Pd/WO<Subscript>3</Subscript>/C nanocomposite with APTMS-functionalized tungsten oxide nanosheet for formic acid electrooxidation enhancement

A Pd/WO₃/C nanocomposite with 3-aminopropyltrimethoxysilane (APTMS)-functionalized tungsten oxide nanosheets (Pd/WO₃/C-APTMS) was synthesized and applied as the efficient anode catalyst for direct formic acid fuel cells (DFAFCs). The mechanism for synthesizing the nanocomposite is as follows: initially, [PdCl₄]^2? was assembled onto the tungsten oxide nanosheets modified with APTMS. Following this, Pd nanoparticles were reduced via traditional impregnation reduction of [PdCl₄]^2? with NaBH₄. The transmission electron microscope (TEM) images revealed that the Pd nanoparticles were uniformly dispersed on WO₃ nanosheets and were approximately 2.7 nm in size. The electrochemical test results showed that enhanced electrocatalytic activity for the formic acid oxidation reaction (FAOR) was obtained on the Pd/WO₃/C catalyst compared with Pd/C. The higher electrocatalytic activity might be attributed to the uniform distribution of Pd with smaller particles. Furthermore, it is likely that the improvement in catalytic stability for the Pd/WO₃/C catalyst is due to the hydrogen spillover effect of WO₃ particles. These results indicate that this novel Pd/WO₃/C-APTMS nanocomposite exhibits promising potential for use as an anode electrocatalyst in DFAFCs.     

Study of Au-Pd core-shell nanoparticles by using slow positron beam

Binary Au-Pd nanoparticles were synthesized by ultrasonic irradiation of solutions containing Au³⁺ and Pd²⁺ ions (the ion ratio from 0.3:0.7 to 0.9:0.1 mM) and cationic surfactant (SDS: sodium dodecyl sulfate). In each case the core-shell structure (Au core, Pd shell) was confirmed by scanning transmission electron microscopy (STEM). The mean diameters of them were all about 9 nm, and the thickness of the Pd shell depends on the ratio of Pd²⁺ and Au³⁺ ions in solution. In order to study the electronic states of core-shell nanoparticles and their dependence on shell thickness, Doppler broadening measurements were performed for Au-Pd core-shell nanoparticles by using slow positron beam technique. The ratio curves of Au-Pd particles did not match with those of pure Pd and pure Au, but a small difference in the low electron momentum region was observed among nanoparticles depending on Pd shell thickness.     

Effect of laser fluence on the size of copper oxide nanoparticles produced by the ablation of Cu target in double distilled water

Copper oxide nanoparticles produced in double distilled water at room temperature by laser ablation of the Cu target have been investigated using TEM, SEM, AFM, X-ray diffraction, photo-spectrometry and PIXE. Q-switched Nd:YAG laser operating at 1064 nm with a pulse duration of 5–6 ns was used to conduct the experiments in the fluence range of 5.73–9.87 J/cm². In each experiment, 12,000 laser pulses were used to ablate the target placed in double distilled water. Different diagnostic techniques reveal that the nanoparticles have a size between 2–55 nm and their mean size as well as the width of particle distribution increases with the laser fluence. Since no surface active material (surfactant) was added to water, the nanoparticles aggregated and settled down at the bottom of the container within a week. In addition to stable Cu₂O, the XRD spectrum also shows the presence of suboxide Cu₆₄O in the colloidal solution of nanoparticles produced in the present study.     

Stability and separation of phases in Pd and Fe exchanged NaX and NaZSM-5 catalysts in Co+H2 reaction

Pd and Fe exchanged NaX and NaZSM-5 catalysts (Pd/Fe=5) were studied. The components formed in the course of hydrogen activation at 720 K and their transformations taking place during treatments in CO+H₂ at 570 and 500 K are described. Pd_xFe, Fe²⁺ ions in octahedral and tetrahedral environments and x-iron carbide components are identified. The bimetallic component is not affected by the CO+H₂ treatment. The Fe²⁺ ions located only in tetrahedral environment were transformed into iron carbide in the X zeolite framework, while the Fe²⁺ ions of octahedral environment were also transformed in part to carbide in the ZSM-5 lattice.     

