Research and application of coupled two-dimensional asymmetric bistable stochastic resonance system

Considering that the vibration signal of rolling bearing is very weak and difficult to be extracted under the working environment noise, a two-dimensional asymmetric bistable system (TDAB) is proposed. The system is coupled by two systems, and the weak signal is enhanced by adjusting the control system (monostable system) to adjust the controlled system (asymmetric bistable system). First, under the condition of adiabatic approximation system, the signal-to-noise ratio (SNR) is deduced, and analyzes the influence of different system parameters on the shape of potential function. Then the effects of each parameter on the SNR of the system are analyzed theoretically. Finally, combined with the adaptive intelligent algorithm, the parameters of the controlled system are optimized, and then the coupling coefficient and control system parameters are adjusted to obtain better system performance. The TDAB system obtained is applied to different bearing fault diagnosis and compared with different coupling systems. The experimental results show that the method can extract the characteristic frequency effectively and has good spectrum amplification performance and anti-noise capability. It is proved that the TDAB system can also have good detection effect in practical application.     

Two-scale models of polycrystals: Evaluation of validity of Ilyushin’s isotropy postulate at large displacement gradients

This paper discusses multiscale models of inelastic deformation of single- and polycrystals, which are based on crystal plasticity theories, as applied to the verification and justification of Ilyushin’s isotropy postulate (in a special form) at large displacement gradients. Different approaches to motion decomposition on the macroscale into quasi-rigid (described by the motion of a corotational coordinate system) and strain-induced motion (a relatively moving coordinate system) are considered. The strain path is defined in terms of a moving coordinate system. Corresponding kinematic effects are defined in terms of a laboratory coordinate system. In this case, the loading process image is constructed and loading conditions are specified in terms of the moving coordinate system. Calculations are performed for two types of strain paths with different curvature by assuming two different hypotheses about quasi-rigid motion on the macroscale: (i) the spin of the moving coordinate system is equal to an averaged mesoscale spin, and (ii) the spin is equal to the macroscale vortex. It is shown that the isotropy postulate is more valid in the case of assuming the first hypothesis.     

Collins Model and Phase Diagram of 2D Ternary System

The Collins model is introduced into the two-dimensional (2D) alternative ternary system having the Lennard-Jones (L-J) potential. The Gibbs free energy of this ternary system is calculated, and according to thermodynamic theory, a group of equations that determine the solid-liquid diagram of ternary system are derived, some isothermal sectional diagrams of the 2D ternary system are obtained. The results are quite similar to the behavior of three-dimensional substances.     

Residual symmetry,interaction solutions,and conservation laws of the(2+1)-dimensional dispersive long-wave system

We explore the(2+1)-dimensional dispersive long-wave(DLW) system. From the standard truncated Painlev′e expansion, the B¨acklund transformation(BT) and residual symmetries of this system are derived. The introduction to an appropriate auxiliary dependent variable successfully localizes the residual symmetries to Lie point symmetries. In particular, it is verified that the(2+1)-dimensional DLW system is consistent Riccati expansion(CRE) solvable. If the special form of(CRE)-consistent tanh-function expansion(CTE) is taken, the soliton-cnoidal wave solutions and corresponding images can be explicitly given. Furthermore, the conservation laws of the DLW system are investigated with symmetries and Ibragimov theorem.     

