芦丁在铂纳米/碳纳米管修饰电极上电化学行为研究

通过电沉积的方式在多壁碳纳米管(MWCNTs)修饰玻碳电极表面上沉积铂(pt)纳米粒子,并运用循环伏安法(CV)、示差脉冲伏安法(DPV)探讨了芦丁在铂纳米/碳纳米管/玻碳电极上的电化学行为.实验结果表明,芦丁在该修饰电极上呈现一对良好氧化还原峰,其氧化峰电流与浓度在3.2×10(-8)～1.2×10(-5)mol/L...     

萘乙酸在多壁碳纳米管-离子液体复合修饰电极上的电催化氧化及电分析方法

运用循环伏安法(CV),计时库仑法(CC),计时电流法(CA)研究了萘乙酸(NAA)在玻碳电极(GCE),多壁碳纳米管修饰玻碳电极(MWCNTs/GCE)和多壁碳纳米管-离子液体修饰玻碳电极(MWCNTs-IL/GCE)上的电化学行为及电化学动力学性质.实验结果表明,NAA在GCE电极上于1.00V附近有一不可逆氧化峰...     

离子液体中水热合成Pt-Pd/MWCNTs和Pd/MWCNTs催化剂

采用水热合成法, 以离子液体1-乙基-3-甲基咪唑四氟硼酸盐(C₆H₁₁BF₄N₂, EMIBF₄)为溶剂制备了Pt-Pd/MWCNTs(Multi-walled carbon nanotubes)和Pd/MWCNTs催化剂. X射线衍射(XRD)和X射线能量散射谱(EDS)测试证明了Pt-Pd合金和Pd纳米颗粒在MWCNTs的表面生成. 透射电子显微镜(TEM)照片不仅证明了在MWCNTs表面Pt-Pd, Pd纳米颗粒的生成, 而且还表明样品颗粒的平均粒径约为4 nm. 循环伏安(CV)和交流阻抗(EIS)测试表明, 在碱性环境下, 乙醇在Pt-Pd/MWCNTs和Pd/MWCNTs修饰的玻碳(GC)电极上均能发生氧化反应, 与Pd/MWCNTs修饰的电极相比, 在Pt-Pd/MWCNTs上乙醇的起峰电位负移了大约200 mV, 且具有更高的氧化峰电流值.     

基于纳米银/多壁碳纳米管修饰电极的电化学法测定磺胺甲唑

以表面处理多壁碳纳米管(MWCNTs)和硝酸银为原料,利用硼氢化钠还原法制备了纳米银/多壁碳纳米管复合材料(AgNPs/MWCNTs),并通过紫外-可见吸收光谱、红外光谱、拉曼光谱和X射线衍射进行表征。采用滴涂法将该纳米复合材料修饰至玻碳电极表面,得到纳米银/多壁碳纳米管修饰电极(AgNPs/MWCNTs/GCE)。以AgNPs/MWCNTs/GCE为工作电极,研究了缓冲溶液、pH值、支持电解质和扫描速度对磺胺甲■唑(SMZ)电化学反应活性的影响。结果表明,与多壁碳纳米管、纳米银单独修饰电极相比,该纳米复合材料修饰电极对SMZ显示了更高的电催化活性。优化条件下,SMZ浓度在3.0×10~(-7)～5.0×10~(-5) mol/L范围内与峰电流呈线性关系,检出限(S/N=3)为6.4×10~(-8) mol/L。该方法操作简单、快速,可用于河水样品中SMZ的检测。     

聚(3-氨基-5-巯基-1,2,4-三唑)/多壁碳纳米管修饰的玻碳电极同时检测尿酸、黄嘌呤与次黄嘌呤

采用滴涂法得到多壁碳纳米管(MWCNTs)修饰的玻碳电极(GCE),通过电沉积方法将3-氨基-5-巯基-1,2,4-三唑(TA)沉积在MWCNTs/GCE表面,制备了聚(3-氨基-5-巯基-1,2,4-三唑)/多壁碳纳米管修饰电极(p TA/MWCNTs/GCE)。采用循环伏安法(CV)和示差脉冲伏安法(DPV),研究了尿酸(UA)、黄嘌呤(XA)和次黄嘌呤(HX)在该修饰电极上的电化学行为。结果表明,该修饰电极对UA、XA和HX均有较好的电催化活性作用,能实现对3种物质的同时测定。UA、XA和HX在该修饰电极上的线性范围分别为9.0~739.0、2.0~259.0、1.0~353.0μmol/L;检出限分别为0.67、0.17、0.33μmol/L。该修饰电极已成功用于尿液和血清实际样品中UA、XA和HX的同时测定,回收率为98.8%~105.5%。     