Elaboration and characterization of bimetallic nanoparticles obtained by laser ablation of Ni75Pd25 and Au75Ag25 targets in water

A YAG laser operating at the second harmonic wavelength (532 nm, 10 Hz, 8 ns and 40 mJ) was used to elaborate bimetallic nanoparticles by laser ablation of Ni₇₅Pd₂₅ and Au₇₅Ag₂₅ targets in water. TEM–EDX, UV–Vis spectroscopy and PIXE measurements were performed to obtain information on their mean sizes, size distributions and chemical composition as a function of the time of laser ablation. The surface of the laser impacted regions of the targets were characterized by RBS in order to check their composition after the laser ablation. The so-obtained bimetallic nanoparticles always show a homogeneous composition. However, while the composition of Au–Ag nanoparticles was found to be very similar to the one of the alloy target, the composition of the Ni–Pd nanoparticles can be different from the nominal composition of the alloy target. Segregation phenomena can be invoked to explain the difference between the Ni–Pd nanoparticles and the Au–Ag nanoparticles compositions obtained in the same conditions. However, an influence of chemical reactions occurring in the high pressure plasma created locally at liquid–solid interface (called ‘reactive quenching’) cannot be completely ruled out.     

Preparation of long-afterglow colloidal solution of Sr2MgSi2O7: Eu, Dy by laser ablation in liquid

We have successfully prepared a novel nanoparticle solution of Sr₂MgSi₂O₇: Eu²⁺, Dy³⁺ with afterglow properties by means of laser ablation in liquid. This process also produced by-products of different kinds, depending on the liquid used. The amount of by-product and the size of the nanoparticles were controlled by the energy density of laser ablation. The amount of by-product was reduced by a decrease in the energy density, which also decreased the particle size of the nanoparticles. The PL spectrum of the nanoparticles was the same as that of the target materials used for laser ablation. The afterglow properties deteriorated with a decrease in particle size. We concluded that an increase in specific surface area caused by a decrease in particle size resulted in the decrease of luminescent intensity.     

Laser–diode-pumped passively Q-switched Nd:NaY(WO4)2 laser with GaAs saturable absorber

A laser–diode-pumped passively Q-switched new type crystal Nd³⁺:NaY(WO₄)₂ (known as Nd:NYW) laser with GaAs semiconductor saturable absorber has been realized. The dependence of pulse repetition rate, pulse energy, pulse width, and peak power on pump power for different output coupler reflectivities are measured. The coupled rate equations are used to simulate the Q-switched process of laser, and the numerical solutions agree with the experimental results.     

Passive Q-switching of a laser-diode-pumped intracavity-frequency-doubling Nd:Nd<Superscript>3+</Superscript>:NaY(WO<Subscript>4</Subscript>)<Subscript>2</Subscript>/KTP laser with Cr<Superscript>4+</Superscript>:YAG saturable absorber

Nd³⁺:NaY(WO₄)₂, known as Nd:NYW, is a new type crystal. By using laser-diode as pump source, a passive Q-switching of intracavity-frequency-doubling Nd:NYW/KTP laser has been realized with Cr⁴⁺:YAG saturable absorber. The dependence of pulse repetition rate, pulse energy, pulse width, and peak power on incident pump power for different small-signal transmissions of Cr⁴⁺:YAG are measured. The coupled rate equations are used to simulate the Q-switched process of laser, and the numerical solutions agree with the experimental results.     

