Liquid phase adsorption of Congo red dye on functionalized corn cobs

This study investigates the adsorption of Congo red (CR) dye onto corn cob based activated carbon (CCAC) in the batch process. The activated carbon was characterized using FTIR, SEM, and EDX techniques, respectively. The effect of operational parameters such as the initial dye concentration (10–50?mg/L), contact time (5–160 minutes), and solution temperature (30–50°C) were studied. The amount of the CR dye adsorbed was found to increase as these operational parameters increased. Kinetic data for CR dye adsorption onto CCAC were best represented by the pseudo second-order kinetic model. Four different isotherms namely Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models were used to test the adsorption data. It fitted the Langmuir isotherm model most. Thermodynamic parameters such as ΔH⁰, ΔS⁰, and ΔG⁰ were evaluated. The adsorption process was found to be exothermic and spontaneous. The study shows that CCAC is an effective adsorbent for the adsorption of CR dye from aqueous solution.     

Efficient removal of MB dye using litchi leaves powder adsorbent: Isotherm and kinetic studies

Removal of Methylene Blue (MB) dye using Litchi Leaves Powder (LLP) material was carried out in batch mode. Effect of the mass of the adsorbent (0.1–2.5 g/L), pH of the solution (2−12), starting concentration of MB dye (50–150 mg/L), ionic strength using NaCl (0.1–0.5 M) as an electrolyte, contact time (0–60 min) on the adsorption of MB dye was studied. To calculate pH at which LLP material surface becomes neutral point of zero charge (pH_pzc) is also determined and found to be 6.48. Removal process best fit in the pseudo-second-order kinetic model as indicated by its higher R² value (0.999). Isotherm models (Freundlich and Langmuir) were fitted to the data obtained from the experiment to understand the adsorption behaviour. Result shows that experimental data were fitted to the both isotherm models (Freundlich and Langmuir) as indicated by higher R² value for both Freundlich (0.991) and Langmuir (0.994) model, and it was determined that LLP has a maximum adsorption capacity of 119.76 mg/g.     

Synthesis and characterization of antibacterial chromium iron oxide nanoparticle‐loaded activated carbon for ultrasound‐assisted wastewater treatment

The aim of this study was to evaluate the surface adsorption capacity of CrFeO₃ nanoparticle‐loaded activated carbon (CrFeO₃‐NPs–AC) for the removal of a cationic dye (methyl violet, MV). CrFeO₃‐NPs were hydrothermally synthesized and loaded on AC followed by characterization using X‐ray diffraction, field‐emission scanning electron microscopy and energy‐dispersive and Fourier transform infrared spectroscopies. The CrFeO₃‐NPs were tested for in vitro antibacterial activities against Gram‐positive (Staphylococcus aureus) and Gram‐negative (Pseudomonas aeruginosa) bacteria. Minimum inhibitory and minimum bactericidal concentrations of CrFeO₃‐NPs–AC were obtained to be 50 and 100 μg ml^?1, respectively, against S. aureus and 25 and 50 μg ml^?1 against P. aeruginosa. These results indicated the antibacterial properties of CrFeO₃‐NPs–AC. To investigate the adsorption process, several systematic experiments were designed by varying parameters such as adsorbent mass, pH, initial MV concentration and sonication time. The adsorption process was modelled and the optimal conditions were determined to be 0.013 g, 7.4, 15 mg l^?1 and 8 min for adsorbent mass, pH, MV concentration and sonication time, respectively. The real experimental data were found to be efficiently explained by response surface methodology and genetic algorithm model. Kinetic studies for MV adsorption showed rapid sorption dynamics described by a second‐order kinetic model, suggesting a chemisorption mechanism. Then, the experimental equilibrium data obtained at various concentrations of MV and adsorbent masses were fitted to conventional Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models. Dye adsorption equilibrium data were fitted well to the Langmuir isotherm. From the Langmuir model, the maximum monolayer capacity was calculated to be 65.67 mg g^?1 at optimum adsorbent mass.     

