Benzodicarbomethoxytetrathiafulvalene derivatives as soluble organic semiconductors

A series of new tetrathiafulvalene (TTF) derivatives bearing dimethoxycarbonyl and phenyl or phthalimidyl groups fused to the TTF core (6 and 15-18) has been synthesized as potential soluble semiconductor materials for organic field-effect transistors (OFETs). The electron-withdrawing substituents lower the energy of the HOMO and LUMO levels and increase the solubility and stability of the semiconducting material. Crystal structures of all new TTF derivatives are also described, and theoretical DFT calculations were carried out to study the potential of the crystals to be used in OFET. In the experimental study, the best performing device exhibited a hole mobility up to 7.5 × 10(-3) cm(2) V(-1) s(-1)).     

Low-bandgap poly(thiophene-phenylene-thiophene) derivatives with broaden absorption spectra for use in high-performance bulk-heterojunction polymer solar cells

Two low-bandgap (LGB) conjugated polymers ( P1 and P2) based on thiophene-phenylene-thiophene (TPT) with adequate energy levels have been designed and synthesized for application in bulk-heterojunction polymer solar cells (PSCs). The absorption spectral, electrochemical, field effect hole mobility and photovoltaic properties of LGB TPT derivatives are investigated and compared with poly(3-hexylthiophene) (P3HT). Photophysical studies reveal bandgaps of 1.76 eV for P1 and 1.70 eV for P2, which could effectively harvest broader solar spectrum. In addition, the thin film absorption coefficients of P1 and P2 are 1.6 x 10 (5) cm (-1) (lambda approximately 520 nm) and 1.4 x 10 (5) cm (-1) (lambda approximately 590 nm), respectively. Electrochemical studies indicate desirable HOMO/LUMO levels that enable a high open circuit voltage while blending them with fullerene derivatives as electron acceptors. Furthermore, both materials show sufficient hole mobility (3.4 x 10 (-3) cm (2)/Vs for P2) allowing efficient charge extraction and a good fill-factor for PSC application. High-performance power conversion efficiency (PCE) of 4.4% is obtained under simulated solar light AM 1.5 G (100 mW/cm (2)) from PSC device with an active layer containing 25 wt% P2 and 75 wt% [6,6]-phenyl-C71-butyric acid methyl ester (PC 71BM), which is superior to that of the analogous P3HT cell (3.9%) under the same experimental condition.     

D-A Copolymers Based on a Pentacyclic Acceptor Unit and a 3,3′-Difluoro-2,2′-bithiophene for Solar Cells

A D-A copolymer, P2FBTTPTI, was developed by copolymerizing a pentacyclic acceptor unit, thieno[2′,3′:5,6]pyrido[3,4-g]thieno[3,2-c]isoquinoline-5,11(4 H,10 H)-dione(TPTI), with 3,3′-difluoro-2,2′-bithiophene(2 FBT). P2 FBTTPTI possessed a low highest occupied molecular orbital(HOMO) energy level(-5.50 e V) and a good hole mobility(4.14 × 10~(-4) cm~2·V~(-1)·s~(-1)). P2FBTTPTI:PC_(71)BM solar cells gave a decent power conversion efficiency(PCE) of 7.64% and a high open-circuit voltage(V_(oc)) of 0.95 V.     

Benzobisthiazole Polymer with Resonance-assisted Hydrogen Bonds for High-performance Transistor and Solar Cell Applications

Benzobisthiazole polymer with resonance-assisted hydrogen bonds(RAHBs)has been synthesized for both organic field-effect transistor and polymer solar cell applications.The properties of the hydrogen bonded polymer are compared with the reference polymer without RAHBs.Single-crystal X-ray diffraction analyses of the building block reveal that the RAHB interactions are formed between the carbamate hydrogen and imine nitrogen of the thiazoles.The hydrogen donor and acceptor are connected byπ-conjugated molecular framework and the hydrogen-bridged quasi aromatic rings lock the conformation of the building block.The building block adopted a layered sandwich packing in crystal instead of slipped herringbone stacking which was often found in the crystal of benzobisthiazole derivatives.The polymer PCBTZ-TT with RAHBs showed deeper HOMO/LUMO energy level(about 0.2 eV)than reference polymer.The PCBTZ-TT demonstrated the hole mobility of0.96 cm²·V^-1·s^-1 in field-effect transistor devices and achieved power conversion efficiency of 13.6%in solar cell devices with Y6 as acceptor without any additive.     

