Oxygen permeability of La2Cu(Co)O4+δ solid solutions

Formation of the La₂Cu_1−xCo_xO_4+δ solid solutions with orthorhombic K₂NiF₄-type structure was found to be in the range of 0≤x≤0.30 at temperatures above 1270 K. Incorporating cobalt into the copper sublattice of lanthanum cuprate leads to increasing oxygen hyperstoichiometry and decreasing electrical conductivity. Thermal expansion coefficients of the La₂Cu_1−xCo_xO_4+δ (x=0.02–0.30) ceramics at 470–1100 K were calculated from the dilatometric data to vary in the range (12.2–13.2)×10⁻⁶ K⁻¹. Studying the dependence of oxygen permeation fluxes through La₂Cu(Co)O_4+δ on the membrane thickness demonstrated that the oxygen transport at the thickness values below 1 mm is limited by both surface exchange rate and bulk ionic conductivity. Oxygen permeability of the La₂Cu_1−xCo_xO_4+δ solid solutions was ascertained to increase with cobalt concentration at x=0.02–0.10 and to decrease with further dopant additions, indicating a participation of interstitial oxygen in the ionic transport.     

Characterization of nonstoichiometric nickel manganite spinels NixMn3−x□3δ/4O4+δ by temperature programmed reduction

Cation deficient spinels Ni_xMn_3−x□_3δ/4O_4+δ (0≤x≤1) have been prepared by thermal decomposition of mixed oxalates Ni_x/3Mn_(3−x)/3(C₂O₄)·nH₂O in air at 623 K. They have been characterised by temperature programmed reduction (TPR) under H₂, the reaction being followed by gravimetric and powder X-ray diffraction measurements. It has been shown that TPR proceeds in several steps. The first steps correspond to the loss of nonstoichiometric oxygen leading to the formation of a stoichiometric oxide. During the following stages the manganese cations are reduced, causing the spinel structure to be destroyed, and the formation of solid solution of NiO in a cubic MnO. Subsequently, Ni²⁺ cations undergo a reduction to metallic nickel, and, finally, a mixture of nonstoichiometric MnO_1−δ and metallic nickel is formed. These oxides contain a high level of vacancies which vary with the nickel content with a maximum of δ≈1 near x=0.6. This nonstoichiometry is ascribed both to the presence of Ni³⁺ and excess of Mn⁴⁺.     

Perovskite-like system (Sr,La)(Fe,Ga)O3−δ: structure and ionic transport under oxidizing conditions

The maximum solid solubility of gallium in the perovskite-type La_1−xSr_xFe_1−yGa_yO_3−δ (x=0.40–0.80; y=0–0.60) was found to vary in the approximate range y=0.25–0.45, decreasing when x increases. Crystal lattice of the perovskite phases, formed in atmospheric air, was studied by X-ray diffraction (XRD) and neutron diffraction and identified as cubic. Doping with Ga results in increasing unit cell volume, while the thermal expansion and total conductivity of (La,Sr)(Fe,Ga)O_3−δ in air decrease with gallium additions. The average thermal expansion coefficients (TECs) are in the range (11.7–16.0)×10⁻⁶ K⁻¹ at 300–800 K and (19.3–26.7)×10⁻⁶ K⁻¹ at 800–1100 K. At oxygen partial pressures close to atmospheric air, the oxygen permeation fluxes through La_1−xSr_xFe_1−yGa_yO_3−δ (x=0.7–0.8; y=0.2–0.4) membranes are determined by the bulk ambipolar conductivity; the limiting effect of the oxygen surface exchange was found negligible. Decreasing strontium and gallium concentrations leads to a greater role of the exchange processes. As for many other perovskite systems, the oxygen ionic conductivity of La_1−xSr_xFe_1−yGa_yO_3−δ increases with strontium content up to x=0.70 and decreases on further doping, probably due to association of oxygen vacancies. Incorporation of moderate amounts of gallium into the B sublattice results in increasing structural disorder, higher ionic conductivity at temperatures below 1170 K, and lower activation energy for the ionic transport.     