Isolation of Natural Colorants from Lagerstroemia indica:Kinetic and Adsorption Studies

The color components extracted and isolated from the fruits of Lagerstroemia indica were characterized by NMR, mass, IR and UV/visible spectral techniques. The bio‐colorants isolated were found to be quercetin and apigenin. The dyed samples exhibited good colour fastness to washing and perspiration. CIE Lab values have also been evaluated. The rate of dyeing was higher at higher temperature. The thermodynamic parameters were evaluated using Arrhenius plot. The positive value of enthalpy change (ΔH^≠) indicated endothermic nature of adsorption, the high negative entropy (ΔS^≠) revealed that the color components adsorb more orderly on silk and the positive value of free energy (ΔG^≠) validated the strong affinity between adsorbent and adsorbate. Adsorption study was carried out based on the model proposed by Langmuir, Freundlich, Tempkin and Pyzhev isotherm to account for the observed results. The Freundlich isotherm was found to fit best with high regression coefficient. The colorants obtained from Lagerstroemia indica fruit could form a potential source as a dye for textile dyeing.     

Application of Nanocrystalline Iranian Diatomite in Immobilized Form for Removal of a Textile Dye

The aim of the present investigation was to immobilize nanocrystalline diatomite within calcium alginate matrix for the adsorption of Direct Red23 (DR23) in aqueous media. Scanning electron microscopy (SEM), x-ray diffraction (XRD), and Fourier transform infrared (FTIR) spectroscopy were used to characterize the samples. As a result, the adsorption process obeyed pseudo-second-order kinetic model (R² = 0.9934) and Langmuir isotherm model (R² = 0.9732) with a maximum adsorption capacity of 24.10 mg/g. The value of mean free energy (15.81 kJ/mol) demonstrated that the process has been taken place chemically. As the adsorbent dosage increased from 0.5 to 3.0 g/L, the decolorization efficiency (%) increased from 26.0 to 75.5%, respectively. Inversely, the decolorization efficiency (%) decreased from 98.0 to 29.0% with increasing initial dye concentration from 5 to 160 mg/L, respectively. The negative values obtained for Gibbs free energy (ΔG°) and positive value of enthalpy change (ΔH°) indicated spontaneous and endothermic nature of the process.     

Efficient removal of methyl violet from aqueous solution by a low-cost adsorbent—C. camphora fallen leaves powder

The adsorption property of C. camphora fallen leaves powder (CFLP) to methyl violet (MV) from aqueous solution was studied in this work. The results showed that the CFLP has considerable adsorption property to MV. The percentage adsorption reached 91% in 50?mg?L^?1 of MV solution at dosage 0.6?mg?g^?1. The adsorption kinetics for MV on the CFLP follow a pseudo-second-order pathway, and the adsorption equilibrium data can be described well by the Langmuir isotherm model compared to Freundlich isotherm model. Intra-particle diffusion is not the only rate-controlling step and combination of mechanisms was involved in the entire adsorption process for MV on the CFLP; the adsorption process is endothermic, spontaneous and random. Therefore, the CFLP can be used as low-cost adsorbent for refractory cationic organic dye in wastewater.     

Mixed phase Fe2O3/Mn3O4 magnetic nanocomposite for enhanced adsorption of methyl orange dye: Neural network modeling and response surface methodology optimization

In this research, a novel magnetic mesoporous adsorbent with mixed phase of Fe₂O₃/Mn₃O₄ nanocomposite was prepared by a facile precipitating method and characterized extensively. The prepared nanocomposite was used as adsorbent for toxic methyl orange (MO) dye removal from aqua matrix considering its high surface area (178.27 m²/g) with high saturation magnetization (23.07 emu/g). Maximum dye adsorption occurs at solution pH 2.0 and the electrostatic attraction between anionic form of MO dye molecules and the positively charged nanocomposite surface is the main driving force behind this adsorption. Response surface methodology (RSM) was used for optimizing the process variables and maximum MO removal of 97.67% is obtained at optimum experimental condition with contact time, adsorbent dose and initial MO dye concentration of 45 min, 0.87 g/l and 116 mg/l, respectively. Artificial neural network (ANN) model with optimum topology of 3–5–1 was developed for predicting the MO removal (%), which has shown higher predictive ability than RSM model. Maximum adsorption capacity of this nanocomposite was found to be 322.58 mg/g from Langmuir isotherm model. Kinetic studies reveal the applicability of second‐order kinetic model with contribution of intra‐particle diffusion in this process.     

