10-6-10-4m2/s黏度液体中靶受力学作用的测试与分析

通过自行研制的光纤传感器对不同黏度液体中材料靶后的力学作用进行研究,获得了液体黏度变化对等离子体烧蚀力、射流冲击力及空泡生存周期的影响. 实验结果表明:液体黏度相同时,靶材所受冲击力幅值随作用激光能量的增加单调上升;液体黏度增加时,靶材所受的冲击力减小,靶材的空化空蚀程度亦减小;受液体黏度增大的影响,空泡膨胀或收缩过程减缓,相应的生存周期也增大. 此外,对空泡溃灭周期公式进行修正,结果表明修正后的理论估算值与实验值的一致性较好.     

黏性液体中激光空泡脉动特性的理论和实验研究

通过自行研制的光偏转测试系统对黏性液体中激光空泡脉动特性进行了实验，获得了激光等离子体空泡前两次脉动全过程，从而判定了空泡在脉动过程中对应的最大和最小泡半径；并将不同黏性系数下空泡脉动结果与基于空泡溃灭理论的计算结果进行了对比.结果表明：液体黏性对空泡生存周期、空泡半径，以及泡壁的运动速度等均有影响.受液体黏性影响，空泡膨胀或收缩过程明显变缓，其相应的生存周期也越长.这一研究结果不仅可促进空化研究的深入，也可为合理利用空化现象提供参考. 关键词： 激光泡 脉动特性 黏性 光纤传感器     

环境压强对空泡脉动特性的影响

基于空泡生长和溃灭理论分析不同环境压强对空泡膨胀的最大泡半径、收缩的最小泡半径、膨胀与收缩速度的影响.同时,利用高功率激光与液体物质相互作用产生空泡,采用高速照相机、高频测量水听器实验研究不同环境压强下液体中空泡运动规律,并将实验结果与计算结果进行对比.结果表明:环境压强对空泡脉动特性有较大影响.相同激光能量击穿液体介质时,随着外界环境压强的增加,空泡脉动周期呈现递减趋势;空泡第一次脉动的最大泡半径同脉动周期的变化趋势一致,且数值由快到慢递减;随着外界压强的增加,空泡溃灭的速度越快.随着压强的增大,空泡膨胀与收缩更为剧烈,持续时间更短.     

其他应用

TN249 2004064207 激光水下打靶力学效应的测试与分析=Mechanicaleffects during pulsed laser and metals interaction in water[刊,中]/徐荣青(南京理工大学应用物理系.江苏,南京(210094)),陈笑…∥光电子·激光.一2004,15(5).一599-603 采用自行研制的光纤力学传感器研究了在不同能量的脉冲激光作用下水中靶材的力学效应。实验和理论分析研究结果表明,水中靶材依次受到激光烧蚀压力及空泡溃灭产生两次射流冲击力的作用,冲击力幅值随作用激光能量的增加均先上升后下降;而射流产生时刻及空泡溃灭时刻随激光能量增加呈单调递增趋势;且射流产     

用于瞬态力学量测试的光学传感器设计及应用

基于光纤耦合反射式光束偏转法,提出了一种可用于瞬态力学量测试的光学传感器,并详细给出了该测试机理.采用该传感器,在靶材对心处实时检测到由于空泡在固体靶材附近溃灭时射流冲击力引起的靶材瞬态微小变形.通过对该传感器定标可以进一步得到作用冲击力大小.这种传感器的应用将有助于了解激光诱导产生空泡射流运动特性及其对靶材的损伤机制.     

