Exciton-polariton state in nanocrystalline SiC films

We studied the features of optical absorption in the films of nanocrystalline SiC (nc-SiC) obtained on the sapphire substrates by the method of direct ion deposition. The optical absorption spectra of the films with a thickness less than ~500 nm contain a maximum which position and intensity depend on the structure and thickness of the nc-SiC films. The most intense peak at 2.36 eV is observed in the nc-SiC film with predominant 3C-SiC polytype structure and a thickness of 392 nm. Proposed is a resonance absorption model based on excitation of exciton polaritons in a microcavity. In the latter, under the conditions of resonance, there occurs strong interaction between photon modes of light with λ_ph=521 nm and exciton of the 3С polytype with an excitation energy of 2.36 eV that results in the formation of polariton. A mismatch of the frequencies of photon modes of the cavity and exciton explains the dependence of the maximum of the optical absorption on the film thickness.     

Comparative study on structural and optical properties of ZnO thin films prepared by PLD using ZnO powder target and ceramic target

Zinc oxide thin films have been obtained in O₂ ambient at a pressure of 1.3 Pa by pulsed laser deposition (PLD) using ZnO powder target and ceramic target. The effect of temperature on structural and optical properties of ZnO thin films was investigated systematically by XRD, SEM, FTIR and PL spectra. The results show that the best structural and optical properties can be achieved for ZnO thin film fabricated at 700 °C using powder target and at 400 °C using ceramic target, respectively. The PL spectrum reveals that the efficiency of UV emission of ZnO thin film fabricated by using powder target is low, and the defect emission of ZnO thin film derived from Zn_i and O_i is high.     

Structure,optical spectroscopy and dispersion parameters of ZnGa2Se4 thin films at different annealing temperatures

Thin films of ZnGa₂Se₄ were deposited by thermal evaporation method of pre-synthesized ingot material onto highly cleaned microscopic glass substrates. The chemical composition of the investigated compound thin film form was determined by means of energy-dispersive X-ray spectroscopy. X-ray diffraction XRD analysis revealed that the powder compound is polycrystalline and the as-deposited and the annealed films at T_a = 623 and 673 K have amorphous phase, while that annealed at T_a = 700 K is polycrystalline with a single phase of a defective chalcopyrite structure similar to that of the synthesized material. The unit-cell lattice parameters were determined and compared with the reported data. Also, the crystallite size L, the dislocation density δ and the main internal strain ε were calculated. Analyses of the AFM images confirm the nanostructure of the prepared annealed film at 700 K. The refractive index n and the film thickness d were determined from optical transmittance data using Swanepoel's method. It was found that the refractive index dispersion data obeys the single oscillator model from which the dispersion parameters were determined. The electric susceptibility of free carriers and the carrier concentration to the effective mass ratio were determined according to the model of Spitzer and Fan. The analysis of the optical absorption revealed both the indirect and direct energy gaps. The indirect optical gaps are presented in the amorphous films (as-deposited, annealed at 623 and 673 K), while the direct energy gap characterized the polycrystalline film at 700 K. Graphical representations of ε₁, ε₂, tan δ, ? Im[1/ε*] and ? Im[(1/ε* + 1)] are also presented. ZnGa₂Se₄ is a good candidate for optoelectronic and solar cell devices.     

Optical properties of PMN–PT thin films prepared using pulsed laser deposition

(1 ? x)Pb(Mg_1/3Nb_2/3)O₃–xPbTiO₃ (PMN–PT) thin films have been deposited on quartz substrates using pulsed laser deposition (PLD). Crystalline microstructure of the deposited PMN–PT thin films has been investigated with X-ray diffraction (XRD). Optical transmission spectroscopy and Raman spectroscopy are used to characterize optical properties of the deposited PMN–PT thin films. The results show that the PMN–PT thin films of perovskite structure have been formed, and the crystalline and optical properties of the PMN–PT thin films can be improved as increasing the annealing temperature to 750 °C, but further increasing the annealing temperature to 950 °C may lead to a degradation of the crystallinity and the optical properties of the PMN–PT thin films. In addition, a weak second harmonic intensity (SHG) has been observed for the PMN–PT thin film formed at the optimum annealing temperature of 750 °C according to Maker fringe method. All these suggest that the annealing temperature has significant effect on the structural and optical properties of the PMN–PT thin films.     