对乙酰氨基酚在石墨烯/壳聚糖复合膜修饰电极上的电化学行为研究

制备了石墨烯-壳聚糖复合物修饰玻碳电极(GO/CS-GCE),考察了对乙酰氨基酚(APAP)在修饰电极上的电化学行为,发现石墨烯-壳聚糖复合物能较好改善玻碳电极对APAP的电化学性能,APAP在修饰电极上的电化学反应过程是受吸附控制的2电子,2质子反应过程;进一步研究发现在pH=9.16的碳酸钠-碳酸氢钠缓冲体系中,对...     

基于掺杂碳纳米管的复合体系电化学生物传感器研究

制备了含有铂纳米颗粒(NSPt)的壳聚糖(CHIT)和正硅酸四乙酯(TEOS)溶胶-凝胶溶液,将多壁碳纳米管(MWCNTs)分散于制备的CHIT和TEOS溶胶-凝胶混合物体系,并用高倍透射电镜(TEM)和扫描电子显微镜(SEM)对NSPt-CHIT表面和MWCNTs进行了表征。此种复合膜修饰玻碳电极对过氧化氢有灵敏的电化学响应。通过在此复合膜修饰的玻碳电极上固定葡萄糖氧化酶(GOx)制备了葡萄糖生物传感器。该传感器对葡萄糖在0.05~8 mmol/L范围有线性响应,相关系数为0.996,检出限(S/N=3)为10μmol/L。传感器对葡萄糖有灵敏响应,并有很好的重现性和稳定性,应用于实际样品体系的回收试验,结果良好。     

磁性纳米微球-血红蛋白修饰电极的电化学行为及对H2O2电催化还原的研究

将天然高分子壳聚糖(CS)包裹碳包铁的磁性纳米微球(CFN/CS)修饰于玻碳电极表面,并利用戊二醛将血红蛋白(Hb)交联在CFN/CS上,制备了Hb-CFN/CS-GC电极。循环伏安法和电化学交流阻抗法实验结果表明,Hb在CFN/CS-GC电极表面仍保持较好的生物活性,能稳定有效地进行直接电子转移反应。电化学研究表明该修饰电极对H2O2有良好的电催化还原作用,在pH 7.0的磷酸盐(PBS)介质中,H2O2在5.2×10-5~2.3×10-3mol/L浓度范围内,其浓度与还原峰电流呈良好线性关系,检出限为8.7×10-6mol/L。该修饰电极有着良好的重现性和稳定性。     

壳聚糖/多壁碳纳米管复合膜电化学手性识别色氨酸对映异构体

采用滴涂方式将羧酸化多壁碳纳米管(f-MWCNTs)修饰于玻碳电极(GCE)表面成膜,然后恒电位法在上述修饰电极表面电沉积壳聚糖(CS)膜,形成CS和f-MWCNTs复合膜修饰电极(CS/f-MWCNTs/GCE),并用于色氨酸(Trp)对映异构体的手性识别。采用扫描电子显微镜(SEM)表征了修饰电极表面形貌的差异,电化学阻抗(EIS)和循环伏安法(CV)研究修饰电极的电化学行为差异。差分脉冲伏安法(DPV)用于区别色氨酸(Trp)对映异构体,分离系数可达2.38。研究发现该修饰电极对L-Trp的DPV响应信号强于D-Trp,检测的线性范围为8.0×10~(-6)~4.0×10~(-3)mol/L,检出限(S/N=3)为5.0×10~(-6)mol/L。该方法简单、经济、快速,对发展其它手性化合物的检测方法提供了参考。     

