数字散斑剪切干涉及偏转平台法相移系统研究

在传统的剪切电子散斑干涉中 ,直接观测到的是干涉条纹图样。因此 ,如何将位移导数场的定量信息从剪切电子散斑干涉条纹图案中提取出来 ,一直是人们关心的问题。本文运用传播光矢量对数字散斑剪切干涉的条纹形成作了理论解释 ,使其物理意义更加清晰。理论分析表明 ,物体的微小偏转可引入线性附加位相。因此 ,通过连续偏转物体可实现剪切电子散斑干涉的相移。本研究通过计算机控制载物平台的精细旋转实现相移 ,结合传统的数字散斑剪切干涉技术以及四步相移算法 ,实现了数字剪切散斑干涉相移系统。利用该系统进行了中心加载、周边固定的圆盘的典型实验 ,实验结果表明该系统可以方便有效地提取出位移导数场的定量信息。     

Experimental full field investigations of resonant vibrations for piezoceramic plates by an optical interferometry method

The experimental measurement of resonant frequencies for piezoelectric material is generally performed by impedance analysis. In this paper we employ an optical interferometry method, called amplitude-fluctuation electronic speckle pattern interferometry (AF-ESPI), to investigate the vibration characteristics of piezoceramic plates. This method demonstrates its advantages of combining noise reduction, like the subtraction method, and high fringe sensitivity, like the time-averaged method. As compared with the film recording and optical reconstruction procedures used for holographic interferometry, the interferometric fringes of AF-ESPI are produced instantly by a video recording system. Based on the fact that clear fringe patterns measured by the AF-ESPI method will be shown only at resonant frequencies, both the resonant frequencies and corresponding mode shapes are obtained experimentally at the same time. Excellent quality for the interferometric fringe patterns of the mode shapes is demonstrated. We find from experimental results that the out-of-plane vibration modes (type A) with lower resonant frequencies cannot be measured by impedance analysis and only the in-plane vibration modes (type B) will be shown. However, both the out-of-plane (bending) and in-plane (extension) vibration modes of piezoceramic plates are obtained by the AF-ESPI method. Finally, numberical finite element calculations are also performed, and the results are compared with the experimental measurements. Excellent agreement for the resonant frequencies and mode shapes are obtained from both results.     

Evaluation of rigid rotations in flexural loading tests by holographic interferometry

The authors develop a simple method based on holographic interferometry for determining the Poisson's ratio and the Young's modulus for a specimen subjected to four-point flexural testing that evaluates and eliminates the effects of the unwanted rigid-body rotations. In the experimental setup, they use an additional mirror to record the underside and the front surface of the specimen simultaneously. The theoretical analysis shows that it is possible to correlate the holographic fringe pattern of the underside and front surface of the sample. Each rotation angle can be evaluated by counting the fringe orders between two points chosen on the two fringe patterns.     

Interferometrie transparenter Phasenobjekte,insbesondere bei hohen Interferenzstreifendichten,dargestellt an einem Beispiel aus der Wärmeübertragung

The assumptions of ‘ideal interferometry’ result in formulae which are easy to use for the interpretation of interferograms, but which are only valid if the interference fringe density is low. If these formulae are used at higher fringe densities, one must focus at the so-called ‘optimal focussing plane’. If the interference fringe density becomes still greater, practically any focussing position will result in deviations from ‘ideal interferometry’. With the aid of an example from heat transfer a method is presented which enables the most favourable focussing plane to be determined and which corrects the resulting deviations from ‘ideal interferometry’ by use of an iterative algorithm.     

Surface-strain measurements on a hemispherical shell using holographic interferometry

A method is presented for using real-time fringe counting and double-exposure single-hologram interferometry to measure surface strain on pressurized hemispherical shells. An aluminum shell is employed for experimental verification of these techniques. Surface-strain variations caused by a defect in the aluminum wall are detected and measured. Strain-gage arrays are used for comparison of experimental results. Bendix Kansas City Division is a prime contractor to the Atomic Energy Commission.     

An intelligent hybrid method to automatically detect and eliminate experimental measurement errors for linear elastic deformation fields

In a previous study, to minimize or eliminate the errors and noises associated with a full-field experimental measurement and subsequent fringe analysis such as moiré interferometry, the authors derived a variational principle minimizing the experimental measurement errors. Furthemore, on the basis of this variational principle, the authors developed an intelligent hybrid method. In several test simulations, the method has demonstrated the automatic detection and elimination of randomly incorporated errors into known correct finite element displacement fields. In this study, a fringe analysis method is developed together with the two-dimensional fast Fourier transform method. Then, experimentally recorded moiré fringe patterns are analyzed by the fringe analysis method. The conventional and intelligent hybrid analyses are carried out using the analyzed fringe information as input data. The present method verifies the automatic detection of experimental errors and noises, and the simultaneous automatic elimination of those experimental errors. This method also makes it possible to obtain a fairly smooth visualization of higher order information such as the stress and strain distributions.     

