Influence of MnO_2 on the photocatalytic activity of P-25 TiO_2 in the degradation of methyl orange

Influences of α-MnO2, β-MnO2, and δ-MnO2 on the photocatalytic activity of Degussa P-25 TiO2 have been investigated through the photocatalytic degradation of methyl orange. The TiO2 photocatalyst, before and after being contaminated by MnO2, was characterized by UV-visible diffuse reflectance spectroscopy (UV-vis DRS), photoluminescence (PL), and X-ray photoelectron spectroscopy (XPS). The results showed that photocatalytic activity of TiO2 could be inhibited significantly or completely deactivated due to the presence of even a small amount of MnO2 particles. It was found that the poisoning effect varied with the crystal phases of MnO2 and the effect was in the order δ-MnO2 >α-MnO2 >β-MnO2. The poisoning effect was attributed to the formation of heterojunctions between MnO2 and TiO2 particles. The heterojunctions changed the chemical state of Ti4 and O2 sites in the crystalline phase of TiO2. MnO2 in contact with TiO2 particles also broadens the band-gap of TiO2, which decreases UV absorption of TiO2. It can also create some deep impurity energy levels serving as photoelec-tron-photohole recombination center, which accelerates the electron-hole recombination.     

Fabrication,Characterization and Optical Properties of TiO2 Nanotube Arrays on Boron-doped Diamond Film Through Liquid Phase Deposition

TiO2 nanotube（TiNT） arrays were deposited on boron-doped diamond films by a liquid-phase deposition method with ZnO nanorod arrays as the template.The different morphologies of TiNTs have been obtained by controlling the morphology of ZnO template.The X-ray diffraction and energy-dispersive X-ray analysis show that the ZnO nanorod array template has been removed in the TiNTs formation process.The crystalline quality of the TiNTs is improved by increasing the annealing temperature.The band gap of the TiNTs is about 3.25 eV estimated by the UV-Vis absorption spectroscopy,which is close to the value of bulk TiO2.In the photoluminescence spectrum,a broad visible emission in a range of ca.550-750 nm appears due to the surface oxygen vacancies and defects.     

Improving ferro- and piezo- electric properties of hydrogenized poly(vinylidene fluoride-trifluoroethylene) films by annealing at elevated temperatures

After annealing the solution cast P(VDF-TrFE) films at elevated temperatures, which were synthesized via a full hydrogenation process from P(VDF-CTFE) with a composition of VDF/TrFE = 80/20(mol%), a series of P(VDF-TrFE) films were fabricated in present work. The crystalline and ferroelectric phases of the films were carefully characterized and their dielectric, ferroelectric and piezoelectric properties were systematically investigated. The improved crystalline and ferroelectric phases in the films induced by annealing at elevated temperatures are responsible for the significant improved electric properties of the films. The optimized annealing temperature is found to be 130 °C and the best performance including the highest dielectric constant of 12.5 at 1 kHz, the largest maximum polarization of 11.21 μC/cm~2 and remnant polarization of 7.22 μC/cm~2, the lowest coercive electric field of 56 MV/m, and the highest piezoelectric coefficient of -25 pC/N is observed.     

Slow Down Dewetting in Polymer Films by Isocyanate-treated Graphite Oxide

Isocyanate-treated graphite oxides(i GOs) were well-dispersed into the polystyrene(PS) thin films and formed a novel network structure. With control in fabrication, an i GOs-web layer was horizontally embedded near the surface of the films and thus formed a composite slightly doped by i GOs. This work demonstrated that the i GOs network can remarkably depress the dewetting process in the polymer matrix of the composite, while dewetting often leads to rupture of polymer films and is considered as a major practical limit in using polymeric materials above their glass transition temperatures(Tg). Via annealing the 50–120 nm thick composite and associated neat PS films at temperatures ranging from 35 °C to 70 °C above Tg, surface morphology evolution of the films was monitored by atomic force microscopy(AFM). The i GOs-doped PS exhibited excellent thermal stability, i.e., the number of dewetting holes was greatly reduced and the long-term hole growth was fairly restricted. In contrast, the neat PS film showed serious surface fluctuation and a final rupture induced by ordinary dewetting. The method developed in this work may pave a road to reinforce thin polymer films and enhance their thermal stability, in order to meet requirements by technological advances.     