Process of direct copper plating on ABS plastics

The processes of direct copper plating on ABS plastics were investigated by atomic force microscopy (AFM), ultraviolet-visible absorption spectrometry (UV-vis) and X-ray fluorescence spectroscopy (XRF) techniques. The substrates were etched by CrO₃/H₂SO₄ solution containing Pd²⁺ ions, catalyzed by Pd/Sn colloids solution and accelerated in an alkaline solution containing copper ions. The Pd²⁺ ions in etching solution can reduce the surface roughness and enhance the colloids adsorption. The good dispersivity colloids have excellent catalysis and its UV-vis peaks broaden. After acceleration, when the stability of Cu²⁺-complex is relatively low, Sn²⁺ was oxidized by Cu²⁺ in the alkaline solution meanwhile Cu₂O can be formed. The disproportionation reaction of Cu₂O will proceed and metallic copper forms between the Pd particles, so the conductivity of ABS surface increased. The copper particles play an important role in determining the uniformity of the propagation of copper plating. The particles of copper plating layer were uniformity and fine. The atomic concentration and the thickness of copper layer were analyzed by XRF.     

Surface composition modification of tungsten higher oxide under He<Superscript>+</Superscript> ion bombardment

The surface reduction of higher oxide WO₃ under irradiation by He⁺ ions with the energies 1 and 3 keV in a high vacuum is investigated by X-ray photoelectron spectroscopy. It is found that lower WO₂ and intermediate WO _x (2 < x < 3) oxides form first in WO₃ surface layers under He⁺ ion bombardment, and with an increase in the irradiation dose metallic tungsten forms. It is shown that the degree of irradiated oxide surface metallization increases with an increase in the energy of the bombarding He⁺ ions. A comparison of WO₃ oxide surface composition modification under He⁺ and Ar⁺ ion irradiation is presented.     

Surface properties of palladium catalysts supported on ternary ZrO2–Al2O3–WOx oxides prepared by the sol–gel method: Study of the chemical state of the support

The surface properties of Pd and Pd–Pt catalysts supported on binary ZrO₂–WOx and ternary ZrO₂–Al₂O₃–WOx oxides prepared by the sol–gel method were studied. Special attention was paid to the study of the texture of the catalysts as well as the chemical state of tungstated zirconia and tungstated zirconia promoted with alumina in the palladium catalysts. The catalysts were tested in the isomerization of n-hexane and were characterized by N₂ physisorption, XRD, TPR, Raman spectroscopy, XPS and FT-IR of adsorbed pyridine. The catalysts had bimodal pore size distributions with mesopores in the range 55–70 Å and macropores of 1000 Å in diameter. The catalysts had a surface WOx coverage (4.4–6.0 W nm^?2) lower than that of the theoretical monolayer (7.0 W nm^?2). A lower acidity of the ternary ZrO₂–Al₂O₃–WOx oxide as compared to the binary ZrO₂–WOx oxide was found. Higher activity in the isomerisation of n-hexane was obtained in the Pd–Pt catalysts supported on ternary ZrAlW oxides prepared by sol–gel that is correlated with the coexistence on the surface of W⁴⁺ (WO₂) or W⁰ and W⁶⁺ (Al₂(WO₄)₃) species, ZrO₂ in the tetragonal phase and a high amount of ZrOx suboxides species in a low oxidation state (Zr³⁺ and Zr²⁺).     

Synthesis of composite gold/tin-oxide nanoparticles by nano-soldering

Composite Au–SnO₂ nanoparticles (NPs) are synthesized by nano-soldering of pure Au and SnO₂ NPs. The multi-step process involves synthesis of pure Au and SnO₂ NPs separately by nanosecond pulse laser ablation of pure gold and pure tin targets in deionized water and post-ablation laser heating of mixed solution of Au colloidal and SnO₂ colloidal to form nanocomposite. Transmission Electron Microscopy (TEM) and High-Resolution Transmission Electron Microscopy (HRTEM) were used to study the effect of laser irradiation time on morphology of the composite Au–SnO₂ NPs. The spherical particles of 4 nm mean size were obtained for 5 min of post-laser heating. Increased mean size and elongated particles were observed on further laser heating. UV–vis spectra of Au–SnO₂ nanocomposites show red shift in the plasmon resonance absorption peak and line shape broadening with respect to pure Au NPs. The negative binding energy shift of Au 4f_7/2 peak observed in X-ray Photoelectron Spectra (XPS) indicates charge transfer in the nano-soldered Au–SnO₂ between gold and tin oxide and formation of soldered nanocomposite.     

