碳包裹纳米（fe，ni）粒子的制备与磁性

采用D113离子交换树脂与Ni2 、Fe2 交换后形成含金属的Fe-Ni/D113前驱体,经热解制备碳包裹纳米FeNi合金粒子。TG分析表明,Fe-Ni/D113的热稳定性要强于D113。XRD、TEM测试结果表明,在400、500、600和700℃热解Fe-Ni/D113均可获得碳包裹纳米FeNi合金粒子,而且纳米FeNi合金粒子的粒径随热解温度的升高而增大。室温磁性能测试结果表明,400℃热解产物具有超顺磁特性,500、600和700℃热解产物的矫顽力Hc均远大于相应的块体金属,并与产物中纳米FeNi合金粒子的尺寸有关;所有热解产物比饱和磁化强度Ms小于相应的块体材料,并随其中纳米合金粒子尺寸的增大而增加。     

Fe-Ni/C复合纳米纤维的原位制备与微波吸收性能

采用静电纺丝技术结合稳定化和碳化处理原位制备了Fe-Ni/C复合纳米纤维, 其平均直径约为215 nm, 所生成的Fe-Ni合金纳米颗粒较均匀地分布在碳基纳米纤维的内部和表面, 且被石墨化碳层所包覆. 以Fe-Ni/C复合纳米纤维为吸收剂、 硅橡胶为基质制备成吸波涂层, 研究了碳化温度对电磁特性和微波吸收性能的影响. 结果表明, 涂层厚度为1.2~2.0 mm、 Fe-Ni/C复合纳米纤维质量分数为5%的吸波涂层表现出优良的微波吸收性能, 在7.4~18 GHz频率范围内的反射损耗均低于-20 dB; 随着复合纳米纤维的碳化温度由800 ℃升高到1200 ℃, 由于阻抗匹配特性的改善, 吸波涂层的微波吸收能力逐步加强, 其最小反射损耗由-22.6 dB降低到-63.0 dB.     

有机改性对掺Dy3+铁氧体纳米磁颗粒性能的影响

采用共沉淀-相转化法制备出纳米级掺Dy3+铁氧体磁颗粒。选择阴离子表面活性剂月桂酸、月桂酸钠、十二烷基硫酸钠对磁颗粒进行了在线表面改性,得到磁性能和表面性能不同的复合纳米磁性材料,研究了活性剂及其用量对产物构建成分、相结构、磁性能的影响。TEM图片显示磁颗粒的形貌多数为类球形,平均粒径约18 nm;XRD图谱分析发现,活性剂及其用量不同,得到的产物其构建成分、相结构也不同;VSM测试结果表明,用月桂酸改性的产物磁性能最优、十二烷基硫酸钠改性者磁性能最差,产物室温下的饱和磁化强度(MS)随活性剂用量的增大呈现出降低的变化规律。     

镍钴锌纳米铁氧体的制备及磁热性能

以乙酰丙酮盐为前驱体,三乙二醇为溶剂,采用多元醇法制备了纳米Ni0.5-xCoxZn0.5Fe2O4(x=0,0.1,0.2,0.3和0.4)铁氧体.通过X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶变换红外光谱仪(FTIR)和振动样品磁强计(VSM)等对样品的结构、形貌和磁性能进行了表征.结果表明,所得纳米Ni0.5-xCoxZn0.5Fe2O4铁氧体的分散性较好,尺寸均一.在室温下产物的剩磁和矫顽力均较小,表现出亚铁磁性.纳米Ni0.3Co0.2Zn0.5Fe2O4铁氧体的饱和磁化强度达到41.34 A·m2·kg-1,其在交变磁场中升温可达到55℃,表现出较好的磁热性能.     

Zn(0.6Mn0.2Ni0.2Fe2O4/聚邻甲基苯胺复合物的制备和电磁性能

用化学沉淀法和原位聚合法分别制备了Zn0.6Mn0.2Ni0.2Fe2O4铁氧体纳米粒子和Zn0.6Mn0.2Ni0.2Fe2O4铁氧体/聚邻甲基苯胺复合微粒(ZMNF/POT).通过现代测试技术表征了样品组成、结构、形貌和电-磁性能.结果表明,POT对ZMNF粒子具有较好的包覆作用;复合物电导率与POT的含量成正比,而磁性能与ZMNF粒子的含量相关;在1～15MHz频段内,POT和ZMNF/POT复合物的介电损耗与其电导率表现出一致性;复合物具有可观的磁损耗,比磁介质型ZMNF的大,且ZMNF含量为31.74 wt%的复合物的磁损耗最大,有望作为屏蔽和吸收电磁波材料获得应用.     

