Tuneable Sagnac comb filter including two wave retarders

In this paper we study theoretically and experimentally a wavelength-tuneable Sagnac birefringence filter. The device is a Sagnac interferometer including a symmetric fibre coupler and a length of high-birefringence fibre in the loop. A wave retarder is inserted at each end of the birefringent fibre for absolute wavelength tuning. We show theoretically that wavelength tuning through wave plate orientation ensuring constant amplitude of the filtering function is possible only if a minimum of two wave retarders are included in the setup. The position of the transmission peaks then varies linearly with the angle of one of the retarders and can be adjusted over one entire channel spacing. This happens only when a quarter-wave retarder and a half-wave retarder are used, if the former is oriented at 45° with respect to the fibre birefringence axes, while the orientation of the latter serves as the adjustment parameter. The theoretical predictions are confirmed by the experimental results.     

Ultra-wide bandwidth wavelength selective couplers based on the all solid multi-core Ge-doped fibre

A novel wavelength selective coupler based on the all solid nine-core Ge-doped fibre has been proposed. The wavelength selective coupler is based on the phenomenon of a multi-core coupling. All the cores are made of Ge-doped silica and the index of central core is larger than the outer core. At the fixed fibre length, the different wavelength can be selected. The performances of coupling and propagation characteristics have been numerically investigated by using a full beam propagation method (BPM). Simulation results show that the all solid nine-core Ge-doped fibre can achieve simultaneous shorter coupler length and wideband filtering characteristics. The 0.763 mm and 0.745 mm wavelength selective coupler are proposed to achieve different wavelength division and the bandwidth is up to the 400 nm, and 300 nm, respectively.     

An integrated optical coupler used in a fibre interferometry system for on-line surface measurements

In this paper, an integrated optical (IO) coupler produced using the technique of silica-on-silicon was described. A fibre interferometry system using the IO coupler was then developed and its performance was tested. The environmental noise and disturbances in this system were reduced significantly after combining a reference interferometer and an all fibre polarisation scrambler so as to produce good stability and repeatability. Furthermore, the measurement mirror was mounted on a piezoelectric transducer (PZT) and disturbances were introduced in the system in order to simulate on-line surface measurements. Both a commercial fibre and the IO couplers were compared using this method. Better experimental results were achieved when the system using the IO coupler than using the fibre one.     

Compensation for depolarisation by a fibre coil in the presence of self-phase modulation

We report on the dependence of the degree of polarisation of an 80 fs pulsed laser beam propagating through a length of a single-mode birefringent fibre on the illumination power. Due to the birefringence and the nonlinear effect of self-phase modulation, the measured depolarisation dependence is oscillatory. It is, however, demonstrated that the oscillatory depolarisation can be compensated for by introducing a loop into the fibre geometry, which maintains the degree of polarisation of the pulsed beam as high as 90%.     

Switchable and tuneable multi-wavelength Er-doped fibre ring laser using Sagnac filters

We demonstrate experimentally a simple configuration to perform wavelength-tuning and multi-wavelength operation in a fibre ring laser that is composed of an Erbium-doped fibre and includes a fibre-optic Sagnac interferometer as a spectral filter. We consider three different Sagnac filters including a 3 dB coupler, two wave retarders (WRs) and respectively 7 cm, 1 and 7 m of high birefringence fibre. The transmission spectrum of each filter is sinusoidal with a 70, 6, and 0.85 nm period, and its maxima can be shifted over one period by adjusting the angle of the retarders in the loop. By adjusting the WRs included in the filter and in the laser ring, tuneable single wavelength and several two- or three-wavelength lasing regimes were observed. In particular, fine adjustments of the WRs allow observing two- and three- wavelength operation with wavelength separations well below the homogeneous bandwidth of the gain medium. The stability of these modes of operation however strongly depends on environmental conditions at room temperature.     

GaInAsSb/AlGaAsSb lasers in the wavelength range between 2.73 μm and 2.93 μm

Compressively strained multiple quantum well lasers in the GaInAsSb/AlGaAsSb material system are reported. Indium concentrations between 40% and 47.5% were chosen for the GaInAsSb quantum wells. Compressive strains varied between 1.16% and 1.43%. The lasers worked continuous wave at room temperature up to a wavelength of 2.81 μm. For a laser with 2.93 μm wavelength continuous wave operation was found up to a temperature of −23°C. This laser worked in pulsed operation at 15°C.     

Cavity operation of a pulsed C13H3F laser

Cavity operation of an optically pumped, pulsed, C¹³H₃F far-infrared laser is described. The use of a Fabry-Perot output coupler has resulted in selectable line emission at 1222, 1207, 1006, 388 and 412 m with power levels in the 1–20 kW range. In addition, single mode operation on the longer wavelength lines has been achieved. Experimental evidence is also presented for a collisionally coupled two-photon absorption process which is responsible for the observed short wavelength emission.     