基于CdSe@CdS/壳聚糖/gC3N4复合物的卡那霉素电化学发光适配体传感器

利用核壳型的CdSe@CdS量子点作为发光物质,并用壳聚糖(CS)、类石墨烯氮化碳(gC₃N₄)与CdSe@CdS量子点合成了CdSe@CdS/CS/gC₃N₄复合物,将该复合物修饰至玻碳电极(GCE)表面,将适配体(Apt)的互补DNA链(cDNA)通过化学反应连接到量子点上,Apt与cDNA发生杂交反应而被修饰至电极表面。将辣根过氧化物酶(HRP)固定到该修饰电极表面,构建了检测卡那霉素(Kana)的电化学发光(ECL)适配体传感器。通过生物催化沉淀(BCP)方法实现Kana的检测,溶液中无Kana时,在H₂O₂的存在下,修饰在电极上的HRP可以催化氧化4-氯-1-萘酚(4-CN),在电极表面产生不导电的苯并-4-氯己二烯酮沉淀,导致电化学发光信号明显降低。溶液中存在Kana时,Kana会与Apt特异性结合,部分dsDNA解旋,导致部分HRP从电极表面脱落,BCP反应减弱,导致ECL信号增强,实现目标物质的特异性检测。计算适配体传感器在Kana溶液中的...     

磷酸铁锂离子电池正极材料掺碳纳米管的研究

应用球磨法于LiFePO4掺杂多壁碳纳米管,制成LiFePO4/MWCNTs复合电极,然后以其组装成锂离子电池.研究不同比例掺杂多壁碳纳米管对复合材料电极电化学性能的影响.XRD、SEM表征及电化学性能测试表明,多壁碳纳米管含量为10%(bymass)的LiFePO4/MWCNTs电极比其它比例的复合电极具有更优良的充放电性能,而且极化小、稳定性强、充放电平台更平稳,导电率更高.在常温0.1C下充放电,首次充、放电比容量分别为139和128.5mAh.g-1,库仑效率达92.4%,循环40次后,电极比容量损失率仅为5.3%.     

镧掺杂的二氧化锰/碳纳米管电化学超级电容器复合电极

尽管在二氧化锰/多壁碳纳米管（MnO₂/MWCNTs）上获得了较高的比电容,低电导率仍是制约MnO₂担载量或膜厚度提高的主要障碍.另一个问题是MnO₂/MWCNTs的循环稳定性远低于活性炭.所以截止到目前这一新型材料的应用仍然受到很大的限制.本文采用原位还原的方法制备镧掺杂二氧化锰/多壁碳纳米管电化学超级电容器复合电极材料.分别通过透射电镜（TEM）、扫描电镜（SEM）、X射线衍射（XRD）和傅里叶变换红外（FTIR）光谱等技术对这些复合材料的形貌与结构进行了分析.采用循环伏安法、恒电流充放电法和交流阻抗法对其进行了电化学性能的研究.研究结果表明,通过还原MnO₄^-可以在MWCNTs上形成La掺杂MnO₂复合材料.La掺杂降低了复合电极的电阻,这是因为La的引入可以增大MnO₂的晶格缺陷,从而提高材料的电导率以及电极的电化学性能.因此La掺杂是克服MnO₂本征导电性差的有效途径之一.掺杂La可以在不增大电极电阻的情况下提高MnO₂的担载量或膜厚度.La掺杂的更重要的作用是使以MnO₂/MWCNTs作电极的对称电化学超级电容器的循环性能得到显著改善.此外,La掺杂也使复合电极的比电容得到一定程度的提高.     

Highly Selective and Sensitive Detection of Dopamine in the Presence of Excessive Ascorbic Acid Using Electrodes Modified with C60‐Functionalized Multiwalled Carbon Nanotube Films

Electrochemical detection of dopamine (DA) in the presence of a large excess of ascorbic acid (AA) was investigated with a novel all‐carbon nanocomposite film of C₆₀‐MWCNTs (C₆₀‐functionalized multi‐walled carbon nanotubes) using a bare MWCNTs film as control. Although both films can selectively detect DA from AA by separating their oxidation potentials, the C₆₀‐MWCNTs film shows special selectivity and good sensitivity for detecting DA. On one hand, the C₆₀‐MWCNTs composite film shows a higher activity for DA oxidation with enhanced peak current. On the other hand, the C₆₀‐MWCNTs composite film effectively suppresses the oxidation of AA. Remarkably, it is found that the oxidation current of DA is over 2 times higher than that of AA even when the concentration of AA is about 3 to 4 orders of magnitude higher than that of DA. This offers a tremendous advantage for the simple and clean detection of DA free of the interfering AA signal in a real assay. Cyclic voltammetry, differential pulse voltammetry, and electrochemical impedance spectrometry are used to characterize the C₆₀‐MWCNTs composite film. These novel properties are interpreted to arise from the facile electron transfer between C₆₀ and MWCNTs in the C₆₀‐MWCNTs nanocomposite film.     

