新型铜配合物修饰热解石墨电极上的氧电催化还原

 采用新型单核铜配合物高氯酸咪唑N-2-羟基乙基二乙烯三胺合铜(Ⅱ)(Cu［L(ImH)］(ClO4)2)修饰热解石墨(PG)电极表面制得了Cu［L(ImH)］/PG电极,并采用循环伏安法和电位阶跃实验研究了该电极对氧的催化还原作用. 结果表明,该电极在中性和碱性条件下对氧气的催化还原具有良好的稳定性,还原峰电流随电位扫描速度的增大而增强,Ip～v1/2呈线性关系. 根据电位阶跃实验的I～t-1/2曲线,计算出电极反应的电子转移数约为4, 推断氧气在该电极上的还原是经历了4电子过程还原为水,催化机理属于混合控制的ECE (E电极反应, C化学反应)过程.     

CoSALEN/APO-5复合材料的制备及其电催化还原氧的性能

将金属钴离子引入磷酸铝分子筛APO-5制得CoAPO-5分子筛,再把N,N-双水杨醛缩乙二胺(SALEN)希夫碱通过扩散进入CoAPO-5分子筛孔道并与其中的钴离子配位,形成了CoSALEN配合物,构成CoSALEN/APO-5复合材料.应用物理吸附法,以聚苯乙烯(PS)作粘结剂,将CoSALEN/APO-5涂敷在玻碳电极表面制成修饰电极PS/CoSALEN/APO-5/GCE.循环伏安法(CV)、计时电流法(CA)研究了该修饰电极在不同pH电解质溶液中的电化学行为以及对分子氧的催化还原作用.结果表明,制备的修饰电极能有效地催化分子氧的四电子还原,即氧气被电催化还原为水,据此提出可能的氧还原机理.     

聚血红素修饰电极上氧还原的电催化研究

 采用循环伏安法和电位阶跃法,研究了水溶液中溶解氧在聚血红素修饰电极上还原反应的电催化作用．结果表明,还原峰电流随扫描速度的增大而增强,Ip～v1／2呈线性关系．根据电位阶跃实验的I～t曲线,计算出电极反应的电子转移数约为2,推断其催化机理属于ECE催化过程．     

超氧化物歧化酶在纳米金/L-半胱氨酸修饰金电极上的电化学行为

通过L-半胱氨酸将纳米金修饰到金电极上,把超氧化物歧化酶(SOD)固定在修饰电极表面,制备了SOD-纳米金/L-半胱氨酸修饰电极。运用交流阻抗法、循环伏安法等方法表征了该电极,发现SOD在该电极上于0.15V和-0.05V左右产生较明显的氧化还原峰,在0.04～0.24V/s扫描速率范围内,其还原峰电流与扫描速速呈线性关系,表明该电极过程受吸附控制。研究了H2O2对SOD-纳米金/L-半胱氨酸修饰电极伏安行为的影响,发现该电极的还原峰电流与H2O2浓度在1.0×10-6～2.0×10-4mol/L范围内呈良好的线性关系,相关系数为-0.996,可用于对H2O2的分析检测。     

蒽醌/聚吡咯复合膜修饰电极的电化学行为和电催化活性

在水溶液中制备了掺杂蒽醌磺酸盐(AQS)的聚吡咯(PPy)/玻碳复合膜修饰电极,采用循环伏安法和旋转圆盘电极技术研究了该修饰电极在不同pH值溶液中的电化学行为以及在pH=5.5的磷酸盐缓冲溶液中对氧还原反应的电催化性能和动力学.结果表明,与裸玻碳电极相比,PPy膜的存在不仅降低了AQS的反应电位和峰电位差,而且增大了其氧化还原反应的峰电流,H2AQ/HAQ-氧化还原对的电离常数为9.5.AQS/PPy膜修饰电极上氧的还原主要是两电子还原为H2O2的不可逆过程,H2AQ对氧还原反应起主要催化作用,还原过程符合异相氧化还原催化机理.该修饰电极具有良好的电化学重现性.     

