) technique across the 30,400–32,890 cm(–1) (304–329 nm) spectral region of the ?(1)A2–X?(1)A1 electronic transition. The photolysis laser had a bandwidth of 0.09 cm(–1), which is slightly broader than the Doppler width of a rotational line of formaldehyde at 300 K (0.07 cm(–1)), and the yield spectrum shows detailed rotational structure. The H and HCO photofragments were monitored using LIF of the OH radical as a spectroscopic marker. The OH radicals were produced by rapid reaction of the H and HCO photofragments with NO2. This technique produced an “action” spectrum that at any photolysis wavelength is the product of the H + HCO radical quantum yield and HCHO absorption cross section at the photolysis wavelength and is a relative measurement. Using the HCHO absorption cross section previously obtained in this laboratory, the relative quantum yield was determined two different ways. One produced band specific yields, and the other produced yields averaged over each 100 cm(–1). Yields were normalized to a value of 0.69 at 31,750 cm(–1) based on the current recommendation of Sander et al. (Sander, S. P.; Abbatt, J.; Barker, J. R.; Burkholder, J. B.; Friedl, R. R.; Golden, D. M.; Huie, R. E.; Kolb, C. E.; Kurylo, M. J.; Moortgat, G. K.; et al. Chemical Kinetics and Photochemical Data for Use in Atmospheric Studies, Evaluation No. 17; Jet Propulsion Laboratory: Pasadena, CA, USA, 2011). The resulting radical quantum yields agree well with previous experimental studies and the current JPL recommendation but show greater wavelength dependent structure. A significant decrease in the quantum yield was observed for the 5(0)(1) + 1(0)(1)4(0)(1) combination band centered at 31,125 cm(–1). This band has a low absorption cross section and has little impact on the calculated atmospheric photodissociation rate but is a further indication of the complexity of HCHO photodissociation dynamics.     

A high-frequency and high-field EPR study of new azide and fluoride mononuclear Mn(III) complexes

The isolation, structural characterization and electronic properties of three new six-coordinated Mn(III) complexes, [Mn(bpea)(F)(3)] (1), [Mn(bpea)(N(3))(3)] (2), and [Mn(terpy)(F)(3)] (3) are reported (bpea = N,N-bis(2-pyridylmethyl)-ethylamine; terpy = 2,2':6',2' '-terpyridine). As for [Mn(terpy)(N(3))(3)] (4) (previously described by Limburg J.; Vrettos J. S.; Crabtree R. H.; Brudvig G. W.; de Paula J. C.; Hassan A.; Barra A-L.; Duboc-Toia C.; Collomb M-N. Inorg. Chem. 2001, 40, 1698), all these complexes exhibit a Jahn-Teller distortion of the octahedron characteristic of high-spin Mn(III) (S = 2). The analysis of the crystallographic data shows an elongation along the tetragonal axis of the octahedron for complexes 1 and 3, while complex 2 presents an unexpected compression. The electronic properties were investigated using a high-field and high-frequency EPR study performed between 5 and 15 K (190-575 GHz). The spin Hamiltonian parameters determined in solid state are in agreement with the geometry of the complexes observed in the crystal structures. A negative D value found for 1 and 3 is related to the elongated tetragonal distortion, whereas the positive D value determined for 2 is in accordance with a compressed octahedron. The high E/D values, in the range of 0.103 to 0.230 for all complexes, are correlated with the highly distorted geometry present around the Mn(III) ion. HF-EPR experiments were also performed on complex 1 in solution and show that the D value is the only spin Hamiltonian parameter which is slightly modified compared to the solid state (D = -3.67 cm(-1) in solid state; D = -3.95 cm(-1) in solution).     

Structure and conformation of bis(acetylacetonato)oxovanadium(IV) and bis(maltolato)oxovanadium(IV) in solution determined by electron nuclear double resonance spectroscopy

The structure and conformation of bis(acetylacetonato)oxovanadium(IV) [VO(acac)(2)] and bis(maltolato)oxovanadium(IV) [VO(malto)(2)] in frozen methanol have been determined by application of electron nuclear double resonance (ENDOR) spectroscopy. The positions of inner- and outer-sphere-coordinated solvent were assigned by ENDOR through use of selectively deuterated analogues of methanol. Similarly, the methyl and methylinyl proton resonance features of VO(acac)(2) were identified by site-selective deuteration. For VO(acac)(2), the ENDOR-determined metal-proton distances were best accounted for by a complex of tetragonal-pyramidal geometry, essentially identical to that determined by X-ray crystallography [Dodge, R. P.; Templeton, D. H.; Zalkin, A. J. Chem. Phys. 1961, 35, 55] but with an inner-sphere solvent molecule coordinated trans to the vanadyl oxygen and an axially positioned solvent molecule hydrogen-bonded to the vanadyl oxygen. In contrast to its trans conformation in crystals [Caravan, P.; et al. J. Am. Chem. Soc. 1995, 117, 12759], the VO(malto)(2) complex was found in a cis conformation whereby the donor oxygen atoms of one maltolato ligand occupied equatorial coordination sites. One of the donor oxygen atoms of the second maltolato ligand occupied the axial coordination site opposite the vanadyl oxygen atom, and the other an equatorial position. An inner-sphere-coordinated methanol molecule in the equatorial plane and a solvent molecule hydrogen-bonded to the vanadyl oxygen were also identified. No evidence for the trans isomer was observed.     

