Aromatic polyisophthalamides with oxybenzoyl pendent groups

A series of polyisophthalamides containing pendent oxybenzoyl groups were prepared from 5-oxybenzoyl-isophthaloyl chloride and aromatic diamines. The analogous unsubstituted polyisophthalamides were also prepared in order to compare the two series and to determine the effect of oxybenzoyl pendent groups on the properties of aromatic polyamides. The modified polymers exhibited better solubility than, and approximately the same glass transition temperatures (in the range 260–290°C) as, the parent unsubstituted polymers. The mechanical strength of polymer films was affected only to a small extent by the presence of side groups, but the thermal resistance was negatively affected, with the result that polyisophthalamides with oxybenzoyl pendent groups began to decompose at about 360°C (TGA), 60–100°C lower than the unsubstituted polyisophthalamides. By means of an appropriate thermal treatment, crosslinking of the modified polymers was achieved and their thermal resistance significantly enhanced.     

Synthesis and properties of aromatic polyamides based on a benzonorbornane bis(ether carboxylic acid)

A set of new aromatic polyamides containing ether and benzonorbornane units were synthesized by the direct phosphorylation polycondensation of 3,6‐bis(4‐carboxyphenoxy)benzonorbornane with various aromatic diamines. The polymers were produced in high yields and moderate to high inherent viscosities (0.64–1.70 dL/g). The polyamides derived from rigid diamines such as p‐phenylenediamine and benzidine were semicrystalline and insoluble in organic solvents. The other polyamides were amorphous and organosoluble and afforded flexible and tough films via solution casting. These films exhibited good mechanical properties, with tensile strengths of 95–101 MPa, elongations at break of 13–25%, and initial moduli of 1.97–2.33 GPa. The amorphous polyamides showed glass‐transition temperatures between 176 and 212 °C (by differential scanning calorimetry) and softening temperatures between 194 and 213 °C (by thermomechanical analysis). Most of the polymers did not show significant weight loss before 450 °C in nitrogen or in air. Some properties of these polyamides were also compared with those of homologous counterparts without the pendent norbornane groups. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 947–957, 2002     

Liquid crystalline and photoactive poly[4,4′-stilbeneoxy]alkylbiphenylphosphates

A series of liquid crystalline and photoactive polymers were synthesized from biphenylphosphorodichloridate with various 4,4′-bis(m-hydroxyalkyloxy)stilbenes (m = 2, 4, 6, 8, 10) in chloroform by solution polycondensation method using an acid scavenger. The resultant polymers were characterized by inherent viscosity, FT-IR, ¹H, ¹³C and ³¹P NMR spectroscopies. The liquid crystalline (LC) properties were studied using HOPM and DSC and it was inferred that out of the five polymers synthesized, higher methylene chain containing polymers (m = 6, 8, 10) exhibited LC properties. Thermogravimetric analysis revealed that all the polymers were stable in between 290 and 367 °C and underwent degradation thereafter. The thermal stability and char yield of the polymers decreased with increase in flexible methylene chain. The photochemical properties of these polymers were investigated by UV and fluorescence spectroscopy. Crosslinking proceeds via 2π-2π cycloaddition reaction of the -CHCH- of the stilbene moieties. The rate of crosslinking increases with increase in methylene chain length in the polymer backbone. The fluorescence spectra showed that the longer methylene spacer containing polymers exhibited larger red-shifts than the shorter spacer containing polymers.     

Polyamides based on diamines and N,N′-dimethyldiamines derived from biphenol

Aromatic-aliphatic polyamides containing a biphenyl mesogen were prepared by both interfacial and solution polymerization reactions. Substitution of the amide nitrogen with methyl groups yielded polymers with significantly different properties than the unsubstituted polyamides. The methyl-substituted polyamides had improved thermal stability, significantly lower meltin temperatures, and greater solubility in common solvents. Copolyamides were also synthesized which contained different flexible spacer units that varied in the number of methylene groups. No evidence for the presence of liquid crystalline phases could be obtained in either the unsubstituted polyamides or polyamides containing N-methylated amide units. © 1994 John Wiley & Sons, Inc.     