Efficient tunable laser operation of diode- pumped Yb,Tm:KY(WO4)2 around 1.9 μm

A new laser medium – Yb,Tm:KY(WO₄)₂ – for diode pumped solid state laser applications operating around 1.9 to 2.0 μm has been investigated and the main laser characteristics are presented. Diode pumping at 981 nm and around 805 nm was realised. For 981-nm pumping, the excitation occurs into Yb³⁺ ions followed by an energy transfer to Tm³⁺ions. A slope efficiency of 19% was realised. For pumping around 805 nm, the excitation occurs directly into the Tm³⁺ ions. Here a maximum slope efficiency of 52%, an optical efficiency of 40%, and output powers of more than 1 W were realised. Using a birefringent quartz plate as an intracavity tuning element, the tunability of the Yb,Tm:KY(WO₄)₂ laser in the spectral range of 1.85–2.0 μm has been demonstrated. The possibility of laser operation in a microchip cavity configuration for this material has also been shown. Received: 12 March 2002 / Revised version: 20 May 2002 / Published online: 25 September 2002 RID="*" ID="*"Corresponding author. Fax: +49-531/592-4116, E-mail: stefan.kueck@ptb.de     

Characteristics of a passively Q-switched Nd:NaY(WO4)2 laser with Cr:YAG saturable absorber

By using xenon flash lamp as pump source and Cr⁴⁺:YAG as passive Q-switcher, we have performed the Q-switched laser operation at 1.06 μm with an Nd³⁺:NaY(WO₄)₂ (known as Nd:NYW) crystal. Meanwhile, the pulse width, the single pulse energy and the repetition rate under different small-signal transmissions of Cr⁴⁺:YAG and different reflectivities of output reflector are measured, and the numerical solutions of the coupling wave rate equations agree with the experimental results.     

Optical spectroscopy of Yb/Er codoped NaY(WO4)2 crystal

Erbium and ytterbium codoped double tungstates NaY(WO₄)₂ crystals were prepared by using Czochralski (CZ) pulling method. The absorption spectra in the region 290-2000 nm have been recorded at room temperature. The Judd-Ofelt theory was applied to the measured values of absorption line strengths to evaluate the spontaneous emission probabilities and stimulated emission cross sections of Er³⁺ ions in NaY(WO₄)₂ crystals. Intensive green and red lights were measured when the sample were pumped by a 974 nm laser diode (LD), especially, the intensities of green upconversion luminescence are very strong. The mechanism of energy transfer from Yb³⁺ to Er³⁺ ions was analyzed. Energy transfer and nonradiative relaxation played an important role in the upconversion process. Photoexcited luminescence experiments are also fulfilled to help analyzing the transit processes of the energy levels.     

Excitation of high energy levels under laser exposure of suspensions of nanoparticles in liquids

Laser exposure of suspensions of nanoparticles in liquids leads to excitation of high energy levels in both liquid and nanoparticle material. The emission spectrum of the colloidal solution under exposure of a suspension metallic nanoparticles in water to radiation of a Nd:YAG laser of a picosecond range of pulse duration is discussed. Excitation of nuclear energy levels and neutron release is experimentally studied on the model system of transmutation of Hg into Au that occurs under exposure of Hg nanodrops suspended in D₂O. The proposed mechanism involves: (i) emission of X-ray photons by Hg nanoparticles upon laser exposure, leading to neutron release from D₂O, (ii) initiation of Hg → Au transmutation by the capture of neutrons. The effect of transmutation is more pronounced using ¹⁹⁶Hg isotope instead of Hg of natural isotope composition. The influence of laser pulse duration on the degree of transmutation (from fs through ns range) is discussed.     

