Cr(Ⅵ)在Mg-Al型类水滑石上的吸附-脱附性研究Ⅰ.吸附性

研究了Cr(Ⅵ)在带结构正电荷的Mg-A1型类水滑石(HTlc)上的吸附性能,考察了pH、无机电解质添加剂NaCl,NaN03,Na2S04和Na3P04及有机添加剂EDTA和柠檬酸等因素的影响,并结合红外光谱和XRD实验结果探讨了吸附机理.研究表明,Mg-Al型HTlc对Cr(Ⅵ)有很强的吸附能力,其吸附动力学和吸附等温线分别符合准二级速率方程和Langmuir方程,饱和吸附量达105 mg/g,有望成为一种优良的含Cr(Ⅵ)污水处理剂和Cr(Ⅵ)污染土壤修复剂.初始pH增大,吸附量降低.无机电解质和有机添加剂均能明显抑制Cr(Ⅵ)在HTlc上的吸附,其抑制吸附作用的强弱顺序分别为Na3PO4≥Na2SO4≥NaCl＞＞NaNO3和柠檬酸＞EDTA.Cr(Ⅵ)在HTlc上的吸附可分为层间的离子交换吸附和外表面的吸附,其中外表面的吸附层在微观上又可分为因化学键合作用而形成的内络合层和因静电作用而形成的外络合层.     

Cr(VI)在Mg-Al型类水滑石上的吸附-脱附性研究I. 吸附性

研究了Cr(VI)在带结构正电荷的Mg-Al型类水滑石(HTlc)上的吸附性能, 考察了pH、无机电解质添加剂NaCl, NaNO₃, Na₂SO₄和Na₃PO₄及有机添加剂EDTA和柠檬酸等因素的影响, 并结合红外光谱和XRD实验结果探讨了吸附机理. 研究表明, Mg-Al型HTlc对Cr(VI)有很强的吸附能力, 其吸附动力学和吸附等温线分别符合准二级速率方程和Langmuir方程, 饱和吸附量达105 mg/g, 有望成为一种优良的含Cr(VI)污水处理剂和Cr(VI)污染土壤修复剂. 初始pH增大, 吸附量降低. 无机电解质和有机添加剂均能明显抑制Cr(VI)在HTlc上的吸附, 其抑制吸附作用的强弱顺序分别为Na₃PO₄≥Na₂SO₄≥NaCl>>NaNO₃和柠檬酸＞EDTA. Cr(VI)在HTlc上的吸附可分为层间的离子交换吸附和外表面的吸附, 其中外表面的吸附层在微观上又可分为因化学键合作用而形成的内络合层和因静电作用而形成的外络合层.     

邻甲酚在类水滑石、焙烧及改性类水滑石上的吸附

用液相非稳态共沉淀法制备了Mg-Al 类水滑石(HTlc); Mg-Al HTlc 于450 ℃下焙烧得焙烧类水滑石(CHTlc); 采用结构重建法由CHTlc 制备了十二烷基硫酸根(DS－)插层(改性)类水滑石(DS·HTlc). 研究了邻甲酚在Mg-Al HTlc,CHTlc 和DS·HTlc 上的吸附行为: 邻甲酚在Mg-Al HTlc, CHTlc 和DS·HTlc 上的吸附动力学和等温式均分别符合准二级动力学方程和Freundlich 方程, 且吸附速率和吸附量大小均依次为: DS·HTlc>>CHTlc>HTlc; 在初始pH＝5.00～13.00 范围内, 邻甲酚在HTlc 和CHTlc 上的吸附量随pH 值的增加先增加后减小, 随温度的增加而增加, 邻甲酚在DS·HTlc 的吸附量随pH 值和温度的增加而降低; 邻甲酚在HTlc, CHTlc 和DS·HTlc 上的吸附量均随电解质(NaCl)浓度的增加而增加, 探讨了吸附机理. 研究结果表明, DS·HTlc 有望成为一种新型的高效酚类有机污染物处理剂.     