Graphical Models in Reconstructability Analysis and Bayesian Networks

Reconstructability Analysis (RA) and Bayesian Networks (BN) are both probabilistic graphical modeling methodologies used in machine learning and artificial intelligence. There are RA models that are statistically equivalent to BN models and there are also models unique to RA and models unique to BN. The primary goal of this paper is to unify these two methodologies via a lattice of structures that offers an expanded set of models to represent complex systems more accurately or more simply. The conceptualization of this lattice also offers a framework for additional innovations beyond what is presented here. Specifically, this paper integrates RA and BN by developing and visualizing: (1) a BN neutral system lattice of general and specific graphs, (2) a joint RA-BN neutral system lattice of general and specific graphs, (3) an augmented RA directed system lattice of prediction graphs, and (4) a BN directed system lattice of prediction graphs. Additionally, it (5) extends RA notation to encompass BN graphs and (6) offers an algorithm to search the joint RA-BN neutral system lattice to find the best representation of system structure from underlying system variables. All lattices shown in this paper are for four variables, but the theory and methodology presented in this paper are general and apply to any number of variables. These methodological innovations are contributions to machine learning and artificial intelligence and more generally to complex systems analysis. The paper also reviews some relevant prior work of others so that the innovations offered here can be understood in a self-contained way within the context of this paper.     

新型双级间接蒸发冷却系统性能理论研究

本文提出了一种新型双级间接蒸发冷却(IEC-TIEC)系统,其中普通叉流回热式间接蒸发冷却器(IEC)与热电辅助间接蒸发冷却器(TIEC)串联运行。建立了该系统的物理及数学模型,在不同热电制冷模块的运行参数(工作电流及模块数量)条件下,对比分析了新型双级间接蒸发冷却系统与单级热电辅助间接蒸发冷却(TIEC)系统的性能,结果表明IEC-TIEC系统的COP与露点效率均优于单级TIEC系统;研究了一次空气入口参数(温度、相对湿度、质量流量)对IEC-TIEC系统的COP与露点效率的影响规律。此外,对系统的四种不同质量流量分配比进行了优化分析,结果表明,存在最佳的质量流量分配比使得系统COP最大;在系统总换热面积一定的约束条件下,对系统中叉流回热式间接蒸发冷却器换热面积占系统总换热面积的比值进行了优化。     

新型双级间接蒸发冷却系统性能理论研究

本文提出了一种新型双级间接蒸发冷却(IEC-TIEC)系统,其中普通叉流回热式间接蒸发冷却器(IEC)与热电辅助间接蒸发冷却器(TIEC)串联运行。建立了该系统的物理及数学模型,在不同热电制冷模块的运行参数(工作电流及模块数量)条件下,对比分析了新型双级间接蒸发冷却系统与单级热电辅助间接蒸发冷却(TIEC)系统的性能,结果表明IEC-TIEC系统的COP与露点效率均优于单级TIEC系统;研究了一次空气入口参数(温度、相对湿度、质量流量)对IEC-TIEC系统的COP与露点效率的影响规律。此外,对系统的四种不同质量流量分配比进行了优化分析,结果表明,存在最佳的质量流量分配比使得系统COP最大;在系统总换热面积一定的约束条件下,对系统中叉流回热式间接蒸发冷却器换热面积占系统总换热面积的比值进行了优化。     

加速器驱动次临界系统注入器离子源控制系统

强流质子源及低能传输线是加速器驱动次临界系统(ADS)项目注入器的重要组成部分,为了保证其工作效率设计了一种基于实验物理及工业控制系统(EPICS)架构的远程控制系统。根据被控设备硬件接口的特点及控制需求分别采用可编程控制器(PLC)和串口服务器等作为控制部件,在主控机中使用LabVIEW编程实现了对系统内所有设备的监控,并借助于DSC模块把设备状态和参数等以过程变量的形式进行网络发布。设计的控制系统具有结构简单、工作可靠的特点,已经在系统调试中发挥了重要作用。     

Notes on Multi-linear Variable Separation Approach

The multi-linear variable separation approach method is very useful to solve (2+1)-dimensional integrable systems. In this letter, we extend this method to solve (1+1)-dimensional Boiti system, (2+1)-dimensional Burgers system, (2+1)-dimensional breaking soliton system, and (2+1)-dimensional Maccari system. Some new exact solutions are obtained and the universal formula obtained from many (2+1)-dimensional systems is extended or modified.     