Novel aromatic polyamides and polyimides functionalized with 4‐tert‐butyltriphenylamine groups

A new triphenylamine‐containing diamine monomer, 4,4′‐diamino‐4″‐tert‐butyltriphenylamine, was successfully synthesized by the cesium fluoride‐mediated N,N‐diarylation of 4‐tert‐butylaniline with 4‐fluoronitrobenzene, followed by the reduction of the nitro group. The obtained diamine monomer was reacted with various aromatic dicarboxylic acids and tetracarboxylic dianhydrides to produce two series of novel triphenylamine‐based polyamides and polyimides with pendent tert‐butyl substituents. Most of the polymers were readily soluble in polar organic solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide (DMAc), and could be solution cast into tough and flexible polymer films. These polymers showed high glass transition temperatures between 282 and 320 °C, and they were fairly stable up to a temperature above 450 °C (for polyamides) or 500 °C (for polyimides). These polymers exhibited UV absorption maxima around 308 to 361 nm. The photoluminescence spectra of the polyamides in DMAc exhibited a peak emission wavelength in the blue at 421–433 nm. Cyclic voltammograms of polyamides and polyimides showed an oxidation wave at 1.0–1.1 V versus Ag/AgCl in an acetonitrile solution. All the polyamides and polyimides exhibited excellent reversibility of electrochromic characteristics by continuous several cyclic scans between 0.0 and 1.1–1.3 V, with a color change from the original pale yellowish neutral form to the green or blue oxidized forms. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4579–4592, 2006     

Poly(1,3,4-oxadiazole-amide)s containing pendent imide groups

A series of new poly(1,3,4-oxadiazole-amide)s containing pendent imide groups has been synthesized by solution polycondensation of aromatic diamines containing preformed 1,3,4-oxadiazole rings with two diacid chlorides containing imide rings. These polymers were also prepared by the reaction of the same diacid chlorides with p-aminobenzhydrazide which were subsequently cyclodehydrated in solid state. The polymers were soluble in polar amidic solvents and some of them gave transparent flexible films by casting from solutions. They showed high thermal stability with decomposition temperatures above 400°C and glass transition temperatures in the range of 245–327°C. They had low dielectric constants, in the range of 3.32–3.94, and good tensile properties.     

The synthesis of mesogenic polymers provoked by molecular mobility. polysiloxanarylenes

An approach to the synthesis of potentially thermotropic liquid crystalline polymers based on parallel investigation of their molecular mobility was realized. The initial idea was provoked by the observation that there exists some correspondence of molecular mobility data and the ability of a polymer to form a liquid crystalline phase. Previously this phenomenon was demonstrated on the example of a series of thermotropic main chain polymers with flexible dimethylsiloxane spacers of variable length. The relation between the structure of the main chain and local molecular mobility of different fragments was investigated in a series of regular polysiloxane-silarylenes containing rigid aromatic sequences. Molecular mobility was studied by dielectric spectroscopy in solution and in solid state. The structure of the main chain has been changed by variation of the repeated fragments' length, substituents and joint groups. The data of molecular mobility and their conformity with the chain structure were used for directed synthetic search of desired mesogenic polymers.     

Synthesis and characterization of soluble,blue-fluorescent polyamides and polyimides containing substituted p-terphenyl as well as long aliphatic segments in the main chain

A novel class of semiflexible polyamides and polyimides bearing substituted p-terphenyl as well as long aliphatic segments in the main chain were synthesized through pyrylium salts. Characterization of polymers was accomplished by inherent viscosity, elemental analysis, FT-IR, NMR, UV-vis luminescence spectroscopy, X-ray analysis, differential scanning calorimetry, thermomechanical analysis, thermogravimetric analysis, isothermal gravimetric analysis, and water uptake measurements. Polyamides displayed a degree of crystallinity and dissolved in polar aprotic solvents containing lithium chloride, as well as in trichloroacetic acid. Polyimides were amorphous and showed an excellent solubility, being soluble in various common solvents. The solutions of polyamides in DMF were blue-fluorescent with maxima at 362–370 nm. The emission maxima were not influenced appreciably upon the structure of the pendent groups and the length of the aliphatic spacers of backbone. The polymers possessed T_gs at 98–131°C and exhibited a satisfactory thermal stability. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3646–3656, 1999     

含聚乙二醇柔性间隔段的主链型液晶聚酯的合成

分子结构与液晶行为间的关系是液晶性高分子物理问题研究的核心,通常的液晶性高分子中除液晶性基元外还引入一些相对来说很柔顺的链段,称作柔性间隔段．这是因为人们认识到高分子的液晶行为不只决定于液晶性基元的结构,也受到这些基元间以及基元和间隔段间相互作用的影...     

