Fe2BiTaO7纳米催化剂的组织结构及光催化性能

用固相反应合成法合成了光催化剂Fe₂BiTaO₇,通过XRD、SEM、TEM、紫外-可见漫反射等表征方法对其组织结构及光催化性能进行了研究.结果表明Fe₂BiTaO₇为立方晶系烧绿石结构,空间群为Fd₃m,禁带宽度为1.72eV.通过比较Fe₂BiTaO₇、P₂₅TiO₂、掺氮TiO₂和Bi₂InTaO₇的可见光光催化降解罗丹明B,发现Fe₂BiTaO₇降解效果及催化活性均高于其它催化剂,并且Fe₂BiTaO₇降解罗丹明B效率是掺氮二氧化钛的1.5倍.Fe₂BiTaO₇降解罗丹明B的曲线符合一级动力学,一级动力学常数为0.02293 min^-1.研究了罗丹明B可能的降解路径和Fe₂BiTaO₇在可见光下降解苯酚的效果.Fe₂BiTaO₇(可见光)光催化剂系统适用于纺织工业废水处理.     

Fe2BiTaO7纳米催化剂的组织结构及光催化性能

用固相反应合成法合成了光催化剂Fe2BiTaO7,通过XRD、SEM、TEM、紫外-可见漫反射等表征方法对其组织结构及光催化性能进行了研究。结果表明Fe2BiTaO7为立方晶系烧绿石结构,空间群为Fd3m,禁带宽度为1.72 e V。通过比较Fe2BiTaO7、P25TiO2、掺氮Ti O2和Bi2In Ta O7的可见光光催化降解罗丹明B,发现Fe2BiTaO7降解效果及催化活性均高于其它催化剂,并且Fe2BiTaO7降解罗丹明B效率是掺氮二氧化钛的1.5倍。Fe2BiTaO7降解罗丹明B的曲线符合一级动力学,一级动力学常数为0.022 93 min-1。研究了罗丹明B可能的降解路径和Fe2BiTaO7在可见光下降解苯酚的效果。Fe2BiTaO7(可见光)光催化剂系统适用于纺织工业废水处理。     

Structural characterization and photocatalytic properties of novel Bi<Subscript>2</Subscript>FeVO<Subscript>7</Subscript>

Bi₂FeVO₇ was prepared by a solid-state reaction technique for the first time and the structural and photocatalytic properties of Bi₂FeVO₇ were studied. The results shows that this compound crystallized in the tetragonal crystal system with space group I4/mmm. Moreover, the band gap of Bi₂FeVO₇ was estimated to be about 2.22(6) eV. For the photocatalytic water splitting reaction, H₂ or O₂ evolution was observed from pure water with Bi₂FeVO₇ as the photocatalyst by ultraviolet light irradiation. Degradation of aqueous methylene blue (MB) dye by photocatalytic way over this compound was further studied under visible light irradiation. Bi₂FeVO₇ shows higher catalytic activity compared to TiO₂ (P-25) for MB photocatalytic degradation under visible light irradiation. Complete removal of aqueous MB was realized after visible light irradiation for 170 min with Bi₂FeVO₇ as the photocatalyst. The reduction of the total organic carbon (TOC) and the formation of inorganic products, SO ₄ ²⁻ and NO ₃ ⁻ revealed the continuous mineralization of aqueous MB during the photocatalytic course.     

Preparation and characterization of ZnTiO<Subscript>3</Subscript>–TiO<Subscript>2</Subscript>/pillared montmorillonite composite catalyst for enhanced photocatalytic activity

ZnTiO₃–TiO₂/organic pillared montmorillonite (pMt) composite catalyst was successfully prepared in this paper by immobilizing ZnTiO₃–TiO₂ onto pMt. The composition and texture of the prepared composite catalyst were characterized by X-ray diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, transmission electron microscopy, energy dispersive spectrometry, ultraviolet–visible light (UV–Vis) diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy. The photocatalytic activity was tested via photocatalytic degradation of methyl blue (MB) under both visible irradiation and UV light. The results indicated that the ZnTiO₃–TiO₂/pMt composite catalyst had an apparent absorption at the area of visible irradiation, and exhibited a higher efficiency of photocatalytic degredation of MB under visible irradiation. This was due to the heterostructure of ZnTiO₃–TiO₂, and the mesoporous structure and specific surface area of the ZnTiO₃–TiO₂/pMt composite. In addition, the results of the radical scavenging experiments showed that the holes and superoxide radicals are responsible for the degradation of MB under visible irradiation.     