Simple replication methods for producing nanoslits in thermoplastics and the transport dynamics of double-stranded DNA through these slits

Mixed-scale nano- and microfluidic networks were fabricated in thermoplastics using simple and robust methods that did not require the use of sophisticated equipment to produce the nanostructures. High-precision micromilling (HPMM) and photolithography were used to generate mixed-scale molding tools that were subsequently used for producing fluidic networks into thermoplastics such as poly(methyl methacrylate), PMMA, cyclic olefin copolymer, COC, and polycarbonate, PC. Nanoslit arrays were imprinted into the polymer using a nanoimprinting tool, which was composed of an optical mask with patterns that were 2-7 μm in width and a depth defined by the Cr layer (100 nm), which was deposited onto glass. The device also contained a microchannel network that was hot embossed into the polymer substrate using a metal molding tool prepared via HPMM. The mixed-scale device could also be used as a master to produce a polymer stamp, which was made from polydimethylsiloxane, PDMS, and used to generate the mixed-scale fluidic network in a single step. Thermal fusion bonding of the cover plate to the substrate at a temperature below their respective T(g) was accomplished by oxygen plasma treatment of both the substrate and cover plate, which significantly reduced thermally induced structural deformation during assembly: ～6% for PMMA and ～9% for COC nanoslits. The electrokinetic transport properties of double-stranded DNA (dsDNA) through the polymeric nanoslits (PMMA and COC) were carried out. In these polymer devices, the dsDNA demonstrated a field-dependent electrophoretic mobility with intermittent transport dynamics. DNA mobilities were found to be 8.2 ± 0.7 × 10(-4) cm(2) V(-1) s(-1) and 7.6 ± 0.6 × 10(-4) cm(2) V(-1) s(-1) for PMMA and COC, respectively, at a field strength of 25 V cm(-1). The extension factors for λ-DNA were 0.46 in PMMA and 0.53 in COC for the nanoslits (2-6% standard deviation).     

Synthesis and characterization of a thiazolo[5,4-d]thiazole-based copolymer for high performance polymer solar cells

A highly processable, new semiconducting polymer, PCDTTz, based on alternating thiazolothiazole and carbazole units was synthesized. The new polymer exhibited a field-effect carrier mobility of up to 3.8 × 10(-3) cm(2) V(-1) s(-1) and bulk heterojunction solar cells made from PCDTTz produced a power conversion efficiency of 4.88% under AM 1.5 G (100 mW cm(-2)) conditions.     

Siloxane-terminated solubilizing side chains: bringing conjugated polymer backbones closer and boosting hole mobilities in thin-film transistors

We introduce a novel siloxane-terminated solubilizing group and demonstrate its effectiveness as a side chain in an isoindigo-based conjugated polymer. An average hole mobility of 2.00 cm(2) V(-1) s(-1) (with a maximum mobility of 2.48 cm(2) V(-1) s(-1)), was obtained from solution-processed thin-film transistors, one of the highest mobilities reported to date. In contrast, the reference polymer with a branched alkyl side chain gave an average hole mobility of 0.30 cm(2) V(-1) s(-1) and a maximum mobility of 0.57 cm(2) V(-1) s(-1). This is largely explained by the polymer packing: our new polymer exhibited a π-π stacking distance of 3.58 ?, while the reference polymer showed a distance of 3.76 ?.     

High performance low band gap polymer solar cells with a non-conventional acceptor

A novel C70 fullerene derivative was designed and synthesized by [4+2] cyclic addition reaction between indene derivative (methyl 1H-indene-3-carboxylate) and C70. The absorption and photoluminescence of H120 and its mixed films with different polymer donor materials were investigated, as well as its electrochemical property and electron mobility. It was found that H120 has 0.05 eV higher LUMO level than that of PC(70)BM. Its electron mobility reached 6.32 × 10(-4) cm(2) V(-1) s(-1), which is slightly lower than 9.55 × 10(-4) cm(2) V(-1) s(-1) of PC(70)BM. The photovoltaic devices based on P3HT, and two high efficiency low band gap polymers, PBDTTT-C and PBDTTDPP as donors, with H120 as an acceptor gave power conversion efficiencies of 4.2%, 6.0% and 6.2%, respectively.     

