Analytical behaviour of hydrophilic glycolmethacrylate gels with bound thiol groups

Hydrophilic glycolmethacrylate gels with side chains containing thiol groups show high sorption selectivity for Hg, Sb, Bi, As, Ag, Cu and Pt, even in 1–3 M solutions of sulfuric or hydrochloric acid. The preparation of the sorbent Spheron Thiol and the distribution coefficients for 13 ions as a function of pH are described; within the optimal pH range the distribution coefficients exceed 10⁴. The sorption capacity of the resin reached ca. 0.5–1.0 mmol Hg g^-1 in 0.05 M HCl and equilibrium was achieved within 5 min, except for arsenic and platinum in insufficiently acidic solutions.     

Application of hydride generation to the determination of trace concentrations of arsenic by inductively-coupled plasma atomic emission spectrometry

A method is described for the determination of traces of arsenic, based on sodium tetrahydroborate reduction of arsenic and introduction of the arsine formed to a relatively low-powered (1.6 kW) inductively-coupled plasma where the arsenic atomic emission is generated, Inter-element interference effects are described; many can be eliminated by addition of potassium iodide to the sample solutions, but the standard additions method is recommended for accurate arsenic determination. Potassium iodide is also used for prereducing arsenic(V) to arsenic(III). The method has a detection limit of 0.1 ng As ml^-1 and the linear calibration range spans nearly four orders of magnitude. The proposed method is applied to the determination of ng ml^-1 levels of arsenic in waste waters.     

Multielemental speciation of As, Se, Sb and Te by HPLC-ICP-MS

An anion exchange HPLC-ICP-MS procedure allowing the simultaneous multielemental speciation analysis of arsenic, selenium, antimony and tellurium has been developed. Four arsenic species (As^III, As^V, monomethylarsonic acid and dimethylarsinic acid), two selenium species (Se^IV and Se^VI) may be determined in a single run as well as one antimony (Sb^V) and one tellurium species (Te^VI). Alternatively Sb and/or Te may be used as internal standards for As and Se speciation studies. Optimisation of ICP-MS conditions led to satisfactory relative (0.01 (Sb^V) to 1.8 (Se^VI) ng ml⁻¹) and absolute detection limits (1–180 pg). Reproducibility ranged from 3.1 to 5.6% and the linearity was verified in the 0–200 ng ml⁻¹ range.     

Determination of arsenic at the picogram level by atomic absorption spectrometry with miniaturized suction-flow hydride generation

A continuous-flow hydride generator is modified and miniaturized for the determination of picogram amounts of arsenic by atomic absorption spectrometry. A 300-μl sample is dropped into a teflon cup and pumped into an alkaline sodium tetrahydroborate stream, which is acidified in a reaction coil. The evolved hydride is swept with argon through a phase separator into an electrically-heated quartz absorption cell and the absorbance is recorded. To eliminate differences in sensitivity between arsenic(III) and arsenic(V) without prereduction by potassium iodide, it is important that arsenic(V) be mixed with tetrahydroborate prior to mixing with hydrochloric acid. The method has a detection limit of 0.08 ng As ml^?1 (24 pg) and the calibrations is linear up to 50 ng As ml^?1. The relative standard deviation for 10 replicate measurements is 5.4% for 0.5 ng As ml^?1. The addition of potassium iodide and hydroxylamine is confirmed to be effective in minimizing some interferences. The sampling rate is 90 h^?1. Results for NBS biological and steel reference materials demonstrate applicability of the technique.     

Separation and determination of some trivalent metal ions using rhodamine B grafted polyurethane foam

The incorporation of rhodamine B into polyurethane foam matrix was prepared by mixing the rhodamine B with polyol (polyether) prior to the addition of diisocyanate reagent to form the polyurethane foam material. Rhodamine B grafted polyurethane foam (Rod.B-PUF) was found to be very suitable for the separation and preconcentration of trivalent metal ions e.g. bismuth (III), antimony (III) and iron (III) from thiocyanate solutions. Bismuth and antimony were separated from concentrated acid medium (1–6 M H₂SO₄). Iron (III) was separated from pH 1 to 3. The kinetics of sorption of the Bi (III), Sb (III) and Fe (III) onto the Rod.B-PUF was found to be fast, the extraction is accomplished from 5 to 10 min with average values of half-life of sorption (t_1/2) of 2.9 min. The average values of the Gibbs free energy (ΔG) for the sorption of metal ions onto Rod.B-PUF are ?6.6 kJ mol^?1, which reflect the spontaneous nature of sorption process. The sorption mechanism of the metal ion onto Rod.B-PUF was also discussed.     

