全氟甲基乙烯基醚和其它含氟单体乳液共聚合的竞聚率测定

分别通过气相色谱法测定了全氟甲基乙烯基醚 (PMVE)与偏氟乙烯 (VDF)以及PMVE与四氟乙烯(TFE)二元乳液共聚反应中的气相单体组成和共聚物组成 ,然后用非线性回归法 (RREVM )计算得TFE PMVE及VDF PMVE乳液共聚合反应的表观竞聚率分别为γTFE =3 89和γPMVE =0 0 5以及γVDF =1 0 6和γPMVE =0 11.结合已经测定的TFE VDF二元乳液共聚的表观竞聚率 ,计算了由VDF TFE PMVE三元乳液共聚合反应合成的共聚物组成 ,后者与由1 9F NMR实测的共聚物组成吻合     

VDF/TFE/PMVE三元共聚物的结构与性能研究

控制不同单体的起始组成合成了一系列偏氟乙烯 (VDF) 四氟乙烯 (TFE) 全氟甲基乙烯基醚 (PMVE)三元共聚物 ,通过1 9F NMR测定了这类三元共聚物的组成 ,结果与按竞聚率的计算结果吻合 .进一步分别用DSC和WAXD表征了玻璃化温度和结晶度 ,实验结果发现用这类三元共聚物制成的硫化胶的性能与其组成和微观结构密切相关     

4-乙烯基吡啶与丙烯酰胺共聚合的研究

以过硫酸钾为引发剂 ,采用溶液自由基共聚合方法 ,实现了丙烯酰胺 (AM)与 4 乙烯基吡啶 (4 VP)的共聚合 .通过详细研究共溶剂体系、单体总浓度、反应温度、反应时间及引发剂量对共聚合过程中转化率和分子量的影响 ,从而确定了适宜的共溶剂体系和最佳的工艺条件 .用紫外分光光度法测得了共聚物的组成 .用Kelen Tudos方法 ,求得 4 乙烯基吡啶 (4 VP)和丙烯酰胺 (AM)单体的竞聚率 ,r4 VP =0 6 4 4 ,rAM =0 371.最后通过FTIR和1 3C NMR表征共聚物的结构并验证了共聚物的组成 .     

单茂钛/MAO体系催化乙烯/丙烯共聚合研究Ⅱ.乙烯/丙烯共聚物的核磁共振分析

用13C NMR测定了由单茂基钛化合物 /mMAO催化体系制备的乙烯 /丙烯共聚物大分子链的立体结构和单体序列分布 ,计算了单体的竞聚率r1=7 91± 0 0 6 ,r2 =0 135± 0 0 3 ,其乘积r1r2 ≈ 1.Fineman Ross计算得到的单体竞聚率与13C NMR测定值相近 ,即r1=7.94,r2 =0 .134,其乘积r1r2 =1 0 4.这表明共聚物是立构无规的 .共聚物经溶剂萃取后 ,乙醚可溶和己烷可溶两个级分中单体的序列分布和竞聚率略有不同 .乙醚可溶级分中丙烯链段稍长 ,而己烷可溶级分中乙烯链段稍长     

对甲氧基苯辛基二甲基烯丙基氯化铵与丙烯酰胺共聚动力学研究

采用定时取样研究了以过硫酸钾-亚硫酸氢钠为引发剂,对甲氧基苯辛基二甲基烯丙基氯化铵(ADMAAC)和丙烯酰胺(AM)在水溶液中的共聚反应动力学,测定了相应的聚合速率方程、聚合表观活化能;采用阴阳离子相互作用测定残余ADMAAC的含量,紫外分光光度法测定残余AM的含量,根据单体投料量和残余量差值,得到低转化率下共聚物的组成,按Kelem-Tudos法得到两单体竞聚率。实验结果表明:聚合反应温度在40℃下,聚合速率方程为:Rp=K[M]1.241[KPS]0.52[SHS]0.55;根据Arrhenius经验公式计算出对甲氧基苯辛基二甲基烯丙基氯化铵(ADMAAC)和丙烯酰胺(AM)共聚的表观活化能为73.85kJ/mol,高于AM水溶液均聚合的活化能Ea(70.32kJ/mol);两种单体的竞聚率为rADMAAC=0.197、rAM=4.503,为ADMAAC-AM共聚合反应控制确定了重要的动力学参数。两单体的竞聚率的积小于1,ADMAAC与AM共聚合行为类型是一种无恒比点的非理想共聚行为,共聚物组成曲线,在对角线下方。     