原位探测防污高分子材料与液体界面的分子结构

Marine organisms such as plants, algae or small animals can adhere to surfaces of materials that are submerged in ocean. The accumulation of these organisms on surfaces is a marine biofouling process that has considerable adverse effects. Marine biofouling on ship hulls can cause severe fuel consumption increase. Investigations on antifouling polymers are therefore becoming important research topics for marine vessel operations. Antifouling polymers can be applied as coating layers on the ship hull, protecting it against the settlement and growth of sea organisms. Polyethylene glycol (PEG) is a hydrophilic polymer that can effectively resist the accumulation of marine organisms. PEG-based antifouling coatings have therefore been extensively researched and developed. However, the inferior stability of PEG makes it subject to degradation, rendering it ineffective for long-term services. Zwitterionic polymers have also emerged as promising antifouling materials in recent years. These polymers consist of both positively charged and negatively charged functional groups. Various zwitterionic polymers have been demonstrated to exhibit exceptional antifouling properties. Previously, surface characterizations of zwitterionic polymers have revealed that strong surface hydration is critical for their antifouling properties. In addition to these hydrophilic polymers, amphiphilic materials have also been developed as potential antifouling coatings. Both hydrophobic and hydrophilic functional groups are incorporated into the backbones or sidechains of these polymers. It has been demonstrated that the antifouling performance can be enhanced by precisely controlling the sequence of the hydrophobic-hydrophilic functionalities. Since biofouling generally occurs at the outer surface of the coatings, the antifouling properties of these coatings are closely related to their surface characteristics in water. Therefore, understanding of the surface molecular structures of antifouling materials is imperative for their future developments. In this review, we will summarize our recent advancements of antifouling material surface analysis using sum frequency generation (SFG) vibrational spectroscopy. SFG is a surface-sensitive technique which can provide molecular information of water and polymer structures at interfaces in situ in real time. The antifouling polymers we will review include zwitterionic polymer brushes, mixed charged polymers, and amphiphilic polypeptoids. Interfacial hydration studies of these polymers by SFG will be presented. The salt effect on antifouling polymer surface hydration will also be discussed. In addition, the interactions between antifouling materials and protein molecules as well as algae will be reviewed. The above research clearly established strong correlations between strong surface hydration and good antifouling properties. It also demonstrated that SFG is a powerful technique to provide molecular level understanding of polymer antifouling mechanisms.     

N(2)O(5) reaction on submicron sea salt aerosol: kinetics, products, and the effect of surface active organics

The reaction of N(2)O(5) on sea salt aerosol is a sink for atmospheric nitrogen oxides and a source of the Cl radical. We present room-temperature measurements of the N(2)O(5) loss rate on submicron artificial seawater (ASW) aerosol, performed with an entrained aerosol flow tube coupled to a chemical ionization mass spectrometer, as a function of aerosol phase (aqueous or partially crystalline), liquid water content, and size. We also present an analysis of the product growth kinetics showing that ClNO(2) is produced at a rate equal to N(2)O(5) loss, with an estimated lower limit yield of 50% at 50% relative humidity (RH). The reaction probability for N(2)O(5), gamma(N(2)(O)(5)), depends strongly on the particle phase, being 0.005 +/- 0.004 on partially crystalline ASW aerosol at 30% RH and 0.03 +/- 0.008 on aqueous ASW aerosol at 65% RH. At 50% RH, N(2)O(5) loss is relatively insensitive to particle size for radii greater than 100 nm, and gamma(N(2)(O)(5)) displays a statistically insignificant increase from 0.022 to approximately 0.03 for aqueous ASW aerosol over the RH range of 43-70%. We find that the presence of millimolar levels of hexanoic acid in the aerosol bulk decreases the gamma(N(2)(O)(5)) at 70% RH by a factor of 3-4 from approximately 0.025 to 0.008 +/- 0.004. This reduction is likely due to the partitioning of hexanoic acid to the gas-aerosol interface at a surface coverage that we estimate to be equivalent to a monolayer. This result is the first evidence that a monolayer coating of aqueous organic surfactant can slow the reactive uptake of atmospheric trace gases to aerosol.     