Determination of arsenic and antimony in milk by hydride generation atomic fluorescence spectrometry

A highly sensitive procedure has been developed for total arsenic and antimony determination in milk samples by hydride generation atomic fluorescence spectrometry after microwave-assisted sample digestion. The discrete introduction of 2 ml of digested sample in the automated continuous flow hydride generation system allows us to reduce drastically the sample and HCl consume and to determine several elements from a same sample digestion. The method provides detection limits of 0.006 and 0.003 ng ml⁻¹, a sensitivity of 2390 and 2840 fluorescence units per ng ml⁻¹ for As and Sb respectively, and average relative standard deviation of 2.3% for As and 4.8% for Sb. The analysis of cow milk samples, obtained from the Spanish market evidenced the presence of As at concentration levels from 3.4 to 11.6 ng g⁻¹ and Sb levels from 3.5 to 11.9 ng g⁻¹, thus in a proportion near to 1:1, which is in contrast with the 10:1 natural ratio between As and Sb and could evidence the effect of the introduction of new alloys and polymer materials in the industrial process of milk. The method was validated by the comparison of data found for commercial samples by using the proposed procedure and reference methods based on dry-ashing and AFS, and microwave-assisted digestion and inductively coupled plasma mass spectrometry determination.     

化学蒸气发生-四通道原子荧光光谱法同时测定高纯金中的痕量As,Sb,Bi,Te

采用化学蒸气发生-四通道原子荧光光谱法测定了高纯金中的痕量砷、锑、铋和碲。用乙酸乙脂萃取分离金,水相还原后采用化学蒸气发生-四通道原子荧光光谱法测定高纯金中的痕量砷、锑、铋和碲。在最佳条件下,方法对As,Sb,Bi,Te的检出限分别为0.04,0.05,0.04,0.03 ng/mL(3σ);测定精密度分别为0.98,0.89,0.94,0.99%(对10 ng/mL As,Sb,Bi和Te混合标准,n=7)。方法对实际样品中的As,Sb,Bi,Te进行了同时测定,测定结果与标准方法无明显差异,各元素的加标回收率为95%～105%。     

Determination of dimethylarsinic acid in seawater in the sub-ppb range by electrothermal atomic absorption spectrometry after preconcentration on an io

Dimethylarsinate (DMA) is preconcentrated on a strong cation-exchange resin. By optimizing the elution parameters, DMA can be separated from other arsenicals and sample components, such as group I and II metals, which can interfere in the final determination. Graphite-furnace atomic absorption spectrometry is used as a sensitive and specific detector for arsenic. The described technique allows DMA to be determined in a sample (20 ml) containing a 10⁵-fold excess of inorganic arsenic with a detection limit of 0.02 ng As ml^-1.     

复杂高铋物料中铅的Na2EDTA滴定法测定

复杂高铋物料中,铋、砷、锑、锡四元素含量高且共存时会影响铅的测定。特别是铋含量高时对铅的测定影响大。实验用EDTA—酒石酸联合掩蔽铋、砷、锑、锡,在稀硫酸介质中以硫酸钾为沉淀剂,使铅生成硫酸铅钾复盐沉淀而与铋、砷、锑、锡、铁、铜、锌、铝、钴、镍等干扰离子分离,沉淀以乙酸-乙酸钠浸取,二甲酚橙为指示剂,Na2EDTA滴定法测定铅。试验进一步优化了测定条件,确定最佳条件：硫酸（1 1）加入量为7mL、硫酸钾用量为5g、煮沸时为5min、沉淀陈化时间为2h、EDTA 50g/L 加入量为10mL、酒石酸用量为0.5g,铅的回收率99.70% ～100.65%。将实验方法应用于测定复杂高铋物料中铅,标样BY0111-1与给定值一致,相对标准偏差（n=11）RSD 0.20%～0.23%,满足生产测试要求。     

A simple and sensitive continuous hydride generation system for the determination of arsenic and selenium by atomic absorption and atomic fluorescence spectrometry

The development and optimization of a continuous hydride generation system for atomic absorption spectrometry (a.a.s.) and atomic fluorescence spectrometry (a.f.s.) is described. Sodium tetrahydroborate(III) solution and sample solution are delivered by two small peristaltic pumps to a gas/liquid separator. The evolved hydrides are swept to a miniature argon/hydrogen diffusion flame burning on a borosilicate glass tube. Detection limits (2σ) obtained for arsenic are 0.8 ng ml^-1 by a.a.s. and 0.34 ng ml^-1 by a.f.s., and for selenium 0.5 ng ml^-1 by a.a.s. and 0.13 ng ml^-1 by a.f.s. Linear working ranges are typically 1–100 ng ml^-1 with a typical measurement time of 1 min per sample or standard.     