Bis(methylthio)tetracenes: synthesis, crystal-packing structures, and OFET properties

5,12-Bis(methylthio)tetracene (2) and 5,11-bis(methylthio)tetracene (3) were synthesized. DFT calculations indicate that the HOMO and LUMO energy levels of 2 and 3 are lowered by 0.13-0.24 eV and their HOMO-LUMO energy gaps are reduced by 0.1 eV relative to those of tetracene. X-ray crystallographic data revealed that 2 is arranged as a result of a 1-D slipped-cofacial π-stacking with S-S and S-π interactions, similar to the packing arrangement of 6,13-bis(methylthio)pentacene (1), whereas 3 exhibits a herringbone packing arrangement without S-S interactions. The OFET devices fabricated using spin-coated films of soluble 1 and 2, with a bottom-contact device configuration, exhibited hole mobilities as high as 1.3 × 10(-2) and 4.0 × 10(-2) cm(2) V(-1) s(-1) with current on/off ratios of over 10(5) and 10(4), respectively.     

Side-chain engineering of high-efficiency conjugated polymer photovoltaic materials

In recent years,conjugated polymers have attracted great attention in the application as photovoltaic donor materials in polymer solar cells(PSCs).Broad absorption,lower-energy bandgap,higher hole mobility,relatively lower HOMO energy levels,and higher solubility are important for the conjugated polymer donor materials to achieve high photovoltaic performance.Side-chain engineering plays a very important role in optimizing the physicochemical properties of the conjugated polymers.In this article,we review recent progress on the side-chain engineering of conjugated polymer donor materials,including the optimization of flexible side-chains for balancing solubility and intermolecular packing(aggregation),electron-withdrawing substituents for lowering HOMO energy levels,and two-dimension(2D)-conjugated polymers with conjugated side-chains for broadening absorption and enhancing hole mobility.After the molecular structural optimization by side-chain engineering,the2D-conjugated polymers based on benzodithiophene units demonstrated the best photovoltaic performance,with powerconversion efficiency higher than 9%.     

Effect of branched conjugation structure on the optical, electrochemical, hole mobility, and photovoltaic properties of polythiophenes

Four branched polythiophenes (PTs) with different ratios of conjugated terthiophene-vinylene side chains, PT-TThV10 to PT-TThV40, were synthesized by Stille coupling reaction. The polymers exhibited reversible p-doping/dedoping (oxidation/re-reduction) and n-doping/dedoping (reduction/reoxidation) processes. The absorption spectra, hole mobility, and photovoltaic properties of the polymers were much improved in comparison with the PT derivative without the terthiophene-vinylene side chain and were influenced by the content of the conjugated side chains. With the increase of the content of the conjugated side chains, the absorption peak of the branched PTs enhanced and blue-shifted. The maximum hole mobility reached 6.35 x 10(-4) cm2/V.s (SCLC method) and the maximum power conversion efficiency of the polymer solar cell reached 1.91% under the illumination of AM 1.5, 100 mW/cm2, for the polymer with 20% terthiophene-vinylene side chains. The results indicate that the branched PTs with suitable content of the terthiophene-vinylene side chains could be promising photovoltaic materials.     

Thieno[3,2-b]thiophene-diketopyrrolopyrrole-containing polymers for high-performance organic field-effect transistors and organic photovoltaic devices

We report the synthesis and polymerization of a novel thieno[3,2-b]thiophene-diketopyrrolopyrrole-based monomer. Copolymerization with thiophene afforded a polymer with a maximum hole mobility of 1.95 cm(2) V(-1) s(-1), which is the highest mobility from a polymer-based OFET reported to date. Bulk-heterojunction solar cells comprising this polymer and PC(71)BM gave a power conversion efficiency of 5.4%.     

Bithiophene-imide-based polymeric semiconductors for field-effect transistors: synthesis, structure-property correlations, charge carrier polarity, and device stability

