离子液体型表面活性剂研究

以1-甲基咪唑为原料, 制备了6个常规离子液体: 1-正丁基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[bmim][BF₄]及[bmim][PF₆])、1-正己基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[hmim][BF₄]及[hmim][PF₆])、1-正十六烷基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[C₁₆mim][BF₄]及[C₁₆mim][PF₆])和4个功能化离子液体: 1-(2-羟乙基)-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[2-hemim][BF₄]及[2-hemim][PF₆])、1-乙氧羰基甲基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[eocmmim][BF₄]及[eocmmim][PF₆]). 研究了这两类离子液体的一些物理性能, 旨在挖掘离子液体在香料香精化妆品工业中的应用价值. 分别检测了它们与一般溶剂的互溶性, 并测定了它们的表面张力和发泡性能, 实验结果表明, 仅[C₁₆mim][BF₄]和[C₁₆mim][PF₆]具有发泡性能, 发泡力分别为68和120 mm.     

离子液体中Fe电极界面结构的SERS光谱研究

采用高灵敏度的表面增强拉曼光谱(SERS)技术, 结合不同长度的探针分子, 通过电化学调控研究了Fe电极在离子液体中的表面增强因子、零电荷电位、界面吸附及界面双电层结构. 利用壳层隔绝纳米粒子增强拉曼光谱(SHINERS)技术提高表面吸附物种的拉曼信号, 降低高浓度本体的信号干扰, 研究了1-丁基-3-甲基咪唑四氟硼酸盐([BMIm]BF₄)离子液体本身在Au@SiO₂修饰的Fe电极表面的吸附行为. 结果表明,[BMIm]BF₄在Au@SiO₂修饰的Fe电极表面的吸附行为随电位变化而变化. 在-1.3 V以正区间, 咪唑阳离子以垂直吸附为主, 随电位负移逐渐倾斜甚至平躺吸附于电极表面; 当电位负至-2.3 V, 咪唑阳离子还原成卡宾. 再分别以不同分子长度的硫氰根(SCN^-)和4-氰基吡啶(4-CNPy)为探针分子, 发现SCN^-在[BMIm]BF₄中以N端吸附在纯Fe电极上, 三键频率随电位变化的速率, 即Stark系数为17 cm^-1/V; 4-CNPy以吡啶环上的N垂直吸附于Fe电极上, 频率保持不变, 即Stark系数接近零. 以上结果表明, 在离子液体中电极界面双电层与水体系的差别较大, 电位主要分布在电极紧密层中, 几乎无分散层存在. 此外, 还计算了[BMIm]BF₄中Fe电极的增强因子约为1.5×10².     

1-烷基-3-甲基咪唑系列室温离子液体表面张力的研究

合成了系列1-烷基-3-甲基咪唑四氟硼酸盐([C_2～7mim]BF₄)及六氟磷酸盐([C_4～7mim]PF₆)室温离子液体, 并通过核磁氢谱、红外光谱、质谱等手段对其进行了结构表征; 采用Wilhelmy白金板法, 在293～338 K范围内测定了离子液体的表面张力, 测试结果显示, 同类离子液体表面张力γ随温度的升高而线性下降, 同种离子液体的表面张力呈现出较宽的变化范围, 如293 K下, 表面张力值从[C₂mim]BF₄的50.4 mJ/m²到[C₇mim]BF₄的36.1 mJ/m². 最后对离子液体的表面性能进行了讨论.     

高压静电纺丝法制备P(VDF-HFP)聚合物电解质

以高压静电纺丝法制备了具有微孔结构的偏氟乙烯-六氟丙烯共聚物[P(VDF-HFP)]无纺布膜, 吸附离子液体3-乙基-1-甲基咪唑鎓四氟硼酸盐(EMIBF₄)后成为凝胶聚合物电解质, 其室温离子电导率达到8.43 mS•cm^－1, 初始热失重温度超过300 ℃. 以其为聚合物电解质的活性碳电极双电层电容器具有较好的电化学性能, 1.0 mA•cm^－2恒流充放电500次循环后仍保持 90.67 F•g^－1的比容量, 容量保持率为96.86%.     