Facile ion-exchange synthesis of Gd-doped K2Ta2O6 photocatalysts with enhanced visible light activity

One of the well-known ways of increasing the visible light absorption capability of semiconducting materials is cation doping. This study aims to use Gd doping to tailor the bandgap energy of K₂Ta₂O₆ (KTO) for photocatalytic degradation of organic pollutants under visible light irradiation. Accordingly, the parent KTO and Gd-doped KTO with different Gd concentrations (K_2-3xGd_xTa₂O₆; x = 0.025, 0.05, 0.075 and 0.1 mol%) were synthesized by hydrothermal and facile ion-exchange methods, respectively. The powder XRD, FT-IR, SEM-EDS, TEM-SAED, N₂ adsorption-desorption, XPS, UV–Vis DRS, PL and ESR techniques were used to investigate the effect of Gd dopant concentration on the structural and photocatalytic properties of KTO. The photocatalytic activity of these samples was investigated for the photocatalytic degradation of methylene blue (MB) dye in an aqueous solution at room temperature under visible light irradiation. The experimental results show that all Gd-doped KTO samples exhibit enhanced photocatalytic activity compared with parent KTO toward MB degradation. In particular, Gd-KTO obtained by doping of 0.075 mol% shows the highest photocatalytic activity among the Gd-doped samples and the degradation efficiency of MB was 79% after 180 min of visible light irradiation, which is approximately 1.5 times as high as that by parent KTO (53%). In addition, trapping experiments and electron spin resonance (ESR) analysis demonstrated that the hydroxyl radicals (^?OH) have played a crucial role in the photocatalytic degradation of MB. The reusability and stability of Gd doped-KTO with a Gd content of 0.075 mol% against MB degradation were examined for five cycles. Based on the present study results, a visible light induced photocatalytic mechanism has been proposed for Gd0075-KTO sample.     

Adsorption factor and photocatalytic degradation of dye-constituent aromatics on the surface of TiO2 in the presence of phosphate anions

The photocatalytic degradation for some kinds of dye-constituent aromatics with TiO₂ in the presence of phosphate anions in aqueous dispersion was investigated under both visible light (λ>480 nm) and UV irradiation. The influences of phosphate anion upon the degradation of organics under these different conditions was revealed by the measurement of point of zero ξ-potential (P _ZC) of TiO₂, UV-VIS spectra, HPLC and LC-MS. The adsorption and photodegradation of some organics, which adsorb on the surface of TiO₂ by a dominating group bearing a positive charge, was enhanced, while that of others, which adsorb on the surface of TiO₂ by a dominating group bearing negative charge, was depressed by the presence of phosphate anions under UV irradiation at the experimental conditions (pH 4.3). It was confirmed that better adsorption of organics on the surface of TiO₂ had an advantage in their photocatalytic degradation under UV irradiation. On the other hand, although the adsorption of rhodamine B (RhB) and methylene Blue (MB) markedly increased, their degradation under visible light irradiation was depressed in the presence of phosphate anions. It is suggested that phosphate anion greatly blocked the electron transfer from excited RhB and MB molecules as RhB and MB molecules predominantly adsorbed on the surface of TiO₂ through the electrostatic interaction with surface adsorbed phosphate anions.     