Determination of Arsenic and Phosphorus in Doped Polysilicon Layers

Abstract

The method is based on polysilicon dissolution with a water-hydrofluoric-nitric acid etchant mixture followed by matrix volatilization as hexafluorosilicic acid. Losses of arsenic through volatilization are avoided by its oxidation with permanganate. Phosphorus is determined by the molybdenum blue method with direct addition of a mixed reagent to the residue. Spectrophotometric evaluation at 882 nm provides a detection limit of 10 ng P ml^?1 with a precision better than 3%. Arsenic is determined by reducing As(V) to electroactive As(III) on addition of sulphite in 2 M hydrochloric acid. Differential-pulse polarography of this solution provides a precision of 2% and a detection limit of 20 ng As ml^?1.     

氢化物发生-原子荧光光谱法同时测定高纯铟中As、Sb

研究了氢化物发生-原子荧光光谱法测定高纯铟中微量As、Sb元素的条件,选择了适宜的反应条件以及仪器的最佳工作条件,考察了铟基体对被测元素的干扰,采用基体匹配的方法消除干扰,建立了氢化物发生-原子荧光光谱法测定高纯铟中微量的As、Sb的分析方法。As、Sb的检出限分别为0.18和0.28 ng/mL,测定下限为1.2×10-5和1.9×10-5,相对标准偏差分别为1.9%和1.7%,回收率为97.4%和103%,适用于5～6 N高纯铟中微量As、Sb的测定。     

Evaluation of continuous hydride generation combined with helium and argon microwave induced plasmas using a surfatron for atomic emission spectrometric determination of arsenic,antimony and selenium

The direct coupling of continuous hydride generation with both Ar and He microwave induced plasmas (MIP) sustained in a surfatron has been optimized for the simultaneous determination of arsenic, antimony and selenium with atomic emission spectrometry. While a discharge tube of quartz was found suitable for the Ar plasma, the use of an Al₂O₃ tube led to improved performance of the He plasma. The He MIP was found to be less tolerant to the introduction of hydrogen than the Ar MIP, and correspondingly the hydride generation should be operated at a lower flow rate of 0.5% NaBH₄ solution. The introduction of the H₂O vapour produced during hydride generation into both discharges was found to greatly decrease the sensitivities and to degrade the measurement precision. It could be effectively removed with trapping by concentrated H₂SO₄. The detection limits (3σ) for As, Sb and Se are 1, 0.4 and 1 ng ml⁻¹ with the Ar MIP, and 2, 0.3 and 6 ng ml⁻¹ with the He MIP, respectively. The calibration curves are linear over three decades of concentration. The mutual interferences from As(III), Sb(III), Se(IV), Bi(III) and Sn(IV) were found to be negligible at interferent concentrations below 1 μg ml⁻¹ and in most cases the tolerable interferent concentrations are up to 20 μg ml⁻¹. The proposed method has been applied to the determination of As, Sb and Se in tea samples at μg g⁻¹ levels.     

Simultaneous speciation of inorganic arsenic and antimony in natural waters by dimercaptosuccinic acid modified mesoporous titanium dioxide micro-column on-line separation and inductively coupled plasma optical emission spectrometry determination

A novel absorbent was prepared by dimercaptosuccinic acid chemically modifying mesoporous titanium dioxide and was employed as the micro-column packing material for simultaneous separation/preconcentration of inorganic arsenic and antimony species. It was found that both trivalent and pentavalent of inorganic As and Sb species could be adsorbed quantitatively on dimercaptosuccinic acid modified TiO₂ within a pH range of 4–7, and only As(III) and Sb(III) could be quantitatively retained on the micro-column within a pH range of 10–11 while As(V) and Sb(V) were passed through the micro-column without the retention. Based on this fact, a new method of flow injection on-line micro-column separation/preconcentration coupled to inductively coupled plasma optical emission spectrometry was developed for simultaneous speciation of trace inorganic arsenic and antimony in natural waters. Under the optimized conditions, an enrichment factor of 10 and sampling frequency of 10 h^− 1 were obtained with on-line mode. The detection limits of As(III), As(V), Sb(III), and Sb(V) are 0.53, 0.49, 0.77 and 0.71 ng mL^− 1 for on-line mode and as low as 0.11, 0.10, 0.15 and 0.13 ng mL^− 1 for off-line mode due to its higher enrichment factor (50), respectively. The relative standard deviations of two modes are less than 6.7% (C = 20 ng mL^− 1, n = 7). The concentration ratio of lower oxidation states/higher oxidation states changing from 1:10 to 10:1 has no obvious effect on the recoveries of As(III) and Sb(III). In order to validate the developed method, two certified reference materials of GSBZ5004-88 and GBW(E)080545 water sample were analyzed and the determined values are in good agreement with the certified values. The proposed method was successfully applied to the simultaneous speciation of inorganic arsenic and antimony in natural waters.     