Novel synthesis and characterization of CuO nanomaterials:Biological applications

CuO nanoparticles were synthesized at a relatively low temperature(80 ℃) for 2 h using polyethylene glycol-glycerol mixture which acts as a capping agent.A detailed characterization of the synthesized nanomaterials were performed utilizing X-ray diffraction(XRD),infra-red spectroscopy(IR),thermogravimetric analysis(TGA-DTA),transmission electron microscopy(TEM),photoluminescence(PL) by studying its crystalline phase,vibrational mode,thermal analysis,morphology and photoluminescence properties.The effect of annealing on the as-prepared nanoparticles were studied and compared with their corresponding bulk counterpart.The synthesized nanoparticles have been screened for in vitro cytotoxicity(1C_(50)) studies against the human cervical adenocarcinoma cell line(HeLa) using WITT assay methods.The as-prepared nanoparticle inhibits the proliferation of this HeLa cell.The standard disc diffusion method has been used to study the antibacterial activity of the samples against the human pathogenic bacteria Escherichia coli(MTCC 729),Proteus mirabilis(MTCC 425) and Klebsiella pneumoniae subsp.pneumoniae(MTCC 432).The results have been compared with the positive control antibiotic gentamycin.The synthesized nanoparticles would provide a potential alternative to antibiotics for controlling some of the microorganisms causing urolithiasis.     

STUDY ON THE BLENDS OF NYLON 66 AND LIQUID CRYSTALLINE POLYESTERS

Blends of polyamide (Nylon 66) with two different kinds of liquid crystalline polyesters were studied in all the composition range. Homogeneous samples were obtained by coprccipitation from 2 wt%. solution of blends. The thermal properties, crystallinity and morphology of these blends were studied by using DSC, polarizing microscopy, and scanning electron microscopy. The phase transition and morphology of the blends are markedly-influenced by the composition of liquid crystalline polyesters. The mechanical behaviour of PHB/HNA-Nylon 66 blend was improved. although polyamidc (Nylon 66)with the liquid crystalline polyesters were incompatible, but a rather strong interaction between the polymers did exist.     

Exploring the Microstructure of YBCO Nanopowders

High temperature superconductor YBa2Cu3O7-π (YBCO) nanopowders were successfully prepared by a citrate pyrolysis technique. The phase formation and microstructure of the nanopowders were studied. The microstructure analysis shows that the obtained YBCO powders have very fine grains with a size around several tens of nanomaters. The suoerfine morphology reveals that the thermal agglomeration of the particles decreases with decreasing the annealing temperature and shortening the annealing time. In addition, the complete phase formation of YBCO depends upon the annealing temperature and the annealing time as well. So far, these nanopowders have been used to fabricate the melt-textured YBCO bulk materials.     

Preparation and characterization of the crystalline inclusion complexes between cyclodextrins and poly(1,3-dioxolane)

The preparation and characterization of the crystalline inclusion complexes between a polymeric guest, poly(1,3-dioxolane) (PDXL), and small-molecular hosts, cyclodextrins (CDs) are reported. It is observed that the polymer guest can form crystalline inclusion complexes with three kinds of cyclodextrins, which may be attributed to the high oxygen atom density in PDXL chain. The crystalline inclusion complexes were characterized with FTIR , TGA, X-ray diffraction, SEM, 1H NMR and 13C CP/MAS NMR spectroscopes. It was found that the crystalline inclusion complexes have higher temperature stability than the pure CDs. The X-ray powder diffraction patterns of the crystalline inclusion complexes proved that they have columnar structures. 13C CP/MAS NMR spectra of the crystalline inclusion complexes indicate that CDs adopt a more symmetrical conformation in the complexes, while pure CDs assume a less symmetrical conformation in the crystal without a guest inside their cavities. The morphology of the crystal was     

IN SITU OBSERVATION OF MELTING AND CRYSTALLIZATION BEHAVIORS OF POLY(ε-CAPROLACTONE) ULTRA-THIN FILMS BY AFM TECHNIQUE

The melting and crystallization behaviors of poly(ε-caprolactone) (PCL) ultra-thin films with thickness from 15 nm to 8 nm were studied by AFM technique equipped with a hot-stage in real-time. It was found that melting can erase the spherulitic structure for polymer film with high thickness. However, annealing above the melting point can not completely erase the tree-like structure for the thinner polymer film. Generally, the structure formation of thin polymer films of PCL is controlled not only by melting and crystallization but also by dewetting during thermal annealing procedures, and dewetting predominates in the structure formation of ultra-thin films. However, the presence of tree-like morphology at 75 °C may be due to the strong interaction between PCL and mica surface, which may stick the PCL chains onto the mica surface during thermal annealing process. Moreover, the growth of the dendrites was investigated and it was found that crystallization is followed from a dewetted sample, and the branches did not grow with the stems. The crystallization of polymer in the ultra-thin films is a diffusion-controlled process. Both melting and crystallization behaviors of PCL in thin films are influenced by film thickness.     

