阳极氧化法制备阀金属氧化物纳米管的机理及影响因素

阳极氧化法不仅能够简便地制备出阀金属氧化物纳米管,而且通过调节各种参数可以调控所制备纳米管的形貌.阳极氧化法制备的纳米管具有优异的化学/物理性能,在众多领域都得到了广泛应用.本文综述了阳极氧化法制备纳米管膜的基本过程以及三种常见的模型,并以三种具有代表性的阀金属(Al、Ti、Zr)为例,分别介绍了它们形成多孔膜反应过程和常用的制备过程,同时也介绍了其他阀金属及其合金的制备方案.最后,结合对Al、Ti、Zr的实验过程,讨论、分析了电压大小、电解液种类、电解液浓度、反应时间等控制因素对阳极氧化法制备纳米管膜形貌的影响,对制备形貌规整的多孔膜,提高多孔膜在实际应用中的性能具有一定的意义.     

阳极氧化TiO2纳米管阵列的制备与掺杂*

近年来,TiO₂纳米管阵列的制备与应用得到了广泛的研究。阳极氧化法制备TiO₂纳米管阵列具有工艺简单、成本低廉、易于放大等优点,引起了极大关注。本文综述了阳极氧化法制备TiO₂纳米管阵列的研究现状,基于TiO₂纳米管阵列在阳极氧化过程中的生长机理,讨论了决定阳极氧化TiO₂纳米管阵列形成的主要因素。结合本组的研究工作,总结了如何通过改变电压、升压速率、电解液、温度和氧化时间,实现纳米管管径、管壁厚度、管长的有效控制,提高TiO₂纳米管阵列的表面形貌质量。最后介绍了TiO₂纳米管阵列掺杂改性方面的研究进展。     

阳极氧化TiO2纳米管阵列的制备与掺杂

近年来,TiO₂纳米管阵列的制备与应用得到了广泛的研究。阳极氧化法制备TiO₂纳米管阵列具有工艺简单、成本低廉、易于放大等优点,引起了极大关注。本文综述了阳极氧化法制备TiO₂纳米管阵列的研究现状,基于TiO₂纳米管阵列在阳极氧化过程中的生长机理,讨论了决定阳极氧化TiO₂纳米管阵列形成的主要因素。结合本组的研究工作,总结了如何通过改变电压、升压速率、电解液、温度和氧化时间,实现纳米管管径、管壁厚度、管长的有效控制,提高TiO₂纳米管阵列的表面形貌质量。最后介绍了TiO₂纳米管阵列掺杂改性方面的研究进展。     

阳极氧化法制备二氧化钛纳米管阵列的研究

采用电化学阳极氧化法,将纯钛浸入HF酸水溶液,在钛基体表面原位构建高度有序的二氧化钛纳米管阵列,探讨阳极氧化电压、电解液浓度和电解液温度等对二氧化钛纳米管阵列尺寸和形貌的影响。通过SEM、XRD对二氧化钛纳米管阵列的结构特征进行表征,结果表明,不同的阳极氧化电压、电解液浓度和温度都将影响TiO2纳米管阵列的尺寸和形貌,在阳极氧化电压为20V,HF电解液浓度为0.5%t条件下,可制备出结构规整有序的TiO2纳米管阵列。     

TiO_2纳米管阵列薄膜制备及生长机理的研究

本论文采用阳极氧化的方法,在NH4HF2+NH4H2PO4的混合水溶液中于室温下以金属钛为基体原位合成氧化钛纳米管阵列薄膜。讨论了电解液成分、外加电压、溶液的pH值对氧化钛纳米管阵列薄膜微观结构及形貌的影响,并建立了阳极氧化钛纳米管阵列薄膜的生长模型。氧化钛纳米管的结构与外加电压有很大的关系,只有电压在5～35V范围内才能制备出二氧化钛纳米管阵列薄膜,其管径随着电压的升高而增加,且管径范围为30～160nm。而薄膜的厚度与电解液有关,通过控制电解液的成分及pH值,可获得厚度为6.5μm的氧化钛纳米管阵列薄膜。     

