基于相位调制器产生六倍频光毫米波的OFDM信号光传输系统研究

提出了两个并行相位调制器产生六倍频光毫米波并传输正交频分复用信号的全双工光纤无线通信系统.将2.5Gbt/s的正交频分复用信号调制到60GHz光毫米波上.从理论上分析了毫米波产生的原理,并分别模拟了毫米波信号承载OOK信号和正交频分复用信号在光纤中的传输性能.从而验证系统的可行性.仿真模拟结果表明,在光纤无线通信系统中,正交频分复用比非归零码更具有优势.     

光相位调制器和光强度调制器产生40GHz光载OFDM毫米波信号的传输性能比较

实验研究了分别采用光相位调制器和光强度调制器产生40GHz光载正交频分复用(OFDM)信号的毫米波光纤无线通信(ROF)系统,并比较了二者的传输性能。在中心站,将20GHz的射频(RF)正弦波信号与2.5Gb/s的OFDM信号混频后驱动相位调制器或强度调制器进行双边带(DSB)调制,产生的光载OFDM信号的毫米波经标准单模光纤(SSMF)传输到基站。在基站,经光纤布拉格光栅(FBG)滤除中心载波后的光调制信号经光电检测器转换成电调制信号,再与射频信号混频,恢复出基带OFDM信号,而分离出来的中心载波信号可以用于实现波长重用。实验验证了OFDM信号峰值-平均(峰均)功率比大小对系统误码率的影响。实验结果显示,在大入纤功率情况下,相位调制和强度调制产生的毫米波光信号经过50kmSSMF传输后,其功率代价分别为小于0.5dB和大于1dB。说明光相位调制器产生光载毫米波加载OFDM信号在光纤中的传输性能优于光强度调制器。     

基于数字相干叠加的相干光正交频分复用系统中光纤非线性容忍性研究

光正交频分复用系统中的光纤非线性效应制约着系统进一步的扩容. 针对此问题, 提出一种数字相干叠加的方法, 用于提高相干光正交频分复用系统对光纤非线性的容忍性. 仿真中, 5通道的波分复用下偏振复用相干光正交频分复用系统的每个通道传输四进制正交振幅调制映射的71.53 Gbit/s信号在光纤中传输400 km. 首先, 通道间隔为25 GHz, 与传统相干光正交频分复用系统相比, 色散补偿前后, 使用数字相干叠加的相干光正交频分复用系统的信噪比分别提升了6.02 dB和9.05 dB, 最佳入纤光功率均增大了2 dB; 其次, 通道间隔为50 GHz, 色散补偿前后, 信噪比分别提升了4.9 dB和8.75 dB. 通过理论推导及仿真, 验证了所提方法能有效消除相干光正交频分复用系统的一阶非线性失真, 进而提高系统对光纤非线性的容忍性.     

承载正交频分复用信号的58GHz光载毫米波波分复用光纤无线通信系统

实验研究了一种采用马赫-曾德尔强度调制器和光交叉复用器(IL)产生58 GHz光载毫米波传输正交频分复用(OFDM)信号的波分复用光纤无线通信(WDM-ROF)系统。中心站的4路连续光波耦合后输入射频(RF)信号频率为29 GHz的强度调制器进行双边带(DSB)调制,再用另一个强度调制器将2.5 Gb/s的OFDM信号调制到DSB信号上。经20 km单模光纤(SMF)传输至基站,通过IL将中心载波和一阶边带分离。经可调谐光滤波器(TOF)滤取所需信道的一阶边带,由高速光电检测器产生58 GHz的电毫米波,利用相干解调恢复下行OFDM基带数据信号。实验结果表明,在无色散补偿和误码率为10-3的条件下,下行OFDM信号经光纤传输20 km后的功率代价小于0.5 dB,而且星座图依然清晰。     

基于新型偏振稳定毫米波发生器的光载无线通信下行链路

为了降低ROF系统成本,增加传输距离,提高系统性能, 提出了一种基于新型偏振稳定毫米波发生器的光载无线通信下行链路传输系统.与传统ROF系统相比, 该系统利用保偏光纤光栅选频产生的两个偏振稳定激光信号拍频产生毫米波, 易于实现并降低了功率噪声对系统的影响.仿真分析了该系统中环形激光器强度、谱线宽度、保偏光纤光栅反射谱特性对毫米波性能的影响;分析了系统中保偏光纤光栅的群时延、长度、色散,双波长激光信号脉冲包络宽度、啁啾系数对毫米波频率的影响.优化保偏光纤参数, 差频产生60 GHz的毫米波信号,并分析该毫米波信号在ROF下行链路的传输性能,结果表明该毫米波 作为副载波调制到光波上从中心站传输80 km至基站后经天线发射至用户端,解调仍然得到很好的眼图, 充分证明了本方案的优越性能.     