Effect of Annealing Temperature on Low-temperature Toughness of β-Nucleated Polypropylene Random Copolymer/Ethylene-Propylene-Diene Terpolymer Blends

In this study, the effect of annealing temperature on the impact toughness of β-nucleated polypropylene random copolymer(PPR) and ethylene-propylene-diene terpolymer(EPDM) blends was investigated by differential scanning calorimetry(DSC), wide-angle X-ray diffraction(WAXD), dynamic mechanical analysis(DMA) and scanning electron microscopy(SEM). Interestingly, the impact strength of β-PPR/20 EPDM blend annealed at 120 ℃ is 1.8 times as high as that of unannealed samples. In addition, the crystalline structure, the relaxation of chain segments and fracture morphology of β-PPR/EPDM blends were also investigated to explore the toughening mechanism related to annealing. The results show that annealing at moderate temperatures results in the improvement of integrity of the crystal structure and the relative content of β-phase. The work provides a possible method to toughen the semicrystalline polymer at low temperatures by annealing.     

非晶碳纳米球的低温石墨化(英文)

The investigation by SEM/TEM, porosity, and X-ray diffraction measurements of the graphitization process starting from amorphous carbon nanospheres, prepared by glucose carbonization, is reported. Aspects studied are the annealing temperature in the 750–1000 °C range, the type of inert carrier gas, and time of treatment in the 2–6 h range. It is investigated how these parameters influence the structural and morphological characteristics of the carbon materials obtained as well as their nanostructure. It is shown that it is possible to maintain after graphitization the round-shaped macro morphology, a high surface area and porosity, and especially a large structural disorder in the graphitic layers stacking, with the presence of rather small ordered domains. These are characteristics interesting for various catalytic applications. The key in obtaining these characteristics is the thermal treatment in a flow of N2. It was demonstrated that the use of He rather than N2 does not allow obtaining the same results. The effect is attributed to the presence of traces of oxygen, enough to create the presence of oxygen functional groups on the surface temperatures higher than 750 °C, when graphitization occurs. These oxygen functional groups favor the graphitization process.     

氧化铝和氧化锆催化剂上2-取代苯并咪唑和1,5-二取代苯并二氮的合成(英文)

In this study, alumina, zirconia, manganese oxide/alumina, and manganese oxide/zirconia have been investigated for their catalytic activity in the condensation reaction between o-phenylenediamine and an aldehyde or a ketone to synthesise 2-substituted benzimidazoles and 1,5-disubstituted benzodiazepines respectively. Surface area, surface acidity, and morphology of the catalysts have been analysed and correlated with their catalytic activity. The isolated yields of 2-substituted benzimidazoles and 1,5-disubstituted benzodiazepines are in the range of 30% to 95%. A good correlation between the amount of surface acid sites as well as the surface morphology of the catalysts and the catalytic activity has been observed. This method has been found to be simple and economical. The solid supports could be regenerated and reused without much loss in their activity. Further, the solid supports have been also found to be effective as general catalysts in the condensation of o-phenylenediamine with other substituted aldehydes and ketones.     

Controllable synthesis of well-ordered TiO2 nanotubes in a mixed organic electrolyte for high-efficiency photocatalysis

Well-ordered TiO 2 nanotube arrays (TNAs) were fabricated by electrochemical anodization in a mixed organic electrolyte consisting of ethylene glycol and glycerol. The morphology, structure, crystalline phase, and photocatalytic properties of TNAs were characterized by using TEM, SEM, XRD and photodegradation of methylene blue. It was found that the morphology and structure of TNAs could be significantly influenced by the anodization time and applied voltage. The obtained tube length was found to be proportional to anodization time, and the calculated growth rate of nanotubes was 0.6 m/h. The microstructure analysis demonstrated that the diameter and thickness of the nanotubes increased with the increase of anodization voltage. The growth mechanism of TNAs was also proposed according to the observed relationship between current density and time during anodization. As expected, the obtained TNAs showed a higher photocatalytic activity than the commercial TiO 2 P25 nanoparticles.     

Studies on Blends of Nylon 6 and a Thermotropic Liquid Crystalline Polyarylester(Ⅱ)——Morphology and Rheology

Blends of nylon 6 (PA6) and a semirigid thermotropic liquid crystalline polyarylester (THH) were prepared by coprecipitation. The changing of the morphology of the blends with their compositions was observed by means of a polarizing microscope and scanning electron microscope. The THH phases in the blends changed gradually from spherical droplets to fibrils with the increase of THH content. The flow behavior of the blends are quite different from that of the parent polymers and a very dramatic reduction in the melt viscosity of blends containing 5% THH was observed. The formation possibility of in-situ reinforcement composites of PA6 blends with a semirigid LCP is discussed in the present paper.     

