Relationship between phase structure and electrical properties of (K0.5Na0.5)NbO3-LiTaO3 lead-free ceramics

Lead-free piezoelectric ceramics of (1−x)K_0.5Na_0.5NbO₃-xLiTaO₃ (KNN-LT) system have been investigated in this work. X-ray diffraction, Raman spectra measurements, DSC (Differential Scanning Calorimetric), and dielectric constant versus temperature provide direct evidence that the phase transition temperature between tetragonal and orthorhombic shift to lower temperature with the increasing of LT content. The KNN-0.05LT ceramics exhibit the highest high-field d₃₃ up to 220 pm/V. At the same time, we also investigated the relationship between phase structure and electric properties, showing that the orthorhombic phase presents better piezoelectric temperature stabilities than the tetragonal phase. The result may provide a new way for KNN-based lead-free ceramics.     

Microstructure and piezoelectric properties of Bi0.5(Na0.82K0.18)0.5TiO3−NaSbO3 ceramics

Lead-free piezoelectric ceramics (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ have been prepared by a conventional ceramics technique, and their microstructure and electrical properties have been investigated. The addition of NaSbO₃ has no remarkable effect on the crystal structure within the studied doping content; however, an obvious change in microstructure took place. With increase in NaSbO₃ content, the temperature from a ferroelectric to antiferroelectric phase transition increases, and the temperature for a transition from antiferroelectric phases to paraelectric phases changes insignificantly. Simultaneously, the temperature range between the rhombohedral phase transition point and the Curie temperature point becomes smaller. The piezoelectric properties significantly increase with increase in NaSbO₃ content and the piezoelectric constant and electromechanical coupling factor attain maximum values of d₃₃=160 pC/N and k_p=0.333 at x=0.01. The results indicate that (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ ceramic is a promising lead-free piezoelectric candidate material.     

Structural, ferroelectric and impedance spectroscopy properties of Y modified Pb(Fe0.5Nb0.5)O3 ceramics

Some ceramic samples of Pb_1−xY_x(Fe_0.5Nb_0.5)_1−x/4O₃ (PYFN) (0.00≤x≤0.08) were synthesized by a mixed oxide route. X-ray diffraction patterns of all the above samples confirm the formation of single phase material crystallizing in monoclinic structure. Dielectric properties (ε_r and tan δ) were analyzed in a wide temperature (30-350 °C) and frequency range (100 Hz-1 MHz). Ferroelectric properties of these compounds were confirmed from polarization (P-E hysteresis loop) measurements at room temperature. All the room temperature hysteresis loops of PYFN ceramics were well simulated using the ferroelectric capacitor model. Yttrium substitution resulted in notable enlargement of room temperature remnant polarization (2P_r). The 2P_r of PYFN (x=0.02) reaches to a large value (23 μC/cm²), which is nearly 5 times greater than that of PFN ceramic (4.6 μC/cm²). All the compounds exhibits negative temperature coefficient of resistivity (NTCR) type behavior as that of semiconductors. Dc conductivity (estimated via bulk resistivity) variation with temperature of all the samples follows Arrhenius type of electrical conductivity.     

Dielectric and piezoelectric properties of lead-free (Na0.5K0.5)NbO3-SrTiO3 ceramics

In this article, we report successful preparation of dense [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ (x=0.005-0.100) ceramics by ordinary sintering in air. The dependence of phase structure on doping content of SrO and TiO₂ has been determined by the X-ray diffraction technique. It was found that the crystal structure changed from orthorhombic to tetragonal at x≈0.040. Dielectric study revealed that the dielectric relaxor behavior was induced by doping of SrO and TiO₂ into (Na_0.5K_0.5)NbO₃. The samples in the composition range from x=0.005 to 0.020 exhibited excellent electrical properties, piezoelectric constant of electromechanical planar and thickness coupling coefficients of k_p=26.6-32.5% and k_t=39.8-43.8%. The results show that the [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics are one of the promising lead-free materials for electromechanical transducer applications.     

