酚醛型吸附树脂对咖啡因和茶碱吸附性能的研究

用静态和动态方法研究了酚醛型吸附树脂JDW-2和DuoliteS-761对咖啡因和茶碱的吸附行为.结果表明,自制树脂JDW-2对咖啡因和茶碱的吸附性能明显优于DuoliteS-761.树脂的比表面积、含水量、酚羟基的含量与吸附关系密切,尽管JDW-2的比表面积比DuoliteS-761小,但前者比后者具有更高的含水量(42%)和酚羟基含量(3.72mmol/g).在静态条件下,JDW-2吸附咖啡因的速率比DuoliteS-761快,JDW-2树脂对咖啡因和茶碱饱和吸附量分别为246和127mg/g干树脂,而DuoliteS-761树脂对它们的吸附量分别为121和53mg/g干树脂;JDW-2和DuoliteS-761吸附咖啡因的初始阶段是粒扩散控制过程;酚醛型吸附树脂等温吸附咖啡因和茶碱的平衡吸附数据符合Langmuir方程.酚醛型吸附树脂吸附咖啡因和茶碱属单分子层吸附.在动态条件下,1mol/LHCl和40%甲醇溶液以1.5BV/h来洗脱吸附咖啡因的JDW-2,在4～5个床体积的洗脱率分别是88%和93%,而1mol/LHCl和80%甲醇溶液以1.5BV/h来洗脱吸附茶碱的JDW-2,在3～4个床体积的洗脱率分别是91%和96%,表明酚醛型吸附树脂具有良好的洗脱性能,用1mol/LHCl和40%(或80%)甲醇溶液作复合洗脱剂从JDW-2中洗脱咖啡因(或茶碱),效     

超高交联树脂的氯代烷烃后交联法制备及对咖啡因的吸附研究

以三氯甲烷为外交联剂,以AlCl3为催化剂,经Friedel-Crafts后交联反应将大孔低交联聚苯乙烯（PS）后交联,制备得到超高交联聚苯乙烯树脂HCPS-C₁,树脂的BET比表面积从PS的19.5m²/g提高到HCPS-C₁的522m²/g;再以1,2-二氯乙烷为外交联剂,以FeCl₃为催化剂,将HCPS-C₁后交联,制备得到了比表面积高达791m²/g的超高交联聚苯乙烯树脂HCPS-C₁-C₂。测定了HCPS-C₁和HCPS-C₁-C₂对咖啡因的吸附性能,并与商用树脂XAD4及氯甲基化聚苯乙烯后交联树脂HCPS-CM进行对比,结果表明,HCPS-C₁有着接近于XAD4对咖啡因的吸附量,而HCPS-C₁-C₂对咖啡因的吸附量远高于XAD4,且略高于HCPS-...     

丙烯酸酯基吸附树脂对水体中单宁酸和没食子酸的吸附研究

选用3种商品丙烯酸酯基吸附树脂作为吸附剂,研究单宁酸和没食子酸在树脂上的吸附行为和机理。吸附等温线表明,丙烯酸酯基吸附树脂对单宁酸的吸附量远高于没食子酸的吸附量,这归因于两种有机酸亲水性的差异;HP-2MG比其他两种树脂对单宁酸有更高的吸附容量,而XAD-7树脂对没食子酸的吸附量高于其它两种丙烯酸酯基吸附树脂,这归因于树脂比表面积和孔径的差异;吸附热力学研究表明,丙烯酸酯基吸附树脂对天然有机酸的吸附是自发的放热过程,疏水作用是主要吸附作用。     

酚醛型吸附树脂对咖啡因吸附性能的研究

利用 3种自制吸附树脂JDW 1、JDW 2、JDW 3和DuoliteS 761对咖啡因进行了静态和动态吸附研究 .结果发现 3种自制树脂对咖啡因的吸附性能明显优于DuoliteS 761 ;在吸附咖啡因的初始阶段 ,即达到 3 2 %～5 1 %平衡吸附百分率时 ,吸附速率数据和半经验速率方程很吻合 ,证实吸附咖啡因是粒扩散控制过程 ;酚醛型吸附树脂等温吸附咖啡因的平衡吸附数据符合Langmuir方程 ,相关系数在 0 99以上 ,因此 ,酚醛型吸附树脂吸附咖啡因属单分子层吸附 ;用 1mol LHCl和 40 %的甲醇溶液复合使用 ,效果很好     

大孔吸附树脂对洋地黄强心甙吸附性能的研究.I.