Preparation and Photocatalytic Activity of Mesoporous TiO2 Photocatalyst Co‐doped with Fe and H3PW12O40

The mesoporous titanium dioxide (MTiO₂) photocatalysts co‐doped with Fe and H₃PW₁₂O₄₀ were synthesized by template method using tetrabutyl titanate (Ti(OC₄H₉)₄), Fe(NO₃)k₃9H₂Oand H₃PW₁₂O₄₀ as precursors and Pluronic P123 as template. The as‐prepared photocatalyst was characterized by N₂ adsorption‐desorption measurements, X‐ray diffraction (XRD), scanning electron microscopy (SEM) and UV‐vis adsorption spectroscopy, and the photocatalytic activities of the prepared samples under UV and visible light were estimated by measuring the degradation rate of methyl blue (MB) (50 mg/L) in an aqueous solution. The characterizations indicated that the photocatalysts possessed a homogeneous pore diameter of ca. 10 nm with high surface area of ca. 150 m²/g. The results of MB photodecomposition showed that co‐doped mesoporous TiO₂ exhibited higher photocatalytic activities than un‐doped, single‐doped mesoporous TiO₂ under UV and visible light irradiation. It was shown that the co‐doped MTiO₂ could be activated by visible light and could thus be used as an effective catalyst in photo‐oxidation reactions. The synergistic effect of Fe and H₃PW₁₂O₄₀ co‐doping played an important role in improving the photocatalytic activity.     

Efficient Decomposition of Organic Pollutants Over In2O3/TiO2 Nanocomposite Photocatalyst Under Visible Light Irradiation

The heterojunction structures of In₂O₃/TiO₂, exhibiting visible light photocatalytic efficiency, has been synthesized by utilizing maleic acid as an organic linker to combine In₂O₃ and Degussa P25 (TiO₂) nanoparticles. The prepared nanocomposite has been characterized by FESEM, TEM, XRD and UV?CVisible reflectance spectra. The photocatalytic efficiency of the composite photocatalyst has been investigated based on the decomposition of 2-propanol (IP) in gas phase and 1,4-dichlorobenzene (DCB) in aqueous phase under visible light (??????420?nm) irradiation. The results reveal that the In₂O₃/TiO₂ composite photocatalyst with 7?wt% In₂O₃ demonstrated 6.3 times of efficiency in evolving CO₂ from gaseous IP and 8.7 times of efficiency in removing aqueous DCB in compare with Degussa P25. In this In₂O₃/TiO₂ composite system, TiO₂ seems to be the principal photocatalyst whereas the function of In₂O₃ is to sensitize TiO₂ by absorbing visible light (??????420?nm). The extraordinary high photocatalytic efficiency of this composite In₂O₃/TiO₂ under visible light has been explained on the basis of relative energy band positions of the component semiconductors.     

Excellent degradation performance of azo dye by metallic glass/titanium dioxide composite powders

The metallic glass/titanium dioxide powders (MG/TiO₂) with enhanced photocatalytic oxidation activity were synthesized, which exhibit a higher efficiency in decolorizing methylene blue solutions (MB). Compared with the pure TiO₂ and crystalline alloy/TiO₂ (CA/TiO₂) under the same circumstances, its degradation rate was 60 % and 30 % higher, respectively. Furthermore, compared with the CA/TiO₂, the MG/TiO₂ photocatalytic rate was three times faster when decolorizing MB. Considering the excellent intrinsic high-performance photocatalytic degradation under visible light irradiation, these novel powders were proven to have potential applications in water purification industry.     

Characterization, activity and mechanisms of a visible light driven photocatalyst: Manganese and iron co-modified TiO2 nanoparticles

An attempt was made to prepare Mn,Fe-codoped nanostructured TiO₂ photocatalyst for visible light assisted degradation of an azo dye (methylene blue) in aqueous solutions by a sol-gel process. The asprepared nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS) and photoluminescence spectra (PL) techniques. The photocatalytic activity of Mn,Fe-codoped TiO₂ catalyst was evaluated by measuring degradation rates of methylene blue (MB) under visible light. The results showed that doping with the manganese and iron ions significantly enhanced the photocatalytic activity for MB degradation under visible light irradiation. This was ascribed to the fact that a small amount of manganese and iron dopants simultaneously increased MB adsorption capacity and separation efficiency of electron-hole pairs. The results of DRS showed that Mn,Fe-codoped TiO₂ had significant absorption between 400 and 500 nm, which increased with the increase of manganese ion content. It is found that the stronger the PL intensity, the higher the photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions, so that the recombination of photoinduced electrons and holes could be effectively inhibited.     