Synthesis of CdS nanostructures using template-assisted ammonia-free chemical bath deposition

CdS micro- and nano-structures (micro/nanotubes and nanostructured films) were obtained by ammonia-free chemical bath deposition using polymer templates (ion track-etched polycarbonate membranes and poly(styrene-hydroxyethyl methacrylate) nanosphere arrays). The semiconductor structures were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), optical absorption, photoluminescence and electrical measurements. The diameters of CdS tubes are between 300 nm and few microns and the lengths are up to tens of micrometers. The SEM images prove that the CdS films are nanostructured due to the deposition on the polymer nanosphere arrays. For both CdS structures (tubes and films) the XRD patterns show a hexagonal phase. The optical studies reveal a band gap value of about 2.5?2.6 eV and a red luminescence at ～1.77 eV. A higher increase of conductivity is observed for illuminating the CdS nanostructured film when compared to the simple semiconductor film. This is a consequence of the periodic patterning induced by the polymer nanosphere array.     

Annealing temperature dependent on structural,optical and electrical properties of indium oxide thin films deposited by electron beam evaporation method

In the present work the influence of annealing temperature on the structural and optical properties of the In₂O₃ films deposited by electron beam evaporation technique in the presence of oxygen was studied. The deposited films were annealed from 350 to 550 °C in air. The chemical compositions of In₂O₃ films were carried out by X-ray photoelectron spectroscopy (XPS). The film structure and surface morphologies were investigated as a function of annealing temperature by X-ray diffraction (XRD) and atomic force microscopy (AFM). The structural studies by XRD reveal that films exhibit preferential orientation along (2 2 2) plane. The refractive index (n), packing density and porosity (%) of films were arrived from transmittance spectral data obtained in the range 250–1000 nm by UV–vis-spectrometer. The optical band gap of In₂O₃ film was observed and found to be varying from 3.67 to 3.85 eV with the annealing temperature.     

Effect of GZO thickness and annealing temperature on the structural,electrical and optical properties of GZO/Ag/GZO sandwich films

The GZO/Ag/GZO sandwich films were deposited on glass substrates by RF magnetron sputtering of Ga-doped ZnO (GZO) and ion-beam sputtering of Ag at room temperature. The effect of GZO thickness and annealing temperature on the structural, electrical and optical properties of these sandwich films was investigated. The microstructures of the films were studied by X-ray diffraction (XRD). X-ray diffraction measurements indicate that the GZO layers in the sandwich films are polycrystalline with the ZnO hexagonal structure and have a preferred orientation with the c-axis perpendicular to the substrates. For the sandwich film with upper and under GZO thickness of 40 and 30 nm, respectively, it owns the maximum figure of merit of 5.3 × 10⁻² Ω⁻¹ with a resistivity of 5.6 × 10⁻⁵ Ω cm and an average transmittance of 90.7%. The electrical property of the sandwich films is improved by post annealing in vacuum. Comparing with the as-deposited sandwich film, the film annealed in vacuum has a remarkable 42.8% decrease in resistivity. The sandwich film annealed at the temperature of 350 °C in vacuum shows a sheet resistance of 5 Ω/sq and a transmittance of 92.7%, and the figure of merit achieved is 9.3 × 10⁻² Ω⁻¹.     