Processable heat resistant polyamides containing tetraphenyl thiophene having pendant phenyl moiety with heterocyclic quinoxaline unit: Synthesis and characterization

A series of new polyamides containing tetraphenyl thiophene having pendant phenyl moiety with heterocyclic quinoxaline unit were synthesized by using the solution polycondensation method of novel diamine monomer V with isopthaloyl chloride (IPC) and terpthaloyl chloride (TPC) in various mole proportions. These novel polymers were characterized by FT-IR, solubility, inherent viscosity, thermal analysis and X-ray diffraction studies. Inherent viscosities of these polymers were in the range 0.66 to 1.44 dL/g indicating moderate to high molecular weight built-up. These polymers exhibited solubility in various solvents such as DMAc, NMP, pyridine, m-cresol etc. X-ray diffraction pattern of polymers showed that introduction of pendant phenyl moiety would disturb the chain regularity and packing, leading to amorphous nature. Thermal analysis by TGA and DSC showed excellent thermal stability of polymers. The structure -property correlation among these polyamides were studied, in view of these polymer's potential applications as processable high temperature resistance materials.     

Synthesis,characterization and properties of novel polyamides containing ferrocene unit and flexible spacers

Synthesis and characterization of ferrocene‐containing main‐chain polyamides are reported in this article. A new, interesting type of organometallic monomer (FDADO) based on ferrocene was prepared by interfacial condensation of 1,1′‐dichlorocarbonyl ferrocene with 2 mol 1,8‐diamino‐3,6‐dioxaoctane (DADO). A series of ferrocene‐based polyamides was prepared via polycondensation of the ferrocenyl diamine (FDADO) with different diacid chlorides using two different methods. The monomer and polymers were characterized by elemental analysis, infrared and NMR spectroscopy. The thermal stability and behavior of the synthesized polymers were evaluated by thermal gravimetric analysis (TGA), dynamic mechanical thermal analysis (DMTA), and differential scanning calorimetry (DSC). The crystallinity of polymers was examined by X‐ray diffraction analysis. Inherent viscosity, solubility and flame‐retardancy of the polymers were also studied. The obtained polymers showed good heat‐resistance and flame‐retardancy, and improved solubility vs generally reported polyamides in some common organic solvents. Copyright © 2007 John Wiley & Sons, Ltd.     

Synthesis and properties of Ortho-linked aromatic polyamides based on 4,4′-(2,3-naphthalenedioxy) dibenzoic acid

A novel aromatic dicarboxylic acid monomer, 4,4′-(2,3-naphthalenedioxy)-dibenzoic acid ( 3 ), was prepared by the fluorodisplacement reaction of p-fluorobenzonitrile with 2,3-dihydroxynaphthalene in N,N-dimethylformamide (DMF) in the presence of potassium carbonate followed by alkaline hydrolysis of the intermediate dinitrile. A series of novel aromatic polyamides containing ortho-linked aromatic units in the main chain were synthesized by the direct polycondensation of diacid 3 and a variety of aromatic diamines using triphenyl phosphite and pyridine as condensing agents in the N-methyl-2-pyrrolidone (NMP) solution containing dissolved calcium chloride. The resulting polyamides had inherent viscosities higher than 0.74 and up to 2.10 dL/g. All of these polyamides were soluble in polar solvents, such as NMP, DMF, N,N-dimethylacetamide (DMAc), and dimethyl sulfoxide. Transparent, flexible, and tough films could be cast from their DMAc or NMP solutions. The solvent-cast films had high tensile strengths and moduli. Extensions to break were relatively low, except for the polymers derived from 2,2-bis[4-(4-aminophenoxy)phenyl]hexafluoropropane and 3,4′-oxydianiline, which had elongations of 82 and 62%, respectively. Except for the polyamide based on p-phenylenediamine, all the other polyamides were amorphous in nature. All the polymers are thermally stable to temperatures in excess of 450°C in either air or nitrogen atmosphere. The polymers exhibited glass transition temperatures ranging from 183 to 260°C and decomposition temperatures (10% weight loss) ranging from 462–523°C in air and 468–530°C in nitrogen. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3385–3391, 1997     