块体非晶合金Zr55Cu30Al10Ni5 结构弛豫的研究

应用同步辐射小角x射线散射和差示扫描量热分析对块体非晶合金Zr55₅₅Cu 30₃₀Al10₁₀Ni5₅结构弛豫进行了研究.实验结果表 明：经340℃、不同时间退火后的非晶内 部的电子密度涨落随退火时间的延长先增大而后减小；玻璃转变温度附近焓弛豫峰的表观激 活能则随退火时间的延长先减小而后增大.结果反映了随退火时间的延长，块体非晶合金内 部类液体区不断减少及类固体区不断增加的过程. 关键词： 小角x射线散射 块体非晶合金 结构弛豫     

圆锥边界附近激光空泡溃灭行为的研究

为了研究刚性圆锥边界锥角对激光空泡溃灭行为的影响,文章建立了虚拟平面边界模型, 同时采用阴影摄影术、光偏转法以及数值计算的手段对边界附近空泡溃灭过程进行了研究. 结果表明边界的锥角对空泡的形状、溃灭时间以及液体射流形成均有明显影响. 空泡形状偏离球形的程度和溃灭时间均随锥角的增大而增大,且增大锥角度可以促使射流的形成. 空泡溃灭时间的实验值同理论值具有较高的一致性,验证了虚拟平面边界假设及无量纲距离修正的有效性.     

BF自由基X1∑+和a3∏态光谱常数和分子常数研究

采用内收缩多参考组态相互作用方法和相关一致基aug-cc-pV6Z, 对BF自由基X¹∑⁺和a³∏ 态的势能曲线进行了研究. 计算是在0.095---1.33 nm的核间距内进行的. 为获得更准确的结果, 计算中还考虑了Davidson修正、相对论修正及核价相关修正对势能曲线的影响. 相对论修正采用的方法是二阶DouglasKroll哈密顿近似, 修正计算是在cc-pV5Z基组水平上进行的. 核价相关修正使用的是cc-pCV5Z基组. 利用得到的势能曲线, 拟合出了各种修正下BF自由基X¹∑⁺和a³∏ 态的光谱常数D_e, R_e, ω_e, ω_ex_e, ω_ey_e, B_e和α_e、并与实验结果进行了比较. 结果表明: 考虑Davidson修正、相对论修正和核价相关修正后得到的光谱常数最接近实验结果. 利用修正后的势能曲线, 通过求解径向振转Schrödinger方程, 找到了转动量子数J = 0时这两个电子态的全部振动态, 并计算了每一电子态前20个振动态的振动能级、惯性转动常数和离心畸变常数, 其值与已有的实验结果较为一致. 本文得到的光谱常数和分子常数达到了很高的精度, 能为进一步的光谱实验提供可靠的参考.     

靶材偏置低电压对激光等离子体诱导靶上电势信号的影响

针对激光等离子体在Cu靶上诱导产生的电势信号展开实验研究，主要讨论了靶材偏置低电压时对电势信号的影响. 实验结果表明，外加低电压时，靶上电势信号呈现单峰脉冲结构，且靶材偏置负压时为正脉冲，偏置正压时为负脉冲，脉冲幅值随偏置电压增大而增大. 通过对靶上电势信号演化特性的详细分析，从等离子体荷电效应出发，结合靶材偏压造成的电场效应成功解释了靶材偏压对靶上电势信号的影响.     

液体流动条件下毛细管管口气泡动力特性实验

通过对液体流动条件下毛细管管口气泡生长及脱离过程进行可视化实验.分析了毛细管管壁浸润性,液体流速以及气体流量对气泡生长脱离过程的影响.实验结果表明:随着液体流速的增大,液体对气泡的横向剪切力增大,气泡的脱离周期减小,气泡的脱离直径也随着减小.同时,实验还发现随着气体流量的增大,使气泡生长动力增大,气泡的脱离周期减小;另外,实验还揭示出毛细管管壁浸润性的改变,将导致气泡生长过程中气固液三相接触线发生径向迁移.     

固体壁面附近激光空泡的动力学特性研究

关键词：     

Optical investigation of cavitation erosion by laser-induced bubble collapse

By means of a new force sensor based on optical beam deflection (OBD), the mechanical effects of laser-matter interaction underwater at different incident laser energy are investigated in detail. The experimental results show that a target underwater is impacted in turn by laser-plasma ablation force and high-speed liquid-jet impulse induced by bubbles collapse in the vicinity of a solid boundary. Furthermore, the amplitudes of the two forces increase monotonously with laser energy. According to the ablation force detected by the experiment and the theoretical relationship between laser intensity and ablation pressure, the value of liquid-jet impact against a solid boundary can be easily obtained. In addition, based on the model of a collapsing bubble, some characteristic parameters, such as the liquid-jet impact velocity, the maximum bubble radius, the bubble energy can also be obtained at different laser energy, which are valuable in the corresponding research fields.     