Dielectric properties of valence compensated Ca1−xBixTi1−xCrxO3 perovskite prepared using the sol-gel process

Ca_1−xBi_xNb_1−xCr_xO₃ (x=0.01-0.5) ceramic powders were synthesized using the sol-gel process. The single-phase solids can be presented at x=0.01 and 0.03. The coexistence of orthorhombic perovskite and the secondary phase of BiCrO₃ was verified, as presented for x=0.05-0.5. Grains with a micro-cube topography were obtained for x=0.3-0.5. The average grain size is about 0.4 and 1.1 μm for x=0.3 and 0.5, respectively. The highest dielectric constant peak was measured at around 55 °C for x=0.5 and at 75 °C for x=0.3. The high dielectric constant was caused by the formation of barrier layers at the interface of the bi-phase mixed ceramics. Space charge polarization contributed to the observed behavior.     

Na0.5K0.5NbO3-BiFeO3 lead-free piezoelectric ceramics

Lead-free (Na_0.5K_0.5)NbO₃-based piezoelectric ceramics were successfully fabricated by substituting with a small amount of BiFeO₃ (BF). Difficulty in sintering of pure NKN ceramics can be eased by adding a few molar percent of BF, and the crystalline structure is also changed, leading to a morphotropic phase boundary (MPB) between ferroelectric orthorhombic and rhombohedral phases. The MPB exists near the 1-2 mol% BF-substituted NKN compositions, exhibiting enhanced ferroelectric, piezoelectric, and electromechanical properties of P_r=23.3 μC/cm², d₃₃=185 pC/N, and k_p=46%, compared to an ordinarily sintered pure NKN ceramics. The MPB composition has a Curie temperature of ∼370 °C, comparable to that of some commercial PZT materials.     

Electrical properties of SrBi2(Nb0.5Ta0.5)2O9 ceramics

Aurivillius SrBi₂(Nb_0.5Ta_0.5)₂O₉ (SBNT 50/50) ceramics were prepared using the conventional solid-state reaction method. Scanning electron microscopy was applied to investigate the grain structure. The XRD studies revealed an orthorhombic structure in the SBNT 50/50 with lattice parameters a=5.522 Å, b=5.511 Å and c=25.114 Å. The dielectric properties were determined by impedance spectroscopy measurements. A strong low frequency dielectric dispersion was found to exist in this material. Its occurrence was ascribed to the presence of ionized space charge carriers such as oxygen vacancies. The dielectric relaxation was defined on the basis of an equivalent circuit. The temperature dependence of various electrical properties was determined and discussed. The thermal activation energy for the grain electric conductivity was lower in the high temperature region (T>303.6 °C, E_a−ht=0.47 eV) and higher in the low temperature region (T<303.6 °C, E_a−lt=1.18 eV).     

Dielectric properties and phase transitions of (Pb0.87La0.02Ba0.1)(Zr0.6Sn0.4−xTix)O3 ceramics with compositions near AFE/RFE phase boundary

The electrical properties and phase transition behavior of (Pb_0.87La_0.02Ba_0.1)(Zr_0.6Sn_0.4−xTi_x)O₃ solid solutions (PLBZST, 0.04≤x0.2) were investigated by the X-ray diffraction, permittivity, pyroelectric current, and P-E electric hysterisis loops. As the composition x increased from 0.04 to 0.2, the antiferroelectric ceramics (x≤0.07, AFE) with tetragonal phase changed to the ferroelectric relaxors (RFE, 0.09≤x). AFE ceramics showed a peculiar diffuse phase transition and dielectric relaxation at the low temperature (down to −100 °C) due to a frustration between AFE and FE state. With an increase in composition x, electrically field-induced AFE-FE switching field (E_AFE-FE) and AFE-paraelectric (PE) phase transition temperature (T_c) are depressed in the temperature (T)-Ti composition (x) phase diagram, a FE-AFE-PE triple phase point (T_tr) with the lowest transition temperature occurred at x=0.09. The pyroelectric currents under an application of various external electric field (E) were measured to identify a T-E phase diagram of the PLBZST compound.     