Synthesis,characterization, and water sorption properties of new aromatic polyamides containing benzimidazole and ethylene oxide moieties

New polyamides, containing a benzimidazole side group and ethylene oxide moieties in the structural repeat unit, were synthesized by low‐temperature polycondensation. The aim of this design was to obtain polyamides that were more soluble in common organic solvents and hence had better processability than benzimidazole polyamides while maintaining the water sorption properties characteristic of the latter. The results showed that the number of ether linkages of the repeat unit played an important role in the glass‐transition temperature and in the water sorption properties, the polyamides with one or two ethylene oxide units being more hydrophilic than benzimidazole polyamides. However, the length of the ethylene oxide chain played a minor role in the solubility because the second member of the series, with two ether linkages (i.e., one ethylene oxide unit), reached the same level of solubility as those polyamides with more ethylene oxide moieties. No crystallinity was observed by X‐ray and calorimetric measurements for the new polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 112–121, 2005     

Synthesis and characterization of aromatic polyamides containing alkylphthalimido pendent groups

A series of polyisophthalamides containing pendent phthalimido groups and flexible side spacers were prepared from four novel diacids and three commercial aromatic diamines. These polyamides were prepared in high yields and with high molecular weights by direct polycondensation with triphenyl phosphite and pyridine as condensing agents. The weight‐average and number‐average molecular weights, measured by gel permeation chromatography, were 70,000–137,000 and 47,000–86,000 g/mol, respectively. The novel polyamides were amorphous and readily soluble and showed glass‐transition temperatures of 150–240 °C, as measured by differential scanning calorimetry. Thermogravimetric analysis showed that the 10% weight‐loss temperatures in nitrogen were 355–430 °C, a significant improvement in thermal stability having been observed with the increase in the side‐chain length. A theoretical quantum mechanical study was successfully carried out to explain these results. Flexible and tough films, cast from polymer solutions, showed tensile strengths of 50–125 MPa. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3711–3724, 2002     

On the liquid-crystalline properties of methacrylic polymers containing 4′-(4-alkyloxyphenyl)azobenzene mesogens

In this article, we report on the synthesis and thermotropic behaviour of methacrylic polymers containing 4′-(4-alkyloxyphenyl)azobenzene mesogens attached to the backbone through n-alkyloxy spacers of 6 or 10 methylene groups. Polymerisations were carried out via free radicals using azobisisobutyronitrile (AIBN) as initiator. Chemical structures of polymers and their precursors were characterised by ¹H NMR spectroscopy. Thermogravimetric analysis showed that azopolymers are thermally stable up to temperatures around 300°C. The thermotropic liquid-crystalline (LC) behaviour was studied by differential scanning calorimetry (DSC), polarized optical microscopy (POM) and X-ray diffraction (XRD). Results indicate that all synthesised mesogens, monomers and polymers developed two or more orthogonal LC phases in wide temperature ranges. Mesogens and monomers developed nematic and smectic phases, whereas polymers exhibited only smectic phase. In polymers, the arrangement of mesogens depends on the relative length of the spacer and the terminal flexible chain; two distinct structural models were proposed based on chemical interactions and steric constrains. The trans–cis photoisomerisation of monomers and polymers in solution was also studied. High cis-isomer contents (>80%) were reached in relative short irradiation times despite the steric constrains imposed by the polymer backbone.     