本文从六种大孔吸附树脂中筛选出ＨＡ－２和ＨＡ－３二种树脂，这二种树脂对洋地黄类强心甙－－地高辛具有较好的吸附性能，测定了吸附树脂的比表面积、孔容及平均孔径，讨论了地高辛溶液的浓度、ｐＨ值等诸条件对大孔吸附树脂吸附性能的影响。     

大孔吸附树脂对盐酸阿霉素吸附性能的研究

本文选用ＨＡ－０１、ＨＡ－０２、ＨＡ－０３大孔吸附树脂对盐酸阿霉素进行静态和动态吸附实验。测定了３种大孔吸附剂的比表面积,孔容及平均孔径,讨论了吸附树脂的孔结构参数与吸附特性的关系,以及盐酸阿霉素溶液浓度,树脂用量等条件对大孔吸附树脂吸附性能的影响。     

单宁酸修饰的超高交联吸附树脂对酚类化合物的吸附研究

通过氯甲基化的苯乙烯-二乙烯苯共聚物的后交联及单宁酸的化学修饰反应制备了单宁酸修饰的超高交联吸附树脂(TAMR),通过红外光谱、元素分析、扫描电镜和比表面孔径分析对TAMR树脂的结构特征和表面参数及形貌进行表征.通过等温吸附实验和吸附动力学实验研究了苯酚、对硝基苯酚和对氯苯酚在TAMR树脂上的吸附性能和吸附机理.结果表明,TAMR树脂具有较高的比表面积(780.1 m2/g)和较丰富的微孔(482.3 m2/g),树脂表面修饰了较丰富的羟基.TAMR树脂对苯酚、对硝基苯酚和对氯苯酚均具有较好的吸附性能,288 K时吸附量分别可达1.43、2.07和2.48 mmol/g(c0为500 mg/L).3种酚类化合物在TAMR树脂上的吸附为典型的物理吸附,其吸附焓变和熵变均为负值.当酚类化合物以分子形态存在时,有利于其被TAMR树脂吸附.Langmuir和Freundlich方程均能较好地拟合酚类化合物在TAMR树脂上的吸附等温线.吸附动力学过程符合准一级动力学方程,颗粒内扩散过程是TAMR树脂吸附这3种酚的吸附速率的主要控制步骤.     

化学修饰超高交联吸附树脂对水中四环素的吸附研究

本文采用偏苯三酸酐修饰的超高交联吸附树脂(TMAMR)和羟丙基纤维素修饰的超高交联吸附树脂(HPCMR)作为吸附剂,以NDA150树脂作对照,研究了3种树脂对水中四环素的吸附性能和吸附机理,同时考察了p H值和Na+浓度对TMAMR和HPCMR树脂吸附四环素的影响。结果表明,TMAMR和HPCMR树脂的比表面积较高,树脂表面修饰了大量的羟基,对四环素均具有较好的吸附性能。3种树脂对四环素的吸附量均随着温度的升高而增大,吸附过程中同时存在较强的物理吸附和化学吸附作用。Langmuir和Freundlich等温吸附方程均能够较好地拟合吸附等温线,吸附机理较复杂。吸附热力学结果表明,四环素在3种树脂上的吸附为自发的吸热过程,且吸附过程的熵增加。p H值对TMAMR和HPCMR树脂吸附四环素有较大的影响,在中性条件下,树脂对四环素的吸附量最大,在强酸和强碱条件下树脂的吸附量均较低。吸附液中加入无机盐后,发生盐析作用,导致TMAMR和HPCMR树脂对四环素的吸附量增大。     