表面张力对固壁旁空泡运动特性影响的理论和实验研究

表面张力是影响空泡脉动及空蚀的一个重要因素.对五种不同表面张力液体中空泡脉动（膨胀和收缩）过程进行了研究,并将实验结果与基于空泡生长和溃灭理论的计算结果进行了对比.实验中,用激光作为测试光源,采用光偏转测试系统研究了不同表面张力液体中空泡泡壁运动规律及泡壁速度的变化.结果表明：表面张力对空泡膨胀过程起抑制作用,故液体表面张力愈大,空泡能达到的最大直径越小;表面张力对空泡的收缩过程则起加速作用,液体表面张力愈大,收缩越迅速,空泡泡壁运动速度越大,其所产生的瞬时溃灭压强越大,空化效果越好. 关键词： 表面张力 空泡 光偏转     

Nanosecond pulsed laser ablation of silicon in liquids

Laser fluence and laser shot number are important parameters for pulse laser based micromachining of silicon in liquids. This paper presents laser-induced ablation of silicon in liquids of the dimethyl sulfoxide (DMSO) and the water at different applied laser fluence levels and laser shot numbers. The experimental results are conducted using 15 ns pulsed laser irradiation at 532 nm. The silicon surface morphology of the irradiated spots has an appearance as one can see in porous formation. The surface morphology exhibits a large number of cavities which indicates as bubble nucleation sites. The observed surface morphology shows that the explosive melt expulsion could be a dominant process for the laser ablation of silicon in liquids using nanosecond pulsed laser irradiation at 532 nm. Silicon surface’s ablated diameter growth was measured at different applied laser fluences and shot numbers in both liquid interfaces. A theoretical analysis suggested investigating silicon surface etching in liquid by intense multiple nanosecond laser pulses. It has been assumed that the nanosecond pulsed laser-induced silicon surface modification is due to the process of explosive melt expulsion under the action of the confined plasma-induced pressure or shock wave trapped between the silicon target and the overlying liquid. This analysis allows us to determine the effective lateral interaction zone of ablated solid target related to nanosecond pulsed laser illumination. The theoretical analysis is found in excellent agreement with the experimental measurements of silicon ablated diameter growth in the DMSO and the water interfaces. Multiple-shot laser ablation threshold of silicon is determined. Pulsed energy accumulation model is used to obtain the single-shot ablation threshold of silicon. The smaller ablation threshold value is found in the DMSO, and the incubation effect is also found to be absent.     

Effect of environmental media on ablation rate of stainless steel under femtosecond laser multiple raster scans

We investigate the influence of environmental media on ablation rate of AISI 443 stainless steel under femtosecond(fs) laser single raster scan and multiple raster scans in air, water, and methanol. Meanwhile, the development of ablation rate with the change of fs laser-induced surface morphology in the three environmental media is comparatively studied. The results show that environmental media as well as fs laser-induced morphology control the ablation rate with the increasing number of raster scans(N). Under single raster scanning(N = 1), the ablation rate is higher in liquid than in air due to the confinement of plasma, laser-induced shockwaves, and bubble-related mechanical forces. However, under multiple raster scans, the variation in ablation rate with the increase in N in these three environmental media is complicated and is largely determined by the surface morphology induced by previous fs laser ablation. When N > 20, the ablation rate is much higher in air than in liquids due to preferential ablation caused by the formation of nanostructures-textured mound-shaped microstructures in air. Besides, the redeposition of ejected ablated materials is also an important factor that affects the ablation depth.     