Synthesis, crystal structure, spectral studies, and catechol oxidase activity of trigonal bipyramidal Cu(II) complexes derived from a tetradentate diamide bisbenzimidazole ligand

A new benzimidazole-based diamide ligand-N,N'-bis(glycine-2- benzimidazolyl)hexanediamide (GBHA)-has been synthesized and utilized to prepare Cu(II) complexes of general composition [Cu(GBHA)X]X, where X is an exogenous anionic ligand (X = Cl(-), NO(3)(-), SCN(-)). The X-ray structure of one of the complexes, [Cu(GBHA)Cl]Cl.H(2)O.CH(3)OH, has been obtained. The compound crystallizes in the monoclinic space group C2/c with unit cell dimensions a = 26.464(3) A, b = 10.2210(8) A, c = 20.444(2) A, alpha = 90 degrees, beta = 106.554(7) degrees, gamma = 90 degrees, V= 5300.7(9) A(3), and Z = 8. To the best of our knowledge, the [Cu(GBHA)Cl]Cl.H(2)O.CH(3)OH complex is the first structurally characterized mononuclear trigonal bipyramidal copper(II) bisbenzimidazole diamide complex having coordinated amide carbonyl oxygen. The coordination geometry around the Cu(II) ion is distorted trigonal bipyramidal (tau = 0.59). Two carbonyl oxygen atoms and a chlorine atom form the equatorial plane, while the two benzimidazole imine nitrogen atoms occupy the axial positions. The geometry of the Cu(II) center in the solid state is not preserved in DMSO solution, changing to square pyramidal, as suggested by the low-temperature EPR data g( parallel) > g( perpendicular) > 2.0023. All the complexes display a quasi-reversible redox wave due to the Cu(II)/Cu(I) reduction process. E(1/2) values shift anodically from Cl(-) < NO(3)(-) < SCN(-), indicating that the bound Cl(-) ion stabilizes the Cu(II) ion while the N-bonded SCN(-) ion destabilizes the Cu(II) state in the complex. When calculated against NHE, the redox potentials turn out to be quite positive as compared to other copper(II) benzimidazole bound complexes (Nakao, Y.; Onoda, M.; Sakurai, T.; Nakahara, A.; Kinoshita, L.; Ooi, S. Inorg. Chim. Acta 1988, 151, 55. Addison, A. W.; Hendricks, H. M. J.; Reedijk, J.; Thompson, L. K. Inorg. Chem. 1981, 20 (1), 103. Sivagnanam, U.; Palaniandavar, M. J. Chem. Soc., Dalton Trans. 1994, 2277. Palaniandavar, M.; Pandiyan, T.; Laxminarayan, M.; Manohar, H. J. Chem. Soc., Dalton Trans. 1995, 457. Sakurai, T.; Oi, H.; Nakahara, A. Inorg. Chim. Acta 1984, 92, 131). It is therefore concluded that binding of amide carbonyl oxygen destabilizes the Cu(II) state. The complex [Cu(II)(GBHA)(NO(3))](NO(3)) could be successfully reduced by the addition of dihydroxybenzenes to the corresponding [Cu(I)(GBHA)](NO(3)). (1)H NMR of the reduced complex shows slightly broadened and shifted (1)H signals. The reduction of the Cu(II) complex presumably occurs with the corresponding 2e(-) oxidation of the quinol to quinone. Such a conversion is reminiscent of the functioning of a copper-containing catechol oxidase from sweet potatoes and the met form of the enzyme tyrosinase.     

海洋污损生物粘附机制及防污涂层表面工程

任何浸入海水的结构物均会受到海洋污损生物的附着。 在物体表面涂覆防污涂料是最广泛的防污方式,无毒污损脱附型防污涂料已成为当前的研究热点。 分析了污损生物的粘附过程及界面粘结作用,探讨了表面能、涂层模量、表面化学成分、微观形貌、颜色等因素对涂层防污效果的影响,并指出涂料工程化中必须解决的问题。     

Antifouling properties of poly(methyl methacrylate) films grafted with poly(ethylene glycol) monoacrylate immersed in seawater

Biofouling of all structures immersed in seawater constitutes an important problem, and many strategies are currently being developed to tackle it. In this context, our previous work shows that poly(ethylene glycol) monoacrylate (PEGA) macromonomer grafted on preoxidized poly(methyl methacrylate) (PMMAox) films exhibits an excellent repellency against the bovine serum albumin used as a model protein. This study aims to evaluate the following: (1) the prevention of a marine extract material adsorption by the modified surfaces and (2) the antifouling property of the PEGA-g-PMMAox substrates when immersed in natural seawater during two seasons (season 1: end of April-beginning of May 2007, and season 2: end of October-beginning of November 2007). The antifouling performances of the PEGA-g-PMMAox films are investigated for different PEG chain lengths and macromonomer concentrations into the PEGA-based coatings. These two parameters are followed as a function of the immersion time, which evolves up to 14 days. The influence of the PEGA layer on marine compounds (proteins and phospholipids) adsorption is evidenced by time-of-flight secondary ion mass spectrometry (ToF-SIMS) and X-ray photoelectron spectroscopy (XPS). It was found that the antifouling efficiency of the PEGA-grafted surfaces increases with both PEGA concentration and PEG chain length.