3维VSP光纤检波器井下地震采集系统

介绍了一种用于石油勘探的井下3维VSP(Vertical Seismic Profile)采集系统设计方案,实验验证该系统达到了可测量动态范围80 dB(可测量最大值与最小之比),系统采集、处理和传输的总延时低于200 ms(2 kbit/s采样率)的指标,适用于井下VSP采集.系统采用六级光纤加速度传感器组成阵列,其中每级传感器由三个麦克尔逊干涉仪构成.使用高速DSP处理芯片实现相位产生载波(Phase Generated Carrier,PGC)解调等算法以获得地震波信号;同时应用多个ARM处理器设计光纤检波器阵列控制器以及阵列内部总线.     

激光干扰红外成像系统的噪声等效温差及信噪比分析

噪声等效温差(NETD)和信噪比(SNR)是衡量红外成像系统性能的重要指标之一,它与探测器的多种性能参数有关。分析了激光辐照干扰红外探测系统及不同材料类型红外探测器性能参数变化。通过理论定量计算分析,比对YAG激光(波长1.06 μm)干扰前后系统噪声等效温差、信噪比曲线,得到了激光损伤后的NETD比损伤前NETD大2至3个数量级,同时,激光干扰后的信噪比相对激光干扰前信噪比小2个多数量级,进一步推导出激光干扰对红外探测系统的影响。     

成像型速度干涉仪

 介绍了应用于超高压条件下的成像型速度干涉仪技术的光路结构和基本原理,该技术在传统速度干涉仪技术的基础上进行了改进,将收光部分改为成像系统,记录系统使用条纹相机,从而能够诊断高速冲击波信号。给出了全系统的光路图,提出了各分系统的参数要求。针对系统硬件,给出了探针光源、成像系统的基本参数,给出了三点支撑干涉仪的设计图,分析了记录系统的基本参数。对于静态实验,拍摄了静态靶的照片,并对静态靶照片进行了初步的分析：发现可以通过条纹对比度的变化初步判断像与靶的对应程度。     

嵌入式预充电电源控制系统的设计与实现

研制了基于PC/104总线为核心的嵌入式预充电电源控制系统,重点阐述了该控制系统的硬件结构与软件设计;该控制系统以SBC-4680为控制系统主板,通过PC/104总线控制PCM-5120模拟量输入输出卡,控制PCM-5134的IO和定时计数卡,同时制作相应的接口电路及看门狗电路,在DOS操作系统中,利用C++编写底层软件,控制中采用PID算法及特殊数据处理方法,利用VB编写上位机操作界面与图形显示软件,实现与底层软件的以太网通信、信号的实时传输、显示与处理;实验证明,采用此预充电控制系统以后,使高压电源的波头质量得到极大提高,既消除了震荡,又避免了电压跌落等情况的出现,同时该电源的控制精度达到1%,因此,该控制系统完全满足电源控制及保护需要。     

基于嵌入式系统结构的印鉴鉴别系统

为了弥补市场上现有印鉴鉴别系统体积大、移动性能差、安全性较低、价格比较昂贵等缺陷,研究了基于高速数字信号处理器(DSP)和现场可编程门阵列(FPGA)的嵌入式印鉴鉴别系统.系统在印鉴识别算法上,基于平滑卷积的方法计算印鉴的中心位置和半径.采用径向投影法,对一维特征数据计算,得到待验印鉴(SS)与预留印鉴(MS)之间的偏转角度.把印鉴质量指标作为MS与SS对应边缘Hausdorff距离测度的控制参数,用神经网络方法综合分析、判别印鉴真伪.在硬件实现方面,片上可编程(SOPC)系统结合DSP作为检测系统核心.SOPC系统包括控制器、图像预处理器等.DSP作为系统的主处理器,用于进行图像的特征检测与识别.系统具有以太网、RS232、USB等通用接口.实验表明,该系统可以有效识别印鉴,并具有体积小、成本低、系统功能可灵活升级等特点.     