一种通过条纹方向图提取散斑条纹中心线的方法

在光测力学中,如何从单幅散斑干涉条纹图中消除散斑噪声,高精度自动提取相位信息,是一项较困难的工作。本文提出了一种计算条纹方向的简单算法,以及通过条纹方向图提取散斑条纹中心线的方法。实验表明此方法对高噪声的散斑条纹图非常有效。     

A new holographic interferometer for stress analysis

In holographic interferometry with a photoelastic model, two families of fringes are generated simultaneously when the model is stressed. One family represents the isochromatic-fringe pattern normally associated with photoelasticity which yields the difference between the principal stresses. The other family represents the isopachic-fringe pattern associated with interferometry which yields the sum of the principal stresses. From these complementary patterns, the magnitudes of the principal stresses can readily be determined throughout the field of observation. Unfortunately, these fringe patterns are not completely independent but interact in such a way as to make interpretation difficult in critical regions of the model. A new system has been developed which readily permits simultaneous acquisition of these fringe patterns without their undesirable mutual interaction, as well as providing increased sensitivity. This new interferometer uses a double-pass object beam and an optical rotator to eliminate the isochromatic-fringe pattern and its effect from the isopachic interferogram. Such a system has considerable value in experimental mechanics for applications to both static and dynamic model studies and to materials investigation.     

1999 William M. Murray lecture

The history of holographic interferometry is one of problems. It has progressed from a novel discovery to a recognized technology only by the systematic pursuit of explanations for the puzzling phenomena it presents: unusual fringe patterns, fringe localization phenomena and bizarre fringe parallax. How to use the fringes to find three-dimensional deformation patterns is also a problem. Furthermore, the problem of how to handle high-volume testing spurred the evolution from photographic plates to fiexible roll film for all electronic media. Finally, the use of CCD television cameras and digital video processing has made phase-step interferometry the dominant method of fringe analysis but presents a major problem in the form of the phase-unwrapping quandary. This paper will attempt to trace the history of this technology in terms of the problems it has presented and their solutions. This paper was presented as an invited lecture at the 1999 SEM Annual Conference and Exposition, June 9, 1999, in Cincinnati, Ohio.     

The magic of carrier fringes in moiré interferometry

Practical applications in which carrier fringes are used with moiré interferometry for strain measurements are presented. Examples illustrate how moiré carrier fringes are applied to obtain the desired data in complex laminated composite specimens. In many cases, carrier fringes permit extraction of much more detailed information, with procedures that are easier and more accurate than those using loadinduced fringes alone. The fringe vector for carrier fringes is introduced and its application to the interpretation of fringe patterns is explained. In moiré interferometry, the carrier fringes are produced easily by adjustments of optical elements that control the virtual reference grating.     

Evaluation of finite-element calculations in a part-circular crack by coherent optics techniques

Two techniques, speckle photography and holographic interferometry, were used to test three-dimensional finite-element calculations in an internally pressurized cylinder with an external part-circular crack. Opening displacements along the crack line were measured by speckle photography. Radial displacements were obtained from holographic fringe patterns. Good agreement between experimental and numerical data is obtained. Stress-intensity factor variations along the crack front are calculated from numerical results.     

一种高灵敏度形状检测新技术

应用光的干涉和衍射理论，系统地阐述了一种高灵敏度形状检测技术的基本原理，并提出了一个新的测试方法，可以消除坐标影响项，从而得到纯等高线条纹图。文中应用该技术，实际测量了带有几种压痕的平板表面的深度分布，分析了测量灵敏度和精度，给出了部分实验结果。     

载波条纹图的处理及应用

本文提出一种载波条纹的处理方法，将变形前、后的载波条纹图分别经过条纹细化、抽取中心、级数编码、全场拟合等处理，首先求出全场每个像素点上的条纹级数，然后再对应相减，以得到仅仅由于变形引起的干涉条纹的全场分布，文中应用该方法分析处理了差分干涉条纹图，测量了水平热管周围的温度场、温度梯度场及壁面换热系数。     

Study of transformation plasticity in tetragonal zirconia polycrystals by moiré interferometry

Transformation plasticity in ceria-stabilized tetragonal zirconia polycrystals due to the stress-induced tetragonal-to-monoclinic martensitic transformation under tension and bending is studied by moiré interferometry. The whole fringe patterns includingu fields andv fields are acquired. According to these patterns, the distributions of transformation plasticity in transformation zones are obtained, and the phenomenon of plastic flow localization for transformation is revealed. The above work provides a significant experimental foundation for establishing transformation constitutive relations The project supported by the National Natural Science Foundation of China     