Effect of 3d metal ion doping on the structure and superconductivity of (Tl0.5Pb0.5)Sr2CaCu2O7

(Tl_0.5Pb_0.5)Sr₂Ca(Cu_2−xM_x)O₇ (M=Co, Ni and Zn) have been synthesized and investigated by means of X-ray diffraction, scanning electron microscope, electrical resistivity and magnetic susceptibility measurements. X-ray diffraction patterns show that all studied samples contain the nearly single ‘1212’ phase. They crystallize in a tetragonal unit cell with a=3.8028-3.8040 Å and c=12.0748-12.1558 Å. In (Tl_0.5Pb_0.5)Sr₂Ca(Cu_2−xM_x)O₇ system (M=Co or Ni), the superconducting critical temperature T_c decreases linearly with both Co and Ni concentrations and the rate of T_c decrease is around −6.5 and −7.0 K/at%, respectively. For (Tl_0.5Pb_0.5)Sr₂Ca (Cu_2−xZn_x)O₇ system, the dependence of T_c on the Zn dopant concentration deviates from a linear behavior and the Zn substitution suppresses T_c much less (−2.5 K/at%) than the Co and Ni substitutions. The suppression in T_c in Co and Ni doped samples are attributed to the magnetic pair-breaking mechanism and the reduction in the carrier concentration. The suppression of T_c in Zn doped samples is not caused by the reduction in carrier concentration which should remain constant, but rather due to nonmagnetic pair-breaking mechanism induced by disorder as well as the filling of the local Cu d_x²−y² state due to the full d band of Zn ions.     

Piezoelectric properties of [Li0.03(K0.48Na0.52)0.97](Nb0.97Sb0.03)O3-(Ba0.85Ca0.15)(Ti0.90Zr0.10)O3 lead-free piezoelectric ceramics

[Li_0.03(K_0.48Na_0.52)_0.97](Nb_0.97Sb_0.03)O₃-(Ba_0.85Ca_0.15)(Ti_0.90Zr_0.10)O₃ [(1−x)LKNNS-xBCTZ] lead-free piezoelectric ceramics were prepared by the conventional solid state method, and effects of BCTZ content on the piezoelectric properties of LKNNS ceramics were mainly investigated. A stable solid solution has been formed between LKNNS and BCTZ, and a morphotropic phase boundary of (1−x)LKNNS-xBCTZ ceramics is identified in the range of 0 < x ≤ 0.02. The Curie temperature of (1−x)LKNNS-xBCTZ ceramics decreases with increasing BCTZ content. A higher ?_r value and a lower tan δ value are demonstrated for the (1−x)LKNNS-xBCTZ ceramic with x = 0.02. The (1−x)LKNNS-xBCTZ ceramic with x = 0.02 has an enhanced electrical behavior of d₃₃ ∼ 237 pC/N, k_p ∼ 48.6%, ?_r ∼ 1451, tan δ ∼ 0.037, and T_c ∼ 335 °C. As a result, (1−x)LKNNS-xBCTZ ceramics are promising candidate materials for the field of lead-free piezoelectric materials.     

DC and AC conductivities of (As2S3)100−x(AsSe0.5Te0.5I)x chalcogenide glasses

The DC and AC conductivities of samples from the system (As₂S₃)_100−x(AsSe_0.5Te_0.5I)_x, where x=0, 5, 10, 15, 20, 25, 30, 35, 50, 70 and 90 mol%, were measured as a function of temperature. Besides, the AC conductivities of the samples with x=10 and 30 were measured as a function of frequency from room temperature to the glass transition temperature. The DC conductivity dependence on temperature is of the Arrhenius type, whereas the value of the pre-exponential factor suggests the electrical conduction by localized states in the band tails and by localized states near the Fermi level. The small values of the conduction activation energy (10⁻²-10⁻¹ eV) obtained at higher frequencies suggest that the conduction in these materials is due to hopping of charge carriers between close defect states near the Fermi level.     

Effect of Cr doping on the magnetic and electrical transport properties of charge-ordered Bi0.5Ca0.5MnO3

An experimental study on the magnetic and electrical transport properties of the manganites Bi_0.5Ca_0.5Mn_1−xCr_xO₃ (BCMCO) (0≤x≤0.12) is carried out. The results show that Cr doping can suppress the charge-ordering transition, favoring the ferromagnetic clusters. For x=0.12, the charge-ordering transition disappears but a very broad paramagnetic-ferromagnetic-like transition is detected at the Curie temperature T_C=72.6 K. It is caused by phase separation or coexistence of the charge-ordering and ferromagnetic phase. Moreover, the critical Cr content to destroy charge ordering phase in BCMCO does not match the general monotonous tendencies shown by Cr-doped Re_0.5Ca_0.5MnO₃ (Re-rare-earth). These differences are ascribed to the fact that the ground state in BCMCO differs markedly from the ferromagnetic metallic phase in Cr-doped Re_0.5Ca_0.5MnO₃ compounds.     