镁铝类水滑石在Cr(Ⅵ)和对甲基苯酚复合污染中的吸附

以Cr(Ⅵ)、对甲基苯酚为代表污染物,用实验室模拟法研究了镁铝类水滑石（Mg-Al HTlc）对Cr(Ⅵ)的吸附行为。 结果表明,在Mg-Al HTlc/Cr(Ⅵ)/对甲基苯酚体系中,吸附动力学和热力学分别符合准二级动力学方程和Langmuir吸附等温式;溶液中共存的对甲基苯酚会延缓Mg-Al HTlc对Cr(Ⅵ)的吸附速率,但会增加其对Cr(Ⅵ)的吸附量。 一方面,Cr(Ⅵ)与对甲基苯酚产生竞争吸附,竞争作用的大小和溶液中对甲基苯酚与Cr(Ⅵ)的浓度比有关;另一方面,Mg-Al HTlc对对甲基苯酚的吸附可降低体系pH值,增加Cr(Ⅵ)的吸附量,随Cr(Ⅵ)初始浓度的增加,酚离子的竞争能力相对减弱,当Cr(Ⅵ)与对甲基苯酚的质量浓度比大于3时,Cr(Ⅵ)的吸附量增加显著,去除率增强。体系温度升高使Cr(Ⅵ)的吸附量降低。     

电解质对Mg-Al HTlc溶胶聚集动力学行为的影响

采用动态光散射法研究了电解质对Mg-Al类水滑石(HTlc)溶胶聚集动力学行为的影响,发现随惰性电解质(NaCl,NaNO3)浓度的增大,Mg-Al HTlc溶胶经历稳定、慢速聚集和快速聚集三个区域,而特性吸附电解质(NaOH)在所研究的浓度范围(0～4mmol/L)内未观察到快速聚集.NaCl和NaNO3的临界聚沉浓度分别为127和180mmol/L,慢速聚集区稳定比与NaCl,NaNO3和NaOH浓度间的关系式分别为：logW=10.18-4.4410gC,logW=11.98-4.7910gC,losW=1.92-0.7410gC.NaOH诱导体系聚集的能力大大高于NaCl和NaNO3.     

镁铝类水滑石对邻、间、对甲基苯酚的吸附

采用液相非稳态共沉淀法制备了镁铝类水滑石（Mg-Al HTlc）,并研究了邻、间和对甲基苯酚在Mg-Al HTlc上的吸附行为。 结果表明,邻、间和对甲基苯酚在Mg-Al HTlc上的吸附等温方程均符合Freundlich吸附等温式;吸附动力学均符合准二级动力学方程;在实验范围内,Mg-Al HTlc对三者的吸附量为：对甲基苯酚＞邻甲基苯酚＞间甲基苯酚;在pH值5.00~13.00范围内,三者的吸附量均随pH值的增加先增大后减小、随温度升高和电解质（NaCl）浓度的增大而增大。 探讨了吸附机理和苯环上甲基取代基位置对吸附的影响。     

类水滑石对低取代度阳离子淀粉的吸附行为

研究了低取代度阳离子淀粉（CS-L）在Mg-Al类水滑石（HTlc）上的吸附行为。 CS-L可在带结构正电荷的Mg-Al HTlc表面吸附,吸附方程符合Langmuir等温式,300 min左右达吸附平衡,饱和吸附量为33.92 mg/g。 吸附驱动力可能缘自于：CS-L醚键或羟基与HTlc羟基之间形成氢键;熵效应,即吸附所引起的CS的熵减少小于被吸附水释放引起的熵增加。 随着pH值的增加,CS-L和HTlc的Zeta电位均降低,二者静电排斥作用减小,吸附量增加;惰性电解质NaCl和CaCl2的加入可屏蔽HTlc与CS-L之间及CS-L分子内带正电的链段之间的静电排斥力,吸附量增加;pH=9时,带负电的Al八面体多聚体容易吸附在带结构正电荷的HTlc表面进而吸附CS分子,吸附量显著增加;温度升高降低二者氢键作用,吸附量降低。 比较了CS-L与高取代度阳离子淀粉（CS-H）在Mg-Al HTlc上的吸附行为。     