长距离和多模接入网络中低密度奇偶校验-正交频分复用的性能研究

研究了低密度奇偶校验编码与正交频分复用相结合的编码调制技术,从理论上分析了光纤链路中色散和频率选择性衰落的影响,并通过数值模拟仿真,比较了不同编码码率的编码调制信号在长距离单模光纤传输和多模光纤接入网络中的传输性能.仿真结果表明,采用码率为0.75的长码型非规则的低密度奇偶校验编码与正交频分复用相结合的编码调制技术更适合光纤通信系统中的长距离传输和多模接入网络.     

基于偏振稳定双波长保偏光纤光栅激光器的可调谐微波/毫米波产生技术

首次提出了一种基于偏振稳定双波长保偏光纤光栅激光器的可调谐微波/毫米波产生技术, 利用保偏光纤光栅选频产生两个偏振稳定的激光信号, 采用扰偏器确保激光输出的两个正交偏振态功率的一致性, 最后输入高速光电探测器产生微波/毫米波. 通过对保偏光纤光栅施加不同大小的侧向应力, 可以灵活调谐输出的毫米波频率. 实验制作了基于偏振稳定双波长保偏光纤光栅激光器的可调 谐微波/毫米波产生装置, 通过对保偏光纤光栅施加不同的轴向拉力分别产生了20.407 和22.050 GHz的微波信号. 仿真产生了60 GHz的毫米波信号, 并分析该毫米波在光纤无线通信下行链路的传输性能, 结果表明该毫米波作为副载波调制到光波上从中心站传输80 km至基站后经天线发射至用户端, 解调后仍然得到很好的眼图, 充分证明了本方案的优越传输性能.     

长距离和多模接入网络中低密度奇偶校验-正交频分复用的性能研究

研究了低密度奇偶校验编码与正交频分复用相结合的编码调制技术,从理论上分析了光纤链路中色散和频率选择性衰落的影响,并通过数值模拟仿真,比较了不同编码码率的编码调制信号在长距离单模光纤传输和多模光纤接入网络中的传榆性能.仿真结果表明,采用码率为0.75的长码型非规则的低密度奇偶校验编码与正交频分复用相结合的编码调制技术更适...     

基于动态混沌映射的三维加密正交频分复用无源光网络

提出了一种基于混沌映射的三维加密正交频分复用无源光网络保密通信系统.该系统通过相关性检测锁定收发端混沌系统参数,实现收发双方混沌系统同步;并利用同步混沌系统生成密钥,实现符号扰动以及二重子载波加密.该加密方案的密钥空间超过10~(86),能够有效对抗穷举攻击.实验实现了13.3 Gb/s基于64进制正交幅度调制的加密正交频分复用信号在25 km标准单模光纤中的传输,并完成了信息的有效解密.     

采用OFDM信号作为标记的光分组交换方案

以光正交频分复用信号作为光标记,利用两个不同波长的光载波分别经过强度调制,产生了10 Gb/sOOK光载荷和2.5 Gb/sOFDM光标记。测得了光分组信号经光纤传输前后接收载荷的眼图和标记的星座图以及误码率曲线,结果表明:经过40 km光纤传输后,载荷与标记的功率代价分别为1dB和0.5dB。     

一种改进的双边带调制产生光毫米波的方案

提出了应用于光纤无线通信系统中一种改进的双边带调制产生光毫米波方案。在中心站采用强度调制将射频信号调制到光载波上产生一个双边带信号,滤掉中心载波后,利用光交叉复用器把双边带信号的上下边带模分开,将数据速率为2.5Gbit/s的基带信号调制到下边带模后,再与未调信号耦合后产生光毫米波,然后通过单模光纤传输至基站,在基站经过光电转换后产生电毫米波信号。从理论上对该毫米波的色散特性进行了分析,发现毫米波的接收功率不会周期的衰减。同时通过实验研究表明,下行链路信号通过光纤能传输50km而不需要色散补偿,功率代价小于1dBm。因此,该方法产生的光毫米波能有效克服光纤色散引起的信号时延而导致的基带信号退化,适合于远距离传输。     

RoF downlink transmission system using FWM effect of SOA for generating MM-Wave

We propose a millimeter wave radio-over-fiber system to provide downlink service by using four-wave-mixing effect in semiconductor optical amplifier for millimeter-wave generation. At the central station, microwave source is 5.4-GHz. The optical carrier suppression modulation scheme and semiconductor optical amplifier are employed to simultaneously generate 32.4-GHz (sextuple fundamental) optical millimeter wave and up-convert data signal. At the base station, the downstream is received by a high-speed photodiode and base data are recovered by an electrical mixer. Theoretic analysis and experimental results show that the downlink 2.5-Gb/s data is successfully transmitted over 20-km single mode fiber with less than 0.15-dB power penalty.     