离子液体/乙烯-醋酸乙烯共聚物复合材料的制备与性能

分别将离子液体三正丁基甲铵(双三氟甲磺酰)亚胺盐([TBMA][NTf₂])和1-乙基-3-甲基咪唑四氟硼酸盐([EMIM][BF₄])与乙烯-醋酸乙烯共聚物弹性体(EVM)熔融共混制备复合材料,研究了离子液体与EVM的相容性及抗静电性能。 样品宏观透明性和SEM测试结果显示,[TBMA][NTf₂]与EVM具有较好的相容性,相应的EVM/[TBMA][NTf₂]复合材料的抗静电效果更好;热重分析(TGA)结果表明,[TBMA][NTf₂]促进EVM热解,而[EMIM][BF₄]对EVM的热稳定影响较小。 室温下在EVM中填加[TBMA][NTf₂]的共混物表现出较好的柔性,当[TBMA][NTf₂]质量分数为20%时,EVM/[TBMA][NTf₂]复合材料的模量为0.58 MPa,断裂伸长率可达到2997%。     

反气相色谱法表征离子液体1-己基-3-甲基咪唑四氟硼酸盐的热力学参数

采用反气相色谱法(IGC)表征了离子液体(IL)1-己基-3-甲基咪唑四氟硼酸盐([HMIM]BF₄)在343.15~373.15 K温度范围内的热力学参数.使用了一系列不同化学结构的探针分子测定[HMIM]BF₄与溶剂之间的相互作用力.根据探针分子的保留时间计算得到探针分子与[HMIM]BF₄之间的Flory-Huggins相互作用参数、摩尔吸附焓、无限稀释摩尔混合焓、摩尔蒸发焓、无限稀释活度系数以及[HMIM]BF₄的溶解度参数.结果表明,n-C₆、n-C₇、n-C₈、n-C₉、乙醚、四氢呋喃、苯、环己烷为[HMIM]BF₄的不良溶剂;甲苯、间二甲苯、甲醇、乙醇、二氯甲烷、四氯化碳、氯仿、丙酮、乙酸乙酯、乙酸甲酯为[HMIM]BF₄的良溶剂.运用外推法得到了[HMIM]BF₄在室温(298.15K)时的溶解度参数为23.70 (J·^-3)^0.5.实验结果证明反气相色谱法是一种简便准确的获得离子液体热力学参数的方法.获得的热力学参数体现了这种离子液体与探针分子之间的相互作用力.本研究为离子液体的进一步应用提供了参考.     

先锋褐煤在离子液体中温和加氢转化研究

对先锋褐煤在离子液体1-丁基-3-甲基咪唑四氟硼酸盐([Bmim]BF₄)中于温和条件下(350 ℃)的加氢液化行为进行了研究.主要考察了催化剂FeS、ZnCl₂、AlCl₃和FeCl₃对先锋褐煤在离子液体[Bmim]BF₄中液化性能的影响规律,并对液化产物进行了红外光谱分析.研究发现,先锋褐煤在离子液[Bmim]BF₄、催化剂和四氢萘(THN)作用下具有较好的液化性能.在350 ℃、[Bmim]BF₄和ZnCl₂作用下,先锋褐煤的液化产物产率为66.2%,主要的液化产物为四氢呋喃可溶物(THFS)、四氢呋喃不溶而N-甲基吡咯烷酮可溶的产物(NS).液化产物的红外光谱分析结果表明,催化剂的种类显著影响液化产物的分布和结构.     

含磷活性炭作为双电层电容器电极材料的电化学性能

采用磷酸活化和磷酸改性制备了不同种类的含磷活性炭,采用元素分析、X射线光电子能谱(XPS)和氮气吸附等手段分析了活性炭的元素含量、表面化学性质和孔隙结构,采用恒电流充放电、循环伏安和交流阻抗分别考察了活性炭在KOH和H₂SO₄电解质溶液中作为超级电容器电极材料的电化学性能,采用自由截距多元线性回归拟合统计分析研究了活性炭电极比电容量的影响因素,应用三电极体系分析了磷元素对活性炭电化学性能的影响机理。研究结果表明,活性炭掺杂的磷引入了赝电容,提高了活性炭电极的比电容量,磷元素含量为5.88%(w)的活性炭的比电容量在0.1 A·g^-1下达到185 F·g^-1。统计分析结果显示,活性炭的中孔有利于电解质离子向微孔内的扩散。在6 mol·L^-1 KOH电解质溶液中,孔径在1.10-1.61 nm、2.12-2.43nm及3.94-4.37 nm范围内是电解质离子在活性炭孔隙内部形成双电层的主要场所;在1 mol·L^-1 H₂SO₄电解质溶液中,孔径在0.67-0.72 nm范围内有利于双电层电容的形成。     