Trapping mechanism of superconductivity suppression induced by Pr substitution in the Ho1−xPrxBa2Cu3O7−δ system

Pr concentration dependence of the superconducting transition temperature T_c in the Ho_1−xPr_xBa₂Cu₃O_7−δ system is determined from measurements of DC electrical resistance. This dependence coincides with that for the parallely studied Y_1−xPr_xBa₂Cu₃O_7−δ reference system. Both systems have the same value of the critical concentration x_c=0.58, in accordance with nearly equal ionic radii of Ho³⁺ and Y³⁺ ions. It has been shown that the T_c(x) curve can be described with a single mechanism based on a decreasing number of sheet holes trapped by Pr^IV-ions, if one takes also into account that the number of these ions changes with x.     

Phase transitions and electrical properties of CsH(SO4)0.76(SeO4)0.24 mixed crystals

The study by X-ray diffraction, calorimetry, vibrational and impedance spectroscopy of CsH(SO₄)_0.76(SeO₄)_0.24 new solid solution is presented. Crystals of this composition undergo two phase transitions at T = 333 and 408 K. The last one at 408 K is a superionic-protonic transition (SPT) related to a rapid [HS(Se)O₄⁻] reorientation and fast H⁺ diffusion. A sudden jump in the conductivity plot confirms the presence of this transition. Above 408 K, this high temperature phase is characterized by high electrical conductivity (7 × 10^t-3 Ω⁻ cm⁻¹) and low activation energy (E_a < 0.3 eV).     

Intercalation thermodynamics and chemical diffusion of oxygen in the solid solution YBa2Cu3−xCoxO6+δ

The equilibrium oxygen content as a function of the temperature and oxygen pressure was measured for the solid solution YBa₂Cu_3−xCo_xO_6+δ, where x=0, 0.2, 0.4, 0.6, 0.8, by using coulometric titration in the temperature range 600–850°C and oxygen pressures between 10⁻⁵ and 1.0 atm. The change in the partial molar enthalpy and entropy of the intercalated oxygen was determined at different oxygen and cobalt contents. The oxygen chemical diffusion was studied by thermogravimetric relaxation in the oxygen-controlled atmosphere. The thermodynamic data were employed to determine how the chemical diffusion coefficient, the thermodynamic factor and the random-diffusion coefficient depend on oxygen content in specimens with different cobalt concentration. The oxygen intercalation thermodynamics and diffusivity results provide evidence of ordering phenomena on a microscopic scale in the basal plane of the tetragonal solid solution YBa₂Cu_3−xCo_xO_6+δ. A model for the oxygen diffusion is suggested to explain the large difference between the random and tracer diffusion coefficients in YBa₂Cu₃O_6+δ     

Mixed conductivity in SrCe0.95Yb0.05O3 protonic conductors

The results of electrical conductivity measurements on SrCe_0.95Yb_0.05O₃ under controlled oxygen partial pressure and temperature are presented. A defect model consistent with experimental results is proposed which provides for P_O2^−1/4 dependent n-type, P_o2-independent oxygen ion and P_O2^+1/4 dependent p-type conductivity components. The band gap, reduction, oxidation and ion-migration energies are determined from an analysis of the data in terms of the proposed defect model. These results suggest that some earlier data interpreted in terms of protonic conduction may require re-evaluation.     

Ion-pair and triple-ion studies of some tetraalkylammonium halides in pure 1,3-dioxolane at 298.15 K