Enhanced adsorption performance of a novel Fe‐Mn‐Zr metal oxide nanocomposite adsorbent for anionic dyes from binary dye mix: Response surface optimization and neural network modeling

A novel adsorbent, Fe‐Mn‐Zr metal oxide nanocomposite was synthesized and investigated for removal of methyl orange (MO) and eosin yellow (EY) dyes from binary dye solution. The magnetic nanocomposite has shown surface area of 143.01 m²/g and saturation magnetization of 15.29 emu/g. Optimization was carried out via response surface methodology (RSM) for optimizing process variables, and optimum dye removal of 99.26% and 99.55% were obtained for MO and EY dye, respectively with contact time 62 min, adsorbent dose 0.45 g/l, initial MO concentration 11.0 mg/l, and initial EY concentration 25.0 mg/l. A feed forward back propagation neural network model has shown better prediction ability than RSM model for predicting MO and EY dye removal (%). Adsorption process strictly follows Langmuir isotherm model, and enhanced adsorption capacities of 196.07 and 175.43 mg/g were observed for MO and EY dye, respectively due to synergistic effects of physicochemical properties of trimetal oxides. Surface adsorption and pore diffusions are the mechanisms involved in the adsorption as revealed from kinetic studies.     

Fabrication and optimization calix[8]arene-PbS nanoadsorbents for the adsorption of methylene blue: Isotherms,kinetics and thermodynamics studies

The present study aims to determine the adsorption behaviour of methylene blue (MB) dye based on calix[8]arene-modified lead sulphide (PbS) nanoadsorbents under optimal conditions. Response surface methodology (RSM) was executed to evaluate the interactive effect of three factors (adsorbent dosage, contact time, and pH) on the adsorption of MB dye using a central composite design (CCD). The optimised values for adsorbent dosage, contact time, and pH solution were found to be 45.00 mg of calix[8]arene-modified PbS, contact time of 180 min, and pH 6. This study reports the results of batch adsorption experiments, which include the adsorption capacity, kinetics, and isotherm of the MB adsorption process. Pseudo-first order and pseudo-second order were demonstrated for their quality to fit the data. Pseudo-second order was the best in fitting the adsorption data with the higher R² values (R² > 0.928), indicating chemisorption to be the mechanism of adsorption. The Langmuir and Freundlich equilibrium models were employed to determine the isotherm parameters. The equilibrium assessment illustrated that the Langmuir isotherm model fitted well with the adsorption data, and a maximum MB adsorption capacity of 11.90 mg/g was achieved. The characterisation studies with EDX, FESEM, and FTIR indicated a successful synthesis of calix[8]arene-modified PbS.     

Triclosan removal by adsorption using activated carbon derived from waste biomass: Isotherms and kinetic studies

Triclosan is an antimicrobial agent that is normally used in many personal care products such as toothpastes, shampoos, deodorants, and cosmetics and is toxic to some aquatic organisms, amphibians, and the male reproductive system. In this study, activated carbon from coconut pulp waste (Cocos nuciefera) is used to remove triclosan from aqueous solutions. Activated carbon was prepared using coconut pulp waste treated with zinc chloride and burned in a horizontal furnace with nitrogen flow at 300°C for 1 hr. The parameters studied were the contact time, adsorbent dosage, agitation, initial triclosan concentration, pH, and temperature. The characterization of the adsorbent was done by field‐emission scanning electron microscopy and Fourier transform infrared spectroscopy. The activated carbon reaches equilibrium in 20 min with a percentage removal of 80.77% and adsorbent capacity (q_e) of 2.02 mg/g. From the kinetic study, it was concluded that the adsorbent followed a pseudo‐second‐order type reaction with a correlation coefficient (R²) of .999, and q_e = 2.036 mg/g. From the isotherm study, the adsorbent was found to follow the Langmuir isotherm with a higher R² value of .9249 compared to the Freundlich and Temkin isotherms. This study proved that activated carbon derived from coconut pulp waste can be a promising low‐cost adsorbent to remove dissolved triclosan from water.     