Developing new high-mobility polymeric semiconductors with good processability and excellent device environmental stability is essential for organic electronics. We report the synthesis, characterization, manipulation of charge carrier polarity, and device air stability of a new series of bithiophene-imide (BTI)-based polymers for organic field-effect transistors (OFETs). By increasing the conjugation length of the donor comonomer unit from monothiophene (P1) to bithiophene (P2) to tetrathiophene (P3), the electron transport capacity decreases while the hole transport capacity increases. Compared to the BTI homopolymer P(BTimR) having an electron mobility of 10(-2) cm(2) V(-1) s(-1), copolymer P1 is ambipolar with balanced hole and electron mobilities of ～10(-4) cm(2) V(-1) s(-1), while P2 and P3 exhibit hole mobilities of ～10(-3) and ～10(-2) cm(2) V(-1) s(-1), respectively. The influence of P(BTimR) homopolymer M(n) on film morphology and device performance was also investigated. The high M(n) batch P(BTimR)-H affords more crystalline film microstructures; hence, 3× increased electron mobility (0.038 cm(2) V(-1) s(-1)) over the low M(n) one P(BTimR)-L (0.011 cm(2) V(-1) s(-1)). In a top-gate/bottom-contact OFET architecture, P(BTimR)-H achieves a high electron mobility of 0.14 cm(2) V(-1) s(-1), only slightly lower than that of state-of-the-art n-type polymer semiconductors. However, the high-lying P(BTimR)-H LUMO results in minimal electron transport on exposure to ambient. Copolymer P3 exhibits a hole mobility approaching 0.1 cm(2) V(-1) s(-1) in top-gate OFETs, comparable to or slightly lower than current state-of-the-art p-type polymer semiconductors (0.1-0.6 cm(2) V(-1) s(-1)). Although BTI building block incorporation does not enable air-stable n-type OFET performance for P(BTimR) or P1, it significantly increases the OFET air stability for p-type P2 and P3. Bottom-gate/top-contact and top-gate/bottom-contact P2 and P3 OFETs exhibit excellent stability in the ambient. Thus, P2 and P3 OFET hole mobilities are almost unchanged after 200 days under ambient, which is attributed to their low-lying HOMOs (>0.2 eV lower than that of P3HT), induced by the strong BTI electron-withdrawing capacity. Complementary inverters were fabricated by inkjet patterning of P(BTimR)-H (n-type) and P3b (p-type).     

Low band gap thiophene-perylene diimide systems with tunable charge transport properties

Perylenediimide-pentathiophene systems with varied architecture of thiophene units were synthesized. The photophysical, electrochemical, and charge transport behavior of the synthesized compounds were studied. Both molecules showed a low band gap of ～1.4 eV. Surprisingly, the molecule with pentathiophene attached via β-position to the PDI unit upon annealing showed a predominant hole mobility of 1 × 10(-4) cm(2) V(-1) s(-1) whereas the compound with branched pentathiophene attached via β-position showed an electron mobility of 9.8 × 10(-7) cm(2) V(-1) s(-1). This suggests that charge transport properties can be tuned by simply varying the architecture of pentathiophene units.     

Photoconductive liquid-crystalline derivatives of 6-oxoverdazyl

1,3,5-Triphenyl-6-oxoverdazyl radicals 1[n], in which each phenyl group is substituted with three alkylsulfanyl groups (n = 6, 8, 10), exhibit a monotropic columnar rectangular (Col(r)) phase below 60 °C. Detailed analysis of 1[n] revealed a broad absorption band in the visible region with maxima at 540 and 610 nm and redox potentials E(1/2)(0/+1) = +0.99 V and E(1/2)(0/-1) = -0.45 V vs SCE. Photovoltaic studies of 1[8] demonstrated a hole mobility of 1.52 × 10?3 cm2 V?1 s?1 in the mesophase with an activation energy of 0.06 ± 0.01 eV. Magnetization studies of 1[8] revealed nearly ideal paramagnetic behavior in either the solid or fluid phase above 200 K and weak antiferromagnetic interactions at low temperatures.     

Toward a rational design of poly(2,7-carbazole) derivatives for solar cells

On the basis of theoretical models and calculations, several alternating polymeric structures have been investigated to develop optimized poly(2,7-carbazole) derivatives for solar cell applications. Selected low band gap alternating copolymers have been obtained via a Suzuki coupling reaction. A good correlation between DFT theoretical calculations performed on model compounds and the experimental HOMO, LUMO, and band gap energies of the corresponding polymers has been obtained. This study reveals that the alternating copolymer HOMO energy level is mainly fixed by the carbazole moiety, whereas the LUMO energy level is mainly related to the nature of the electron-withdrawing comonomer. However, solar cell performances are not solely driven by the energy levels of the materials. Clearly, the molecular weight and the overall organization of the polymers are other important key parameters to consider when developing new polymers for solar cells. Preliminary measurements have revealed hole mobilities of about 1 x 10(-3) cm2 x V(-1) x s(-1) and a power conversion efficiency (PCE) up to 3.6%. Further improvements are anticipated through a rational design of new symmetric low band gap poly(2,7-carbazole) derivatives.     