Spectroscopic properties of Tm3+/Ho3+ co-doped NaLa(WO4)2 single crystal

Tm³⁺/Ho³⁺ co-doped NaLa(WO₄)₂ single crystal was successfully grown by the Czochralski method. The crystal was characterized by room temperature absorption spectra, fluorescence spectra around 2 μm, up-conversion fluorescence and luminescence decay measurements. Spectroscopic properties related to the laser operation around 2 μm of Ho³⁺ ions have been evaluated. The energy level scheme and energy transfer processes of Tm³⁺ and Ho³⁺ were analyzed. The obtained spectroscopic results show the crystal is a potentially host for Ho³⁺ 2 μm infrared laser.     

Electrochromic properties of tungsten oxides synthesized from aqueous solutions

Tungsten oxides are known to exhibit interesting electrochemical properties. Ion insertion (Li⁺, H⁺) within the oxide network is highly reversible. It leads to a blue coloration and WO₃ thin films can be used as electrochromic layers in display devices or smart windows. Tungsten oxide thin films can be conveniently deposited from aqueous solutions of tungstic acid. However polytungstic acids are not stable and tend to precipitate into hydrated tungsten oxide WO₃⋅2H₂O. The condensation of polytungstic species can be chemically controlled by adding foreign ions in the solution. Precipitation is no more observed in the presence of H₂O₂. Peroxopolytungstic acids are formed in which chelating [O₂]²⁻ ligands prevent the formation of an oxide network. Such solutions are specially convenient for the deposition of optically transparent thin films. Mixed oxides WO₃-MoO₃ are obtained when condensation is performed in the presence of Mo⁶⁺ cations. This paper shows how the condensation of tungstic acid can be chemically controlled and describes the electrochemical properties of the films deposited from such solutions. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

Spectroscopic properties of Yb ions in La2(WO4)3 crystal

Yb³⁺-doped La₂(WO₄)₃ single crystals were grown by the Czochralski technique. Absorption and fluorescence spectra of the crystal were recorded at the room temperature. The stimulated emission cross-sections of Yb³⁺ ions were calculated using the reciprocity method and Fuchtbauer-Ladenburg formula, respectively. The fluorescence decay curves of ²F_5/2 manifold of Yb³⁺ ions were recorded at room temperature for both crystal and powder samples. The effect of radiation trapping on the spectroscopic properties is discussed. Comparison with other Yb³⁺-doped laser crystals is made. The results show that Yb³⁺:La₂(WO₄)₃ crystal is a promising laser material.     

Synthesis of carbon supported palladium nanoparticles catalyst using a facile homogeneous precipitation-reduction reaction method for formic acid electrooxidation

A highly dispersed and ultrafine carbon supported Pd nanoparticles (Pd/C) catalyst is synthesized by a facile homogeneous precipitation-reduction reaction method. Under the appropriate pH conditions, [PdCl₄]²⁻ species in PdCl₂ solution are slowly transformed into the insoluble palladium oxide hydrate (PdO·H₂O) precipitation by heat treatment due to a slow hydrolysis reaction, which results in the generation of carbon supported PdO·H₂O nanoparticles (PdO·H₂O/C) sample with the high dispersion and small particle size. Consequently, a highly dispersed and ultrafine Pd/C catalyst can be synthesized by PdO·H₂O → Pd⁰ in situ reduction reaction path in the presence of NaBH₄. As a result, the resulting Pd/C catalyst possesses a significantly electrocatalytic performance for formic acid electrooxidation, which is attributed to the uniformly sized and highly dispersed nanostructure.