自愈合离子凝胶的制备及传感测试

制备可自愈合离子凝胶及测试其应变和湿度感应,可用作本科新生的普通化学实验,经拓展内容后也适用于应用化学、高分子化学和材料科学与工程等相关专业本科生的综合实验。实验采用自由基聚合法将1-乙烯基-3-丁基咪唑四氟硼酸盐（[VBIm][BF₄]）制备成交联聚合物凝胶（PIL）,1-丁基-3-甲基咪唑四氟硼酸盐（[BMIm][BF₄],IL）充盈其中作为溶剂和添加剂。该PIL/IL离子凝胶中存在游离态的离子液体,具有良好的导电性,可对应变和湿度变化产生响应;同时,因具有较强离子键相互作用,该离子凝胶具有自愈合能力,可重复使用。     

离子液体对木瓜蛋白酶催化特性的影响

研究了以1-丁基-3-甲基咪唑、四乙基铵及N-乙基吡啶为阳离子, 配以多种阴离子(H₂PO₄^-, ClO₄^-, HSO₄^-, CH₃COO^-, Cl^-, Br^-, NO₃^-, SCN^-, BF₄^-, PF₆^-)的离子液体对木瓜蛋白酶催化N-苯甲酰-L-精氨酸乙酯(BAEE)水解的活性及热稳定性的影响. 通过分析含离子液体体系中木瓜蛋白酶的水解活性和热力学失活参数, 发现该酶活性及稳定性与离子液体的Kosmotropicity性质无关. 因此, 离子的Hofmeister效应并不适合解释离子液体对木瓜蛋白酶催化特性的影响规律. 当以BF₄^-为阴离子, 改变阳离子结构时, 仅[BMIm][BF₄]可提高酶活性, 其它含官能团的咪唑类离子液体则降低酶活性, 但大部分离子液体明显提高木瓜蛋白酶的热稳定性. 在所研究的离子液体中, 基于PF₆^-或BF₄^-阴离子的离子液体可提高木瓜蛋白酶的活性及其热稳定性. 在含[BMIm][PF₆]介质中, 木瓜蛋白酶的水解活性最高; 在含[HOEtMIm][BF₄]介质中其热稳定性最好.     

咪唑类离子液体混合物吸收CO2性能研究

结合常规离子液体和功能型离子液体在吸收CO₂方面的优势,将两类咪唑类离子液体进行混合,对其吸收CO₂的效果和再生性能进行了实验研究。结果表明,两类咪唑类离子液体混合后流动性明显改善,与CO₂接触气液传质顺畅;常规离子液体[bmim][BF₄]和[bmim][Tf₂N]与胺功能型离子液体[NH₂e-mim][BF₄]混合物较单一的离子液体吸收CO₂的量大,[bmim][CH₃CO₂]与[NH₂e-mim][BF₄]混合后较单一的[bmim][CH₃CO₂]吸收量有明显的减低;随着常规咪唑类离子液体阳离子碳链增长,混合离子液体吸收CO₂的效果变强;与胺乙基功能型离子液体混合吸收CO₂时,阴离子为[Tf₂N]的常规咪唑类离子液体要比阴离子为[BF₄]的吸收效果好;离子液体混合物吸收CO₂后经再生循环利用10次,混合物质量基本不变,循环使用后吸收CO₂性能为初始吸收性能的75%~85%。     

A SEM–EDX study of highly stable supported liquid membranes based on ionic liquids

This work evaluates the operational stability of six different supported liquid membranes (SLMs) based on ionic liquids (ILs). [bmim⁺][PF₆⁻]_, [bmim⁺][BF₄⁻] and [bmim⁺][NTf₂⁻] were used as supporting phase in Nylon^® and Mitex^® membranes. Scanning electron microscopy (SEM) combined with energy dispersive X-ray (EDX) analysis was used to characterize the membrane surface morphologically and examine the global chemical composition of the membranes and the distribution of the ILs within them.

Study of the freshly impregnated membranes showed that, in all cases, the ILs were homogeneously distributed, mostly filling the pores of the membranes although, in some cases, a small amount of excess of IL was located on the external membrane surface. Stability tests were performed by keeping the respective impregnated membranes immersed for a week in a diffusion cell including two independent compartments and using n-hexane/n-hexane as the respective feed and receiving phases. The SEM–EDX study of membranes after continuous operation showed that the ILs were still retained within the membrane pores and only small losses of the IL initially located on the external surface were observed. These observations are in complete agreement with the ionic losses determined by mass balance.     