对乙酰氨基酚在石墨烯和离子液体复合修饰电极上的电化学行为及其测定

制备了石墨烯和疏水性离子液体1-丁基-3-甲基咪唑六氟磷酸盐(BMIMPF6)复合修饰电极(Gene-BMIMPF6/GCE),运用循环伏安法研究了对乙酰氨基酚(PT)在该复合修饰电极上的电化学行为。结果表明,在pH=6.5的磷酸盐缓冲溶液中,PT在复合修饰电极上出现一对明显的氧化还原峰,在20～260mV/s的扫描速率范围内,其氧化还原峰电流均与扫描速率平方根(v1/2)呈线性关系,表明该电极过程是受扩散控制的。优化了方波溶出伏安法(SWSV)的实验参数,PT浓度在6.0×10-7～8.0×10-5mol/L范围内与峰电流Ipa呈线性关系,检出限(S/N=3)为1.0×10-7 mol/L。采用该法对PT进行加入回收测定,回收率为96.9%～101.2%。     

多巴胺在电沉积石墨烯修饰碳分子线电极上的电化学测定

以分子线二苯乙炔为修饰剂和粘合剂制备了一种新型的碳糊电极-碳分子线电极(CMWE),并以其为基底电极采用电化学还原法将石墨烯(GR)沉积到CMWE表面得到电沉积石墨烯修饰碳分子线电极(GR/CMWE)。考察了多巴胺(DA)在该修饰电极上的电化学行为。实验结果显示DA在GR/CMWE上出现了1对峰形良好的氧化还原峰,与裸电极相比,该氧化还原峰的电流增大,峰电位差减小,表明修饰电极对DA的电化学反应有催化作用。在最佳实验条件下峰电流与DA浓度在8.0×10-7~2.0×10-3mol/L范围内呈良好的线性关系,检出限(3σ)为2.55×10-7mol/L。将该电极用于多巴胺注射液样品的检测,结果满意。     

壳聚糖-g-N-羧甲基-二（2-苯并咪唑）-1,2-乙二醇和纳米金溶胶复合物固定漆酶修饰玻碳电极的直接电化学

制备了壳聚糖-g-N-羧甲基-二（2-苯并咪唑）-1,2-乙二醇（CTS-g-N-CBBIE）,将其与纯化的纳米金溶胶（NGS）共混得到CTS-g-N-CBBIE-NGS复合物。 以此复合物作为固酶载体固定云芝漆酶,固酶量大（31.10 mg/g）,固酶比活力高（1.43 U/mg）;此固酶复合物修饰的玻碳电极在无氧磷酸盐-柠檬酸盐缓冲溶液（pH=5.0）中可以实现无中介酶-电极直接电子迁移（一对准可逆氧化还原峰式电位576 mV(vs.Ag/AgCl)对应于漆酶活性中心T1位的氧化还原）,电子迁移速率常数为228.3 s-1。 当氧气浓度较小时,这种固酶修饰电极对氧气还原具有一定的生物电催化性能（空气饱和缓冲溶液中氧还原峰电位约为320 mV(vs.Ag/AgCl)）。 当氧气浓度增高后,氧还原反应受到抑制;但这种漆酶修饰电极对pH较为敏感,且稳定性和重复使用性欠佳。     

纳米二氧化铈修饰碳糊电极线性扫描伏安法测定苯酚

在0.01mol.L-1硼砂溶液(pH 9.18)中,用纳米二氧化铈修饰碳糊电极作为工作电极,线性扫描伏安法测定苯酚。伏安图上出现一灵敏的氧化峰,其峰电位为+0.56V(vs.SCE),峰电流与苯酚的浓度在1.0×10-7～2.0×10-4 mol.L-1范围内呈线性关系,检出限(3s/k)为5.0×10-8 mol.L-1。富集时间为30s,同时采用线性扫描伏安法研究苯酚在纳米二氧化铈修饰碳糊电极上的氧化还原反应,结果表明此电极反应为一不可逆的吸附过程。     

聚氨基黑10B/Nafion修饰电极上多巴胺的检测

用电化学聚合法制备了聚氨基黑10B/Nafion修饰电极,利用循环伏安法研究了多巴胺在此修饰电极上的电化学行为.在磷酸盐缓冲溶液(pH 6.0)中,多巴胺在修饰电极上呈现可逆的氧化还原峰.其峰电位都随pH值的增加而负移.多巴胺氧化还原峰电流与其浓度在0.2～30 μmol/L范围内呈良好的线性关系;检出限为1.0×10~7 mol/L.实验结果表明:本修饰电极具有良好的重现性、稳定性和较强的抗干扰能力.将此修饰电极用于多巴胺注射液和小牛血清中多巴胺的检测,结果令人满意.     