Fe(OH)2悬浮液在EDTA作用下氧气氧化生成δ-FeOOH的机理研究

At room temperature and in the presence of trace EDTA, the formation of δ-FeOOH was studied by the rapid oxidation of Fe(OH)2 suspension with O2. The structural and morphological changes were characterized by various techniques such as XRD, FTIR and TEM. γ-FeOOH and δ-FeOOH formed simutaneously in the early period of oxidation. But as the rate of mass transfer was in equilibrium, trace γ-FeOOH vanished gradually. Accordingly, pure phase δ-FeOOH was obtained. At the same time, critical amount ratio K of EDTA to Fe^2 was verified. The experiments show that the reactivity, rate of the oxidizing agent and pH of the initial medium were important factors for the formation of pure phase δ-FeOOH. Under the auxiliary effect of EDTA, the reactivity of O2 was nearly improved to that of H2O2. And the process of the oxidation that Fe(OH)2 suspension was oxidized by O2 under that condition was discussed.     

Distribution of δD in 25-cm Surface Snow Along Trans-Antarctic Route (Ⅱ)——The “1990 International Trans-Antarctic Expedition” Glaciological Research

On the way of the "1990 International Trans-Antarctic Expedition", the first author of this paper, the Chinese member of the expedition, collected 104 snow samples in 25-cm surface snow along a 5986-km route on Antarctic ice sheet from west to east. The geographical distribution of δD across the Antarctica by the longest route is obtained from stable isotope analysis for the first time. After discussing regional differences of physical geographic conditions, maritime-continental influence, altitudes and latitudes at sampling sites, the distribution of δD is considered to have a close relation to latitudes, but the topographic effect is prominent in some particular regions. The mean annual temperature at sampling site and its relationship with δD in surface snow covering Antarctica from west to east are discussed also. The δD-temperature gradient from the south end of Antarctic Peninsula to Vostok obtained in this paper is very close to that in Terre Adelie Land obtained by predecessors. The snow-dri     

CeO2 Particles Anchored to Ni2P Nanoplate for Efficient Photo-catalytic Hydrogen Evolution

Photocatalytic hydrogen evolution can convert intermittent and dispersive solar energy into hydrogen with high energy density,which is expected to fundamentally solve the problems of environmental pollution and energy shortages.In this experiment,the performance of the catalyst is modified by introducing cocatalyst and morphology control.Ni(OH)2 nanoflowers are used as substrates to derive nanoplate stack Ni₂P by high-temperature phosphating method,and a great many of CeO₂ nanoparticles are anchored in the Ni₂P.This unique 3D/0D combination effectively inhibits the agglomeration of CeO₂ nanoparticles and shortens the electron transfer path.Secondly,the introduction of metal-like performance of Ni₂P broadens the light absorption range of the catalyst and reduces the overpotential of the catalyst,which is a key factor in enhancing the catalytic activity.The design ideas of this experiment have reference significance for the design of efficient and environmentally friendly photocatalysts.     

Glucose-sensitivity of core-shell microspheres and their crystalline colloidal arrays

Thermoresponsive core-shell microspheres are prepared and functionalized with 3-aminophenylboronic acid to make them responsive to glucose.The volume phase transition of the resulting particles is shifted to a lower temperature and a clear swelling is caused by the presence of glucose.The particles after the functionalization preserved their capability to form crystalline colloidal arrays.The changes of their properties may be used in the design of glucose sensors.     

THERMOTROPIC LIQUID CRYSTALLINE COPOLYESTERS-SOLID STATE POLYMORPHISM

This paper offers some new evidence on the polymorphism of solid state of liquid crystalline aromatic copolyesters which were prepared in our laboratory. The effects of different treatment conditions(quenching and annealing) on solid structure have been examined mainly by DSC and X-ray diffraction. The discussion focuses on the supercooled mesophase and low temperature solid-solid transition, the shifting of double melting peaks of annealed samples and the changing of their ΔH data depending on the treatment temperature, time and thermal scanning rate.     

Orientation Efforts as Regulatory Factor of Structure Formation in Permeable Porous Poly(vinylidene fluoride) Films

The manufacturing process of poly(vinylidene fluoride) microporous films containing through flow channels and permeable to liquids has been elaborated. The process is based on polymer melt extrusion with subsequent stages of annealing, uniaxial extensions("cold" and "hot" drawing), and thermal stabilization. The effect of orientation parameters(melt draw ratio and extension degrees) on overall porosity, permeability, morphology, and content of polar piezoactive β-phase in crystalline structure of the films was investigated by filtration porosimetry, sorptometry, scanning electron microscopy, X-ray scattering, and mechanical properties measurements. It is shown that the through pores were formed by a percolation mechanism. It is observed that permeability and the β-phase content increased with the growth of extension degree at the pore formation stages but the portion of β-crystallites decreased with increasing melt draw ratio at extrusion, which permitted to regulate the combination of through permeability and piezoactivity values by variation of the preparation process parameters.