EMIM离子液体离子簇模型的量子化学计算

以1-乙基-3-甲基咪唑(EMIM)卤化物、氟硼酸盐、三溴化物和二碘溴酸盐、氯铝酸和溴铝酸盐等不同种类EMIM离子液体为研究对象,对多阳离子、多阴离子的离子簇模型进行了量子化学计算研究.首先在B3LYP/6-311++G(d, p)水平上(I使用6-311G(d, p)基组)对{[EMIM]X_n}^(n-1)- (X = Cl, Br, I, BF₄, AlCl₄, AlBr₄, Br₃, IBrI, FHF; n = 2, 3)和{[EMIM]₂X_n'}^(n'-2)- (n' = 3, 4, 5)离子簇进行构型优化,并对卤化物和氟硼酸盐进行了振动光谱计算.结果表明所采用理论模型在键长、键角等结构参数及红外振动光谱方面均与实验结果符合较好.同时对不同离子簇模型中阴、阳离子间相互作用能与实验熔点之间的关系进行了研究,发现采用{[EMIM]₂X_n'}^(n'-2)--模型时EMIM离子液体实验熔点与阴、阳离子间相互作用能之间呈现近线性关系.     

Preparation and Supercapacitive Properties of Fe2O3/Active Carbon Nanocomposites

Fe₂O₃/active carbon(Fe₂O₃/AC) nanocomposites were readily fabricated by pyrolyzing Fe³⁺ impregnated active carbon in a nitrogen atmosphere. The as-prepared composites were studied by X-ray powder diffraction(XRD), X-ray photoelectron spectroscopy(XPS) and transmission electron microscopy(TEM). The capacitive property of the composites was investigated by cyclic voltammetry(CV) and galvanostatic charge-discharge test. Physical characterizations show that the γ-Fe₂O₃ fine grains dispersed in the AC well, with a mean size of 21.24 nm. Electrochemical tests in 6 mol/L KOH solutions indicate that the as-prepared nanocomposites exhibited improved capacitive properties. The specific capacitance(SC) of Fe₂O₃/AC nanocomposites was up to 188.4 F/g that was derived from both electrochemical double-layer capacitance and pseudo-capacitance, which was 78% larger than that of pristine AC. A symmetric capacitor with Fe₂O₃/AC nanocomposites as electrode showed an excellent cycling stability. The SC was only reduced by a factor of 9.2% after 2000 cycles at a current density of 1 A/g.     

Density and surface tension of binary mixtures of 1-ethyl-3-methylimdazolium nitrate with alcohols

New experimental data of densities and surface tensions are presented for the binary mixtures of the ionic liquid 1-ethyl-3- methyl imidazolium nitrate（[EMIM]NO₃） with methanol and ethanol.Measurements were performed at 298.15 K and atmospheric pressure,covering the whole composition range.Excess molar volumes V^E and the surface tension deviations Sy have been determined.For the excess molar volumes of binary mixture,there is a region of negative V^E at low IL mole fraction,passing through a minimum and then V^E increases and becomes positive,showing maximum at higher IL mole fraction.It is shown that the surface tension deviations Sy of[EMIM]NO₃ + methanol system are positive but those of[EMIM]NO₃ + ethanol system are negative over the entire mole fraction range.     

Crystal Structures,Thermal Analysis and Electrochemical Behaviors of Functionalized Pyridinium Ionic Liquids Comprising One 1-Ethyl Acetate Group

Pyridinium ionic liquids(ILs, 1-ethyl acetate pyridinium hexfluorophosphate[EAPy][PF₆] and 1-ethyl acetate-3-methyl pyridinium hexfluorophosphate[EAMPy][PF₆]), were synthesized by a two-step process involving introduction of one ethyl acetate group and anion metathesis. Colorless single crystals of the two ILs were initially obtained using the solvent-evaporation method in mixed solvents. Single-crystal X-ray diffraction was used to determine the crystal structures.[EAPy][PF₆] crystallizes in the monoclinic space group C2/c with a=2.2748(16) nm, b=0.6204(4) nm, c=1.8552(12) nm and Z=8, whereas[EAMPy][PF₆] crystallizes in the orthorhombic space group P2₁2₁2₁ with a=0.7126(17) nm, b=1.2792(3) nm, c=1.5327(3) nm and Z=4. The structure of[EAPy][PF₆] contains double zigzag chains formed by alternately pairing large organic cations with the octahedral anions of[P1F₆]^- or[P2F₆]^-. The[P1F₆]^- and[P2F₆]^- anions occupy respectively two distinct crystallographic sites in crystal packing models. The structure of[EAMPy][PF₆] includes ladder-type chains constructed through pairing pyridinium cations with inorganic anions of[PF₆]^-. The[PF₆]^- anion in[EAMPy][PF₆] shows a distorted octahedron structure and is sandwiched by ethyl acetate groups in crystallographic stacking. This study reveals the influence of chemical mo-dification involving the methyl group(CH₃) onto crystallographic structure of pyridinium ILs. Thermal analysis indicates that the difficult crystallization of the two ILs is related to the low void filling of ion pairs in crystal structure, leading to relatively low melting point and evident supercooling during the cooling process. Additionally, the experimental results indicate that the two ILs have electrochemical activity. The ethyl acetate group also allows downward shifting of electrochemical windows to less negative positions and the ionic conductivities of the two ILs follow an Arrhenius-type behavior.     