Conductivities of some tetraalkylammonium halides, viz. tetramethylammonium iodide (Me₄NI), tetraethylammonium bromide (Et₄NBr), tetraethylammonium iodide (Et₄NI), tetra-n-propylammonium bromide (Pr₄NBr), tetra-n-butylammonium bromide (Bu₄NBr), tetra-n-butylammonium iodide (Bu₄NI) and tetra-n-heptylammonium bromide (Hp₄NBr) were measured at 298.15 K in 1,3-dioxolane which has a low permittivity (ε = 7.13). A minima in the conductometric curves (molar conductance, Λ vs. square root of concentration, √c) was observed for concentrations which were dependant upon both the salt and the solvent. The observed molar conductivities were explained by the formation of ion-pairs (M⁺ + X⁻ ↔ MX, K_P) and triple-ions (2M⁺ + X⁻ ↔ M₂X⁺; M⁺ + 2X⁻ ↔ MX₂⁻, K_T). A linear relationship between the triple-ion formation constants [log (K_T/K_P)] and the salt concentrations at the minimum conductivity (log C_min) was given for all the salts in 1,3-dioxolane. The formation of triple-ions might be attributed to the ion sizes in solutions in which Coulombic interactions and non-Coulombic interactions act as the main forces between the ions (R₄N⁺…..X⁻).     

Effect of WO3 on the spectroscopic properties in Er/Yb co-doped bismuth–borate glasses

The spectroscopic properties of Er³⁺/Yb³⁺ co-doped Bi₂O₃–B₂O₃–WO₃ (BBW) glasses were analyzed and discussed. The effect of WO₃ content on the absorption spectra, the Judd–Ofelt parameters Ω_t (t=2, 4, 6), emission spectra and the lifetime of the ⁴I_13/2 level and the quantum efficiency of Er³⁺:⁴I_13/2→⁴I_15/2 transition were also investigated. With the substitution of WO₃ for B₂O₃, the measured lifetime of the ⁴I_13/2 level and the quantum efficiency of Er³⁺:⁴I_13/2→⁴I_15/2 transition increase from 0.98 to 1.31 ms and from 38.2% to 49.2%, respectively. The effective width of emission band and the emission cross-section both decrease slightly. And the emission spectra is analyzed via the different curve (σ_e−σ_a) of BBW glasses, the influence of OH⁻is also discussed.     

Transport properties of SrCe0.95Y0.05O3−δ and its application for hydrogen separation

Transport properties of SrCe_0.95Y_0.05O_3−δ were studied by impedance spectroscopy and by measuring open-cell voltage (OCV) and gas permeation. Ionic transference numbers were determined by measuring the OCV of concentration cells and water vapor evolution of an O₂/H₂ fuel cell. We observed interfacial polarization on the basis of the I–V curves obtained by discharging a hydrogen concentration cell or an O₂/H₂ fuel cell. The observed high protonic conductivity (high proton and low oxide ion transference numbers) makes SrCe_0.95Y_0.05O_3−δ a potential material for hydrogen separation. From proton conductivity measurements, under a given hydrogen partial pressure difference of 4%/0.488%, the hydrogen permeation rate (of a dense membrane with 0.11 cm in thickness) was calculated to be ≈0.072 cm³ (STP) cm⁻² min⁻¹ at 800°C, whereas the permeation rate calculated from short-circuit current measurements was ≈0.023 cm³ (STP) cm⁻² min⁻¹ at 800°C. The difference between calculated and observed permeation rates is probably due to interfacial polarization.     

Phonon Raman scattering in Nd1+xBa2−xCu3O7−δ and Pr1+xBa2−xCu3O7−δ single crystals

The polarized Raman spectra of Nd_1+xBa_2−xCu₃O_7−δ (−0.023≤x≤0.107) and Pr_1+xBa_2−xCu₃O_7−δ (0.01≤x≤0.15) single crystals have been investigated. It was found that the Cu(2) A_g mode softens by 6 cm⁻¹ in Nd 1:2:3 and 4 cm⁻¹ in Pr 1:2:3 as x increases. These frequency shifts cannot be explained by the change in the relevant bond lengths due to Nd(Pr)-substitution for Ba. The variations with x of the two low frequency modes may be affected by change of their hybridization and/or change of their force constants. The linewidths of Ba mode in Pr 1:2:3 are broader than those in Y 1:2:3. This result suggests that the Pr substitution on Ba sites occurred even in a very small value of x. In x(yy) geometry the relative intensity of the Ba and O(4) modes in Nd 1:2:3 is greater than those in Pr 1:2:3. The difference between Nd 1:2:3 and Pr 1:2:3 in the relative intensity of the Ba and O(4) modes may be produced by the chains.     