Electroreduction of dioxygen on Aunano-DNA film electrode in acidic electrolyte

The colloidal Au nanoparticles-deoxyribonucleic acid (Au(nano)-DNA) film modified glassy carbon electrode (GCE) has been fabricated and the electrochemical reduction of dioxygen (O(2)) at this modified GCE has been studied in 0.2 mol/L air-saturated acetate buffer (pH=5.2) using cyclic voltammetry (CV), chronocoulometry (CC), linear scan voltammetry (LSV) and rotating disk electrode (RDE) as diagnostic techniques. The modified electrode shows excellent enhancement effect towards the reduction of dioxygen to hydrogen peroxide (H(2)O(2)), and the overpotential is lower than that at bare GCE. A well-defined dioxygen reduction peak appeared at about -0.24 V. Based on experimental results, a reaction mechanism is proposed and discussed.     

Catalysis of dioxygen reduction at soluble polyaniline modified electrode

A reflux-treatment of soluble polyaniline (SPA) in dimethylformamide (DMF) containing CoCl₂ yields an active catalyst for dioxygen reduction which can be adsorbed on the electrode surface firmly. The catalytic reduction of dioxygen at the glassy carbon (GC) electrode modified by the catalyst was studied with cyclic voltammetry (CV), rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE). The kinetic process of dioxygen reduction at the modified electrode was analyzed with a new RRDE theory dealing with a nondiffusion-controlled process on ring electrode. The rate constants for each scheme of dioxygen reduction were calculated, showing that only 2-electron reduction to H₂O₂ was conducted at the modified electrode. The effect of solution acidity on the electrocatalytic behaviour for dioxygen reduction was investigated. A possibility of initiating catalytic activity for dioxygen reduction was explored with ESCA method.     

化学修饰电极的研究 ⅩⅤⅡ四苯基铁卟啉化学修饰玻碳电极的热处理及其对氧的催化还原

关于金属卟啉、酞菁等化学修饰电极的研究已有大量工作发表.这类电极很不稳定,例如著名的面-面双钴卟啉修饰电报,虽然能直接催化氧还原为水,但经受不住几次电位扫描就失去催化活性.因此,如何提高稳定性就成为研究这类电极的关键.近年来有人报道,吸附在活性碳上的金属卟啉、酞菁类化合物经热处理,可改善其稳定性。热处理后得到的粉状碳催化剂,由于完全不溶于水及有机溶剂,制备电极非常困难。曾有过用这种     

Oxygen reduction at the surface of glassy carbon electrodes modified with anthraquinone derivatives and dyes

The preparation, electrochemical and catalytic behaviour of glassy carbon electrodes modified by anthra-9,10-quinone, its amino derivatives and dyes were investigated. The stability of the modified electrodes was studied by cyclic voltammetry in acidic and neutral media. The electrocatalytic ability of the modified electrodes for the reduction of dioxygen to hydrogen peroxide was examined by cyclic voltammetry, chronoamperometry and chronocoulometry techniques. The influence of pH on the electrochemical and catalytic behaviour was studied and pH 5.0–8.0 was chosen as the optimum working pH by comparing the shift in oxygen reduction potential. The anthraquinone-adsorbed glassy carbon electrodes possess excellent electrocatalytic abilities for dioxygen reduction with overpotential ranging from 280 to 560 mV lower than that at a plain glassy carbon electrode. Hydrodynamic voltammetric studies were performed to determine the heterogeneous rate constants for the reduction of O₂ at the surface of the modified electrodes, mass specific activity of the anthraquinones used and the apparent diffusion coefficient of O₂ in buffered aqueous O₂-saturated solutions. Studies showed the involvement of two electrons in dioxygen reduction.     

Electrochemical reduction of dioxygen on Alizarin modified glassy carbon electrode in acidic medium

The catalytic behaviour of glassy carbon electrode modified by 1,2-dihydroxy antraquinone (Alizarin) was investigated. The electrocatalytic ability of modified electrode for the reduction of dioxygen was examined by cyclic voltammetry and rotating disk electrode (RDE) voltammetry techniques. The Alizarin modified glassy carbon electrode possesses excellent electrocatalytic abilities for dioxygen reduction over potential 400 mV lower than at the bare glassy carbon electrode. Hydrodynamic studies were performed to determine the heterogeneous rate constant for the reduction of O₂ at the surface of modified electrode. It was determined by Koutecky-Levich plot. The apparent diffusion coefficient of O₂ in O₂ saturated acidic solutions was estimated by using Levich equation. Studies show the involvement of four electrons in dioxygen reduction at the surface of this modified electrode.     

