Nd~(3+)离子掺杂氧化物玻璃的光谱性质

高温熔融法制备了69.5B2O3-20Li2O-(10-χ)CaO-χPbO-0.5Nd2O3(χ=1,3,5,7,mol%)和68.5Li2O-(29-φ)CaO-φAl2O3-2La2O3-0.5Nd2O3(φ=3,7,10,15,mol%)玻璃,测量了玻璃样品的吸收和发射光谱(800nm激光二极管激发),从吸收光谱出发,应用Judd-Ofelt理论获得了Nd3+光学跃起的强度参数。根据强度参数和发射光谱,计算了Nd3+离子4F3/2→4I11/2跃迁的荧光发射截面σe。结果显示,在B2O3-Li2O-CaO-PbO-Nd2O3系统中随着CaO的减少和PbO的增加,Nd3+离子的强度参数Ω2增大,表明样品的对称性降低;强度参数Ω6也增大,说明玻璃样品中Nd-O键的共价性和键强降低;同时,Nd3+离子4F3/2→4I11/2跃迁的荧光发射截面σe的大小和荧光强度都减小。在Li2O-CaO-Al2O3-La2O3-Nd2O3系统中,随着CaO的减少和Al2O3的增加,Nd3+离子的强度参数Ω2减小,说明样品的对称性增加;强度参数Ω6减小,说明玻璃样品中Nd-O键的共价性和键强增强;同时,Nd3+离子4F3/2→4I11/2跃迁的荧光发射截面的大小和荧光强度也都减小。     

TeO2-TiO2-Bi2O3系统玻璃的热学特性及光学带隙研究

采用熔融淬冷法制备了系列高折射率的TeO2-TiO2-Bi2O3系统玻璃,测试了样品的密度、转变温度、析晶温度、折射率、吸收光谱,利用经典的Tauc方程计算了样品光学带隙允许的直接跃迁、允许的间接跃迁及Urbach能量.讨论了玻璃的热稳定性与组成之间的关系、研究了摩尔折射度、金属标准值、光学带隙、Urbach能量、Bi2O3和TiO2含量及光学碱度对玻璃样品折射率的影响.结果表明TeO2-TiO2-Bi2O3玻璃具有较好的热稳定性、样品的折射率随着摩尔折射度增大而增大,而光学带隙及金属标准值有减小的趋势,此外高的光学碱度对玻璃的高的三阶非线性也有一定的贡献.     

从Eu^3＋发散光谱获得J—O参数Ω2、Ω4

测量了Eu^3 掺杂的PbF2和H3BO3不同配比玻璃材料的吸收光谱、发射光谱及激发光谱，计算了各不同配比样品的折射率。根据稀土离子Eu^3 光学跃迁矩阵元的特点，从发射光谱获得了Eu^3 光学跃迁的J－O参数Ω2和Ω4,并研究了Ω2和Ω4对xPbF2-(79.5-x)H3BO3-0.5Eu2O5玻璃体系组分的依赖关系，提出了用Eu^3＋离子作为玻璃材料微观环境 探针，并通过实验证实了其可行性。     

从Eu3+发射光谱获得J-O参数Ω2、Ω4

测量了Eu3 + 掺杂的PbF2 和H3 BO3 不同配比玻璃材料的吸收光谱、发射光谱及激发光谱 ,计算了各不同配比样品的折射率。根据稀土离子Eu3 + 光学跃迁矩阵元的特点 ,从发射光谱获得了Eu3 + 光学跃迁的J O参数Ω2 和Ω4 ,并研究了Ω2 和Ω4 对xPbF2 ( 79 5-x)H3 BO3 0 5Eu2 O5玻璃体系组分的依赖关系 ,提出了用Eu3 + 离子作为玻璃材料微观环境探针 ,并通过实验证实了其可行性。     

Ho3+掺杂GeO2-Ga2O3-Li2O-BaO-La2O3玻璃的光谱和增益特性的计算

用高温熔融法制备了不同Ho3+浓度掺杂的65GeO2-12Ga2O3-8Li2O-10BaO-5La2O3-χHo2O3锗酸盐玻璃.从吸收光谱出发,应用Judd-Ofelt理论,获得了Ho3+离子的跃迁强度参量（Ω2,Ω4,Ω6）,并由此计算了Ho3+离子的自发辐射跃迁几率A,荧光分支比β,辐射能级寿命τ等光谱参量.根据McCumber理论,计算了Ho3+离子能级5I8→5I7（2.0 μm）跃迁的吸收截面和受激发射截面,同时也获得了相应的反映粒子数反转的增益截面光谱.钬掺杂的锗酸盐玻璃,其增益截面的最大值比所报道的氟锆铝酸盐玻璃大.结果表明,Ho3+掺杂的锗酸盐玻璃在2.0 μm附近波段的中红外激光器中将有一定的应用前景.     