Hole transport in triphenylamine based OLED devices: from theoretical modeling to properties prediction

For the series of para-substituted triphenylamines, optimized geometries, HOMO and LUMO energy levels, ionization potentials Ip, reorganization energies for hole transport λ(+), and frontier orbital contours have been calculated by means of ab initio computations. Relationships between them and the Hammett parameter are presented. According to calculations, electron releasing substituents increase the HOMO and LUMO energies of TPA, while electron withdrawing ones decrease it. This behavior is reflected in subsequent decreasing and increasing of ionization potentials of substituted TPAs. Calculations show that there exists also a strong substituent effect on the reorganization energy λ(+), which is a dominating factor of hole mobility. It is concluded that proper tuning of the HOMO and LUMO levels (and, as a result, ionization potential, Ip) and reorganization energy λ(+) (consequently, hole mobility) of the triphenylamine can be done by alteration of the TPA electronic structure by an appropriate substitution. It is demonstrated that the proper adjustment of the HOMO levels of HTM facilitates the reduction of an energy barrier at the interface of ITO/HTL and HTL/EL and ensure the high hole injection and hole transport rate. On the other hand, appropriate adjustment of the LUMO level prevents an electron leak from the EL into the HTM layer. Results of these calculations can be useful in the process of designing new HTM materials of desired properties (high efficiency, stability, and durability).     

A structurally ordered thiophene-thiazole copolymer for organic thin-film transistors

This paper reports a new donor-acceptor copolymer semiconductor, PTBTh, comprising bithiophene and bithiazole where the regular coplanar structure and the intramolecular charge transfer are expected to increase the opportunity for --- stacking and charge transport. The AFM image shows lamellar stacking of the polymer on the surface. The field-effect transistor (FET) properties of PTBTh have been evaluated by a bottom-contact/bottom-gate TFT configuration. The device showed a high hole mobility of 1.14×10-2 cm2 V-1 s-1 and a current on/off ratio of 3×105 with the polymer thin film annealed at a mild temperature of 120 ℃ when measured under ambient conditions.     

Air-stable n-type organic field-effect transistors based on solution-processable, electronegative oligomers containing dicyanomethylene-substituted cyclopenta[b]thiophene

Solution-processable, electronegative, π-conjugated systems containing dicyanomethylene-substituted cyclopenta[b]thiophene were synthesized as potential active materials for air-stable n-type organic field-effect transistors (OFETs). Electrochemical measurements revealed that these compounds exhibited electrochemical stability and that the lowest unoccupied molecular orbital (LUMO) had an energy level less than -4.0 eV. Flash-photolysis time-resolved microwave conductivity (FP-TRMC) measurements were performed, and the value of intradomain electron mobility was determined to be as high as 0.1 cm(2) V(-1) s(-1) . The OFETs were fabricated by spin-coating thin films of the compounds as an active layer. The electron mobility of the OFETs was 3.5×10(-3) cm(2) V(-1) s(-1) in vacuum. Furthermore, electron mobility of the same order of magnitude and stable characteristics were obtained under air-exposed conditions. X-ray diffraction measurements of the spin-coated thin films revealed the difference of molecular arrangements depending on the inner conjugated units. Atomic force microscopy measurements of crystalline-structured films exhibited the formation of grains. The accomplishment of air-stability was attributed to the combined effect of the low-lying LUMO energy level and the molecular arrangements in the solid state, avoiding both the quenching of electron carriers and the intrusion of oxygen and/or moisture.     

High electron mobility in ladder polymer field-effect transistors

Field-effect mobility of electrons as high as 0.1 cm2/(V s) is observed in n-channel thin film transistors fabricated from a solution spin-coated conjugated ladder polymer, poly(benzobisimidazobenzophenanthroline) (BBL), under ambient air conditions. This is the highest electron mobility observed to date in a conjugated polymer semiconductor. Comparative studies of n-channel thin film transistors made from a structurally similar nonladder conjugated polymer BBB gave an electron mobility of 10-6 cm2/(V s). These results demonstrate that electron transport can be as facile as hole transport in conjugated polymer semiconductors and that ladder architecture of a conjugated polymer can substantially enhance charge carrier mobility.