聚（对乙烯基苄基己内酰胺）树脂对非水体系中苯酚的吸附热力学

测定了聚（对乙烯基苄基己内酰胺）吸附树脂对正庚烷溶液中苯酚的吸附等温线,发现吸附等温线符合Freundlich等温吸附方程,相关系数大于0．99．根据热力学函数关系计算了等量吸附焓、Gibbs吸附自由能和吸附熵,等量吸附焓在30～40kJ／mol之间,推测吸附过程为氢键吸附．通过比较树脂对正庚烷中苯酚和邻硝基苯酚的吸附性能的差别,进一步论证了树脂对非水体系中酚类物质的吸附是基于氢键作用的机理．同时,聚（对乙烯基苄基己内酰胺）树脂对正庚烷溶液中苯酚的吸附相对水溶液中苯酚的吸附有更低的吸附焓变、吸附自由能变和吸附熵变．     

单宁酸修饰的后交联吸附树脂的制备及对氯酚的吸附性能

采用氯甲基化的低交联苯乙烯-二乙烯苯共聚物,通过交联反应和化学修饰反应制备了单宁酸修饰的后交联吸附树脂TAMR-1和TAMR-2,并对其进行了红外光谱分析、比表面及孔径分析和热重分析。通过静态吸附实验,比较了TAMR-1和TAMR-2对2-氯酚、4-氯酚和2,4-二氯苯酚的吸附去除率。通过小柱吸附-脱附实验,探讨了TAMR-1对3种氯酚的吸附性能。结果表明,与TAMR-2相比,TAMR-1的比表面积较高,氯残留量低,后交联反应与化学修饰反应更完全。TAMR-1和TAMR-2的外推起始分解温度均超过680K。TAMR-1树脂对3种氯酚(C0均为200mg/L)的吸附去除率均超过85%,明显高于TAMR-2树脂,且对2,4-二氯苯酚的吸附量最大。4%的NaOH溶液对吸附氯酚饱和后的TAMR-1树脂具有良好的再生效果。     

Inhibition of nitrobenzene adsorption by water cluster formation at acidic oxygen functional groups on activated carbon

The inhibition effect of nitrobenzene adsorption by water clusters formed at the acidic groups on activated carbon was examined in aqueous and n-hexane solution. The activated carbon was oxidized with nitric acid to introduce CO complexes and then outgassed in helium flow at 1273 K to remove them completely without changing the structural properties of the carbon as a reference adsorbent. The amounts of acidic functional groups were determined by applying Boehm titration. A relative humidity of 95% was used to adsorb water onto the carbon surface. Strong adsorption of water onto the oxidized carbon can be observed by thermogravimetric analysis. The adsorption kinetic rate was estimated to be controlled by diffusion from the kinetic analysis. Significant decline in both capacity and kinetic rate for nitrobenzene adsorption onto the oxidized carbon was also observed in n-hexane solution by preadsorption of water to the carbon surface, whereas it was not detected for the outgassed carbons. These results might reveal that water molecules forming clusters at the CO complexes inhibited the entrance of nitrobenzene into the interparticles of the carbon.     

Effect of the endcapping of reversed-phase high-performance liquid chromatography adsorbents on the adsorption isotherm

The retention mechanisms of n-propylbenzoate, 4-t ert-butylphenol, and caffeine on the endcapped Symmetry-C(18) and the non-endcapped Resolve-C(18) are compared. The adsorption isotherms were measured by frontal analysis (FA), using as the mobile phase mixtures of methanol or acetonitrile and water of various compositions. The isotherm data were modeled and the adsorption energy distributions calculated. The surface heterogeneity increases faster with decreasing methanol concentration on the non-endcapped than on the endcapped adsorbent. For instance, for methanol concentrations exceeding 30% (v/v), the adsorption of caffeine is accounted for by assuming three and two different types of adsorption sites on Resolve-C(18) and Symmetry-C(18), respectively. This is explained by the effect of the mobile phase composition on the structure of the C(18)-bonded layer. The bare surface of bonded silica appears more accessible to solute molecules at high water contents in the mobile phase. On the other hand, replacing methanol by a stronger organic modifier like acetonitrile dampens the differences between non-endcapped and endcapped stationary phase and decreases the degree of surface heterogeneity of the adsorbent. For instance, at acetonitrile concentrations exceeding 20%, the surface appears nearly homogeneous for the adsorption of caffeine.     