Nonlinear optical properties of erbium doped zinc oxide (EZO) thin films

Undoped and Erbium (Er) doped zinc oxide (EZO) thin films were deposited on glass substrate by sol–gel method using spin coating technique with different doping concentration. EZO films were characterized using X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), UV–VIS-NIR transmission and single beam z scan method under illumination of frequency doubled Nd:YAG laser. The deposited films were found to be well crystallized with hexagonal wurtzite structure having a preferential growth orientation along the ZnO (002) plane. A blue-shift was observed in the band gap of EZO films with increasing Er concentration. All the films exhibited a negative value of nonlinear refractive index (n₂) at 532 nm which is attributed to the two photon absorption and weak free carrier absorption. Third order nonlinear optical susceptibility, χ⁽³⁾ values of EZO films were observed in the remarkable range of 10^? 6 esu. EZO (0.4 at.%) sample was found to be the best optical limiter with limiting threshold of 1.95 KJ/cm².     

Optical properties of Cr/Fe(t)/MgO (0 0 1) thin films

In this work we report on the optical properties of single-crystalline iron thin films. For this, Cr-capped Fe films with thickness, t, in the range 30–300 Å were prepared on MgO (0 0 1) by DC magnetron sputtering, and then studied by optical absorption technique within the range from 1.0 to 3.6 eV. All measurements were carried out at room temperature using a fiber optics spectrophotometer. The intensity of the transmitted light decreases with increasing film thickness. The optical constants of the films are deduced from a model that considers the transmission of light by two absorbing films on an absorbing substrate. The absorption coefficient of the Fe films is also calculated from the transmission data. The absorption spectra show the following characteristics: (i) two large absorption peaks centered at about 1.20 and 2.65 eV; and (ii) a sharp step near 1.40 eV. These structures are associated with conventional interband transitions of the iron film.     

Influence of γ-irradiation on the optical parameters of 4-tricyanovinyl-N,N-diethylaniline thin films

Thin films of 4-tricyanovinyl-N,N-diethylaniline (TCVA) were prepared by thermal evaporation technique. The spectral and the optical parameters have been investigated by using the spectrophotometric measurements of both transmittance and reflectance at normal incidence of light in the wavelength range 200–2500 nm. The effect of γ-irradiation on the optical parameters was investigated. It was observed that the increase in γ-irradiation dose caused an increase in the value of absorption index and a shift in the spectrum towards higher wavelengths. Therefore, the value of the optical band gap has decreased from 1.45 eV for as-deposited film to 1.39 eV for film exposed to γ-ray dose of 150 kGy and Urbach tail increased. On the other hand, the dispersion parameters of TCVA films were increased with the increase of the irradiation dose.     

Properties of Bi2O3 thin films prepared via a modified Pechini route

Thin bismuth oxide films have been prepared by a modified Pechini route on glass substrate and annealed at temperatures ranging between 400 °C and 700 °C using bismuth nitrate as raw material. The thin films were then characterized for structural, surface morphological, optical and electrical properties by means of X-ray diffraction (XRD), Atomic force microscopy (AFM), scanning electron microscopy (SEM), optical absorption and d.c. two-probe, respectively. Structural investigations indicated that as-prepared bismuth oxide films were polycrystalline and multiphase, and annealing temperatures played a key role in the composition and optical properties of these films. AFM and SEM images revealed well defined particles which are highly influenced by annealing temperatures. The optical studies showed a direct band gap which varied with annealing temperatures between 3.63 eV and 3.74 eV. The electrical measurement showed that the electrical resistivity increased with annealing temperatures and the films were typical semiconductors. As catalyst, bismuth oxide films annealed at 550 °C had the best photocatalytic performance for photodegradation of methyl orange.     

The annealing effect on structural,optical and photoelectrical properties of CuInS2/In2S3 films

Successive Ionic Layer Adsorption and Reaction (SILAR) technique was used to deposit the CuInS₂/In₂S₃ multilayer thin film structure at room temperature. The as-deposited film was annealed at 100, 200, 300, 400 and 500 °C for 30 min in nitrogen atmosphere and the annealing effect on structural, optical and photoelectrical properties of the film was investigated. X-ray diffraction (XRD) and optical absorption spectroscopy were used for structural and optical studies. Current–Voltage (I–V) measurements were performed in dark environment and under 15, 30 and 50 mW/cm² light intensity to investigate the photosensitivity of the structure. Also, the electrical resistivity of the film was determined in the temperature range of 300–470 K. It was found that annealing temperature drastically affects the structural, optical and photoelectrical properties of the CuInS₂/In₂S₃ films.     