Adsorption of Cr(VI) using activated neem leaves: kinetic studies

In the present study, adsorbent is prepared from neem leaves and used for Cr(VI) removal from aqueous solutions. Neem leaves are activated by giving heat treatment and with the use of concentrated hydrochloric acid (36.5 wt%). The activated neem leaves are further treated with 100 mmol of copper solution. Batch adsorption studies demonstrate that the adsorbent prepared from neem leaves has a significant capacity for adsorption of Cr(VI) from aqueous solution. The parameters investigated in this study include pH, contact time, initial Cr(VI) concentration and adsorbent dosage. The adsorption of Cr(VI) is found to be maximum (99%) at low values of pH in the range of 1-3. A small amount of the neem leaves adsorbent (10 g/l) could remove as much as 99% of Cr(VI) from a solution of initial concentration 50 mg/l. The adsorption process of Cr(VI) is tested with Langmuir isotherm model. Application of the Langmuir isotherm to the system yielded maximum adsorption capacity of 62.97 mg/g. The dimensionless equilibrium parameter, R _L, signifies a favorable adsorption of Cr(VI) on neem leaves adsorbent and is found to be between 0.0155 and 0.888 (0<R _L<1). The adsorption process follows second order kinetics and the corresponding rate constant is found to be 0.00137 g/(mg) (min).     

Removal of dyes from water by conducting polymeric adsorbent

Chemically synthesized conducting polyaniline (PANI) was investigated as adsorbent for its possible application in the removal of organic dyes, such as methylene blue (MB) and procion red (PR) from their aqueous solution. PANI adsorbent behaves as a charged surface upon post‐synthesis treatment of the polymer with acid and base. The adsorbent thus treated shows a high selectivity for the removal of dyes in the adsorption process. The Langmuir adsorption isotherm was used to represent the experimental adsorption data. The cationic dye, MB can be preferentially removed by the base‐treated PANI while the anionic dye, PR is predominately removed by the acid‐treated one. These observations were further evidenced from the measurements of molar conductance and pH of the dye solutions employed for adsorption. The finding can be explained considering the electrostatic nature of adsorption coupled with the morphology of the PANI surface thus treated. Copyright © 2004 John Wiley & Sons, Ltd.     

Application of Functionalized DVB-co-GMA Polymeric Microspheres in the Enhanced Sorption Process of Hazardous Dyes from Dyeing Baths

Intensive development of many industries, including textile, paper, plastic or food, generate huge amounts of wastewaters containing not only toxic dyes but also harmful auxiliaries such as salts, acid, bases, surfactants, oxidants, heavy metal ions. The search for effective pollutant adsorbents is a huge challenge for scientists. Synthesis of divinylbenzene copolymer with glycidyl methacrylate functionalized with triethylenetetramine (DVB-co-GMA-TETA) resin was performed and the obtained microspheres were evaluated as a potential adsorbent for acid dye removal from dyeing effluents. The sorption capacities were equal to 142.4 mg/g for C.I. Acid Green 16 (AG16), 172 mg/g for C.I. Acid Violet 1 (AV1) and 216.3 mg/g for C.I. Acid Red 18 (AR18). Non-linear fitting of the Freundlich isotherm to experimental data was confirmed rather than the Langmuir, Temkin and Dubinin-Radushkevich. The kinetic studies revealed that intraparticle diffusion is the rate-limiting step during dye adsorption. Auxiliaries such as Na₂SO₄ (5–25 g/L), CH₃COOH (0.25–1.5 g/L) and anionic surfactant (0.1–0.5 g/L) present in the dyeing baths enhance the dye adsorption by the resin in most cases. Regeneration of DVB-co-GMA-TETA is possible using 1 M NaCl-50% v/v CH₃OH.     