沥青基球状活性炭气相吸脱附行为研究

本文利用热重法研究了一系列沥青基球状活性炭对蒸汽及正已烷蒸汽的动态吸脱附曲线。结果表明,PSAC对苯蒸汽的吸附及再生性能优良。随吸附温度的降低、比表面积的增大、总孔容及微孔容的增大,PSAC对苯蒸汽的吸附容量增大。PSAC对正已烷的吸附速度大于对苯蒸汽的吸附速度,但其对正已烷的平衡吸附容量小于对苯蒸汽的平衡吸附容量。     

树脂填充聚醚砜纤维吸附剂对牛血清蛋白吸附性能的研究

重点研究树脂填充聚醚砜(PES)纤维吸附剂与模型蛋白质牛血清蛋白(BSA)之间的吸附与脱附行为.结果表明,蛋白质BSA在树脂填充PES纤维吸附剂中的平衡吸附过程较好地符合朗格缪尔吸附模型,树脂Lewatit CNP80ws填充PES吸附剂的最大吸附容量约为139mg BSA/g吸附剂.表面具有开孔结构的树脂填充PES纤维吸附剂的吸附速率较快,在不同结构纤维吸附剂中BSA的扩散系数在1·82×10-14~8·7×10-14m2/s范围内变化.另外,考察了BSA溶液的pH与洗脱剂等因素对吸附剂吸附与脱附性能的影响,研究结果对蛋白质的实际分离纯化具有重要的参考价值.     

Fundamental characteristics of synthetic adsorbents intended for industrial chromatographic separations

With the aim of obtaining comprehensive information on the selection of synthetic adsorbents for industrial applications, effect of pore and chemical structure of industrial-grade synthetic adsorbents on adsorption capacity of several pharmaceutical compounds was investigated. For relatively low molecular mass compounds, such as cephalexin, berberine chloride and tetracycline hydrochloride, surface area per unit volume of polystyrenic adsorbents dominated the equilibrium adsorption capacity. On the contrary, effect of pore size of the polystyrenic adsorbents on the equilibrium adsorption capacity was observed for relatively high molecular mass compounds, such as rifampicin, Vitamin B12 and insulin. Polystyrenic adsorbent with high surface area and small pore size showed small adsorption capacity for relatively high molecular mass compounds, whereas polystyrenic adsorbent with relatively small surface area but with large pore size showed large adsorption capacity. Effect of chemical structure on the equilibrium adsorption capacity of several pharmaceutical compounds was also studied among polystyrenic, modified polystyrenic and polymethacrylic adsorbents. The modified polystyrenic adsorbent showed larger adsorption capacity for all compounds tested in this study due to enhanced hydrophobicity. The polymethacrylic adsorbent possessed high adsorption capacity for rifampicin and insulin, but it showed lower adsorption capacity for the other compounds studied. This result may be attributed to hydrogen bonding playing major role for the adsorption of compounds on polymethacrylic adsorbent. Furthermore, column adsorption experiments were operated to estimate the effect of pore characteristics of the polystyrenic adsorbents on dynamic adsorption behavior, and it is found that both surface area and pore size of the polystyrenic adsorbents significantly affect the dynamic adsorption capacity as well as flow rate.     

胶原纤维吸附材料除去茶多酚中的咖啡因

以皮胶原纤维制备吸附材料，研究了这种吸附材料对茶多酚中各组分的吸附特性．结果表明，所制备的吸附材料能选择性地吸附EGCG、GCG和ECG，吸附率在90％以上；对C、EC和EGC的吸附率相对较低；对咖啡因的吸附率最小，只有11．24％．吸附后的产物经纯水淋洗和丙酮水溶液洗脱后，EGCG、GCG和ECG的总含量达到93.81％，回收率均在80%以上；而咖啡因的含量只有0．038％．进一步研究表明，皮胶原纤维吸附材料对茶多酚中不同组分的选择吸附能力与各组分的分子结构有关．     

Efficient Removal of Pb(II) from Aqueous Medium Using Chemically Modified Silica Monolith