Dynamic nuclear polarisation via the integrated solid effect I: theory

In the hyperpolarisation method known as dynamic nuclear polarisation (DNP), a small amount of unpaired electron spins is added to the sample containing the nuclear spins and the polarisation of these unpaired electron spins is transferred to the nuclear spins by means of a microwave field. Traditional DNP uses weak continuous wave (CW) microwave fields, so perturbation methods can be used to calculate the polarisation transfer. A much faster transfer of the electron spin polarisation is obtained with the integrated solid effect (ISE) which uses strong pulsed microwave fields. As in nuclear orientation via electron spin locking, the polarisation transfer is coherent, similar to the coherence transfer between nuclear spins. This paper presents a theoretical approach to calculate this polarisation transfer.

ISE is successfully used for a fast polarisation transfer from short-lived photo-excited triplet states to the surrounding nuclear spins in molecular crystals. These triplet states are strongly aligned in the photo-excitation process and do not require the low temperatures and strong magnetic fields needed to polarise the electron spins in traditional DNP. In the following paper, the theory is applied to the system naphthalene-h₈ doped with pentacene-d₁₄ which provides the photo-excited triplet states, and compared with experimental results.     

Dynamic nuclear polarisation via the integrated solid effect II: experiments on naphthalene-h8 doped with pentacene-d14

In dynamic nuclear polarisation (DNP), also called hyperpolarisation, a small amount of unpaired electron spins is added to the sample containing the nuclear spins, and the polarisation of these unpaired electron spins is transferred to the nuclear spins by means of a microwave field. Traditional DNP polarises the electron spin of stable paramagnetic centres by cooling down to low temperature and applying a strong magnetic field. Then weak continuous wave microwave fields are used to induce the polarisation transfer. Complicated cryogenic equipment and strong magnets can be avoided using short-lived photo-excited triplet states that are strongly aligned in the optical excitation process. However, a much faster transfer of the electron spin polarisation is needed and pulsed DNP methods like nuclear orientation via electron spin locking (NOVEL) and the integrated solid effect (ISE) are used.

To describe the polarisation transfer with the strong microwave fields in NOVEL and ISE, the usual perturbation methods cannot be used anymore. In the previous paper, we presented a theoretical approach to calculate the polarisation transfer in ISE. In the present paper, the theory is applied to the system naphthalene-h₈ doped with pentacene-d₁₄ yielding the photo-excited triplet states and compared with experimental results.     

Single-wavelength pulsed optical logic based on dichroism in CdS

A new type of pulsed (picosecond) nonlinear optical logic element, that exploits polarisation dichroism, is proposed and investigated experimentally. The device is based on a nonlinear Fabry-Pérot cavity and excite/probe operation. Unlike previous similar devices, it operates at a single wavelength and uses band-edge dichroism to distinguish the excite and probe pulses according to their polarisation. The concept has been tested using CdS as the dichroic nonlinear material and differential gain levels greater than unity have been observed. Experimental data are also included regarding the magnitudes of the nonlinear refractive cross-section and other relevant parameters in CdS.     

Er-doped twin-core fibre coupler as a saturable-absorber-based narrow-band filter for fibre lasers

We have proposed and demonstrated experimentally that an Er-doped twin-core fibre (ErTCF) can be employed as a tracking narrow-band filter in fibre ring lasers for line narrowing and enhancement of the spectral stability. The device mimics a saturable absorber with inhomogeneous broadening. The slow erbium ion saturation dynamics in the ErTCF prevents wavelength hopping whilst it enables the filter to track the operation wavelength on its tuning. We have improved the device operation by utilizing the inherent filtering effect of a twin-core fibre coupler. Presented at the 1st Czech-Chinesse Workshop “Advanced Materials for Optoelectronics”, Prague, Czech Republic, June 13–17, 1998 This research has been in part supported by the Commission of the European Union in the frame of Copernicus programme, Project # 7882 and by the Ministry of Education of the Czech Republic under Contract OC 241.10/1998.     

Multi-wavelength bismuth-based erbium-doped fiber laser based on four-wave mixing effect in photonic crystal fiber

A stable multi-wavelength erbium-doped fiber laser based on four-wave mixing (FWM) in a photonic crystal fiber (PCF) is demonstrated in this paper. The phase matching condition for four-wave mixing in the photonic crystal fiber has been enhanced using a seed signal and a polarisation controller to control the states of polarisation in the ring laser cavity. At a maximum pump power of 1480 nm, 5 lines are observed with nearly 2.15 nm spacing between the lines, and with a signal to noise ratio of more than 20 dB. The number of channels and wavelength spacing can be controlled by varying the output coupler ratio.     

Design of tunable asymmetric directional coupler filter using periodically segmented Ti:LiNbO3 waveguides

A tunable wavelength filter is designed using Ti:LiNbO₃ asymmetric directional coupler. One arm of the directional coupler is made of continuous waveguide while the other arm is periodic segmented. This segmentation reduces the lithographic steps and hence the fabrication cost required for such asymmetric coupler based filter. The propagation constant of periodical segmented and continuous waveguides are analysed using Effective-Index-based Matrix Method. The tunability is achieved using electro-optic property of LiNbO₃.     