Synthesis and properties of new aromatic polyamides with redox‐active 2,4‐dimethoxytriphenylamine moieties

A new triphenylamine‐based diamine monomer, 4,4′‐diamino‐2″,4″‐dimethoxytriphenylamine ( 2 ), was synthesized from readily available reagents and was reacted with various aromatic dicarboxylic acids to produce a series of aromatic polyamides ( 4a–h ) containing the redox‐active 2,4‐dimethoxy‐substituted triphenylamine (dimethoxyTPA) unit. All the resulting polyamides were readily soluble in polar organic solvents and could be solution cast into tough and flexible films. These polymers exhibited good thermal stability with glass transition temperatures of 243–289 °C and softening temperatures of 238–280 °C, 10% weight loss temperatures in excess of 470 °C in nitrogen, and char yields higher than 60% at 800 °C in nitrogen. The redox behaviors of the polymers were examined using cyclic voltammetry (CV). All these polyamides showed two reversible oxidation processes in the first CV scan. The polymers also displayed low ionization potentials as a result of their dimethoxyTPA moieties. In addition, the polymers displayed excellent stability of electrochromic characteristics with coloration change from a colorless neutral state to green and blue‐purple oxidized states. These anodically coloring polyamides showed high green coloration efficiency (CE = 329 cm²/C), high contrast of optical transmittance change (ΔT% = 84% at 829 nm), and long‐term redox reversibility. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3392–3401, 2010     

Use of ionic liquid and microwave irradiation as a convenient, rapid and eco-friendly method for synthesis of novel optically active and thermally stable aromatic polyamides containing N-phthaloyl-l-alanine pendent group

An efficient, fast and easy method for synthesis of new optically active and thermally stable aromatic polyamides (PAs) containing pendent phthalimide group and l-alanine flexible side spacer using room temperature ionic liquid (RTIL) by microwave irradiation has been investigated. The results found that RTIL efficiently absorb microwave energy, thus leading to a very high heating rate. All the PAs showed excellent solubility and readily dissolved in various organic solvents. Thermogravimetric analysis (TGA) exhibited that polymers were stable, with 10% weight loss recorded above 373 and 418 °C in the nitrogen atmosphere. In order to see the efficiency of microwave irradiation, this method was compared with polycondensation of the same monomers in RTILs using conventional heating.     

Soluble aromatic poly(ether amide)s containing aryl‐, alkyl‐, and chloro‐substituted phthalazinone segments

A series of novel aromatic diamines ( 2 – 4 ) containing the alkyl‐, aryl, or chloro‐substituted group of phthalazinone segments were synthesized via two synthetic steps starting from 4‐(3‐R‐4‐hydroxyphenyl)‐2,3‐phthalazinone‐1 (R = Ph, CH₃, Cl). Three series of aromatic polyamides containing phthalazinone moieties were prepared through diamines 2 – 4 reacting with different aromatic dicarboxylic acids via a direct Yamazaki–Higashi phosphorylation polycondensation reaction. The resulting aromatic polyamides had inherent viscosities in the range of 0.40–0.76 dL/g. The thermal property of the polyamides was examined with DSC and thermogravimetric analysis. The glass‐transition temperatures of these polyamides ranged from 298 to 340 °C. The 10% mass‐loss temperature was above 405 °C under nitrogen. Structures of monomers 2 – 4 and the polymers were confirmed by Fourier transform infrared spectroscopy, ¹H NMR, and mass spectrometry. Good solubility of these polymers in polar solvents such as N‐methylpyrrolidone, dimethylformamide, dimethylacetamide (DMAc), and m‐cresol was observed, and tough, flexible films were obtained from the polymer's DMAc solutions. The effect of the substituted group on the physical property of polymers was also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2026–2030, 2004     

胆甾侧链聚硅氧烷高分子液晶的合成与相行为研究

本工作利用双键与Si-H键的加成反应合成了以丙烯酸胆甾醇酯为侧链的硅氧烷梳状聚合物液晶ECS.聚合物的结构得到了核磁与红外分析的证明.偏光显微镜和DSC对ECS的相态转变研究表明,ECS在一定的温度范围内能够形成液晶相,液晶相的存在范围与聚合物的结构密切相关.     

新型芳香性螺双内酯聚合物的合成

以间二甲苯和多聚甲醛为原料合成了芳香性螺双内酯单体———５ ,５′ 二甲酰氯 ７ ,７′ 二氧 ２ ,２′ 螺双（ 苯并四氢呋喃） ,并通过常温溶液缩聚和界面缩聚合成了一系列聚酰胺和聚酯．研究了聚合物的核磁、红外光谱及其溶解性、热性能和聚酰胺薄膜的力学性能．含芳香性螺双内酯的聚酰胺在极性溶剂中具有良好的溶解性、高的热稳定性和一定的力学性能．