无机离子对Ag_3PO_4可见光降解亚甲基蓝的影响

以亚甲基蓝(MB)为模拟废水污染物,Ag3PO4为光催化剂,固定污染物初始浓度、催化剂用量、光照强度和照射时间等,探讨不同浓度的无机阴、阳离子(NO-3、Cl-、SO2-4、Na+、Ca2+、Mg2+、Al 3+)对Ag3PO4光催化降解偶氮染料MB的影响.结果表明,Na+和NO-3对Ag3PO4光催化降解MB没有明显的影响;Cl-在一定程度上对MB的降解具有促进作用;SO2-4、Ca2+、Mg2+、Al3+在不同程度上抑制了该光催化反应的进行,且抑制顺序为SO2-4Ca2+Mg2+Al 3+.     

不同复合体系对含钛高炉渣光催化还原Cr(VI)影响

采用煅烧的硫酸盐掺杂的含钛高炉渣(sulfate-modified titanium-bearing blast furnace slag,STBBFS)作为光催化剂,研究了Cr(VI)-柠檬酸[Cr(VI)-CA]复合体系和Cr(VI)-柠檬酸-硝酸铁[Cr(VI)-CA-FN]复合体系对STBBFS催化剂光催化活性的影响.结果表明:酸性条件下,不同复合体系对STBBFS催化剂光催化活性的促进作用按Cr(VI)-CA-FN复合体系>Cr(VI)-CA复合体系>Cr(VI)单一体系增强.Cr(VI)-CA复合体系在pH=2.5,反应50 min后STBBFS催化剂光催化活性为0.426 mg·min-1·g-1时将溶液中的Cr(VI)全部还原;而Cr(VI)-CA-FN复合体系在pH=2.5,反应16 min后STBBFS催化剂光催化活性为1.2425 mg·min-1·g-1时将溶液中的Cr(VI)全部还原.两种复合体系中,Cr(VI)离子的光催化还原过程都遵循L-H动力学规律,虽然加入CA和FN后,降低了吸附对光催化还原Cr(VI)的影响,但是Cr(VI)吸附至催化剂表面仍然是整个反应过程的关键.     

不同复合体系对含钛高炉渣光催化还原Cr(VI)的影响

采用煅烧的硫酸盐掺杂的含钛高炉渣(sulfate-modified titanium-bearing blast furnace slag, STBBFS)作为光催化剂, 研究了Cr(VI)-柠檬酸[Cr(VI)-CA]复合体系和Cr(VI)-柠檬酸-硝酸铁[Cr(VI)-CA-FN]复合体系对 STBBFS催化剂光催化活性的影响. 结果表明: 酸性条件下, 不同复合体系对STBBFS催化剂光催化活性的促进作用按Cr(VI)-CA-FN复合体系＞Cr(VI)-CA复合体系＞Cr(VI)单一体系增强. Cr(VI)-CA复合体系在pH＝2.5, 反应50 min后STBBFS催化剂光催化活性为0.426 mg•min―1•g―1时将溶液中的Cr(VI)全部还原; 而Cr(VI)-CA-FN复合体系在pH＝2.5, 反应16 min后STBBFS催化剂光催化活性为1.2425 mg•min―1•g―1时将溶液中的Cr(VI)全部还原. 两种复合体系中, Cr(VI)离子的光催化还原过程都遵循L-H动力学规律, 虽然加入CA和FN后, 降低了吸附对光催化还原Cr(VI)的影响, 但是Cr(VI)吸附至催化剂表面仍然是整个反应过程的关键.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.