The adsorptive removal of lead (II) from aqueous medium was carried out by chemically modified silica monolith particles. Porous silica monolith particles were prepared by the sol-gel method and their surface modification was carried out using trimethoxy silyl propyl urea (TSPU) to prepare inorganic–organic hybrid adsorbent. The resultant adsorbent was evaluated for the removal of lead (Pb) from aqueous medium. The effect of pH, adsorbent dose, metal ion concentration and adsorption time was determined. It was found that the optimum conditions for adsorption of lead (Pb) were pH 5, adsorbent dose of 0.4 g/L, Pb(II) ions concentration of 500 mg/L and adsorption time of 1 h. The adsorbent chemically modified SM was characterized by scanning electron microscopy (SEM), BET/BJH and thermo gravimetric analysis (TGA). The percent adsorption of Pb(II) onto chemically modified silica monolith particles was 98%. An isotherm study showed that the adsorption data of Pb(II) onto chemically modified SM was fully fitted with the Freundlich and Langmuir isotherm models. It was found from kinetic study that the adsorption of Pb(II) followed a pseudo second-order model. Moreover, thermodynamic study suggests that the adsorption of Pb(II) is spontaneous and exothermic. The adsorption capacity of chemically modified SM for Pb(II) ions was 792 mg/g which is quite high as compared to the traditional adsorbents. The adsorbent chemically modified SM was regenerated, used again three times for the adsorption of Pb(II) ions and it was found that the adsorption capacity of the regenerated adsorbent was only dropped by 7%. Due to high adsorption capacity chemically modified silica monolith particles could be used as an effective adsorbent for the removal of heavy metals from wastewater.     

Synthesis and Properties of Surface Molecular Imprinting Adsorbent for Removal of Pb<Superscript>2+</Superscript>

A new chitosan imprinting adsorbent using diatomite as core material was prepared by using the surface molecular imprinting technology with the Pb²⁺ as imprinted ion. The preparation process conditions of the surface molecular imprinting adsorbent were studied. The adsorbent was characterized by using Fourier transform infrared (FTIR) spectrum. FTIR spectrum indicated that it was cross-linked by epichlorohydrin. The new imprinting adsorbent could provide a higher adsorption capacity for Pb²⁺, which reached 139.6 mg/g increasing 32.3% compared with cross-linking chitosan adsorbent (the initial Pb²⁺ concentration of 600 mg/L). The adsorption velocity was quick and the equilibration time of the imprinting adsorbent for Pb²⁺ was 3 h that shortened about 40% compared with cross-linking chitosan adsorbent. It had a more wide pH range of 5–7 than that of cross-linking chitosan adsorbent. The new imprinting adsorbent can be reused for up to ten cycles without loss of adsorption capacity. In the kinetics and isotherm study, the pseudosecond order model and Langmuir model could represent the adsorption process.     

凹凸棒土粘结剂对13X分子筛吸附性能的促进作用

以凹凸棒土为粘结剂制备了13X分子筛吸附剂.研究了其孔结构、表面电性和对水、CO2和N2分子的吸附性能,并与高岭土为粘结剂的同类吸附剂进行了比较.结果表明,凹凸棒土发达的孔隙结构、大的比表面和表面负电性质有利于其吸附容量的改善,而13X/凹凸棒土中丰富的中孔促进了其对CO2的吸附速率.另外由CO2吸附热力学分析可知,CO2在13X/凹凸棒土上具有较低的吸附热,结果将有利于其在吸附剂上的脱附.     

A study of the alumina-silica gel adsorbent for the removal of silicic acid from geothermal water: increase in adsorption capacity of the adsorbent due to formation of amorphous aluminosilicate by adsorption of silicic acid

Two kinds of adsorbents (Si adsorbent and Al adsorbent) for the removal of silicic acid from geothermal water to retard the formation of silica scales were prepared using silicic acid contained in geothermal water. The Si adsorbent was prepared by evaporating geothermal water, and the Al adsorbent was prepared by evaporating geothermal water after the addition of aluminum chloride. The specific surface area of the Si adsorbent was small and it's adsorption capacity of silicic acid was low. Although the specific surface area of the Al adsorbent was also small, it was significantly increased by the adsorption of silicic acid and it's adsorption capacity was high. Based on the change in the local structure of aluminum ion by the adsorption of silicic acid, the Al adsorbent was considered to be silica particles covered with crystalline aluminum hydroxide. Moreover, it was concluded that the increase in the specific surface area of the Al adsorbent and the decrease in the zeta potential were due to the formation of an amorphous aluminosilicate with a large surface area and a negative charge (one 4-coordinated Al) by the reaction between aluminum ions and silicic acids.