All-optical 2R-regeneration and continuous wave to pulsed signal wavelength conversion based on fiber nonlinearity

In this paper, we propose a novel all-optical 2R (re-amplification and re-shaping) regenerator based on inducing nonlinear chirp over a continuous wave probe. The regenerator also performs continuous wave to pulsed wavelength conversion. The chirp is induced in a highly nonlinear fiber by the data modulated pulsed signal that is to be regenerated. Offset filtering is employed at the output of the highly nonlinear fiber to extract the frequencies generated as a result of chirping. The regenerator performance has been evaluated with the help of bit-error-rate plots and eye diagrams at different values of optical signal to noise ratios. Apart from re-shaping and re-amplification, inclusion of the regenerator results in better resilience to amplified spontaneous emission noise.     

Graphical Representation of the Supermode Theory of a Waveguide Directional Coupler

A novel graphical representation of the supermode theory of a waveguide directional coupler based on phasor analysis is described. Following this approach, dependence of the magnitudes and phases of the output fields on the splitting ratio of a directional coupler is discussed. Both the cases of phase-matched (identical) and non-phase-matched (non-identical) waveguides constituting a directional coupler are investigated. This approach directly illustrates the fact that the phase shift suffered by the coupled light relative to the throughput light is π/2, regardless of the splitting ratio for identical guides, which is not the case for couplers with non-identical waveguides. It also yields additional information about the phases of the output fields of a directional coupler. The usefulness of this approach in the context of wavelength-flattened couplers, wavelength division multiplexing couplers, and polarization effects in directional couplers is also discussed. This approach should also be helpful in the analysis of guided wave interferometric devices such as wavelength interleave filters and modulators, based on concatenated directional couplers.     

Tunable optical add-drop multiplexer based on long-period fiber gratings for coarse wavelength division multiplexing systems

We propose and experimentally demonstrate a voltage-controllable add-drop multiplexer with a tunable coupler based on long-period fiber gratings (LPFGs). The tunable coupler is based on cladding mode coupling between two parallel LPFGs with divided coil heaters, which controls the resonant wavelength positions of the two LPFGs. The wavelength tunability of the tunable coupler is measured to be -0.45 nm/degrees C in the temperature range from 20 to 120 degrees C. The large tuning range of optical signals (approximately 50.54 nm) from 1502.32 to 1552.86 nm, which covers both the short (S) and the conventional (C) bands, is achieved. The channel isolation is as high as approximately 40 dB. It has several advantages, including a broad tuning range of wavelength in both the S- and C-bands, high channel isolation, no backreflection, and so on.     

基于LiNbO_3的长周期波导光栅可调谐耦合器的设计

设计了一种基于LiNbO_3的长周期波导光栅可调谐耦合器.该耦合器利用长周期光栅的独有特性将输入波导的导模经包层模耦合至输出波导导模.由于LiNbO_3的电光效应,波导光栅芯层与包层的有效折射率随外加电压变化,从而耦合器的谐振波长及耦合效率可由外加电压调谐.分析了光栅周期与耦合器的长度对耦合器带宽和耦合效率调谐范围的影响,以及波导尺寸对谐振波长调谐灵敏度的影响.结果表明光栅周期越短,耦合器长度越长,则耦合器的带宽越窄,耦合效率调谐范围也越大.此外,谐振波长调谐灵敏度随波导宽度的增加而减小,而波导厚度对谐振波长调谐灵敏度的影响可以忽略.对光栅周期为94μm、长度为3.52cm的耦合器进行仿真,结果表明,谐振波长灵敏度为26.2pm/V,3dB带宽可达4.5nm,当外加电压从0变化到200V时,谐振波长变化5.24nm,耦合效率可在1到0.15之间进行调谐.     

Long period gratings written into a photonic crystal fibre by a femtosecond laser as directional bend sensors

A series of symmetric and asymmetric LPGs were inscribed in photonic crystal fibre by a low repetition rate femtosecond laser system. The asymmetric LPGs were found to be spectrally sensitive to bend orientation, with some of the attenuation bands producing both red and blue wavelength shifts, whilst the symmetric devices produced only a unidirectional wavelength shift. Both sets of devices displayed strong polarisation dependence.     

Q-switching an all-fiber laser using acousto-optic null coupler

A new method for Q-switching an all-fiber laser is presented. It is based on induced acoustic long period grating operating on a null coupler, which acts as acoustically controlled tunable output coupler. Q-switching is achieved by switching on and off the acoustic wave in a burst mode, thereby generating laser pulses that are ~400 times shorter than the acoustically controlled coupler’s rise time. Output pulse energy of 22 μJ and temporal width of ~100 ns were measured at a wavelength of 1.54 μm.     

包层泵浦的铒镱共掺光纤激光高效产生的实验研究

利用尾纤输出的977nm高亮度多模半导体激光器包层泵浦铒镱共掺双包层光纤,采用非球面透镜组耦合方式,使泵浦耦合效率达66%以上,并在法布里-珀罗激光振荡腔结构中实现了高效的连续激光产生,双包层光纤长度为2m,在泵浦入纤功率为1.36W时,输出连续功率最大394mW,斜率效率达35%,激光输出波长1.565μm.