二苯并噻吩及其氧化物与离子液体相互作用的理论研究

采用密度泛函理论方法比较了DBT/DBTO₂和[BMIM]⁺[PF₆]^-/[BMIM]⁺[BF₄]^-的相互作用。对最稳定的[BMIM]⁺[PF₆]^-、[BMIM]⁺[PF₆]^--DBT、[BMIM]⁺[PF₆]^--DBTO₂、[BMIM]⁺[BF₄]^-、[BMIM]⁺[BF₄]^--DBT、[BMIM]⁺[BF₄]^--DBTO₂进行了NBO和AIM分析。结果表明,DBT和[BMIM]⁺[PF₆]^-/[BMIM]⁺[BF₄]^-中的咪唑环彼此相互平行,NBO和AIM分析表明它们之间发生了π-π相互作用。H1'和H9'形成的F…H氢键有利于π-π堆积作用的形成。DBTO₂倾向于趋近C2-H2和甲基基团形成O…H相互作用;DBTO₂优先吸附在[BMIM]⁺[PF₆]^-/[BMIM]⁺[BF₄]^-。在模拟油中,[BMIM]⁺[PF₆]^-和[BMIM]⁺[BF₄]^-离子液体对DBTO₂的萃取能力大于DBT,其原因是可能是DBTO₂具有较大的极性和O…H与F…H的氢键作用。     

吡啶离子液体[BPy][BF4]与乙腈混合体系中杜醌的光化学反应动力学

用激光闪光光解方法研究了杜醌(DQ)在吡啶型离子液体N-丁基吡啶四氟硼酸盐([BPy][BF₄])与乙腈(MeCN)组成的共混溶剂中的光化学反应机理与动力学. 实验结果表明, 离子液体[BPy][BF₄]对混合体系中杜醌激发三线态(³DQ^*)的瞬态吸收峰位置和吸光度大小都没有产生明显影响. 在N₂饱和条件下, 无论是在乙腈溶液中还是在[BPy][BF₄]/MeCN混合溶液中³DQ^*的衰减都遵循一级反应动力学规律. 而[BPy][BF₄]的存在对³DQ^*与三乙胺(TEA)之间的电子转移影响显著. 随着[BPy][BF₄]/MeCN 体系中离子液体比例的增加, 杜醌三线态³DQ^*与TEA间的瞬态反应机理没有改变, 但它们之间的光诱导电子转移反应速率和生成自由基的量子产额逐渐降低, 通过改变离子液体的比例可以调节该体系中光诱导电子转移反应的速率和效率.     

Improving Catalytic Performance of Burkholderiacepacia Lipase by Chemical Modification with Functional Ionic Liquids

Various imidazolium and choline-based functional ionic liquids(ILs) comprising different cations and anions were grafted onto Burkholderiacepacia lipase(BCL) through surface amino acids coupling. The catalytic activity, thermostability, organic solvent tolerance and adaptability to temperature and pH changes of the modified BCL were then evaluated in olive oil hydrolysis reaction. The results showed that different combinations of cations and anions in ILs had important influence on the catalytic performance of the modified lipases. BCL modified with IL[Choline] [H₂PO₄] was the most improved lipase, in which increases by 1.2 folds in relative activity, 2.5 folds in typical proton solvent(10% methanol, volume fraction), and 1.4 folds in thermostability(after incubation at 70℃ for 2 h) were achieved in relative toits native form. BCL modified with[HOOCEPEG₃₅₀IM] [BF₄] had higher optimal tempe-rature and pH, and better thermosability compared with the native and other modified BCLs. The conformational changes of BCLs were also confirmed by fluorescence spectroscopy and circular dichroism spectroscopy.