EDWA基质玻璃中Er3+的光谱参数计算

对制备的不同掺杂Er3+浓度的硅酸盐玻璃,测定了吸收光谱和荧光光谱.根据玻璃的光谱特性计算了玻璃吸收面积并确定出体系的最佳掺杂Er2O3浓度为0.2左右.根据Judd-Ofelt理论拟合出光谱强度参数Ωλ(λ=2,4,6);结果分析表明:随着Er3+离子浓度的增加,光谱强度参数Ω2在增大,Ω6在减小,说明玻璃的共价性能增强,Er-O共价性增强.     

KCl对GeS_2-Ga_2S_3硫系玻璃光学性能的影响

采用熔融淬冷法制备了GeS2-Ga2S3-KCl系统玻璃,然后测试了样品的厚度、密度、吸收光谱和透射光谱,利用经典的Tauc方程计算了样品光学带隙允许的直接跃迁。结果显示,GeS2-Ga2S3-KCl玻璃拥有较好的物理性能;样品的密度、折射率随着KCl含量增多而减小,而光学带隙则随着KCl含量增加而增大。此外,傅里叶和拉曼红外光谱仪的测试结果表明,随着KCl加入和含量的增加,玻璃基质网络结构发生变化,从而引起相应红外光学性能的改变;同时玻璃拉曼谱出现阶段性的变化,红外截止边带出现了规律性的红移。通过研究KCl含量对基质玻璃的结构影响,给出了硫卤玻璃中基频声子振动与红外多声子吸收截止特性的定量描述,归纳了该类硫卤玻璃的光学性质与基质的依赖关系。     

过渡金属Fe或Ag掺杂K_2Ti_6O_(13)的电子结构和光学性质（英文）

本文利用基于密度泛函理论(DFT)的第一性原理计算研究了它们的电子结构和光学性质.光学性质的计算结果和实验相一致.结果表明,Fe或Ag掺杂后,K_2Ti_6O_(13)的带隙中出现了杂质带且其带隙值变小,因而使掺杂后的K_2Ti_6O_(13)的吸收边发生红移并实现了其对可见光吸收.其中杂质带主要由Fe 3d态或Ag 4d态与Ti 3d态和O 2p态杂化而成.对于Fe掺杂的K_2Ti_6O_(13),杂质带位于带隙中间,因此可以作为电子从价带跃迁到导带的桥梁.对于Ag掺杂的K2Ti6013,杂质带位于价带顶附近为受主能级,可以降低光生载流子的复合概率.实验和计算研究表明,通过Fe或Ag的掺杂可以实现了K_2Ti_6O_(13)对可见光的吸收,这对进一步研究K_2Ti_6O_(13)的光学性质具有重要意义.     

PbI2对远红外Te基硫系玻璃光学性能的影响

用传统的熔融淬冷法制备了一系列新型Ge-Te-PbI₂硫系玻璃,并且讨论了玻璃的形成区域. 利用X射线衍射(XRD)、差热分析(DTA)、可见/近红外吸收光谱、红外透过光谱等技术,研究重金属卤化物PbI₂对Ge-Te硫系玻璃组成、结构和性能的影响. 利用Tauc方程计算了样品的直接和间接光学带隙,根据金属标准和能量带隙理论讨论了玻璃光学带隙与组分变化的关系. 结果表明:PbI₂的引入,提高了Te玻璃的形成能力,而且玻璃的热稳定性良好;随着PbI₂含量的增加,玻璃的密度和折射率均增大,光学带隙减小,短波吸收截止边发生红移,玻璃的红外截止波长基本不变,达到了25 μm. 该系列玻璃可用于制备远红外长波波导器件. 关键词： Te基玻璃 2')" href="#">PbI₂ 光学带隙 红外光谱     

A-La2O3电子结构和光学性质的第一性原理计算

采用基于密度泛函理论(DFT)框架下广义梯度近似平面波超软赝势法,计算A-La2O3的电子结构和光学性质.结果表明,A-La2O3,属于间接带隙氧化物,禁带宽度为3.72 eV;其价带主要由La的5s,5p和6s态电子以及O的2s和2p态电子构成,导带主要由La的5d态电子构成.经带隙校正后,计算得到A-La2O3在(100)和(001)方向上的光学线性响应函数随光子能量的变化关系,包括复介电函数、复折射率、吸收光谱、反射光谱、损失函数和光电导谱.结果表明,A-La2O3,在(100)和(001)方向上具有光学各向异性,并且具有从近紫外到红外的透明区域,为A-La2O3,的应用提供了理论依据.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.