(2-甲基丙烯酰氧乙基)三甲基氯化铵-丙烯酰胺双水相共聚合

将(2-甲基丙烯酰氧乙基)三甲基氯化铵(DMMC)与丙烯酰胺(AM)在聚乙二醇(PEG)水溶液中进行双水相共聚合(ATPC),并与DMMC/AM均相水溶液共聚合(HASC)进行比较.在均相水溶液共聚合体系中得到了DMMC/AM共聚体系的竞聚率分别为rDMMC=1.77、rAM=0.32,并给出了竞聚率的95%,99%联合置信区域.比较了两种共聚合体系的转化率-时间曲线和共聚组成,表明双水相共聚合体系初期反应速率高于均相水溶液共聚合体系,但最终转化率相似;两种共聚合体系得到的共聚物组成有较大差别.测得了DMMC、AM以及DMMC-AM共聚物(CPAM)在65℃、反应条件下的相分配系数为K1=0.035、K2=0.125和Kp=0.011.结合双水相聚合的本质以及单体和共聚物在两相的分配系数,提出了一个计算双水相共聚组成的新方法,用该方法计算的双水相共聚合体系的共聚组成与实验点吻合较好.     

茂钛对乙烯基单体催化聚合(Ⅳ)——二氯二茂钛催化丙烯腈与甲基丙烯酸甲酯共聚合反应的研究

本文研究了光照对二氯二茂钛催化丙烯腈与甲基丙烯酸甲酯共聚合反应的影响.以NMR谱法测定了共聚物中两种单体的组成比.用四种方法计算了竞聚率r₁和r₂.证明了在光照下二氯二茂钛对单体催化聚合过程为一种自由基机理.     

气相色谱法测定共聚合竞聚率的研究

以苯乙烯和甲基丙烯酸正丁酯共体系为例，在共聚单体敏感点组成附近做重复实验，进行了４０、６０、８０、１００、１２０℃下的低转化率的共聚合，用气相色谱测定共聚物的组成，用Ｍａｙｏ－Ｌｅｗｉｓ微分组成方程的误差变量法计算竞聚率，同时给出竞聚率的９５％可信椭圆区间。通过与ＦＴＩＲ、ＮＭＲ方法的比较，对气相色谱法测定竞聚率的准确性进行了讨论。     

甲基丙烯酸缩水甘油酯与甲基丙烯酸甲酯的共聚合及竞聚率测定

以N,N-二甲基甲酰胺(DMF)为溶剂,实施了甲基丙烯酸缩水甘油酯(GMA)与甲基丙烯酸甲酯(MMA)的溶液共聚合,测定了共聚物P(GMA-co-MMA)的红外光谱(FT-IR),对其化学结构进行了表征,并采用差示扫描量热法(DSC)测定了共聚物的玻璃化转变温度(Tg).改变两单体投料比进行共聚合,采用化学分析法测定低转化率下(<7%)共聚物组成,重点研究了两单体的竞聚率.结果表明:GMA与MMA的共聚合易于进行,P(GMA-co-MMA)的玻璃化转变温度(Tg)介于均聚物PGMA(72℃)与PMMA(106℃)之间,当n(GMA)/n(MMA)=4/6时,共聚物的Tg为9l℃.采用FR和KT 2种作图法及YBR计算法对单体的竞聚率进行了计算和比较,结果表明:KT和YBR法较为准确,以DMF为溶剂时,GMA与MMA的竞聚率分别为2.14与0.69.     