Fast Removal and Recovery of Methylene Blue by Activated Carbon Modified with Magnetic Iron Oxide Nanoparticles

A magnetic adsorbent was synthesized by modification of activated carbons with magnetic iron oxide nanoparticles (AC‐MIONs). The preparation method is fast and could be carried out in an ordinary condition. The AC‐MIONs were used as quite efficient adsorbents for separation of methylene blue (MB) from aqueous solution in a batch process. The effect of different parameters such as pH, temperature, electrolyte concentration, contact time and interfering ions on the removal of MB were studied. The adsorption data were analyzed by Langmuir and Freundlich isotherm models and a maximum adsorption amount of 47.62 mg g^‐1 and a langmuir adsorption equilibrium constant of 3.0 L mg^‐1 were obtained. The obtained results revealed that AC‐MIONs were effective adsorbents for fast removal of MB from different aqueous solutions. This adsorbent was successfully used for removal of MB from Karoon River water.     

Application of artificial neural network for comparison and modeling of the ultrasonic and stirrer assisted removal of anionic dye using activated carbon supported with nanostructure material

In this study, a green approach has been described for the synthesis of copper sulfide nanoparticles loaded on activated carbon (CuS‐NP‐AC) and usability of it for the removal of sunset yellow (SY) dye by ultrasound‐assisted and stirrer has been compared. In addition, the artificial neural network (ANN) model has been employed for a forecasting removal percentage of SY dye using the results obtained. This material was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The impact of variables, including initial dye concentration (mg/L), pH, adsorbent dosage (g), sonication time (min) and temperature (°C) on SY removal was studied. Fitting the experimental equilibrium data of different isotherm models such as Langmuir, Freundlich, Temkin and Dubinin–Radushkevich models display the suitability and applicability of the Langmuir model. Analysis of experimental adsorption data of different kinetic models including pseudo‐first and second order, Elovich and intraparticle diffusion models indicate the applicability of the second‐order equation model. The adsorbent (0.005 g) is applicable for successful removal of SY dye (> 98%) in short time (9 min) under ultrasound condition. A three layer ANN models with 8 and 6 neurons at hidden layer was selected as optimal models using stirrer and ultrasonic, respectively. These models displayed a good agreement between forecasted data and experimental data with the determination coefficient (R²) of 0.9948 and 0.9907 and mean squared error (MSE) of 0.0001 and 0.0002 for training set using stirrer and ultrasonic, respectively.     

Equilibrium and kinetic study of novel methyltrimethoxysilane magnetic titanium dioxide nanocomposite for methylene blue adsorption from aqueous media

Novel magnetic titanium dioxide nanoparticles decorated with methyltrimethoxysilane (Fe₃O₄@TiO₂‐MTMOS) were successfully fabricated via a sol–gel method at room temperature. The synthesized material was characterized using Fourier transform infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, thermogravimetric analysis and vibrating sample magnetometry. The removal efficiency of the adsorbent was evaluated through the adsorption of methylene blue (MB) dye from water samples. The adsorption isotherm and kinetics were evaluated using various models. The Langmuir model indicated a high adsorption capacity (11.5 mg g^?1) of Fe₃O₄@TiO₂‐MTMOS. The nanocomposite exhibited high removal efficiency (96%) and good regeneration (10 times) compared to Fe₃O₄ and Fe₃O₄@TiO₂ at pH = 9.0. Based on the adsorption mechanism, electrostatic interaction plays a main role in adsorption since MB dye is cationic in nature at pH = 9, whereas the adsorbent acquired an anionic nature. The newly synthesized Fe₃O₄@TiO₂‐MTMOS can be used as a promising material for efficient removal of MB dye from aqueous media.     