Sr-doped LaInO3 and its possible application in a single layer SOFC

The effects of dopants on the electrical conductivity of the perovskite-type oxide LaInO₃ have been investigated. Replacement of La by Sr is the most effective way to enhance the conductivity of LaInO₃, whereas Ca substitution for In is rather difficult due to the large difference in the ion radii. The optimum composition is La_0.9Sr_0.1InO_3−δ whose maximum conductivity is 7.6×10⁻³ S cm⁻¹ at 900°C. The electrical conductivity of La_0.9Sr_0.1InO_3−δ has been measured over a wide range of oxygen partial pressure from pO₂=1 to 10⁻²⁵ atm. P-type and n-type behavior at high and low oxygen partial pressure have been observed, respectively, while at intermediate oxygen partial pressures, the electrical conductivity changes only slightly with the oxygen partial pressure. The concept of a single layer solid oxide fuel cell based on a La_0.9Sr_0.1InO_3−δ ceramic pellet has been tested. A maximum power density of 3 mW cm⁻² at 800°C was achieved when dilute H₂ and air were used as fuel and oxidizing agent, respectively.     

Current–voltage characteristic of BaTiO3−δ in its mixed n/p regime under oxygen potential gradients

Current (I)–voltage (V) characteristic under oxygen potential gradients was experimentally examined on single crystal BaTiO_3−δ in its mixed ion/electron/hole regime at 1000 °C. The variation of I vs. V appears similar to that of an n/p junction, but with the limiting slope (dI/dV) approaching the maximum and minimum possible equilibrium conductances in the given oxygen potential gradient as increasing forward and reverse bias, respectively. This characteristic has been precisely traced theoretically by using the partial ionic and electronic conductivities of BaTiO_3−δ as measured against uniform oxygen chemical potential in equilibrium state. The nonlinear characteristic is attributed to the redistribution of oxygen chemical potential that is caused by a non-vanishing gradient of the ionic transference number of the oxide under the given oxygen potential gradient. It is demonstrated that the bulk transport properties of a mixed conductor may be tailored by terminal voltage in a chemical potential gradient.     

Deuterium conductivity, diffusion and implantation in Sr-doped LaYO3

A study of deuterium conductivity and diffusion in the oxide perovskite La_0.9Sr_0.1YO_3−δ is presented in this work. Deuterium ions were implanted into La_0.9Sr_0.1YO_3−δ (50 keV, 1×10¹⁶ atoms/cm²) and the corresponding deuterium depth profile was determined by SIMS and compared with a Monte Carlo simulation (TRIM96). This implant was used as a standard for the determination of deuterium concentration in a La_0.9Sr_0.1YO_3−δ sample pre-treated in D₂O atmosphere. In this way, it was fully confirmed that La_0.9Sr_0.1YO_3−δ incorporates water at high temperatures. The conductivity of La_0.9Sr_0.1YO_3−δ was measured in D₂O atmosphere and compared with other proton (deuteron) conductors. Concentration and conductivity data were used in conjunction to estimate the deuterium diffusivity and the constant of reaction of (heavy) water incorporation into LaYO₃. Some comments on the catalytic activity of this oxide are made.     

Anharmonic V–V pumping and asymmetric electron-elementary excitation interaction in emission and absorption of O2(Δg) in the crystalline phases of oxygen

Three luminescence bands in the yellow and red spectral region, which are related to the ¹Δ_g¹Δ_g→³Σ_g^{− 3}Σ_g⁻ double electronic transition of O₂, have been investigated in the , β, and γ phase of solid oxygen. The temperature dependence of the intensity of the yellow band is strongly influenced by emission from higher vibrational levels of O₂(¹Δ_g), which are populated by anharmonic V–V pumping. The broken mirror symmetry of the luminescence and absorption bands in the phase of solid O₂ points to an interaction between the electrons and the elementary excitations of the crystal, which is different in the ground and excited electronic states, e.g., a quadratic electron–phonon interaction.     