取代基对系列有机锡单体与MMA共聚活性的影响

本文采用红外光谱技术测定了共聚物的组成,用最小二乘曲线拟合法计算了甲基丙烯酸三甲基锡酯(TMTM),三乙基锡酯(TETM),三丁基锡酯(TBTM),和三苯基锡酯(TPTM)与甲基丙烯酸甲酯(MMA)的共聚合竞聚率,其数值分别为:r_1=1.07,r_2=0.63(TMTM/MMA);0.87,0.62(TETM/MMA);0.62,0.58(TBTM/MMA);0.68,0.60(TPTM/MMA),并计算了各单体的δ和e值,讨论了不同取代基结构对其共聚合相对活性的影响。     

丙烯酸酯和甲基丙烯酸酯基团转移共聚研究

研究了三种丙烯酸酯分别和四种甲基丙烯酸酯的基团转移共聚，用１Ｈ ＮＭＲ法测定共聚物组成，扩展的Ｋｅｌｅｎ Ｔｕｄｏｓ法测定竞聚率，结果为γＭＡ＝９２３、γＭＭＡ＝００６；γＥＡ＝１４１５、γＭＭＡ＝００１；γＢＡ＝７５１、γＭＭＡ＝００２；γＭＡ＝１４４１、γＥＭＡ＝００１；γＭＡ＝１３９６、γＢＭＡ＝０２３；γＭＡ＝８６６、γｉ ＢＭＡ＝００８，表明基团转移聚合同阴离子聚合有明显的相似之处．     

Characterization and quantification of microstructures of a fluorinated terpolymer by both homonuclear and heteronuclear two‐dimensional NMR spectroscopy

Fluoropolymers are usually insoluble in organic solvents. Insolubility of fluoropolymers limits basic characterization such as microstructural investigations. In the family of fluoropolymers, terpolymer of tetrafluorethylene (TFE), hexafluoropropylene (HFP), and vinylidene fluoride (VDF), named THV is one of the newest members. There are nine grades of THV available. Among the nine grades, THV‐221 G is an ideal model polymer for basic characterization purposes. THV‐221 G is soluble in solvents such as acetone and ethyl acetate. In the current report, both homonuclear and heteronuclear 2D NMR experiments were employed in solution on THV‐221 G. The homonuclear gradient correlation spectroscopy NMR measurement revealed that THV has two adjacent TFE units in addition to TFE‐HFP sequence orders. The fraction of the microstructures is quantified by the analysis of 1D solution ¹⁹F NMR spectrum. Further, the gradient heteronuclear single quantum coherence experiment helped with the clarification of chemical environments of the units TFE, HFP, and VDF. The 1D solution ¹³C NMR spectrum was helpful in clarifying sequence assignments of VDF. It is concluded that THV is a random polymer with a limited fraction of TFE‐TFE and TFE‐HFP sequence orders in addition to head‐to‐tail polymerization of VDF unit. Copyright © 2014 John Wiley & Sons, Ltd.     

Radiation-induced terpolymerization of tetrafluoroethylene with propylene and isobutylene in bulk

Terpolymerization of tetrafluoroethylene (TFE) with propylene (P) and isobutylene (iB) by γ radiation at temperatures of ?78 to 40°C, a dose rate of 5 × 10⁴?5 × 10⁵ rad/hr, and an iB/P molar ratio of 40/10?5/45 in the monomer mixture was carried out. Alternating copolymers of TFE and α-olefins, that is, P and iB, were formed at various monomer compositions. No crystalline structure was observed in the terpolymer obtained below an iB/P molar ratio of 15/35 in the monomer mixture but a partly crystalline order increased with the amounts of iB in terpolymer. The crystal lattice of the TFE–iB copolymer was affected by the introduction of P. The dose rate dependencies of the polymerization rate and inherent viscosity were 0.8 and ?0.2, respectively. The activation energy of polymerization was 2.4 kcal/mole, and the relative reactivity ratio of iB and P for a TFE radical chain end was estimated as 4.50 by the treatment of the free propagating mechanism.     