Photocatalytic intercalated material based on HLaNb<Subscript>2</Subscript>O<Subscript>7</Subscript> as host and Cd<Subscript>0.8</Subscript>Zn<Subscript>0.2</Subscript>S as guest

A novel photocatalytic material (Pt,Cd0.8Zn0.2S)/HLaNb2O7 was fabricated by successive intercalation and exchange reactions. The (Pt,Cd0.8Zn0.2S)/HLaNb2O7 possessed a gallery height less than 0.5 nm and showed a broad absorption with wavelength over 370-500 nm. Using (Pt,Cd0.8Zn0.2S)/HLaNb2O7 as catalyst, the photocatalytic H2 evolution was more than 160 cm3·h-1·g-1 in the presence of Na2S as a sacrificial agent under irradiation with wavelength more than 290 nm from a 100-W mercury lamp. Furthermore, the catalyst showed photocatalytic activity even under visible light irradiation.     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

A Hierarchical Nanostructured Carbon Nanofiber–In2S3 Photocatalyst with High Photodegradation and Disinfection Abilities Under Visible Light

Photocatalytic degradation of pollutants under visible light provides a new door to solve the water contamination problem by utilizing free and renewable sunlight. The search for highly efficient photocatalysts with hierarchical nanostructures remains crucial for accessing this new door. In this work, a new hierarchical nanostructured photocatalyst is designed and synthesized, for the first time, by anchoring In₂S₃ flower‐like nanostructures on non‐woven carbon nanofiber (CNF). The nanostructures of these CNF–In₂S₃ composites were fine‐tuned, with the aim of achieving the highest photocatalytic activity under visible light. The formation mechanism of the hierarchical nanostructure is also investigated. The results indicate that the optimized hierarchical CNF–In₂S₃ photocatalyst is superior in photodegradation and disinfection efficiency to that of pure In₂S₃ under visible‐light irradiation. The prominent photocatalytic activities of these hierarchical CNF–In₂S₃ photocatalysts can be attributed to the excellent properties of enhanced light absorption, large surface area, and efficient charge separation, which are all derived from the special three‐dimensional hierarchical nanostructures. Therefore, this work presents the great potential of this hierarchical nanostructured CNF–In₂S₃ photocatalyst in practical environmental remediation fields.     

Nitrogen‐doped graphene‐cerium oxide (NG‐CeO2) photocatalyst for the photodegradation of methylene blue in waste water

This study shows a facile approach for the preparation of CeO₂ nanoparticles decorated with porous nitrogen‐doped graphene (NG) nanosheets for effective photocatalytic degradation of methylene blue (MB). NG nanosheets were first synthesized using a hydrothermal method and then nitrogen‐doped graphene‐cerium oxide (NG‐CeO₂) was prepared through mixing of cerium nitrate with different concentrations of NG under ultrasonication followed by hydrothermal treatment. The synthesized nanocomposites were characterized using X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and field emission scanning electron microscopy (FE‐SEM). The photocatalytic activity of the synthesized nanocomposites was analyzed against MB dye. Results showed that the nanocomposites of NG‐CeO₂ have an average particle size of 20 nm. The as‐prepared NG‐CeO₂ nanocomposites exhibited outstanding photocatalytic activity for dye degradation under visible light irradiation, which could be attributed to synergistic effects between the NG nanosheets and CeO₂. The quantum of photodegradation increases with the increase of the NG content in the nanocomposites.     

Enhanced photocatalytic activity of Ni doped TiO2 nanowire–nanoparticle hetero–structured films prepared by hydrothermal and sol–gel methods

TiO₂ nanowire-nanoparticle hetero-structured films were prepared via a sol–gel method and coated on glass substrates by dipping method for photocatalytic activity. In this study 0, 1, 3, and 5 mol% of Ni doped were studied. One-dimensional TiO₂ nanowires (NWs) were prepared by hydrothermal treatment with TiO₂ nanoparticles (NPs) which are commercially available. XRD, FESEM, DRS, and XPS were used to characterize the prepared nanowire-nanoparticle hetero-structures films. 3%Ni doped TiO₂ hetero-structured film (TNi3) had the highest photocatalytic activity on the degradation of methylene blue (MB). TNi3 films provided about 4.3 times of degradation rate compared to undoped TiO₂ (T). It revealed that TNi3 film resulted in shifting the absorption wavelength towards narrowing the energy band gap and small crystallite size. Therefore, the TNi3 film exhibited a photocatalytic activity on the degradation of MB under visible light irradiation greater than undoped film.     