一种基于光纤光栅的毫米波副载波光纤通信方案

提出了一种采用光纤光栅滤波器获得具有一定间隔双波长成分的光脉冲光谱实现毫米波副载波光信号产生的方法。利用逆工程算法,设计了一种变迹叠栅(Moiré)光纤光栅滤波器,给出了相应的模拟结果;并在实验上初步制作了相应的光纤光栅滤波器,验证其可行性。同时基于所设计的光纤光栅和波分复用技术,提出了一种频移键控光纤无线通信系统Radio Over Fiber系统,为下一代的高速大容量的光纤无线通信系统系统提供一种可行的备选解决方案。     

Reduction of frequency fading and imperfect frequency response with pre-emphasis technique in OFDM-ROF systems

In this paper, a novel technique is proposed and experimentally demonstrated to reduce the effect of frequency fading (FF) and imperfect frequency response in direct-detection (DD) optical orthogonal frequency division multiplexing-radio-over-fiber (OFD-MROF) systems. To overcome FF effect in the optical fiber and imperfect frequency response in the optical and electrical devices at the high frequency, we pre-emphasize the power of the millimeter wave (mm-wave) OFDM sub-carriers appropriately in the center station. Experimental result of the proposed system shows the received sensitivity has been improved about 2 dB at the BER of 1 × 10^− 4 after 50 km SSMF transmission for 2.5 Gb/s OFDM signal carried on 60 GHz optical mm-wave compared to the original system without pre-emphasis technique.     

An Optical Carrier Generation Approach for Cellular Millimeter-Wave Radio Systems

An optical carrier generation approach is presented for cellular millimeter-wave radio systems. The well-known methods distribute the millimeter wave signal via fibers. They have drawbacks because they need very high-speed photonic compo nents that are expensive. This problem is overcome by the new approach utilizing an optically transmitted low-frequency reference signal to generate the millimeter wave carrier. The new approach applies inexpensive photonic components and is less sensitive to the fiber dispersion.     

An Optical Carrier Generation Approach for Cellular Millimeter-Wave Radio Systems

An optical carrier generation approach is presented for cellular millimeter-wave radio systems. The well-known methods distribute the millimeter wave signal via fibers. They have drawbacks because they need very high-speed photonic compo nents that are expensive. This problem is overcome by the new approach utilizing an optically transmitted low-frequency reference signal to generate the millimeter wave carrier. The new approach applies inexpensive photonic components and is less sensitive to the fiber dispersion.     

A multi-channel full-duplex 60-GHz-band radio-over-fiber system

We propose and simulate a novel full-duplex radio-over-fiber system using a single light source at central station (CS). The scheme is employed to generate 60-GHz optical millimeter wave at CS for down-link transmission while the same optical carrier is reused at base station for up-link connection. There is no additional laser source for the upstream data generation in the base station. The bidirectional full-duplex 2.5 Gb/s data are successfully transmitted over 40 km standard single-mode fiber (SMF). The power penalty for the down-link data after transmission over 40 km SMF is less than 0.6 dB, while for the up-link data, the power penalty after transmission over 40 km SMF is neglected. This system shows good performance over long-distance delivery and has important applicable value in high radio frequency (RF) sector and multi-channel full-duplex system.     

DSB optical mm-wave with signal only on optical carrier generated by embedded LiNbO3 Mach-Zehnder modulator

We have investigated the generation of the 40-GHz double-sideband optical millimeter (mm)-wave with signal carried only by its optical carrier via an embedded LiNbO₃ Mach-Zehnder modulator (LN-MZM). Since the optical carrier and its two first-order sidebands are dominant and their powers are well balanced, the first-order harmonic in the photocurrent gets maximal. As the optical mm-wave signal is transmitted along the fiber, there is no code outline distortion because the signal is only modulated on the optical carrier. Although the first-order harmonic shows the periodical fading effect when the optical mm-wave signal is transmitted along the fiber, its degradation on the radio-over-fiber link can be avoided by adjusting the position of the fading nodes via varying the main MZM bias voltage, and the signal still keeps much good eye diagram even after 50-km fiber transmission. The experimental results prove our theory.     

Ultra-broadband OFDM signal generation for 1-Tb/s super-channel coherent optical OFDM transmission

A 320.6-GHz multi-band optical OFDM signal generation scheme consisting of continuous 4,104 subcarriers is demonstrated for 1-Tb/s coherent optical OFDM (CO-OFDM) transmission. The 36 uncorrelated orthogonal bands are generated using a recirculating frequency shifter (RFS) with single laser by adjusting the loop delay of RFS to be an integer multiple of OFDM symbol period. The principle and performance of this generation scheme is studied theoretically and experimentally. The 1-Tb/s CO-OFDM signal is successfully received after 600-km SSMF fiber transmission without any dispersion compensation.