Optical properties of nanostructured InSe thin films

Thin films of InSe were prepared by thermal evaporation technique. The as-deposited films have nano-scale crystalline nature and the annealing enhanced the degree of crystallinity. The optical properties of nanocrystalline thin films of InSe were studied using spectrophotometric measurements of transmittance, T, and reflectance, R, at normal incidence of light in the wavelength range 200–2500 nm. The optical constants (refractive index, n, and absorption index, k) were calculated using a computer program based on Murmann's exact equations. The calculated optical constants are independent of the film thickness. The optical dispersion parameters have been analysed by single oscillator model. The type of transition in InSe films is indirect allowed with a value of energy gap equals to 1.10 eV, which increased to 1.23 eV upon annealing.     

The production of Sr hexaferrite thick films by screen printing

Hydrothermally synthesised Sr hexaferrite (HT-SrM) powder with a distinct plate-like shape and conventional Sr hexaferrite (c-SrM) powder were used to screen print SrM thick films on alumina substrates. In the case of the HT-SrM thick films, a very strong perpendicular magnetic anisotropy has been observed with remanence values of up to 42±2 J/T kg for the perpendicular direction and 15±1 J/T kg for the in-plane direction, and with coercivities of around 159±8 kA/m for both directions when fired at 1300°C. When fired at 1150°C, the remanences were 49±2 and 27±2 J/T kg for the two directions with a higher coercivity of 247±8 kA/m for both directions. The SEM micrographs showed that the platelet grains in the printed films lay with their flat surfaces on the substrate and XRD results revealed that the c-axis of the grains oriented perpendicularly to the film surface. The (0 0 8) plane, which is, for a random oriented sample, a very weak peak, appeared as the strongest in the XRD pattern for the films. EDX and XRD studies indicated significant reaction at the interfaces between the film and the substrate when the sintering temperature was raised to 1350°C.For the SrM thick films obtained from planetary milled ultrafine Sr hexaferrite and conventional Sr hexaferrite powder, a slight in-plane anisotropy could be observed with a coercivity of 318±8 kA/m.     

High-energy ion induced physical and surface modifications in antimony sulphide thin films

Sb₂S₃ thin films prepared by electrodeposition on indium tin oxide coated glass substrate were irradiated with 150 MeV Ni¹¹⁺ ions for various fluence in the range of 10¹¹–10¹³ ions/cm². The modifications in the structure, surface morphology and optical properties have been studied as a function of ion fluence. X-ray diffraction (XRD) analysis indicates a shift in the (2 4 0) peak position towards lower diffraction angle and a decrease in grain size with increase in ion fluence. Presence of microcracks due to irradiation induced grain splitting effect has been observed from the SEM micrograph at higher ion fluence. The optical absorbance spectrum revealed a shift in the fundamental absorption edge and the band gap energy increased from a value of 1.63 eV for as-deposited films to 1.80 eV for the films irradiated with 10¹³ ions/cm².     

Optical absorption and dispersion characterizations of CuGaSe2 thin films prepared by flash evaporation technique

Thin films of CuGaSe₂ have been prepared by flash evaporation technique. The optical properties of the prepared films were investigated using spectrophotometric measurements of the transmittance and reflectance at normal incidence of light in the wavelength range from 400 to 2500 nm. The optical constants as refractive index, n, and absorption index, k, were calculated and found to be independent of film thickness in the range of the film thickness 132–423 nm. The analysis of the photon energy against the absorption coefficient showed three direct optical transitions (one of them is allowed while the others are forbidden). This direct transition was ascribed to the crystal field and spin orbital splitting of the upper most valence band. The crystal field and spin orbital splitting of CuGaSe₂ were found to be ? 0.15 eV and 0.45 eV, respectively. The dispersion of the refractive index is discussed in terms of the single oscillator Wemple–DiDomenico (WD) model. The single oscillator energy (E_o), the dispersion energy (E_d), the high frequency dielectric constant (ε_∞), the lattice dielectric constant (ε_L) and the ratio of free charge carrier concentration to the effective mass (N / m*) were estimated. The capacitance–voltage measurements of CuGaSe₂/p-Si heterojunction showed that the diode is abrupt junction diode. The carrier concentration and the built-in voltage were estimated. The current–voltage characteristics of the device under illumination were investigated and photovoltaic properties of the device were evaluated.     