Fabrication of highly sensitive and selective nanocomposite film based on CuNPs/fullerene-C60/MWCNTs: An electrochemical nanosensor for trace recognition of paracetamol

Designing an electrochemical sensor for versatile clinical applications is a sophisticated task and how dedicatedly functionalized composite materials can perform on this stage is a challenge for today and tomorrow's Nanoscience and Nanotechnology. In the present work, we demonstrate a new strategy for the development of novel electrochemical sensor based on catalytic nanocomposite film. Fullerene-C₆₀ and multi-walled carbon nanotubes (MWCNTs) were dropped on the pre-treated carbon paste electrode (CPE) and copper nanoparticles (CuNPs) electrochemically deposited on the modified CPE to form nanocomposite film of CuNPs/C₆₀/MWCNTs/CPE. In this work, an electrochemical method based on square wave voltammetry (SWV) employing CuNPs/C₆₀/MWCNTs/CPE has been presented for the recognition and determination of paracetamol (PT). Developed electrochemical sensor was characterized using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronocoulometry. The composite film made the fabricated sensor to display high sensitivity and good selectivity for PT detection. The influence of the optimization parameters such as pH, accumulation time, deposition potential, scan rate and effect of loading of composite mixture of C₆₀-MWCNTs and CuNPs on the electrochemical performance of the sensor were evaluated. A linear range from 4.0 × 10⁻⁹ to 4.0 × 10⁻⁷ M for PT detection was obtained with a detection limit of 7.3 × 10⁻¹¹ M. The fabricated sensor was successfully applied to the detection of PT in biological samples with good recovery ranging from 99.21 to 103%.     

Ultrasensitive Voltammetric Detection of Trace Lead(II) and Cadmium(II) Using MWCNTs‐Nafion/Bismuth Composite Electrodes

Multiwall carbon nanotubes were dispersed in Nafion (MWCNTs‐NA) solution and used in combination with bismuth (MWCNTs‐NA/Bi) for fabricating composite sensors to determine trace Pb(II) and Cd(II) by differential pulse anodic stripping voltammetry (DPASV). The electrochemical properties of the MWCNTs‐NA/Bi composites film modified glassy carbon electrode (GCE) were evaluated. The synergistic effect of MWCNTs and bismuth composite film was obtained for Pb(II) and Cd(II) detection with improved sensitivity and reproducibility. Linear calibration curves ranged from 0.05 to 100 μg/L for Pb(II) and 0.08 to 100 μg/L for Cd(II). The determination limits (S/N=3) were 25 ng/L for Pb and 40 ng/L for Cd, which compared favorably with previously reported methods in the area of electrochemical Pb(II) and Cd(II) detection. The MWCNTs‐NA/Bi composite film electrodes were successfully applied to determine Pb(II) and Cd(II) in real sample, and the results of the present method agreed well with those of atomic absorption spectroscopy.     

三元复合材料PANI／Ag／MWNT的电化学行为和比电容

通过原位聚合的方式在银纳米粒子/多壁碳纳米管（Ag/MWCNT）复合材料的表面成功聚合苯胺单体制备了聚苯胺/银纳米粒子/多壁碳纳米管（PANI/Ag/MWCNT）三元复合材料苯．通过对三元复合材料的结构以及表面形貌进行分析,表明聚苯胺层完全包覆了Ag/MWCNT复合材料,形成了核壳式结构．同时银纳米粒子则以单质晶体的形态存在于多壁碳纳米管与聚苯胺层之间．三元复合材料电极在1 mol/L的KOH溶液中具有极低的阻抗,而与聚苯胺电极相比,这些复合材料电极则表现出更低的电阻、更高的电化学活性和更好的循环稳定性．尤其是当苯胺和Ag：MWCNTs质量比为5：5时,该复合材料电极在0.25 A/g的电流密度下表现出最大的比电容值为160 F/g．     

Efficient Direct‐Methanol Fuel Cell Based on Graphene Quantum Dots/Multi‐walled Carbon Nanotubes Composite