Germanium and iron co-substituted SrCoO2.5+δ as oxygen permeable membrane

Germanium and iron co-doped SrCoO_2.5+δ was investigated in terms of phase stability, oxygen permeability and electrical conductivity. The favorable high-temperature cubic structure of SrCoO_2.5+δ was stabilized to lower temperatures by co-doping Ge (10 mol%) and Fe (10 mol%) that substituted for Co, which however could not be achieved by doping Ge (20 mol%) alone. In contrast to SrCo_0.8Ge_0.2O_2.5+δ sample which showed a sharp decrease in oxygen permeability at temperature of 875 °C upon cooling, SrGe_0.1Co_0.8Fe_0.1O_3−δ sample remained well-permeable to oxygen at lower temperatures down to at least 820 °C; an abrupt change in electrical conductivity in SrCo_0.8Ge_0.2O_2.5+δ also occurred accompanying the phase transition. The oxygen permeation flux for SrGe_0.1Co_0.8Fe_0.1O_3−δ increased significantly with the decrease of the membrane thickness, indicating the transport of oxygen ions in the bulk of the membrane as the rate-limiting step.     

Superconducting Nd1.85Ce0.15CuO4 films grown by the pulsed electron deposition technique

Nd_1.85Ce_0.15CuO_4−δ superconducting thin films were prepared on (1 0 0) SrTiO₃ substrates by pulsed electron deposition technique without reducing atmosphere. Oxygen content is finely controlled by high temperature vacuum annealing, and optimal superconductivity has been obtained. The deposition conditions of the film are discussed in details. Higher deposition temperature and lower gas pressure result in the loss of copper and the appearance of the foreign phase Ce_0.5Nd_0.5O_1.75. High quality Nd_1.85Ce_0.15CuO_4−δ epitaxial films are deposited at 840–870 °C in the mixed gas with a ratio of O₂:Ar = 1:3.     

Evidence for pinning by (Sr,Ca)2CuOy particles in partial-melting processed bulk Bi2Sr2CaCu2O8+δ ceramics

Flux distributions of partial-melting processed Bi₂Sr₂CaCu₂O_8+δ ceramics are obtained using magneto-optic imaging. In remanent states (μ₀H_a=0 T), large amounts of trapped flux are observed along (Sr,Ca)₂CuO_y particles embedded in the Bi₂Sr₂CaCu₂O_8+δ matrix. Despite the relatively large size of these particles (up to 30 μm), the pinning effect is similar to that of Y₂BaCuO₅ particles in melt-processed YBa₂Cu₃O_7−δ. Furthermore, we discuss how the pinning capability of non-superconducting particles of different sizes and densities will show up in magneto-optic images.     

Cl nuclear quadrupole resonance studies of molecular motions of ClO3 and water diffusion in Ca(ClO3)2·2H2O

A ³⁵Cl nuclear quadrupole resonance (³⁵Cl-NQR) investigation of polycrystalline Ca(ClO₃)₂·2H₂O is described. The ³⁵Cl-NQR frequencies (ν_Q) for two resonance lines (ν_Q1 and ν_Q2), the spin lattice relaxation time (T_1Q) for ν_Q2 only and the line width δν_Q2 were measured in the temperature range 292–345 K, except for the frequency measured up to 455 K. The observed decrease in the resonance frequencies with increasing temperature permitted the determination of the frequencies of librations of the ClO₃⁻ ion about two axes perpendicular to the three-fold axis of the ion mainly responsible for this effect. The temperature dependence of the relaxation time T_1Q proved the occurrence of water diffusion and hindered rotation of ClO₃⁻ ions. The activation energies of these two molecular motions were determined, and their effect on the electric field gradient at the site of a chlorine nucleus was discussed. Temperature measurements of the line width δν_Q2 confirmed the conclusions drawn from the analysis of T_1Q(T).