NH4F/H3PO4体系中阳极氧化法制备TiO2纳米管阵列

以价廉的Ni板代替常用的Pt片为阴极,纯钛为阳极,采用电化学阳极氧化法在NH4F-H3PO4体系中制备出TiO2纳米管阵列.详细研究了制备参数(溶液酸度、氟离子浓度、外加电压和氧化时间)对所获纳米管阵列形貌的影响.采用场发射扫描电镜(FE-SEM)和X射线衍射(XRD)对样品的形貌和晶相结构进行了表征.在最优化的条件下,可以获得形貌规整、表面干净、有序的TiO2纳米管阵列.纳米管阵列的平均管径为60 nm.管长约530 nm.采用阳极氧化法制备的纳米管阵列是非晶态的.经400℃热处理2 h后,可以转变为锐钛矿相.实验结果还发现,经过热处理后,纳米管阵列变得更为有序,管径扩大至约95 nm.     

微含水量电解液中高管径比TiO_2纳米管阵列的制备

通过阳极氧化法在微含水量为0.5wt%的NH4F/乙二醇/H2O酸性电解质体系中制备了管径大、高管径比的二氧化钛(TiO2)纳米管阵列。采用SEM、XRD等测试手段对TiO2纳米管阵列形貌及晶相进行表征,探讨了不同氧化时间、电压对纳米管阵列形貌的影响,微含水量下氧化电压可以适当增加,更容易得到规整的长纳米管阵列;通过测定样品的光电流和紫外-可见光漫反射吸收光谱,研究分析了含水量以及超声工艺对纳米管光吸收及光电流特性,微含水量下得到的纳米管阵列可见光吸收边红移至420nm,对480~700nm可见光有明显的光吸收,光电流显著增大;丙酮作为超声介质可有效去除纳米管阵列表面的集束,能进一步提高纳米管阵列的光电性能。     

含氯离子电解液中二氧化钛纳米管的阳极氧化形成机理及应用

采用电化学阳极氧化的方法,以氯化铵(NH₄Cl)水溶液为电解液,在纯钛表面制备了二氧化钛(TiO₂)纳米管。考察了制备电压、氧化时间、Cl^-浓度和钛基体的退火处理对阳极氧化过程的影响规律,探讨了在含氯离子电解液中纳米管的形成机理,并基于上述含氯离子电解液中纳米管形成机制,通过两步阳极氧化法得到无支撑纳米管薄膜。     

微含水量电解液中高管径比TiO2纳米管阵列的制备

通过阳极氧化法在微含水量为0.5wt%的NH₄F/乙二醇/H₂O酸性电解质体系中制备了管径大、高管径比的二氧化钛（TiO₂）纳米管阵列。采用SEM、XRD等测试手段对TiO₂纳米管阵列形貌及晶相进行表征,探讨了不同氧化时间、电压对纳米管阵列形貌的影响,微含水量下氧化电压可以适当增加,更容易得到规整的长纳米管阵列;通过测定样品的光电流和紫外-可见光漫反射吸收光谱,研究分析了含水量以及超声工艺对纳米管光吸收及光电流特性,微含水量下得到的纳米管阵列可见光吸收边红移至420nm,对480~700nm可见光有明显的光吸收,光电流显著增大;丙酮作为超声介质可有效去除纳米管阵列表面的集束,能进一步提高纳米管阵列的光电性能。     

水热法制备TiO2纳米管阵列

在(NH4)2TiF6的水溶液中,以铝基阳极氧化铝膜为模板,采用水热法制备了TiO2纳米管阵列. 采用场发射扫描电镜、 X射线能量色散谱及X射线光电子能谱对所得纳米管阵列进行了表征,并探讨了其形成机制. 结果表明,控制水热处理时间对制备形貌规整的纳米管阵列至关重要,较佳的水热处理时间为90 min. 采用本方法制备的纳米管阵列具有特殊的形貌,即表面的连续多孔结构和断面的不连续、分离的管状特征. 这种特殊形貌的形成是由于[TiF6]2-与阳极氧化铝模板的表面和断面具有不同的反应速率,水解产物优先在阳极氧化铝模板的表面沉积所致.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.