Study of synthesis and properties of tetrafluoroethylene–propylene copolymers

Bulk copolymerization of tetrafluoroethylene (TFE) with propylene (P) initiated by tert-butyl peroxybenzoate (TBPB) in the temperature interval 323–363 K, monomer pressure from 2 to 9 MPa, and TFE and P molar ratio from 20/80 to 90/10 was carried out. The effect of these reaction conditions on the yield, molecular weight, and polymer composition of the copolymer synthesized was studied. Rubber-like alternating copolymers in a wide range of monomer compositions of TFE and P (from 40 to 80 mol %) were obtained. The reaction proceeds in a stationary state without an induction period. Monomolecular chain transfer reaction (C_p = 5 × 10^?4) to propylene takes place. The relative reactivity ratio of P and TFE (0.15 and 0.01, respectively) and apparent activation energy E_α = 75.8 kJ/mol of the reaction were determined.     

19F- and 1H-NMR spectra of tetrafluoroethylene–propylene copolymers

High resolution 94-MHz ¹⁹F- and 100-MHz ¹H-NMR spectra were measured on a series of tetrafluoroethylene (TFE)-propylene (P) copolymers having a range of composition (TFE/P molar ratio = 37/63–55/45) and polymerized at different temperatures (?23, 25 and 65°C). The spectra were analyzed in relation to copolymer compositions. The assignment of ¹⁹F resonance in terms of tetrads proposed previously was confirmed, and the tentative assignment of ¹H resonances was proposed in terms of triads. The spectra thus interpreted revealed the sequence distribution of the copolymers. Copolymer compositions calculated from NMR spectra and elemental analysis agreed rather well with each other. Monomer reactivity ratios were calculated from the sequence distributions and compared with those obtained from the elemental analysis. It was observed that highly alternating copolymers are obtained in this system over a wide range of monomer composition at lower temperatures and that a deviation from alternancy increases slightly with rising polymerization temperature.     

氯乙烯/N-苯基马来酰亚胺共聚物组成控制和优化

研究了氯乙烯 /N 苯基马来酰亚胺 (VC/PMI)共聚物组成随转化率的变化 ,体系中共聚物的累积组成偏差小于 0 0 5或 0 1的单体配比范围很小 ,采用加入第三单体丙烯腈 (AN)的方法进行改善 ,并以PMI在共聚物中的累积组成偏差作为控制参数 ,得到了PMI在共聚物中的累积组成偏差小于 0 0 5和 0 1的VC/PMIlAN较优的配比范围 .结合悬浮聚合工艺的特点 ,确定了VC/PMI/AN悬浮共聚的最佳单体配比范围为f1=0 72～ 0 84 ,f2 =0 0 2～ 0 0 4 ,f3 =0 1 2～ 0 2 4 .     

Kinetic Study of Radical Polymerization VI. Copolymer Composition and Kinetic Parameters for Coplymerization of Styrene‐Itaconic Acid by On‐Line 1H‐NMR

Free radical solution copolymerization of styrene (St) and itaconic acid (IA) in dimethylsulfoxide‐d₆ (DMSO‐d₆) as the solvent and the use of 2,2′‐azobisisobutyronitrile (AIBN) as the initiator at 78°C was investigated by an on‐line ¹H‐NMR spectroscopy technique. Individual monomer conversion vs. reaction time, which was calculated from the ¹H‐NMR spectra data, was used to study the drift in monomer mixture composition vs. conversion. It was found that in general, both monomers were incorporated almost equally into the copolymer. However, when the mole fraction of IA was low, the tendency of IA toward incorporation into the copolymer chain was somewhat higher than St and by increasing the mole fraction of IA in the reaction mixture, the inverse tendency was observed. Overall monomer conversion as a function of time was calculated from individual monomer conversion data and used for the estimation of k_p /k_t ^0.5 for various monomer mixture compositions. This ratio was decreased with increasing the amount of IA in the initial feed, indicating a decrease in the rate of copolymerization. Changes in the copolymer composition vs. overall monomer conversion were investigated experimentally from the NMR spectra. This was in good agreement with the changes in monomer mixture composition vs. reaction progress. Plotting the copolymer composition vs. initial monomer feed showed tendency of the system toward alternating copolymerization.