A Coupled Hybrid Lattice: Its Related Continuous Equation and Symmetries

The hybrid lattice, known as a discrete Korteweg-de Vries (KdV) equation, is found to be a discrete modified Korteweg-de Vries (mKdV) equation in this paper. The coupled hybrid lattice, which is pointed to be a discrete coupled KdV system, is also found to be discrete form of a coupled mKdV systems. Delayed differential reduction system and pure difference systems are derived from the coupled hybrid system by means of the symmetry reduction approach. Cnoidal wave, positon and negaton solutions for the coupled hybrid system are proposed.     

Coherent beam combination of adaptive fiber laser array with tilt-tip and phase-locking control

We present an experimental study on tilt-tip(TT) and phase-locking(PL) control in a coherent beam combination(CBC) system of adaptive fiber laser array.The TT control is performed using the adaptive fiber-optics collimator(AFOC),and the PL control is realized by the phase modulator(PM).Cascaded and simultaneous controls of TT and PL using stochastic parallel gradient descent(SPGD) algorithm are investigated in this paper.Two-fiber-laser-,four-fiber-laser-,and six-fiber-laser-arrays are employed to study the TT and PL control.In the cascaded control system,only one high-speed CMOS camera is used to collect beam data and a computer is used as the controller.In a simultaneous control system one high-speed CMOS camera and one photonic detector(PD) are employed,and a computer and a control circuit based on field programmable gate array(FPGA) are used as the controllers.Experimental results reveal that both cascaded and simultaneous controls of TT using AFOC and PL using PM in fiber laser array are feasible and effective.Cascaded control is more effective in static control situation and simultaneous control can be applied to the dynamic control system directly.The control signals of simultaneous PL and TT disturb each other obviously and TT and PL control may compete with each other,so the control effect is limited.     

基于空间光调制器的计算全息成像特性

把基于高分辨空间光调制器(SLM)的动态计算全息波面变换系统看作一个相干光学成像系统,分析并推导了该系统的点扩展函数（PSF）,进而研究了SLM像素结构所引起的固有切趾和展宽效应. 通过计算机模拟考察了SLM填充因子和衍射距离对系统分辨率的影响,给出了满足抽样定理所要求的系统的最小衍射距离. 最后提出了一种消除SLM像素结构影响的物波频谱预处理方法. 这一研究为优化系统设计,完善波面变换系统提供了新的途径.     

基于GPS的XP系统下海量图像多机同步采集方法研究

根据惯性导航系统的测试需求,利用RAID等先进技术,构建了一套图像采集存储系统,解决了多摄像机同步工作、大分辨率图像的高速采集和海量数据实时存储的问题。为了解决多设备之间的数据对齐问题,利用GPS秒脉冲和绝对时标以GPS系统实时时钟为基础,并对Windows系统进行高精度定时产生摄像机的外触发信号,实现了不同设备之间的实时数据采集、对齐。试验表明:该测试系统的配置灵活,同步精度高,具有较好的推广使用价值。     

Control analysis of the tunable phononic crystal with electrorheological material

The elastic band structure of a two-dimensional phononic crystal (PC) with electrorheological (ER) material is investigated and the plane-wave-expansion (PWE) method is adopted to solve the problem in this paper. The ER material is used to act as a tunable elastic composite inserts and its material parameter can be changed by the applied electric fields. Variations of the band gaps for the phononic composite system are also calculated with various electric fields and it is found to have a significant effect on the band gaps of the phononic system with ER material inserts. The band gaps of the smart system can be controlled and the acoustic characteristics of the system are also changed by applied different electric fields.     

Passive control and synchronization of hyperchaotic Chen system

This paper investigates the control and synchronization of hyperchaotic Chen system based on the passive theory. By using two outputs, novel passive controllers are respectively designed to realize the globally asymptotical stability of the hyperchaotic Chen system and the error dynamical system, which avoids mistakes in Ref.[11], where function W（z） cannot guarantee that fo（z） is globally asymptotically stable via only one output and W（z） is the Lyapunov function of f0（z）. Furthermore, numerical simulations are given to show the effectiveness of our method.