MOIRÉ INTERFEROMETRY WITH ENHANCED RESOLUTION

The implementation of this method is relatively simple. It does not require any modification to interferometric systems already in use. It can be used in the analysis of large as well as very small fields, including measurements under a microscope.
A fringe pattern with a carrier is recorded in a single exposure, just as in the standard procedure. As a consequence, any possible instability of the interferometer does not affect the accuracy of the measurements. Further, the spatial resolution of the measurements is not compromised.
Since only one exposure is needed for a given displacement component this method can be applied to dynamic as well as static measurements.
It should be emphasized that even though the number of electronically generated fringes can be arbitrary, the sensitivity is the same as in ordinary moire interferometry as long as the data are taken at the lines of minimum intensity. The improvement is in the increase of the number of data points taken at the locations of maximum resolution. In other words, all the data are taken at the maximum resolution.
This method applies not only to moire interferometry but to any experimental technique based on two-beam interference, as long as the fringe pattern has good contrast.     

利用光学干涉条纹图相位分析测量纳米位移

Optical methods such as Twyman-Green interferometry, moiré interferometry, holographic interferometry and speckle interferometry are useful to measure displacement and strain in the full-field of structures. Recently phase analysis method of fringe patterns obtained by these optical methods becomes popular, and it provides accurate quantitative results in the full-field. In this paper, in order to measure displacement and strain, real-time or high-speed nano-meter displacement measurement methods developed by the authors are introduced. That is, (1) out-of-plane displacement analysis by Twyman-Green interferometry using integrated phase-shifting method using Fourier transform phase-shifting method, (2) simultaneous two-dimensional in-plane displacement analysis by moiré interferometry and (3) out-of-plane displacement analysis by phase-shifting digital holographic interferometry. The theories and applications are shown.     

电子错位散斑研究

本文从理论上分析了错位散斑实现电子干涉的可行性,推导了摄象机光靶接收的错位散斑的光强表达式,分析了电子干涉条纹的可见度,提出并实现了电子错位散斑技术的三种方法,即实时法,双曝光法和实时时间差法。获得了位移梯度等值条纹的电子干涉图。     

Experimental observation of stress waves propagating in laminated composites

The theoretical research on stress waves propagating in laminated composites has been reported by many authors. However, there has been little work on experimental studies of stress waves in those materials. This paper presents an experimental investigation on stress waves propagating parallel to the layers of a laminated composite. A sandwich laminated composite consisting of two aluminum facings and an epoxy core is used as a specimen. The stress wave in the specimen is observed by use of high-speed holographic interferometry with a pulsed laser. In order to obtain the relative fringe orders, the interference fringe pattern in the reconstructed image is treated as an image-processing system with a personal computer. For the calculation of the in-plane displacement, an approximate relative-fringe-order method is used. The in-plane displacements obtained at some sampling points on the surface are smoothed by using a spline function. Distributions of the in-plane displacement and the shear stress are then obtained quantitatively over the whole analyzed field.     

Nano-meter Displacement Measurement by Phase Analysis of Fringe Patterns Obtained by Optical Methods

0Introduction Inordertomonitorthehealthofstructures,straingagesanddisplacementtransducersare usuallyused.Thereasonisthatmanyrulesorcodesforinspectionofstructuresrequiretousestrain gagesanddisplacementtransducers,anditiseasytousethem.However,thesemethodsarebasically one pointmeasurementmethods.Theyareexpensiveandtime consumingfordistributionanalysis.Opticalmethodssuchasgrating projection,geometricmoir啨,moir啨interferometry,holographic interferometryandspeckleinterferometryareusefultomeasuredi…     

Inversion of speckle interferometer fringes for hole-drilling residual stress determinations

Speckle interferometric fringe patterns record stress-relief displacements induced by the drilling of blind-holes into prestressed objects. The quantitative determination of residual stress state from such stress patterns is difficult because of the ambiguity in the order of the observed fringes. The plane stress magnitudes are provided directly from selected fringe positions using a stochastic, iterative least squares minimization approach. The inversion requires prior knowledge of the experimental geometry and an appropriate uniaxial stress-relief displacement basis function derived from three-dimensional finite element calculations. Superpositioning of the rotated and scaled displacement basis functions allows the stress-relief relaxation for any biaxial state of stress to be determined. In this paper, fringe patterns were forward modeled from a large ensemble of calculated biaxial stress-relief displacement fields. Inversion of these noise-free fringe patterns reproduced the biaxial stresses with negligible error. Analysis of more realistic fringe patterns that include speckle noise gave stress magnitude errors that diminished rapidly with the number of selected points to better than 3 percent for 100 points. Sensitivity of the optical method is influenced by a number of factors, but the ensemble of model fringe patterns studied indicates that the stress magnitudes (nomalized with respect to the material's Young's modulus) from 3×10^–4 to 10^–2 can accurately be determined with visible laser radiation. The method is amenable to automation and can easily be extended to study near surface gradients in the residual stresses or applied to other optical recording techniques such as moiré and phase-shifting interferometry.