Direct‐methanol fuel cells are proton‐exchange fuel cell in which methanol is used as the fuel. The important advantage of these fuel cells is the simplicity of transport and storage of methanol. In this study, methanol fuel cell electrocatalysts including graphene quantum dots (GQDs), functionalized multi‐walled carbon nanotubes (f‐MWCNTs) and GQDs/f‐MWCNTs composite were synthesized. The structures of synthesized electrocatalysts were highlighted by scanning electron microscope (SEM), raman spectroscopy, UV–vis spectroscopy, fourier transform infrared spectroscopy (FTIR), electrochemical impedance spectroscopy (EIS) and x‐ray diffraction (XRD) method. After that, the effective surface areas (ESA) of GQDs, f‐MWCNTs and GQDs/f‐MWCNTs were calculated. Finally, GQDs/f‐MWCNTs composite modified glassy carbon electrode (GQDs/f‐MWCNTs/GCE) showed highest current signals for methanol oxidation than those of comparable GQDs/GCE and f‐MWCNTs/GCE.     

聚合酞菁铁/多壁碳纳米管复合材料的制备及氧还原催化性能

采用高效、 便捷的微波合成法制备了4种不同结构的聚合酞菁铁/多壁碳纳米管(Poly-FePc/MWCNTs)复合材料并进行了表征. 结果表明, 聚合酞菁铁均匀地包裹在多壁碳纳米管上. 利用线性扫描电位法(LSV)和电化学阻抗法(EIS)对材料的氧还原催化活性进行了研究, 发现FePPc/MWCNTs复合材料具有最好的氧还原催化活性. 采用X射线光电子能谱(XPS)和X射线吸收精细结构光谱(XAFS)研究了Poly-FePc/MWCNTs复合材料中酞菁铁结构变化与氧还原催化性能的相关性. 结果表明, FePPc/MWCNTs复合材料中Fe-N₄接近平面结构, 聚合酞菁铁能够更好地与MWCNTs产生协同作用, 从而加速氧还原过程中电子的转移, 提高氧还原活性.     

Insights into MWCNTs/polyimide nanocomposites: from synthesis to application as free-standing flexible electrodes in low-cost micro-supercapacitors

In the pursuit to enlarge the library of polyimide materials for energy applications, new polyimide/MWCNTs composite films have been developed by MWCNTs-assisted polycondensation reaction of a hydroxyl and triphenylmethane-containing diamine with benzophenone tetracarboxylic dianhydride targeting to highlight their electrical storage capability as flexible electrodes in micro-supercapacitors (mSCs). The Fourier-transform infrared spectroscopy, proton nuclear magnetic resonance, UV–vis, fluorescence, and Raman spectroscopies were used to demonstrate the evolution of interfacial interactions between MWCNTs and the precursors (diamine monomer and intermediate polyamidic acid) and polyimide matrix that proved to be the origin of MWCNTs homogeneous dispersion. Thus, composite films incorporating 1, 3, 5, and 10 w.t.% MWCNTs were obtained and thoroughly investigated with regard to their morphology, mechanical behavior, thermal stability, and electrical conductivity. The electrochemical performance of these composites was first analyzed in a classical three-electrode cell by cyclic voltammetry and galvanostatic charge-discharge in both aqueous and organic electrolyte systems. By far, the best electrical storage capacity was obtained with the composite polyimide film containing 10% MWCNTs that was further used as both active material and current collector in a flexible symmetric mSC realized by a straightforward and low-cost procedure. In the attempt to better exploit the advantages of this composite film, it was layered with a graphite-containing paint and tested as an electrode in a flexible mSC, which provided satisfactory results. To our knowledge, this is the first report on the electrical charge storage capability of a polyimide/MWCNTs free-standing film as a flexible electrode in mSCs, which do not require time- and resource-consuming processing steps.     

氢氧化镍/多壁碳纳米管复合材料的溶剂热法制备及电容性能

采用溶剂热法制备了氢氧化镍/多壁碳纳米管[Ni(OH)2/MWCNTs]复合纳米材料;借助X射线衍射仪和透射电镜分析了产物的结构和形貌,利用循环伏安测试测定了复合材料的电容特性.结果表明:片状β-Ni(OH)2较好地附着在MWCNTs上;复合样品的循环伏安行为明显有别于空白样品Ni(OH)2,峰电流较高.这表明引入MWCNTs可改善Ni(OH)2的电化学性能.与此同时,当MWCNTs的质量分数为10%时,相应的Ni(OH)2/MWCNTs复合物的氧化还原峰电位差最小,循环可逆性最佳.