Adsorption of Acid Dyes from Aqueous Solutions by Calcined Alunite and Granular Activated Carbon

Dyestuff production units and dyeing units have always had a pressing need for techniques that allow economical pretreatment for color in the effluent. The effectiveness of adsorption for dye removal from wastewaters had made it an ideal alternative to other expensive treatment options. This paper deals with an investigation on alunite, existing wide reserves in Türkiye and in the world, for dye removal. Calcined alunite was utilized for this study and its performance evaluated against that of granular activated carbon (GAC). The use of calcined alunite for the removal of Acid Blue 40 and Acid Yellow 17 (AB 40 and AY 17) from aqueous solution at different calcination temperature and time, particle size, pH, agitation time and dye concentration has been investigated. The adsorption followed by Langmuir and Freundlich isotherms. The process follows first order adsorption rate expression and the rate constant was found to be 7.65 × 10^–2 and 5.74 × 10^–2 min^–1 for adsorption of AB 40 and AY 17 on calcined alunite, and 8.41 × 10^–2 and 10.04 × 10^–2 min^–1 for adsorption of AB 40 and AY 17 on GAC, respectively. The equilibrium saturation adsorption capacities were 212.8 mg dye/g calcined alunite and 151.5 mg dye/g calcined alunite for AB 40 and AY 17, respectively. The adsorption capacities were found to be 57.47 mg and 133.3 mg dye per g of GAC for AB 40 and AY 17, respectively. The results indicate that, for the removal of acid dye, calcined alunite was most effective adsorbent, although comparable dye removals were exhibited by GAC.     

Adsorption removal of methyl violet from aqueous solution by chromium phosphovanadate

An effective adsorbent for methyl violet (MV), chromium phosphovanadate (named as Cr‐PV) nanomaterials, was prepared by a simple coprecipitation strategy. The microstructure and morphology of as‐synthesized Cr‐PV were characterized by SEM, X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FTIR), respectively, which was confirmed as nanosheet shapes. The adsorption behavior for MV from aqueous solutions was systematically investigated. The kinetic and equilibrium results indicate that the adsorption process follows pseudo‐second‐order kinetic model and Langmuir isotherm, respectively. Compared with PV and commercially available activated carbon, Cr‐PV has preferable adsorption property to MV. The maximum adsorption capacity can reach 123.81 mg g^?1 at room temperature. The thermodynamic parameters such as Gibbs free energy (ΔG^ο), enthalpy (ΔH^ο), and entropy change (ΔS^ο) show that the adsorption of MV is an endothermic and spontaneous process. Moreover, the adsorptive behavior between Cr‐PV and MV is monolayer adsorption and electrostatic interaction mechanism. Cr‐PV, as a promising adsorbent with high adsorption capacity and fast adsorption rate, shows great potential for the removal of MV from wastewater.     

Adsorption of tartrazine from an aqueous solution by octadecyltrimethylammonium bromide-modified bentonite: Kinetics and isotherm modeling

A modified bentonite was prepared at different surfactant (ODTMA) loadings through ion exchange. The obtained organobentonite adsorbent materials were then used for the removal of an anionic dye, tartrazine, from an aqueous solution. The bentonite was characterized by X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis, and Brunauer- Emmett-Teller (BET) method. The modification of organophilic bentonite by ODTMA increases the basal spacing d₀₀₁ from 24.1 to 39.1 Å when the cation exchange capacity increases from 1 to 4. The increase in the spacing, due to the basic organic modifications, was confirmed by the results of thermogravimetric analysis, Fourier transform infrared spectroscopy, and BET. The effects of contact time, initial concentration, and solution pH onto an adsorbed amount of tartrazine were investigated. To predict adsorption isotherm, the experimental data were analyzed using the Langmuir and Freundlich isotherm equations. It was determined that the isotherm data were fitted to the Langmuir isotherm. The adsorption process was also found to follow a pseudo-second-order kinetic model.