Electrocatalytic Reduction of Dioxygen at Carbon Paste Electrode Modified with a Novel Cobalt(III) Schiff's Base Complex

A carbon paste modified electrode with a new cobalt(III) Schiff's base complex (CPME) and its application to electrocatalytic activity for dioxygen reduction is developed. The electrochemical behavior and stability of the CPME as well as the two‐electron reduction of O₂ at the electrode were investigated using cyclic voltammetry, chronoamperometry and rotating disk electrode methods. At the CPME, the reduction of dioxygen to hydrogen peroxide occurs at potentials where it is not observed at a bare carbon paste electrode. The CPME exhibited potent and persistent electrocatalysis for O₂ reduction in acetate buffer solutions of pH 4.0 with an overpotential of about 800 mV lower than unmodified CPE and drastic increase in the peak current. The heterogeneous rate constant for the reduction of O₂ at the surface of CPME was determined by hydrodynamic voltammetry using the Koutecky–Levich plot. A possible catalytic mechanism is proposed and discussed.     

Effects of surfactants on the electroreduction of dioxygen at an acetylene black electrode.

An acetylene black electrode modified by an adsorbed cationic surfactant, cetyltrimethylammonium bromide (CTAB), was developed. The influences of various types of surfactants on the electroreduction of O2 were investigated. It was demonstrated that a cationic surfactant, CTAB, on the surface of the electrode could significantly decrease the overpotential of dioxygen reduction, and the reduction peak current of O2 was also remarkably increased. The reduction of O2 at a CTAB modified acetylene black electrode was studied using cyclic voltammetry, chronocoulometry and controlled potential coulometry. The total number of electrons, the exchange current density (j(o)) and the transfer coefficient (alpha) for reduction of O2 at the surface of this modified electrode were determined.     

Electrocatalytic reduction of dioxygen on a glassy carbon electrode modified with adsorbed cobaloxime complex.

The preparation and electrochemical properties of a glassy carbon (GC) electrode modified with cobaloxime complex were investigated. The complex of the type [CoIII(DO)(DOH)pn)Cl2] where (DO)(DOH)pn = N2,N2'-propanediylbis-2,3-butanedione-2-imine-3-oxime) was adsorbed irreversibly and strongly on the surface of preanodized glassy carbon electrode. Electrochemical behavior and stability of modified GC electrode were investigated by cyclic voltammetry. The electrocatalytic reduction of dioxygen has been studied using this modified glassy carbon electrode by cyclic voltammetry, chronoamperometry and rotating disk electrode voltammetry as diagnostic techniques. The modified electrode showed excellent eletrocatalytic ability for the reduction of dioxygen to hydrogen peroxide in acetate buffer (pH 4.0) with overpotential 1.0 V lower than the plain glassy carbon electrode. The formal potential for this modified electrode is not shifted to more negative potentials by repeated reduction-oxidation cycles in oxygen-saturated supporting electrolyte solution. The apparent electron transfer rate constant (kS), the transfer coefficent (alpha) and the catalytic rate constant of O2 reduction at a GC modified electrode were determined by cyclic voltammetry and rotating disk electrode voltammetry and were found to be around 2.6 s(-1), 0.33 and 2.25 x 10(4) M(-1) s(-1). Based on the results, a catalytic mechanism is proposed and discussed.     

钴卟啉修饰电极对分子氧电催化还原的扫描隧道显微镜研究

利用扫描隧道显微镜(STM)研究了高定向热解石墨(HOPG)和玻璃碳电极(GC)表面的性质, 并对修饰钴卟啉后的表面形貌变化进行了探讨。结合修饰钴卟啉前后的循环伏安结果和STM形貌图, 讨论了电极表面的结构对分子氧的电催化还原反应的影响。从微观角度阐述了GC电极对氧的电催化还原活性明显高于HPOG电极的内在因素,为修饰电极的表面性能研究提供了经验。