纳米Ni/SiO2介孔复合体的制备与超顺磁性

采用溶胶—凝胶法制备了含Ni2+的SiO2干凝胶,再通过化学还原得到了纳米Ni/SiO2介孔复合体。从样品的透射电子显微镜观测结果可估算出,介孔复合体中Ni粒子的尺寸约为11～12 nm。样品的磁性测量结果表明,与通常的Ni纳米颗粒相比,纳米Ni/SiO2介孔复合体中纳米Ni粒子的粒径在大于理论计算的纳米Ni粒子的临界尺寸时,仍能够保持超顺磁状态。在一定温度范围内,提高还原温度有利于复合体中纳米Ni粒子向超顺磁状态转变。     

水热法制备超顺磁性铁氧体纳米微粒

本文通过水热法制备了一系列铁氧体纳米微粒(MFe₂O₄,M=Zn,Ni,Co,Cu,Mn),用XRD和TEM对产品进行了表征,产物为纯相、粒径均匀、团聚少的纳米粒子。磁性质测量表明它们具有超顺磁性质。另外,我们还对反应过程中溶液pH值对最终产物的影响进行了研究。     

La-Co共掺杂的M型锶铁氧体纳米纤维的制备和磁性能

以聚乙烯吡咯烷酮(PVP)和金属盐为原料,采用静电纺丝、溶胶-凝胶技术以及随后的热处理工艺,制备了La、Co共掺杂的M型锶铁氧体Sr1-xLaxFe12-xCoxO19(x=0.12)(SLFC)纳米纤维.利用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和超导量子干涉仪(SQUID)技术对纳米纤维样品的结构、形貌和磁学性能进行了观测,系统地研究了不同温度下样品的磁性能变化.结果表明:经过950°C焙烧2h后,得到纯相的M型锶铁氧体纳米纤维,纤维呈竹节状结构,直径约55nm;室温下测得矫顽力(Hc)为498.53kA·m-1,饱和磁化强度(Ms)为70.76A·m2·kg-1,剩磁(Mr)为36.35A·m2·kg-1,这比未掺杂SrFe12O19(SF)时纳米纤维的磁性能有明显的改善,并且与在相同温度下制得的相应纳米粉体样品相比,磁性能明显提高.     

聚丙烯酸酯-LiNi铁氧体纳米复合物的制备和磁性研究

用流变相法制备了LiNi铁氧体纳米粒子, 通过硅烷偶联剂对纳米LiNi铁氧体表面改性, 用乳液聚合法制备了纳米LiNi铁氧体-聚丙烯酸酯复合物. 用X射线衍射(XRD)、红外光谱(IR)、透射电镜(TEM)、热重分析(TGA)、振动样品磁强计(VSM)以及阻抗-材料分析仪等表征了样品的结构、形貌和磁性能. 结果表明, 引入的纳米铁氧体被聚丙烯酸酯分子链所包覆, 明显提高了复合物的热稳定性. 在外加磁场下, 复合物表现出了较弱的亚铁磁性, 并具有一定的磁滞损耗特性.     

镝掺杂铁氧体纳米晶的制备、表征和磁性

采用化学共沉淀法制备出了镝掺杂铁氧体纳米晶, 利用透射电子显微镜(TEM)、X射线衍射仪(XRD)、傅立叶红外光谱仪(FTIR)、古埃磁天平、振动样品磁强计(VSM)、X射线能谱仪(EDX)等仪器对产物进行了表征, 研究了Dy^3＋掺杂量对铁氧体纳米晶的结构、磁性和粒度的影响. 结果表明: 适量稀土元素镝离子的掺杂可以提高尖晶石型铁氧体的磁性、降低矫顽力, 当n(Fe^3＋)∶n(Dy^3＋)＝14∶1时其磁性最强. Dy^3＋替代或充填进入了尖晶石晶格, 且主要占据B位. 掺杂了镝的铁氧体磁性纳米粒子粒度变小, 且分布更集中、均匀, 当Dy^3＋加入量为n(Fe^3＋)∶n(Dy^3＋)＝14∶1时铁氧体纳米粒子的平均粒径由掺杂前的14 nm降低到到8 nm. 这种具有超顺磁性的软磁铁氧体纳米晶可应用于纳米磁液领域.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.