Synthesis,growth and characterization of a semiorganic nonlinear optical single crystal: L-Valine cadmium bromide

A semiorganic nonlinear optical material L-valine cadmium bromide was synthesized and single crystal grown from an aqueous solution by the method of slow evaporation technique at room temperature. The grown crystal was characterized by Powder X-ray diffraction and FT IR studies. The LVCB crystallizes in monoclinic system with cell parameters a = 10.144(2) Å, b = 5.54(1) Å, c = 12.07(2) Å, β = 109.115(2)° with space group P₂₁. Thermal behavior and stability of crystal were studied using thermogravimetric analyses (TGA) and differential thermal analysis (DTA) techniques. The suitability of this material for NLO application was studied by optical absorption studies and second harmonic generation (SHG) efficiency measurement by Kurtz–Perry powder method.     

Epitaxial ZnO thin films grown by pulsed electron beam deposition

In this work, the pulsed electron beam deposition method (PED) is evaluated by studying the properties of ZnO thin films grown on c-cut sapphire substrates. The film composition, structure and surface morphology were investigated by means of Rutherford backscattering spectrometry, X-ray diffraction and atomic force microscopy. Optical absorption, resistivity and Hall effect measurements were performed in order to obtain the optical and electronic properties of the ZnO films. By a fine tuning of the deposition conditions, smooth, dense, stoichiometric and textured hexagonal ZnO films were epitaxially grown on (0001) sapphire at 700 °C with a 30° rotation of the ZnO basal plane with respect to the sapphire substrate. The average transmittance of the films reaches 90% in the visible range with an optical band gap of 3.28 eV. Electrical characterization reveals a high density of charge carrier of 3.4 × 10¹⁹ cm^?3 along with a mobility of 11.53 cm²/Vs. The electrical and optical properties are discussed and compared to ZnO thin films prepared by the similar and most well-known pulsed laser deposition method.     

Effect of laser incident energy on the structural,morphological and optical properties of Cu2ZnSnS4 (CZTS) thin films

The polycrystalline Cu₂ZnSnS₄ (CZTS) thin films have been prepared by pulsed laser deposition (PLD) method at room temperature. The laser incident energy was varied from 1.0 at the interval of 0.5–3.0 J/cm². The effect of laser incident energy on the structural, morphological and optical properties of CZTS thin films was studied by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and optical absorption. The studies reveal that an improvement in the structural, morphological and optical properties of CZTS thin films with increasing laser incident energy up to 2.5 J/cm². However, when the laser incident energy was further increased to 3.0 J/cm², leads to degrade the structural, morphological and optical properties of the CZTS thin films.     

Effect of annealing on structure and optical properties of Ga5Se95 films

To investigate the effect of annealing on the structural and optical properties of a binary compound Ga₅Se₉₅, thin films of Ga₅Se₉₅ have been deposited on quartz substrates at room temperature by the thermal evaporation technique. X-ray diffraction patterns showed that the films before and after annealing at 573 K have polycrystalline texture and exhibit tetragonal structure. The dependences of the optical constants, the refractive index n and extinction coefficient k were studied in the spectral range of 200 nm to 2500 nm. The normal dispersion of the refractive index of the films could be described using the Wemple–DiDomenco single-oscillator model. Analysis of absorption index data reveals that as-deposited Ga₅Se₉₅ films has indirect transitions with optical energy gap of 1.685 eV.