激光烧蚀水下金属产生冲击波和空泡效应的研究

采用自行研制的高灵敏度光束偏转测试系统,对脉冲激光烧蚀水下金属产生的等离子体冲击波和空泡效应进行了实验研究。实验得到了激光等离子体冲击波的传播规律、冲击波与激光空泡的分离过程、空泡的脉动特性以及空泡溃灭冲击波的形成机制。结果表明,空泡最大和最小泡径、振荡周期均随着脉动次数的增加呈减小趋势,且减小幅度较大。最小收缩泡径由泡能和腔内含气量共同决定。在同一次脉动过程中,空泡膨胀所需的时间明显大于收缩所需的时间。     

Nanoparticle formation during laser ablation of solids in liquids

The experimental data on the generation of metal and semiconductor nanoparticles during their laser ablation in liquids is reviewed. The dependence of the morphology of noble metal nanoparticles on the liquid type and laser parameters is discussed. The data on the kinetics of the formation of alloyed Au-Ag nanoparticles under laser irradiation of a mixture of colloid solutions of individual nanoparticles are presented. The effect of femtosecond laser beam self-action during metal ablation in liquids via the second harmonic generation at Ag nanoclusters is discussed. The data on the generation of core-shell nanoparticles during laser ablation of alloys and in the presence of the chemical interaction of formed nanoparticles with surrounding liquid are presented. It was shown that laser ablation of CdS and ZnSe crystals leads to the formation of quantum dots of these semiconductors in solution. The parameters controlling the properties of nanoparticles during ablation in liquids and possible applications of the method are discussed.     

气泡碰壁受力模型和反弹规律

对Mo=10-8~10-12及Re=5~750范围内的上升气泡与壁面垂直碰撞问题进行了理论求解，研究了不同控制参数下气泡碰壁反弹的规律.气泡上升和碰撞过程的运动方程考虑了浮力、液体阻力、附加质量力和与壁面碰撞时引起的薄膜诱导力.气泡碰壁过程气泡界面与壁面形成的液膜厚度变化规律由Stokes-Reynolds方程计算得到.膜内气泡变形引起的流体压强采用Young-Laplace方程求解.结果表明，基于SRYL方程的薄膜诱导力模型可以很好地预测不同Reynolds数下气泡0到多次的反弹轨迹，计算结果与实验结果吻合良好.气泡在碰壁反弹过程中会形成丰富的薄膜形状，如酒窝状变形，丘疹状变形和涟漪状变形.气泡界面变形会引起膜内压强的变化，压强的分布规律与气泡界面形状有着重要的关系.气泡在与壁面碰撞的过程中，薄膜诱导力会起主导作用，且随着Reynolds数的增加薄膜诱导力最大量级增大.气泡碰撞壁面时，反弹次数与Reynolds数有着直接的联系，不同Morton数下的气泡均在相同Reynolds数附近发生气泡反弹次数的变化.      

Dynamic modeling of submerged nanoparticle pushing based on atomic force microscopy in liquid medium

This article introduces a theoretical analysis of submerged nanoparticle manipulation in liquid medium using the atomic force microscopy, and gives a review of the major differences between dry and submerged manipulation processes. In this regard, the manipulation is modeled by adding the influences of the hydrodynamic forces surface forces to the manipulation model in dry air. Then, the pushing of a gold nanoparticle of 50-nm radius on a silicon substrate at a velocity of 100 nm/s is simulated, and the dynamic behaviors of the tip and nanoparticle are investigated. The results show that, in water (as compared to air), the required manipulation force and time for nanoparticle sliding and rolling increase by 3.5 and 6.5%, for sliding and 2 and 4.3% for rolling, respectively. Also, in liquids with different viscosities, the critical values related to sliding and rolling have a maximum variation of 17 and 32% for the manipulation time, and 6 and 22% for the manipulation force, respectively, as compared to the critical values related to particle manipulation in air. Moreover, for various submerged lengths of the cantilever in water, the critical values related to sliding and rolling show a maximum time variation of 9 and 10.5%, and 7 and 7.2% (for the manipulation force), respectively. Qualitative comparisons between the obtained results and those of the existing experimental investigations show the advantages of the liquid medium for the manipulation purposes.     

Creation of silicon nanocrystals using the laser ablation in liquid

The method for the formation of silicon nanoparticles by picosecond laser pulses is studied upon the surface irradiation of the single-crystal silicon in various liquids. The ablation products are investigated using the atomic-force microscopy and Raman spectroscopy. The experimental results indicate the crystal-line structure of nanoparticles and the dependence of their size on the ablation medium.