Evolution from relaxor-like dielectric to ferroelectric in Ba[(Fe0.5Nb0.5)1−xTix]O3 solid solutions

Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ (x=0.2,0.4,0.6,0.8,0.85,0.9 and 0.95) solid solutions were synthesized by a standard solid-state reaction technique. X-ray diffraction at room temperature and dielectric characteristics over a broad temperature and frequency range were evaluated systematically. The structure of Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ solid solutions changed from cubic to tetragonal with increasing x. A Debye-like dielectric relaxation following the Arrhenius law similar to that in Ba(Fe_0.5Nb_0.5)O₃ was observed at lower temperature in the composition range 0.2≤x≤0.8, while the relaxor ferroelectric, diffused ferroelectric and normal ferroelectric behavior were observed for x=0.85,0.9 and 0.95, respectively. The process of the evolution of relaxor-like dielectric to ferroelectric suggested the changing from dilute polar micro-domains to polar micro-domains, polar micro/macro-domains and then polar macro-domains in the present ceramics.     

Na1−xLixNbO3 ceramics studied by X-ray diffraction, dielectric, pyroelectric, piezoelectric and Raman spectroscopy

Na_1−xLi_xNbO₃ ceramics with composition 0.05≤x≤0.30 were prepared by solid-state reaction method and sintered in the temperature range 1100-1150 °C. These ceramics were characterised by X-ray diffraction as well as dielectric permittivity measurements and Raman spectroscopy. Dielectric properties of ceramics belonging to the whole composition domain were investigated in a broad range of temperatures from 300 to 750 K and frequencies from 0.1 to 200 kHz. The Rietveld refinement powder X-ray diffraction analysis showed that these ceramics have a single phase of perovskite structure with orthorhombic symmetry for x≤0.15 and two phases coexistence of rhombohedral and orthorhombic above x=0.20. The evolution of the permittivity as a function of temperature and frequency showed that these ceramics Na_1−xLi_xNbO₃ with composition 0.05≤x≤0.15 present the classical ferroelectric character and the phase transition temperature T_C increases as x content increases. The polarisation state was checked by pyroelectric and piezoelectric measurements. For x=0.05, the piezoelectric coefficient d₃₁ is of 2pC/N. The evolution of the Raman spectra was studied as a function of temperatures and compositions. The results of the Raman spectroscopy study confirm our dielectric measurements, and they indicate clearly the transition from the polar ferroelectric phase to the non-polar paraelectric one.     

Post-sintering annealing effect on the diffuse phase transition in (Pb1−xBax)(Yb0.5Ta0.5)O3 ceramics

The effect of post sintering annealing on the dielectric response of (Pb_1−xBa_x)(Yb_0.5Ta_0.5)O₃ ceramics in the diffuse phase transition range (x=0.2) has been investigated. The samples are prepared by conventional solid-state reaction method. The samples are sintered at 1300 °C for 2 h and annealed at different temperatures (800, 900 and 1000 °C) for 8 h and at 800 °C for different time durations (8, 12 and 24 h). A significant change in the dielectric response has been observed in all the samples. The dielectric constant increases remarkably and the dielectric loss tangent decreases. The dielectric peaks of the annealed samples are observed to be more diffused with noticeable frequency dispersion compared to the as sintered sample.     

Properties of non-stoichiometric 0.935(K0.5+xNa0.5+x)NbO3-0.065LiSbO3 lead-free piezoelectric ceramics

0.935(K_0.5+xNa_0.5+x)NbO₃-0.065LiSbO₃ lead-free piezoelectric ceramics were prepared by normal sintering, and their piezoelectric and dielectric properties were investigated by varying the compensating amount x of alkaline elements (Na and K) addition. It was found that the crystal structure changed from tetragonal to orthorhombic with increasing x from −0.010 to 0.010. An MPB was tailored by optimizing the alkaline elements contents. Enhanced electrical and electromechanical responses of d₃₃=253 pC/N, k_p=0.47, k_t=0.45 and tanδ=0.027 were obtained in the ceramics with x=0.005. These excellent piezoelectric and electromechanical properties indicate that this system may be an attractive lead-free material for a wide range of electro-mechanical transducer applications.     