Effect of temperature on generation and decomposition of the group Vb element hydrides and estimation of the kinetic stability of gaseous bismuth hydride by atomic-absorption spectrometry

During work on atomic-absorption determination of arsenic, antimony and bismuth by the hydride-generation method with sodium tetrahydroborate, the thermal and kinetic stabilities of the hydrides at various generation temperatures were studied. The arsenic and antimony hydrides are very stable even at 40 degrees but bismuth hydride is very unstable both thermally and kinetically, even at 25 degrees . The approximate rate constants for the decomposition of gaseous bismuth hydride at 0, 10, 25 and 40 degrees were found to be 0.05, 0.10, 0.24 and 0.29min(-1) respectively.     

Determination of arsenic and antimony in electrolytic copper by anodic stripping voltammetry at a gold film electrode

A simple procedure is described for the determination of arsenic and antimony in electrolytic copper. The copper is digested with nitric acid and copper is separated from arsenic and antimony by passing an ammoniacal solution of the sample through a column of Chelex-100 resin. After digestion with sulphuric acid and reduction to arsenic(III) and antimony(III) with sodium sulphite in 7 M sulphuric acid at 80°C, both arsenic and antimony are deposited at-0.30V and their total is determined by anodic stripping; antimony is then selectively deposited at -0.05 V for anodic stripping. The lower limits of determination are 56 ng As and 28 ng Sb per gram of copper; relative standard deviations (n = 5) are in the ranges 6.1–15.0% for 5.5—0.5 ppm arsenic in copper and 4.1–6.8% for 2.6—0.6 ppm antimony.     

Study on simultaneous speciation of arsenic and antimony by HPLC-ICP-MS

A method was developed for the simultaneous speciation of arsenic and antimony with HPLC-ICP-MS using C30 reversed phase column. Eight kinds of arsenic compounds (As(III), As(V), monomethylarsonic acid (MMAA), dimethylarsinic acid (DMAA), arsenobetaine (AB), arsenocholine (AsC), trimethylarsine oxide (TMAO) and tetramethylarsonium (TeMA)), Sb(III) and Sb(V) were simultaneously separated by the special mobile phase containing ammonium tartrate. Especially for the species of organic As, a C30 column was better than a C18 column in the effect of separation. Limits of detection (LOD) for these elements were 0.2 ng ml⁻¹ for the species of each As, and 0.5 ng ml⁻¹ for the species of each Sb, when a 10 μl of sample was injected, respectively. The proposed method was applied to a hot spring water and a fish sample.     

Determination of uranium by thermal and epithermal neutron activation in natural waters and in human urine

Uranium is determined via its ²³⁹U nuclide (74.0 keV, t_{$\text{1}\text{2}$} = 23.5 min) in natural waters down to 0.03 ng U ml^-1 after preconcentration with activated carbon and oxine; 30-min irradiation and counting times are used. No preconcentration is required for samples containing more than 4 ng U ml^-1 with 10-min irradiation and counting times. Uranium in urine can be determined under a boron shield at the 5 ng ml^-1 level after 30-min irradiation and counting.     

Separations involving sulphides : Separation of bismuth,cadmium and indium from various other elements that form thiosalts

It has been shown that 2N sodium sulphide reagent can be successfully used in separating tellurium, molybdenum, antimony or rhenium from bismuth., platinum, gold, selenium, rhenium, arsenic, molybdenum or tellurium from cadmium; platinum, gold, selenium, rhenium, arsenic, molybdenum, tellurium or antimony from indium.It is not possible to separate quantitatively arsenic, platinum, gold or selenium from bismuth; antimony from cadmium; and tin from bismuth, cadmium or indium.     

Flameless Atomic Absorption Determination of Volatile Hydrides Using Cold Trap Collection

Abstract

The hydrides of arsenic, antimony, bismuth, and selenium are collected in a liquid nitrogen cold trap and then volatilized into either an argon-entrained air-hydrogen flame or into a Perkin-Elmer HGA-2000 Graphite Furnace for atomic absorption measurement. Flameless atomization results in approximately ten-fold lower detection limits. The sensitivities and detection limits in nanograms are, respectively, 1.0 and 0.2 for arsenic, 5.6 and 1 for antimony, 2.0 and 1 for bismuth, and 40 and 10 for selenium.