A facile preparation and visible light-induced photocatalysis of indium sulfide superstructure

β-In₂S₃ superstructure comprised of nanoflakes with the sizes of 200–450 nm has been synthesized by a facile reflux method with the assistance of the sodium dodecylsulfate at low temperature (80 °C). XRD, SEM, TEM, HRTEM, and UV–vis spectra were used to characterize the In₂S₃ superstructure. Prepared In₂S₃ superstructures exhibited high photocatalytic activities in the degradation of rhodamine B under visible light irradiation (λ > 420 nm), in which 97.5% RhB was photodegraded after 60 min.     

原位碳、氮共掺杂二氧化钛空心球的制备与可见光光催化性能

在H₂O₂-HF 的乙醇-水混合溶液中, 通过水热处理碳氮化钛(TiCN)制备了碳、氮共掺杂TiO₂ 空心球(CNTH). 用X 射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、X 射线光电子能谱(XPS)和紫外-可见(UV-Vis)吸收光谱表征了所制备的样品. 在可见光(λ≥400 nm)照射下, 通过降解甲基蓝检测了碳、氮共掺杂TiO₂空心球的光催化活性. 结果表明, 源于TiCN中的部分碳和氮原子原位掺入了TiO₂的晶格中, 部分碳掺入TiO₂点阵的间隙中. 该材料在整个可见光区展示了增强的可见光吸收, 其带边明显红移. 光催化研究表明在强可见光吸收和独特的空心球结构的协同作用下, 碳、氮共掺杂TiO₂空心球展示了比P25更高的可见光光催化活性.     

光催化剂Sm2FeSbO7的制备及光物理和光催化性能表征

首次采用固相反应法制备了新型光催化剂Sm₂FeSbO₇,有效地降解了水中有机污染物。利用X射线衍射、扫描电镜、X射线光电子能谱、傅里叶变换红外光谱、透射电子显微镜和紫外－可见光谱仪对Sm₂FeSbO₇的结构和光催化性能进行了表征。Sm₂FeSbO₇为烧绿石型结构,立方晶系和空间群Fd3m结晶。Sm₂FeSbO₇的晶格参数a为1.035 434 nm。Sm₂FeSbO₇的带隙经估算为2.46 eV。用Sm₂FeSbO₇作为光催化剂在可见光照射下降解靛蓝胭脂红,并与氮掺杂TiO₂对比。结果表明,与掺氮TiO₂相比,Sm₂FeSbO₇在可见光照射下光催化降解靛蓝胭脂红显示出较高的光催化活性。总有机碳的减少,无机产物的逐渐形成,SO₄^2-和NO₃^-以及CO₂的演变揭示了在光催化过程中靛蓝胭脂红的连续矿化。检测了一些来自光催化降解靛蓝胭脂红的中间体,如邻硝基苯甲酸和邻硝基苯甲醛,并获得了可能的靛蓝胭脂红光催化降解路径。     

Ag@AgBr光催化剂的制备及其可见光催化降解亚甲基蓝反应性能

采用沉积-沉淀及光还原法制备了Ag@AgBr等离子体光催化剂,利用X射线衍射、扫描电镜和紫外-可见漫反射光谱对其进行了表征,并考察了该等离子体光催化剂在可见光(λ420nm)下的催化性能,探讨了催化剂用量、pH值、亚甲基蓝初始浓度、H2O2添加量、循环使用及捕获剂对Ag@AgBr催化性能的影响.结果表明,当亚甲基蓝的初始浓度为10mg/L,催化剂用量为1g/L,pH=9.8时,光照12min后,亚甲基蓝的降解率高达96%,且样品经5次循环使用后活性基本保持不变;而少量H2O2的添加对光催化活性影响不大,过量的H2O2会降低光催化活性;乙二胺四乙酸捕获空穴后比异丙醇捕获·OH后的光催化活性降得更低.同时,对Ag@AgBr等离子体光催化剂可见光降解亚甲基蓝的催化机理进行了分析.