Phase transition, structural and electrical properties of Pb(Zn1/3Nb2/3)O3-doped Pb(Ni1/3Nb2/3)O3-PbTiO3 ceramics prepared by solid-state reaction method

Phase pure perovskite (1−x−y)Pb(Ni_1/3Nb_2/3)O₃-xPb(Zn_1/3Nb_2/3)O₃-yPbTiO₃ (PNN-PZN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via a B-site oxide mixing route. The PNN-PZN-PT ceramics sintered at the optimized condition of 1185 °C for 2 h exhibit high relative density and rather homogenous microstructure. With the increase of PbTiO₃ (PT) content, crystal structure and electrical properties of the synthesized PNN-PZN-PT ceramics exhibit successive phase transformation. A morphotropic phase boundary (MPB) is supposed to form in (0.9−x)PNN-0.1PZN-xPT at a region of x=32-36 mol% confirmed by X-ray diffraction (XRD) measurement and dielectric measurement. The MPB composition can be pictured as providing a “bridge” connecting rhombohedral ferroelectric (FE) phase and tetragonal one since crystal structure of the MPB composition is similar to both the rhombohedral and tetragonal lattices. Dielectric response of the sintered PNN-PZN-PT ceramics also exhibits successive phase-transition character. 0.64PNN-0.1PZN-0.26PT exhibits broad, diffused and frequency dependent dielectric peaks indicating a character of diffused FE-paraelectric (PE) phase transition of relaxor ferroelectrics and 0.40PNN-0.1PZN-0.50PT exhibits narrow, sharp and frequency independent dielectric peaks indicating a character of first-order FE-PE phase transition of normal ferroelectrics. The FE-PE phase transition of 0.56PNN-0.1PZN-0.34PT is nearly first-order with some diffused character, which also exhibits the largest value of piezoelectric constant d₃₃ of 462pC/N.     

Structural and dielectric properties in the (Ba1−xCax)(Ti0.95Zr0.05)O3 ceramics

Lead-free (Ba_1−xCa_x)(Ti_0.95Zr_0.05)O₃ (x = 0.05-0.40) (BCZT) ceramics were prepared by solid-state reaction technique. XRD results show that the samples in the composition range of 0.05 ≤ x ≤ 0.25 exhibit pure perovskite structures and undergo a polymorphic phase transitions from orthorhombic to tetragonal phase around room temperature. The biphasic structures are detected at x ≥ 0.30 and the dielectric peaks become broad and dielectric constants decrease with increasing Ca content. Ca replacement at Ba site leads to diffuseness, whereas Ca occupancy at Ti site leads to decrease of the T_c.     

Structural distortion and phase transition studies of Aurivillius type Sr1−xPbxBi2Nb2O9 ferroelectric ceramics

In this paper, effects of lead doping on the lattice response and phase transitions of Sr_1−xPb_xBi₂Nb₂O₉ (x=0.0-0.5 in steps of 0.1) ferroelectric ceramics are reported. It is observed that structure attains more tetragonality with doping of lead up to 40%. Increased orthorhombic distortion is observed for undoped SBN and 50 at.% lead substituted SBN. Phase transitions for all samples were studied using Curie temperature measurements and are explained in terms of lattice response of these ceramics. Sample with x=0.5 shows decreased tetragonal strain and Curie temperature. Relationship of polarization with lattice response is discussed.     

Enhanced dielectric and ferroelectric properties of Pb1−3x/2Lax(Zr0.5Ti0.5)O3 thin films with low lanthanum substitution

Effects of lanthanum (La) substitution (0.003 ≤ x ≤ 0.015) on the dielectric and ferroelectric properties of Pb(Zr_0.5Ti_0.5)O₃ thin films have been investigated. The films were synthesized on the Pt (1 1 1)/Ti/SiO₂/Si (1 0 0) substrates by a sol-gel method. Large dielectric constants of the films are obtained within range of 800-1600 which are almost comparable to those observed in bulk ceramics. The films also show improved remnant polarization values and reduced coercive field values with the increasing addition of La substitution. Our results suggest that low La substitution contributes to enhance film electric properties due to the improvement of non-180° domain wall mobility as well as the stabilization of tetragonal phase.